Search Documents

By W. M. Dressel

A simple, reliable field test for beryllium in rocks has been developed by the Rolla Metallurgy Research Center of the Federal Bureau of Minas. A small portion of the pulverized rock is fused with a sodium carbonate-sodium hydroxide flux in a wire loop. The fused mass is dissolved in water, a few drops of quinizarin solution are added, and the solution is viewed under ultraviolet light. A pink-to-orange fluorescence reveals the presence of beryllium in a sample containing as little as 0.013 percent beryllium (0.26 percent beryl). INTRODUCTION New and potential uses for beryllium make necessary a more intensive search for this metal, which is so similar to aluminum in its chemical reactions that it is not separated from aluminum in ordinary chemical analyses. The principal ore mineral of beryllium is beryl, a beryllium-aluminum silicate, which contains only 5 percent beryllium. This mineral is so similar to quartz in appearance that it is not always possible to distinguish one from the other in the field. While the distinction may be made easily with a petrographic microscope, few prospectors have access to such an instrument, and fewer still know how to use it.

Jan 1, 1960

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult, longstanding engineering problems associated with coal mining is the catastrophic failure of cog mine structures known as bumps. For more than 70 years, researchers and practitioners have assembled a wealth of technical information on coal bumps in an attempt to understand and control them. However, many technical issues raised long ago are still being debated today. This paper examines past experiences and recognizes achievements in the realm of coal bumps. U.S. Bureau of Mines (USBM) researchers collected and analyzed 172 coal bump incident reports and compiled the pertinent statistics into a database. Actual field studied are also discussed. Examination of past experience has shown that there is no one set of defining characteristics that is responsible for coal bumps. In all cases, bumps occur when complex arrangements of geology, stress, and mining conditions interact to interfere with the orderly dissipation of stress. However, it is evident from the database that a tremendous reservoir of knowledge has been established from past experience that has unquestionably limited the severity of coal mine bumps in the United States.

By R. Vernon Helm

Four tables listing values for the various physical properties of those sulfur compounds most likely to occur in petroleum and petroleum products are given herein. The data necessary to bring the first compilation2/ in this subject up to date are given in table I -Revised and Additional Data, which includes boiling points, refractive indices, densities, and freezing points. Tables 11-, III, and IV are published for the first time and include refractive indices for the F, C, and G' lines of hydrogen and the helium D:3 line; surface tensions and viscosities, and refractivity intercepts, specific dispersions, specific refractions, and parachors. The need for information concerning the sulfur compounds in petroleum is becoming-more urgent because of the necessity of refining larger quantities of high-sulfur crude oil to meet the rising demand for petroleum products. For a number of years the Bureau of Mines has been engaged in research to make available more information concerning the properties of the sulfur compounds in petroleum. The petroleum industry has recognized the value of such studies, and as a result the American Petroleum Institute has established Research Project 48A to study sulfur compounds. The investigations under this Project are to be done in Bureau of Mines laboratories as a cooperative project in connection with the work already started.

Jan 1, 1949

By Ivette E. Torres

The final 26 tables of this chapter, tables 24-49, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Mainly because of the separation of the countries that formed the U.S.S.R., the column that provided a 5-year average, was deleted. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1992. This group of tables now includes each of the top 19 crude minerals in 1983 in terms of value of their output plus 3 others of lesser rank. These 22 crude mineral commodities accounted for more than 98 % of the estimated value of world crude mineral production in 1983. Coal production, included in the 1983 value of production table as two separated entries, is combined in one table in this chapter. World output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1994

By C. W. Smith

The U.S. Bureau of Mines; Tuscaloosa Research Center, in cooperation with the U.S. Army Corps of Engineers under interagency Agreement No. 14-09-0078-1510, conducted a comprehensive sampling program of 10 upland disposal sites along the Alabama, Black Warrior, and Tombigbee River systems in Alabama. Samples from each site were characterized according to particle size, chemical analysis, mineralogical content, and potential end use. Additionally, samples were subjected to the Toxic Characteristic Leachate Procedure to determine the presence of potentially harmful heavy metals. Based on the results of these studies, each sample was determined to have properties amenable for use as aggregate in general-purpose portland cement concretes and certain asphalt concrete applications.

Jan 1, 2010

By D. J. Stoops, H. Kato, M. D. Carver

The effects of impurity elements silicon , aluminum, copper , nitrogen , and manganese , at 50 to 300 ppm, on properties of the zirconium alloy Zircaloy 2 were investigated . Variations in microstructure , mechanical properties , and corrosion behavior in some inorganic acid and salt solutions were observed with variations in level of impurity element . Corrodents were solutions of sulfuric acid , phosphoric acid , copper chloride , and iron chloride . Silicon was found to modify annealed microstructures by spheroidizing and dispersion of secondphase material throughout grains . Silicon or manganese improved ultimate and yield strength of the alloy without loss in ductility . All five elements affected corrosion rates of the alloy , the effect being generally different for each element .

Jan 1, 1964

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By R. V. Ramani, R. Bhaskar

"The results .of an experimental and theoretical research study into the spatial and .temporal behavior of dust in mine airways is summarized in the paper. Experiments were performed in mine airways under both controlled and .normal operating conditions. The controlled experiments included the documentation of the concentration and deposition patterns for two types of dust under three different velocities. Real-time dust concentration data were obtained using Real-time Aerosol Monitors (RAM-1) to determine the dispersion coefficient in a mine airway. On the theoretical front, a convection diffusion model of the dust flow phenomenon in mine airways was developed considering dominant mechanisms affecting dust transport and deposition in mine airways. Mechanisms modeled include turbulent and gravitational deposition, coagulation, and dispersion.In this paper, comparative analyses of results of the controlled experiments with the predictions of the mathematical model are presented. In addition to the overall validity, the adequacy of the individual components of the model, such as deposition in the total and respirable range, and dispersion are examined in light of the experimental observations.The experimental data from controlled experiments compared more favorably with model predicted results for similar conditions as opposed to the ·comparative analysis results for in-mine experiments. Specifically, the model· predictions for an 800-meter stretch of a mine airway reveal some significant differences from the behavior noticed in the mine. The deposition was lower than that predicted by the model. Consequently, concentrations were higher than those predicted by the model. The implications of these and other findings for further investigations are discussed in the paper."

Aug 31, 1989

By B. T. Brady

Laboratory measurements by the Bureau of Mines indicate that failure in dry rock specimens measuring approximately 13 cm in length is preceded by tilt anomalies lasting a few milliseconds. The tilt behavior is qualitatively similar to that reported to precede earthquakes. Test results suggest that the time duration of this tilt anomaly for laboratory specimens of this length is independent of rock type, in agreement with theoretical predictions and other experimental data on rock failures including earthquakes.

Jan 1, 1975

By Wesley T. Holmes

In this final stage of a three-part investigation of the smelting of titania-bearing iron materials, the Bureau of Mines conducted semicontinuous smelting tests in a laboratory electric arc furnace on four concentrates and one are. The objective was to substantiate the significance of liquidus temperature measurements in predicting satisfactory slag compositions in electric furnace smelting of titaniferous magnetites to produce pig iron. Previously obtained liquidus temperature data were used in determining flux requirements. Self-fluxing pellets of either ore or concentrate plus fluxes and reductants were made to produce pig iron and slags containing 0.2 to 0.6 percent titanium. Individual constituents of the slags generally agreed within 5 percent with the value of the corresponding constituent of target composition. Liquidus temperature of furnace slags generally agreed within 50° C of the value obtained from corresponding nominal synthetic slag. The results of the three phases of the investigation may serve as guide-lines for determining flux requirements in smelting a wide variety of titaniferous magnetites and other titania and iron-bearing materials.

Jan 1, 1969

By T. A. Klinefelter

"INTRODUCTION During the development work on sponge iron by the Bureau of lines it was desired to produce a product of maximum density for the furnace. One means of doing this would be to make a plastic mixture of the ground ore and extrude as pellets or large slugs or brick shapes.If a pelletizing Process is employed, the pellets must be strong enough to resist breaking when rolled and tumbled in going through the rotary kiln. If a brick-making process is employed, the brick must be strong enough to withstand handling and considerable pressure when stacked in the kilns.The study had two objectives: first, to find a binder of sufficient strength throughout the early stages of curing and heat treating and, second, to determine the degree of curing and heat treatment necessary to prevent disintegration under normal working conditions.Although the investigation had as its primary objective the processing of sponge iron, the data should interest other industries in which non plastic or poor-bonding slimes are a problem."

Jan 1, 1946

By John C. Machisak

THIS INFORMATION CIRCULAR contains 1956 and 1957 injury experience and employment data for metal mines in the United States and Alaska. Unlike previous publications, this report covers only metal mining and contains statistical data on injuries and employment pertinent to metal mines and mills reporting voluntarily to the Bureau of Mines on an annual basis. Injury and employment data for the nonmetal industries, which from 1911 through 1955 were published in the same series as the metal industries, for the first time will be published separately as an information circular entitled "Injury Experience in the Nonmetal Industries, 1956 and 1957." The Bureau of Mines is authorized to make requests for injury and employment data, and the information submitted by operators of metal mines and mills is a step forward in promoting safety in the metal-mining industry. Every effort has been made to make this coverage as complete as possible.

Jan 1, 1960

By W. W. Adams, T. D. Lawrence, D. R. White

"This paper presents the results of the eleventh yearly accident-prevention contest, the National Safety Competition of 1935, conducted by the United States Bureau of Mines. Participating in the competition were 336 mines and Quarries in 37 States. Five mining or quarrying companies, each the leader in its group for having established the best safety record during the year, were awarded the national safety trophies 'Sentinels of Safety.Since these annual contests were begun 11 years ago the scope of the competition has been broadened materially, both as to the number of plants participating and as to the number of man-hours of exposure to accident hazards. Moreover, marked progress in the pre¬vention of accidents has been achieved, as is indicated by an almost constant downward course in the accident-frequency rates for the contest group as a whole during the past 11 years. On the other hand, the accident-severity rates for the group showed an upward trend during the first part of the period and a downward trend during the latter part, except in 1930 and 1934, when two disastrous explosions occurred with heavy loss of life, and in 1935, when there was an increase in the number of fatalities although no major disasters occurred. The accident rate for 1935, both as to frequency and severity, was higher than for 1934.The National Safety Competition is conducted by the Bureau of Mines in the interest of safety in the mining and quarrying industries. This object is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive well-merited and national recognition for their achievement. Indirectly the purpose of the contest is accomplished through studies by the Bureau of Mines of the fasts contained in the accident reports which the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics that constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting from industrial accidents."

Jul 1, 1936

By T. E. Bernard

The CO2-absorbent canisters used in four approved rescue breathing apparatus were investigated. A breathing machine was used to simulate human expiration with gas flow rates of 26, 37, and 48 1/min of 3.5% CO2 in air. The exit gas CO2 concentration, the pressure drop across the canister, and the exit-gas temperature were monitored. The absorbent capacities of the packed-bed canister designs were found to be dependent on flow rate within the range studied, while the capacities of the other designs were less affected. The radial canister had the least resistance to breathing while the complex bed design proved to be the most effective in utilization of the chemical. The overall results indicated that LiOH (lithium hydroxide) has the highest capacity for CO2 absorption among the absorbents tested. It can be used in a simple packed-bed design while maintaining acceptable levels of resistance and exit-gas temperature. Examination of oxygen supply with respect to CO2-absorption capacity suggested that it is desirable to closely match CO2-absorption capacity with the avail-able O2 supply to minimize the size and weight of rescue breathing apparatus.

Jan 1, 1979

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By Wm. W. Odell

In distributing natural and mixed gas, the industry is each year confronted with the problem of manufacturing gas in increasing amounts as the supply of natural gas becomes more nearly exhausted. The manufactured gas is now used in mixtures with the still available natural product, and will subsequently be used straight as a substitute gas. The gases that might be considered, and are producible by tried and developed processes, include water gas, carbureted water gas, and coal gas. Singularly, these gases can be used in this manner in ordinary appliances only when proportional amounts of them in the mixtures do not vary beyond rather definite limits, unless burner adjustments are made. The limits are defined by the specific gravity, content of inerts, and burning properties of the respective gases. Anticipating a future standard for city gas lower than that of natural gas during the period when considerable natural gas is available, there is justification for considering the possibility of re-forming natural gas and making a product that has substantially the same properties as other gases which can readily be generated. This report gives the results obtained during a series of tests made under a cooperative agreement by the U. S. Bureau of Mines with the Ohio Fuel Gas Co., re-forming natural gas at Toledo, Ohio, in full-scale operation in a water-gas generator having a grate area of 25.1 square feet. ACKNOWLEDGMENTS The Ohio Fuel Gas Co. constructed a special water-gas generator for the tests and provided men and the necessary funds for its operation. Appreciation is expressed for the general spirit of helpful cooperation which was evidenced in the activities of all those who took part in the work. Particular acknowledgment is made of the assistance rendered by C. W. Wallace, manager, and by C. F. Cramer, superintendent, and A. Upp, foreman of the plant.

Jan 1, 1929

By D. N. Nilsen

A mathematical modeling method was developed by the Bureau of Mines for the prediction of the principal equilibrium species in the solvent extraction of copper. The use of models for predicting the amount of metal extracted can reduce the amount of experimental work required to characterize a system for purposes such as optimization studies. Models were developed for the extraction of copper from ammoniacal sulfate and carbonate solutions with commercially available extract ants commonly used by industry. Results from laboratory shakeout tests compared well with predictions of the equilibrium concentrations of copper and pH values. For example, the loading of copper onto the solvent was predicted for most cases within ±S pct of the measured values, and the pH to with-in ±O.l pH unit in sulfate systems and ±O.2 pH unit in carbonate systems. Both mechanistic and empirical extraction equations were developed from laboratory data for copper and ammonia. The empirical-based models were slightly more accurate than were the mechanistic-based mod-els. Industrial level concentrations of the aqueous and organic constituents were used in this work. Independent variables included copper concentration, ionic strength, and initial pH of the aqueous phase; extractants, diluents, and their concentration in the organic phase; and temperature.

Jan 1, 1988