Search Documents

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By Paul M. Tyler

The value of mica depends chiefly upon the size of the flat sheets into which it can be split and also upon whether it is clear or stained. Muscovite (white mica) and philogopite (amber mica) are the micas of commerce. Biotite (black mica) and other varieties are virtually unsalable. Vermiculite, an altered mica having the extraordinary property of expanding greatly when heated, preferably should not be classed commercially as mica. Mica is marketed as (1) cut or uncut block, (2) sheet, (3) splittings, and (4) wet or dry ground mica. In the United States, mica that will not yield flat films over about 1-1/2 inches square, or that is ruled, rumpled, or flawed in any way, can be sold only as scrap, its sole use being for making ground mica. Only sizes that will yield rectangles 1-1/2 by 2 inches or larger can be classed as sheet quality; slightly smaller sizes may be classed as punch, and under certain circumstances still smaller sizes, down to about 1 inch square, may be used for splittings, which are mostly a thousandth of an inch thick or even thinner. Splittings, however, are produced in large quantities only in British India, where labor costs very little. Even there the work is done mostly by children, who not only work cheaper but have a delicacy of touch that enables them to do the splitting faster and better. No mechanical process yet devised will permit ordinary splittings to be made economically in the United States.

Jan 1, 1938

By A. C. Richardson, G. D. Coe, B. M. Bird

"The Hull mine of the De'Bardeleben Coal Corporation is located in the Warrior field, in Walker County, Ala., about 25 miles northwest of Birmingham. The Mary Lee bed at this point is coking coal and has been used in the manufacture of by-product coke, but at present it is sold exclusively as a domestic and locomotive fuel.The data in this paper, which is the third in a series on the washability of Alabama coals,5 have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. The paper contains screen-sizing and float-and.-sink tests of a representative sample of run-of-mine coal, and flakiness tests and crushing tests of certain sizes.In addition, complete analyses of the ¾-inch to 3/16-inch size, raw coal, together with ash fusibility tests of the float-and-sink fractions have been made; those results are given in Tables 1 and 2. Since they indicate that the pr ration problem, like that at Lewisburg, Ala., is one of ash reduction, the further tests and the discussion have been restricted to that subject."

Apr 1, 1931

By M. E. Tyrrell

Despits its high melting point (2,135° C.), resistance to attack by molten metals, and its hardness (8), spinel (MgO?Al203) synthesized by the fusion of alumina (Al 2 0.) and magnesia (MgO) is not used on a large scale as a commercial furnace lining, mainly because of the prohibitive cost. This investigation by the Federal Bureau of Mines was prompted by the possibility of producing synthetic spinel from inexpensive raw materials by methods outlined in U.S. Patent 2,029,773, "Process for Obtaining Products Containing Spinets," dated February 4, 1936. In this patent Ture B. Haglund described a process for recovering crystalline spinels from melts in the system Mg0?Al203-2CaO-SiO2, a system well suited to the use of starting materials such as dolomite CaMg(C03)2, olivine [2(Mg?Fe)0.Si02], and bauxite (Al203?2H20) which are abundant in the southeastern United States. Compositions, ranging from a low content in the eutectic mixture of 35 percent spinal and 65 percent dicalcium silicate (2 CaO?SiO2) to a high of 75 percent spinel and 25 percent dicalcium silicate, were fused in electric furnaces of the arc-resistance and internal-resistance types. So long as members of the system were in proper chemical balance, "dusting" slags could be produced over the entire range of spinel concentration.

Jan 1, 1961

By R. L. Loofbourow

The adjacent towns of Rouyn and Noranda, centers of the Rouyn mining district of western Quebec, are 360 miles by air line almost duo north of Toronto. Rouyn is reached from the main lines of the Canadian National Railways and the Canadian Pacific Railway at North Bay, Ontario, by the Temiskaming & Northern Ontario Railway and its subsidiary, the Nipissing Central Railway. Noranda is the southwestern terminus of a branch from the Canadian National Railway between Winnipeg and Quebec. The Rouyn mining district is a part of a mineralized zone that has been traced for a distance of 140 miles from Kirkland Lake in Ontario eastward into the Province of Quebec to the Pascalis district. From Rouyn the mine is 5 miler almost duo south over a gravel rend built by the company with assistance from the Province of Quebec.

Jan 1, 1933

By Walter Pajalich

This Bureau of Mines report is a study of the organizational framework of the ferrous scrap industry, of the products produced, and of the factors affecting the consumption of ferrous scrap by the steel industry. Consumption data from 27 major iron and steel firms in the States of Illinois, Indiana, Iowa, Michigan, Minnesota, and Wisconsin during the period between 1957 to 1962 were grouped by type of iron and steel furnace production facilities to determine consumption pattern for various grades of scrap in comparison to ingot production, hot metal consumption, and home scrap generation. Grades of scrap affected by changes in scrap consumption were determined, and the pattern that emerged was analyzed. Correlation of scrap demand and its effects on scrap prices based on price of scrap receipts of No. 1 heavy melting scrap and No. 2 bundles in the Chicago area for the years 1957 through 1962 indicated that demand trends do not always affect the price of scrap, Past and present technological advancements in steelmaking processes are discussed, and their effects on the scrap industry are analyzed.

Jan 1, 1967

By F. K. McIntosh, A. F. Robertson, T. J. Ballard

"INTRODUCTION Molybdenum deposits occur in Halifax County, N. C., near the eastern border of the Piedmont province. The deposits are associated with a small granite body about 2 miles long and half a mile wide. Molybdenite is the principal ore mineral and is found as disseminations or thin stringers in quartz veins and occasionally in the enclosing granite or schist wall rock.The deposits were investigated by Almon F. Robertson and Charles J. Cohen, engineers of the Bureau of Mines, in 1942 and 1943, who recommended that the deposits be explored to supplement reserves of critical war minerals.The Bureau made the initial exploration of the deposits in July 1943 and continued its work to January 1944. Drilling was resumed from July to December 1946 to test the deposits at &eater depth than had been attempted during the previous exploration."

Dec 1, 1947

By D. L. Forrester

This paper, describing the milling practice of the Old Dominion Co., is one of a series being prepared by the: United Staten Bureau of Mines. ACKNOWLEDGMENT In the preparation f this paper, acknowledgment is made of the valuable service rendered by R. S. Allen, metallurgist of the Old Dominion Co. T. G. Chapman, one f the consulting engineers of the Bureau of Mines, assisted in arranging the paper for publication.

Jan 1, 1931

By Seth C. Scharfer

"As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the Gibbs energies of formation of MoS2 (molybdenite) and WS2 (tungsten disulfide) were determined with high-temperature galvanic cells employing stabilized Zr02 (zirconia) as the electro¬lyte. In the temperature range from 867 to 1,209 K, potential measurements were obtained for the cellPt, MoS2 , Mo02 , SO2 = 1 atm // Zr02 // 02 = 0.0112 atm, Pt, with the overall cell reactionMoS2(c) + 3 02(g, 0.0112 atm) = Mo02 (c) + 2 S02(g). (1)These results, combined with the best available values for Gibbs energies of formation (?G°f) of Mo02 (molybdenum dioxide) and SO2 (sulfur dioxide) from the literature, give the standard Gibbs energy of formation of MoS2, ?G°f, for the reactionMo(c) + S2(g) = MoS2(c) (2)?G°f = -96.681 + 43.76 x 10-3T±0.538 kcal/mole, (3)where temperature (T) is expressed in Kelvins.Similar measurements in the temperature range from 872 to 1,210 K were obtained for the cellPt, WS2 , W03 , SO2 = 1 atm // Zr02 // 02 = 0.0114 atm, Pt, with the overall cell reactionWS2(c) + 3.5 02(g, 0.0114 atm) = W03 (c)+ 2 S02(g). (4) Combination of these results with the best available data of ?G°f for W03 (tungsten trioxide) and SO2 from the literature gives the Gibbs energy of formation of WS2 in the temperature range from 872 to 1,210 K for the reactionW(c) + S2(g) = WS2 (c)(5)?G°f = -92.429 + 43.88 x 10-3T ± 0.280 kcal/mole. (6)A third-law analysis yields a standard enthalpy (?H°f) for the reaction298Mo(c) + 2 S(rh) = MoS2(c), (7)?H°f = -67.36±0.60 kcal/mole, (8)298where the standard states are pure crystalline MoS2 / and rhombic sulfur."

Jan 1, 1980

By J. E. Pahlman

As part of its effort to reduce the need for strategic minerals through conservation and to reduce the capital and energy requirements of mineral processing, the Bureau of Mines has investigated a method for preparing ferrochromium alloys containing less than 2 percent carbon. This method will conserve chromium and should reduce the capital and energy requirements for chromite reduction. Reduced products containing less than 2 wt-pct C and as low as 0.01 wt-pct C were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 torr and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be supe¬rior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates (Fe,Cr)7C3 and (Fe,Cr)23C6, No evidence of carbide intermediates Fe3C or Cr3C2 was found. Buttons of ferrochrome alloys were made by melting a mixture of reduced products with CaO and Si02 at 1,700° C for 20 minutes in an induction furnace,

Jan 1, 1980

By Cleo Griffith Rall, D. B. Taliaferro

The method for determining oil and water saturations described herein has been used successfully for several years in the core laboratories of the Bureau of Mines. The apparatus constructed according to the original specifications has proved very satisfactory; in fact, it has been widely adopted by core laboratories throughout the petroleum industry. The writers have found that the method gives reproducible results, the degree of accuracy depending largely on the attention to details given by the operator. The relative importance of these details of procedure and the design of the apparatus are discussed in this report. In September 1940, the Bureau of Mines published a report describing a method used in its laboratories for the determination of the water content of oil-field cores. The procedure was essentially the same as that adopted by the American Society for Testing Materials for the determination of the water content of petroleum products, although the apparatus and technique were altered slightly to increase the precision of the method and to adapt it to the characteristics of the material to be tested. The report also contained a description of the method used at that time in the Bureau’s core laboratories for measuring the oil content of a core, utilizing the sample on which the water-saturation determination had been made. The procedure involved the transfer of the weighed sample, from which the water had been distilled and measured, to a Soxhlet extractor and the removal of the remaining oil by means of a suitable solvent. Soon after the report was published, the water-determination apparatus described therein was modified so that both the oil and water contents of a core sample could be determined simultaneously. This method, which has been described by Yuster, is now widely used throughout the industry.

Dec 1, 1946

By D. W. Richardson

This Bureau of Mines publication provides the enthalpy of formation of malachite [Cua(COs)(OH)2] as determined by hydrochloric acid solution calorimetry. At 298.15 K the enthalpy of formation from the component oxides is -15.l0±0.30 kcal/mole and from the elements, -251.9±0.5 kcal/mole.

Jan 1, 1974

By A. Visnapuu

The Bureau of Mines has upgraded high-iron domestic chromite concentrates by a carbonyl process. The upgraded chromite concentrates show as much as 10 wt pct higher Cr203 content and up to a threefold in-crease in the Cr:Fe ratio, compared with the starting concentrates. The high-iron chromites were first reduced to convert the iron oxides to the metal, and then treated with CO at elevated pressures and low temperatures to convert part of the metallic iron fraction to iron pentacarbonyl. Carbonylation was accelerated by the addition of H2S in small quantities. The iron pentacarbonyl was extricated from the con-centrate in the pressure reactor during carbonylation by a CO sweep through a pressure-reducing valve and passed through a decomposer at atmospheric pressure to convert it back to iron metal and CO. CO pres-sure, temperature, promoter trends, and other factors enhancing iron pentacarbonyl formation are presented.

Jan 1, 1985

By Harry R. Johnson

Domestic expenditures by the U.S. petroleum industry have exhibited distinctive shifts in emphasis over the past 20 years. From the end of World War II to 1955, expenditures for all phases of the industry expanded. Although over one-half of all expenditures were for production, the relative emphasis was changed after 1956-58 from production toward processing and marketing. The period 1967-69 marked the beginning of a return to emphasis on exploration and production. These trends in expenditure patterns are logical and rational when related to domestic and international economic conditions and to the widespread application of improved production technology. As the immense job of developing the oil resources of Alaska and other regions begins, the petroleum industry will continue to turn to external sources for working capital. Long-term debt will probably be the principal method of external financing through 1970, but a definite shift toward new common and preferred stocks will be made. Higher product prices may be sought by the petroleum industry, but the economics of crude-oil production, changes in the tax structure, and possible changes in the oil imports control program make the price structure of crude oil and crude-oil products unpredictable at the present time.

Jan 1, 1970

By Ernest F. Burchard, J. R. Thoenen

"INTRODUCTION Technically speaking, bauxite is not a definite mineral but a mixture of several minerals belonging to a group of partly consolidated material known as laterite, which have been formed by surface weathering of rocks.The term bauxite is applied to the ore of aluminum, although a substantial amount is used for other purposes, such as a base in certain chemical industries and in the manufacture of artificial abrasives, refractories, and certain cements. Although bauxite has not been classed as strategic it now appears that the domestic supply may be insufficient for expanded defense requirements.Until recently, domestic production of metallic aluminum has been ample to meet requirements, but estimates of pyramiding future needs of the defense program have caused serious attention to be directed to the self-sufficiency of this country, both as to the supply of the raw material, bauxite, and the metallurgical capacity available to convert the ore to metallic aluminum.At the request of the Secretary of the interior, representatives of the Bureau of Mines and the Geological Survey recently investigated domestic resources of bauxite.A preliminary study of published literature and a field investigation disclosed that"

Nov 1, 1941

By Adrian J. Mathias

This report presents the results of an investigation of a mine production-scheduling model and a critical path analysis for long-range mine planning. An example is given to illustrate how these techniques might be used to plan long-range development and production scheduling for a large underground mine. The model, based on estimated ore block grades and tonnages, and on designed mine development layout, simulates mining of ore blocks in a sequence necessary to fulfill mill requirements for ore tonnage and grade evaluation within pre-established system restrictions. Simulated production schedules are obtained as output from the model. These production schedules are then incorporated into a critical path analysis to determine the sequence for the long-range development work so as to fulfill the production schedules and thereby meet the ore grade and tonnage requirements of the mill.

Jan 1, 1967

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been published5/ describing apparatus and tests made on anthracite to determine the amount and composition of the a oxidation products when normal dry air was passed through it at temperatures varrying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative proportions varied with the temperature. From these results, graphs were prepared by which the temperature at which the coal was oxidized could be estimated thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By G. S. Scott

[In the course of the investigation the Bureau of Mines is carrying on to determine the causes, behavior, and control of mine fires, the detection of incipient heating underground in the mines and above ground in refuse banks has received consideration. A report has been puplished5/ describing apparatus and tests made on anthracite to determining the amount and composition of the oxidation products when normal dry air was passed through it at temperatures varying from 100° to 350° C. These tests showed that the amount of evolved gases and their relative prorortions varied with the temperature. From: these results, graphs were prepared by which `he temperature at which the coal was oxidized could 'be estimated, thus giving a possible means of detecting incipient heating.]

Jan 1, 1938

By G. M. Kintz, E. H. Denny

Although some engineering colleges recognize the importance of instructing young engineers in industrial safety , the different institutions handle this instruction in various ways . It is believed that a recent industrial safety course , conducted at the Colorado School of Mines through the cooperation of this school and the Bureau of Mines , U. S. Department of Commerce , presents some unusual features that are of interest to other schools and to the mining public .

Sep 1, 1930