Search Documents

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

By T. A. Klinefelter

ONE OF THE many services rendered by the Federal Bureau of Mines is the identification and general examination of ore and mineral samples. Many of these, coming from almost every State in the Union, are clay and shale samples. Other Government agencies, State geologists, universities, and other laboratories are often requested to make similar examinations. This publication describes methods of testing these samples. An earlier paper, published in 1943, described Bureau of Mines methods of testing such clays.3 This paper was to be followed later with another (part II) that would describe much more thorough testing than did the rather general outline of part I. Part I has been out of print for some time and needs revision, and part II was never written; hence, the present publication is designed to include part I and also those additions intended as part II. The tests presented in part I were simple, requiring only the ordinary equipment to be found in any good chemical laboratory. The second publication was to include a greater number of test procedures and information on increasing the accuracy and precision of those previously given.

Jan 1, 1957

By D. Randolph Berry

Foster-Miller Associates has developed a set of guidelines to permit hoist manufacturers, mine owners, and MESA mine inspectors to design, purchase, install or inspect a safe and effective Emergency Escape Hoist, as required by the Coal Mine Health and Safety act of 1969. A series of surveys were carried out to determine: 1. The attitudes and local needs of the MESA District Managers. 2. Current escape hoist installations. 3. Equipment available for future designs. 4. Foreign methods and equipment for mine rescue. From these survey studies, preliminary guideline objectives were developed.

Jan 1, 2012

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By V. F. Parry

This report is the first substantial description of the carbonizing process and the details of experimental work conducted at the Denver laboratories under a coopeative agreement between the Bureau of Mines and the Texas Power & Light Co. It presents the results of tests on several Texas lignites and other typical western coals that have been processed in the first pilot plant operated at Denver. Investigations on drying fine coal in the entrained and fluidized state have been under way at Bureau of Mines Denver laboratories for several years. Reports on this work were published in 1949 and 19505/ describing the theory and practice of re-moving inherent moisture from the lower -rank coals. The investigation did not include a study of the removal of surface moisture from fine fuel. Private industry in Canada became interested in the possibilities of drying fine coal, employing the closed-circuit system and techniques recommended by the Bureau. Large, commercial-scale drying units were built by a Canadian company, which successfully demonstrated that surface moisture could be removed from fine coal at high efficiency and capacity ill drying units similar in design to those developed by the Bureau.

Jan 1, 1953

By A. W. Frolli

This paper, describing the open-cut mining milling, and cyaniding methods and costs at the Yellow Aster gold mine, is one of a series being prepared by the Bureau of Mines on similar practices in the United States. It is presented primarily to show methods and costs of mining and treating low-grade gold ore on a large scale.

Jan 1, 1940

By William O. Vanderburg

This paper gives the results of a reconnaissance of the mining districts in Pershing County, Nev., made from March 9 to April 1, 1936. During the field work nearly all of the mining districts in the county were visited, and considerable data were obtained on active and inactive properties. The report covers the location of the various mining districts, nature of the deposits, information on past

Jan 1, 1936

By A. C. Burr

This progress report summarizes operating results on the gasification of natural lignite from five runs of the commercial-scale pilot plant at Grand Forks, N. Dak., during December 1946 and calendar years 1947 and 1948, when the plant was operated for 1,996 hours. A primary specific objective was to determine the useful life of the outer metal retort tube as it is influenced by corrosion and other factors under a wide range of operating conditions. A secondary objective was to develop the technology of production when generating gas with a high ratio of hydrogen to carbon monoxide in both the divided and continuous annuli. Results are summarized in graphs and tables that show hydrogen-carbon monoxide ratios from 2.3 to 9 at gas-production rates from 6 to 12 M cu. St. per hr. (thousand cubic feet per hour), or approximately 30 to 60 cu, ft. per square foot of heated retort-wall surface per hour. Gas yields ranged from 36 to 54 M cu, ft. per ton of natural lignite or 63 to 91 M cu. ft. per ton of moisture- and ash-free lignite, Production rates were higher in the divided annulus, but these represent the maximum capacity of the plant only at high hydrogen-carbon monoxide ratios when the high concentration of excess steam and low furnace temperature limit gas production. A ratio of 6 was the highest produced in the continuous annulus because mechanical Limitations of the auxiliary equipment prevented attainment of higher ratios. The lignite feed rate appears to influence the production rate more than any other individual operating variable. Heat balances for four periods when gas with ratios from 2.3 to 7.2 was produced with a lignite feed rate of about 325 pounds per hour suggest that the potential heat in the gas is lower at higher ratios, owing to increased heat losses in the excess steam. Heat-transfer rates through the retort tube in these four tests were between 1,500 and 3,000 B.t.u. per square foot per hour. These rates are much lower than those reached in many earlier tests, but no attempt was made to achieve maximum rates of heat transfer.

Jan 1, 1953

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

By P. L. Swanson, F. M. Boler

The U.S. Bureau of Mimes conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic destressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 21/2-week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 1993

By Noel N. Moebs

This report summarizes a Bureau of Mines study on the use of geotechnology to identify and reduce ground control hazards at slate quarry operations in eastern Pennsylvania. The major ground control hazard is falling rock, attributed to weathered bedding plane faults, which weaken quarry highwalls. It was demonstrated that these faults can be detected outside of the quarry perimeter using surface resistivity measurements. Falls of ice from quarry highwalls constitute a second major hazard, which requires water diversion as a basic control method. In situ stresses seemingly cause only minor problems in slate extraction although they could interact with developed stresses and lead to failure of barriers between quarries. Pull tests showed that rockbolts anchor firmly in slate and should prove effective in securing loose rock.

Jan 1, 1986

By F. E. Harris

The United States produces about 30 percent of the world output of salt. Numerous deposits occur in widely separated areas, but the leading producing States are California, Kansas, Louisiana, Michigan, New York, Ohio, Texas, Utah, and West Virginia. Although no great amount of salt is produced at present in Pennsylvania, the potential sources in that State recently aroused a good deal of interest. The United States salt industry is highly organized; it comprises fewer companies than when small crude works with primitive methods and equipment eked out salt for local needs, but concentration of output brought about by modern inventions and methods of production has improved the quality of the produce greatly and accelerated production.

Jan 1, 1939

By C. C. Popoff

The growth of the aluminum-smelting industry in the Pacific Northwest, resulting from national defense requirements, emphasized a need for local sources of alumina to supplement the alumina production shipped from the East. Because supplies of foreign bauxite were being interrupted and our domestic bauxite reserves were inadequate, it was necessary to expedite the investigation of other possible sources of alumina during World War II. A program of investigation of high-alumina clay deposits in the Northwest was carried out jointly by the Federal Geological Survey and the Federal Bureau of Mines. As part of this program the Cowlitz clay deposits near Castle Rock, Wash., were explored by the Bureau of Mines in 1942-43. These deposits are near railroads, tide-water, and Bonneville Power Administration lines and within 22 to 100 miles of 4 aluminum-reduction plants.

Jan 1, 1955

By Donald I. Bleiwas

The U.S. Bureau of Mines has evaluated the potential availability of nickel from 36 deposits or districts in 16 market-economy countries (MECs), analyzing more than 95 percent of production in those countries. This study indicates the quantity of nickel available on the basis of net production costs and total costs with a 0-pct and a 10-pct discounted cash flow rate of return (DCFROR). Costs of production are expressed in dollars per pound of recovered nickel. The study also indicates sensitivities of the cost of production to energy, labor, and other factors. The studied deposits and properties contain approximately 33 Mmt of recoverable nickel. About 26 Mmt of nickel is potentially recoverable from laterite deposits, of which 4.5 Mmt can be produced at $2.50/lb or less with a 0-pct DCFROR. Approximately 7 Mmt of nickel is potentially recoverable from sulfide deposits, of which about 6.3 Mint could be produced at $2.50/lb or less at a 0-pct DCFROR. The price of nickel averaged above $6.00/lb in 1988. Sensitivity studies performed for both laterite and sulfide deposits indicate that the total cost of producing nickel from laterites is most sensitive to increases in energy costs and that the total cost of producing nickel from sulfide deposits is most sensitive to increases in labor costs; sulfides are also affected by changes in revenues from byproducts.

Jan 1, 1991

By Michael K. Phang

The use of explosives to fragment rock generates ground vibrations which may have a detrimental effect on contiguous underground coal mine openings. Increased surface blasting by a burgeoning number of surface coal mines and quarries has caused considerable concern among underground mine operators. Ground vibration effects generated from surface mine blasting are also causing public concern. In response to this concern, the U.S. Bureau of Mines (Stagg and Engler, 1980) has measured and analyzed ground vibrations and their effects on underground and surface structures. Some of the complaints registered against the mining industry are claims of substantial material damage from vibrations generated by the blasting; others are nuisance complaints of minor damage or annoyance. In general, allegations of damage from surface blasting have been sufficiently numerous to constitute a major problem for mine operators engaged in blasting operations. They have recognized the need for more technological data to evaluate the vibration problems associated with blasting. Both the operators and the general public need adequate safeguards based upon factual data to protect their specific interests. The coal mine industry needs reliable information from which to change blasting operations to reduce the number and severity of major damage claims and eliminate the growing number of nuisance complaints. The problem is of major concern not only to coal mine operators and nearby property owners, but also to federal, state and local governments. At the same time, environmental control agencies responsible for blasting and explosives use require reasonable and appropriate guidelines to protect the miners' lives.

Jan 1, 1984

By W. L. Dare

This information circular is one of a series the Bureau of Mines plans to publish describing the methods and costs of mining uranium on the Colorado Plateau. The Big Buck mine is one of the larger underground uranium-vanadium ore mines on the plateau. The mine is about 39 miles southeast of Moab in the Big Indian mining district, San Juan County, Utah. The Big Buck claims were located late in 1947, when uranium mineralization was discovered in the Cutler formation at its outcrop along the escarpment that forms the west side of Big Indian Wash. Charles A. Steen made the first major discovery of uranium ore in the Chinle formation in the Big Indian mining district on July 6, 1952, when 14 feet of high-grade uranium ore was encountered in a diamond-drill hole drilled on his Mi Vida claim. The Big Buck ore body now being mined by Standard Uranium Corp. is a southeast extension of Steen's original discovery.

Jan 1, 1956

By Daniel Harrington

On the night of June 8, 1917, the flame of a carbide lamp accidentally set fire to the uncovered and frayed insulation of an armored power cable near the 2,400-foot level of the North Butte Mining Co.'s Granite Mountain shaft. How this insulation accidentally became exposed is explained on page 15. The highly flammable oiled fabric set fire to the shaft timbers, and as this is a downcast shaft the fire spread with great rapidity, soon filling the mine workings with smoke and gas. At the time 410 men were working underground, 247 of whom escaped by various means, but most of the 163 remaining were probably overcome soon after the lire started, and perished. Only two men were actually burned. The cause of the disaster was purely accidental. The immediate effect was the unexpected reversal of normal conditions; the ultimate effect was great loss of life and the destruction of the main hoisting shaft, putting it temporarily out of service. The work of rescue and fire fighting continued eight days. The following pages present an attempt to draw some practical conclusions and suggestions from this disaster. The property of the North Butte Mining Co. consists of about 220 acres in the northeastern part of the Butte district, Montana. Next to the Anaconda Copper Mining Co. it is the largest pro¬ducer of the district. In 1916, the year before the disaster, there were 1,160 men employed. The output was 560,947 tons of ore, which yielded 24,498,181 pounds of copper, 1,047,063 ounces of silver, 1,712 ounces of gold, and 412,953 pounds of zinc. The profit was $2,479,595. The total development work for that year was 21,694 feet. During the first half of 1917, the year of the accident, the daily tonnage of ore averaged 2,000, an increase of 400 tons over that of the year 1916.

Jan 1, 1922

Anaconda Aluminum Co. began production from a new 60,000-ton-per-year potline at Sebree, KY, which brings the total capacity of the plant to 180,000 tons per year. A strike by workers at Alcan Aluminium Corp. primary aluminum smelters at Arvida, Que., Isle Maligne, Que., and Beauharnois, Que. shut down the plants and the company announced force majeure on part of its ingot supply commitments. Kaiser Aluminum and Chemical Corp. announced plans to increase its price for primary aluminum from 60.0 cents per pound to 63.0 cents per pound effective July 1.

Jan 1, 1979

By N. P. Kripakov

The Bureau of Mines has developed a unique new mine design procedure to determine the changing static load distributions imposed on under-ground support structures during the mining cycle. The procedure reduces the complexities associated with analyzing a three-dimensional problem. A combination of the multiple-seam displacement-discontinuity model and a two-dimensional finite-element window model produces refined results for a specific area of interest by assuming displacement compat-ibility between models. Input to the procedure includes the geometry of mined-out areas in up to two adjacent seams, the rock mass characteris-tics of the surrounding geology, the in situ stress conditions, and the mining sequence. The displacement-discontinuity program calculates ex-pected loadings for mine structures affected by the mining cycle and/or by overlying or underlying seams. Pseudoelastic finite-element analysis using a yield-factor approach determines the stability of coal pillars by simulating the degree and extent of nrogressive rib failure and sub-sequent load transfer. Application of the procedure is demonstrated on a field problem. In-duced stress changes predicted from the numerical model analysis are in reasonably good agreement with stress measurements obtained from an instrumented chain pillar affected by remnant workings in an upper seam.

Jan 1, 1988

Workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., were back on the job December 1, after agreeing to a new 3-year contract. The old contract had expired November 15. On December 20, the Aluminum Company of America reportedly shut down a 42,000-ton-per-year potline at its Wenatchee, Wash., primary aluminum smelter and half of a 23,000-ton-per-year potline at its Vancouver, Wash., smelter as a result of a power cutback by the Bonneville Power Administration. A1 so in December, Kaiser Aluminum & Chemical Corp. reduced overall power at its Mead and Tacoma, Mash,, smelters and shut down one of eight 27,500-ton-per-year potlines at Mead. Reported shutdowns for the firms since September have amounted to 76,000 tons for Alcoa and 50,000 tons for Kaiser. Alcan Aluminum Ltd. announced plans to double the generating capacity at its Kemano hydroelectric power plant in British Columbia to 1,916 megawatts. The additional power would be equal to that required of a primary aluminum smelter with an annual capacity of 567,000 tons.

Jan 1, 1980