Search Documents

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By F. E. Joyce

The Bureau of Mines studied copper-nickel minerals (mainly sulfides) of the Duluth Gabbro Complex in north-eastern Minnesota to determine their response to selective high-temperature sulfatization techniques. The gabbro, containing 0.44 percent copper and 0.13 percent nickel, was ground to minus 325 mesh and sulfatized in a heated, rotating, stainless steel bench-scale retort. Tests demonstrated that over 95 percent of the copper and 80 percent of the nickel can be converted to water-soluble sulfates, depending upon the roasting conditions employed. Yield equations were developed using regression analysis for predicting the extraction of copper and nickel between the temperature limits of 520° to 670° C, the roasting time limits of 3 to 7 hours, and S02 limits of 10 to 40 percent in S02-air mixtures.

Jan 1, 1971

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By Seth T. Reese

THE INJURY DATA and experience at coke ovens in the United States for 1952 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1 to 9: Contain current and comparable data on operating statistics, number and classification of injuries, frequency rates, and accident agencies involved in causing injuries. Data are given for the industry as a whole, for each type of oven, and for the States in which coke is manufactured. (B) Selected injury experience: Tables 10 to 15: Contain comparable injury data in the coking industry covering 5- and 10-year periods on the number of injuries, accident agencies, and severity of injuries. (C) Historic injury experience: Tables 16 to 19: Contain data on the number of injuries, frequency rates, and employment at coke ovens from the earliest records through 1952, Operating statistics from 1929 through 1952 are given in table 19.

Jan 1, 1955

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By H. O. McDonald

Solutions containing Cr6+ and sulfuric acid are used in a number of surface-finishing operations. Substantial quantities of chromium and copper are lost and pollution problems are created when the spent solutions are discarded. To minimize the undesirable environmental effects while improving secondary resource recovery technology, the Bureau of Mines is conducting research to detoxify and recover metals from these solutions. Spent etchants are treated to remove copper and reduce Cr6+ to Cr 3+ in an electrolytic cell. The anodes and cathodes are granulated coke. The spent solution is continuously pumped through the electrodes. Hexavalent chromium is reduced to trivalent chromium, and copper is recovered at the cathode. Reoxidation of Cr3+ at the anode was not observed. The removal and recovery of copper reduction of Cr6+ lessen chemical demand and increase efficiency in waste in treatment operations associated with the use of these solutions.

Jan 1, 1980

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

By M. M. Fine

A laboratory mineral-dressing investigation of manganese ore from the Martin mine, Independence County, Ark., succeeded in recovering ferrograde manganese products. Sintered flotation concentrates analyzing 40.7 and 41.4 percent manganese at overall recoveries of 54.6 and 47.7 percent, respectively, were produced from preconcentrated feed, Preconcentration of the ore for flotation included treatment by magnetic separation and by a combination of magnetic separation and heavy-medium processing. The mineral-dressing study of the Martin mine rhodochrosite ore was part of a general program of the Bureau of Mines to develop domestic sources of strategic minerals, including manganese. Several such potential sources of manganese exist in the Batesville, Ark., district, one of which is represented by the Martin mine. Although the Martin mine area has not been delimited with respect to total reserve tonnage, it is considered to be one of the more important occurrences of manganese in the district. It is estimated that several 100,000 tons of manganese carbonate ore are present in this and similar properties.

Jan 1, 1954

By M. L. Whisman

Radiotracer techniques were developed for stoichiometric studies of photochemical reactions associated with atmospheric smog formation. Stock blends of separate hydrocarbon and oxygenated compounds were prepared and calibrated. 14C-labeled reactants and products in reaction systems involving hydrocarbons and nitrogen oxides at the ppm level were analyzed for qualitative and quantitative data. Precision and accuracy of these methods developed by the Bureau were determined by replication and statistical treatment of data, and these methods are described.

Jan 1, 1969

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By J. V. Batty

Various ores from deposits in the Boulder Dam Recreational Area, Clark County, Nev., were submitted for ore-dressing tests as part of the Bureau of Mines studies of western manganese ores. The Virgin River manganese deposit is situated on the Virgin River arm of Lake Mead, 5 miles from Bonelli's Point, which was formerly the junction of the Virgin and Colorado Rivers. It is 20 miles from Overton, Nev., and 26 miles from Boulder City, Nev. The ore body, composed of wadlike manganese in a tuffaceous gangue, is a flat-lying bed overlain with beds of gypsum and basalt. Two ore samples were submitted by engineers of the Bureau for ore-dressing investigation. Low-grade sample 1 was a composite of channel samples cut from outcrops of the ore body; sample 2, of intermediate manganese grade, was taken from the dump-at the exploratory shaft sunk by the Bureau. The Boulder City manganese deposit is situated in the Boulder Dam Recreational Area -3 miles southwest of Boulder City. The ore body is a manganiferous gypsum bed 32 feet thick, slightly inclined from the horizontal. The ore sample submitted-by engineers of the Bureau for-testing was taken from channel cuts in the walls of the shaft, which cuts through the bed vertically.

Jan 1, 1948

By Martin H. Stanczyk

The Bureau of Mines studied continuous closed-circuit attrition grinding of a coarse commercial filler-grade kaolin to produce paper-coating-grade clay having a particle size analysis of at least 70 percent minus 2-micron equivalent spherical diameter (esd). The coarse clay, containing about 12 percent minus 2-micron-esd material, was ground in a Bureau-developed 10-inch-diameter attrition grinder in closed circuit with a 5-foot-diameter bowl classifier. In the best test, a finished product containing 82.7 percent minus 2-micron-esd material was obtained when grinding 20 pounds of raw clay per hour at percent solids with a 100-percent circulating load. Energy consumption was about 341 kilowatt-hours per ton of clay feed, or 487 kilowatt-hours per ton of minus 2-micron-esd material produced. Closed-circuit grinding gave some-what greater particle size reduction and lower energy consumption than either batch or continuous open-circuit grinding.

Jan 1, 1965

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,938,200 for the 1.03-million-ton-per-year (MJ.Vl tpy) mine to $31,435,500 for the 3.09 MM tpy mine. Total capital investment ranges from $21,607,200 to $51,982,000 for the same mines. Corresponding selling prices for the coal range from $9.11 to $8.06 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By F. Garcia, J. Cervik

Recent advances in the commercial separation of gases using membranes have renewed interest in the possibility of applying this technology to the recovery of methane ( CH4 ) from mining operations . This Bureau of Mines report briefly reviews the history of the development of membranes for gas separation , the theory of how they work , and their application to the separation of methane from air and associated problems . However , methane -air mixtures are difficult to separate with membranes because the pertinent gas couples , 02 - N2 , 02 - CH4 , and N2 -CH4 , have poor separation characteristics , as indicated by their separation factors of about 3 or less . Even if these separation factors were substantially higher , there is doubt that methane could be recovered economically from the low concentrations in mine ventilation exhaust ( 2 vol pct or less ) . The exhaust pressures are not sufficient for adequate separation . The power cost of compressing the methane recovered . these mixtures would far exceed the value of New discoveries could make separation of gob hole methane - air mixtures practical . These mixtures have much higher concentrations of methane (from 30 to 100 vol pct ) ; however , for safety reasons , be limited to gob gas with 60 vol pct CH4 or more .

Jan 1, 1988

By John C. Edwards

A computer code for laminar, steady-state, incompressible, two-dimensional flow developed by Gosman (2)3 was modified by the Bureau of Mines to calculate shock (minor) loss at the intersections of ventilation ducts. Turbulent flow was simulated using laminar flow equations and an appropriate wall shear stress. Results of the calculation showed good agreement with the experiment.

Jan 1, 1977

By Hillary W. St. Clair

Mining activity began in colonial times with ironmaking operations scattered along the eastern seaboard. Iron furnaces and forges manufactured iron implements from bog iron ores using charcoal from the extensive forests as a fuel. Lead ores were mined in the Mississippi Valley and copper ores in the Lake Superior region. However, the real beginning of the American mining industry did not occur until the 19th century. The history of American mining is organized around three epochal events. The first was the discovery of gold in California in 1848, which marked the beginning of a period of apprenticeship in mining and metallurgical techniques. The second was the discovery of the fabulous Comstock Lode in western Nevada in 1859, which expanded mining throughout the Far West and led to large-scale underground mining and the development of smelting techniques for lead, silver, and copper ores. The third event was the building of a transcontinental rail-road system after the Civil War, which brought about the consolidation of the industry from a large number of independent mines, mills, and smelters into integrated operations run by large corporations. Thus developed the mining industry that today supplies the energy and critical materials for the great-est industrial complex the world has known.

Jan 1, 1977

By Mark Sheppard

This paper is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different tries of primary crushers; and ( 4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of tine fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By J. W. Chester

The rapid depletion of zinc-lead ore reserves and the rising costs of exploration have been major factors in the decline of mining activities and explorations for additional reserves in the Tri-State mining district. There is a need to develop new or adopt known, improved exploration techniques that will appreciably lower the costs of exploration. Demonstration of the practicability of using improved techniques to indicate, rapidly and cheaply, mineralized areas or geologic structures where more intensive explorations are justified could stimulate the search for and discovery of additional ore reserves. Various operators in the Tri-State district have used geophysical surveys to some extent since 1928 to guide exploratory drilling. Some geophysical investigations have also been made in the district by the State Geological Surveys of Kansas (11)3/ and Missouri (8, 13) and by Federal agencies (16), with the objective of directing exploratory drilling to areas where geologic conditions favored ore deposition. Many factual data obtained have not been published. The investigations generally have not been broad enough to permit conclusive evaluation of the usefulness of the geophysical techniques in all parts of the district.

Jan 1, 1959