Search Documents

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Jr. Frost

Helium used as a tracer gas in petroleum reservoirs continues to show great promise as a new tool for the oil and gas industry, according to tests conducted jointly by the Bureau of Nines and The Pure Oil Co. in-the Cabin Creek field, Boone and Kanawha Counties, W. Va. Helium, when used as a, tracer gas, is mixed with natural gas being injected into a reservoir for secondary recovery of oil, recycling, pressure-maintenance, or other purposes. Three separate experimental helium tracer-gas tests were run in the Cabin Creek, W. Va., field, wherein helium was added as a tracer to the natural gas that was being injected into the oil-bearing Berea sandstone. The results obtained in each test permitted determining the direction and rate of travel of the injected gas, calculating the volume of injected gas in the gas produced at the various wells, and determining the nature of the transition from natural gas to injected gas during a gas-injection program. Data were obtained on the effects obtained from waves of injected gab containing 1 percent and containing 5 percent helium and from a wave of essentially pure helium injected into the formation.

Jan 1, 1950

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

By J. W. Adams

This report surveys the efforts of six contractors to the U.S. Bureau of Mines with regard to their electromagnetic noise measurement programs. What has been done, what is planned, and evaluations and recommendations are given for each contractor. The main observation is that to date there is not sufficient knowledge of electromagnetic interference in mine environments to design a reliable communication system. This knowledge should be available by the end of June 1972 if certain planned programs are completed successfully. A major effort of this report is to establish parameters to be measured, units to be used, and workable formats for data presentation. This is given in Appendix A. Some details concerning equipment, procedures, locations, and sample data are included in Appendix B.

Jan 1, 1971

By F. A. Rutledge

"The chromite deposits of Red Mountain, 10,miles southeast of Seldovia, Alaska, are in an intrusive of ultramafic rocks. The earliest reference to the deposits was made by U.S. Grant3/; J.B. Mertic, Jr. 4/ made a brief examination in 1917; and A.C. Gill5/ spent 7 weeks studying the ore bodies and geology of the region in 1918. The Federal Geological Survey had a field party in the region from July until September 1940 and the Red Mountain area was mapped and geological data were assembled by P.W. Guild.6/A preliminary investigation of the Kenai chromite deposits was made in July 1941 by R. S. Sanford,7/district engineer of the Bureau of Mines, accompanied by P. W. Guild, assistant geologist of the Geologi¬cal Survey. This was followed by surface sampling and core drilling, which were completed in September 1942 under the direction of John W. Cole,8 associate engineer of the Bureau of Mines. G. O. Gates, associate geologist, and A, B. Unkelsbay, junior geologist, of the Geological Survey, logged cores and interpreted geologic features revealed by Bureau of Mines drilling and trenching.9/J. C. Roehm, associate engineer of the Territorial Department of Mines; examined the Red Mountain area in august 1941.10/Additional exploration of other deposits in. the Red Mountain area was completed during the summer of 194. Work consisted of surface sampling, core drilling, and mapping. G. O. Gates, associate geologist of the Geological Survey, spent 4 days in August investigating results of the Bureau of Mines program.Throughout the exploratory work conducted by the Bureau of Mines the cooperation of Red Mountain Chromite, Inc., and especially of John Blodgett, Jr., and Collis 2, Druley, president and superintendent, respectively, was greatly appreciated. Use of their camp in the Windy River cirque and shops at Kasitsna Bay facilitated the Bureau of Mines program."

Apr 1, 1946

By A. E. Kehew

Earth resistivity surveys using the Wenner electrode configuration were made in unmined areas and reclaimed spoils at three surface lignite mines in western North Dakota. The study sites were the Center, Indian Head, and Falkirk Mines. Automatic interpretation of the curves was accomplished with the method of Zohdy and Bisdorf (1975). Overburden materials become more homogeneous with respect to resistivity during the mining and reclamation process. The spoils curves show localized hetero-geneities probably related to discontinuous moisture content variations in the spoils. Consistent resistivity differences in spoils occur between mines with over-burdens of different mineralogic compositions. Groundwater chemical composition in terms of total-dissolved-solids (TDS) is inversely correlated (r=-0.61) with apparent resistivity at the 80-foot spacing from a survey centered at a piezometer screened near the base of the spoils. Better inverse correlation is probably pre-vented by high variability in TDS within the spoils groundwater. A useful predictive relationship may be the plot of mean apparent resistivity at the 80-foot spacing for ar. entire mine against mean TDS for all wells in spoils at that mine. Data from more mines are needed to test the hypothesis.

Jan 1, 1982

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By D. Harrington

Approximately 6,000 coal mines are operated in the United States. All of them have in some degree the elements that are likely to contribute to an explosion, hence it is surprising that explosion disasters are not more frequent and that many mines have been operated for years and finally worked out and abandoned without experiencing an explosion. The absence of coal-mine explosions does not always indicate that effective efforts have been made to prevent them but rather that the nine has been fortunate in that the combination of circumstances necessary to cause an explosion has not existed. In view of present knowledge of the methods of preventing explosions, disasters are inexcusable and discredit the mining industry. The methods of preventing mine explosions are known to experienced, well-informed persons engaged in coal mining, yet despite this knowledge far to many coal-mine operators continue to use practices and methods that they should know have resulted in numerous explosions. Moreover, many mine workers persist in following past procedure irrespective of consequences and in breaking safety rules or indulging in practices almost certain eventually to result in disaster. Continued failure to apply known common-sense methods of accident and explosion prevention unquestionably will cell for ultimate enforcement of law.

Jan 1, 1940

By J. J. Hoeppner

Accurate determination of moisture in coals of various ranks has long been a subject of intensive investigation. Excellent reviews of methods developed over many years are given by Brown (9)4/ and, with experimental comparisons, by Goodman, Gomez, and Parry (11). As pointed out in these and other writings, one of the principal difficulties in assigning absolute merit to one or another procedure is the multiplicity of conditions under which water may exist in coal and the difficulties involved in obtaining sharp separation and distinction between these classes. Gauger (10) states: Water recoverable from coal is obtained from the following sources: (1) Decomposition of organic molecules (sometimes called combined water), (2) surface adsorbed water, (3) capillary condensed water, (4) dissolved water, and (5) water of hydration of inorganic constituents of the coal.

Jan 1, 1956

By Donlad B. Lindsay

This report describes a field-test program to determine the effectiveness of a polymeric wall sealant to reduce the excape of naturally occurring radio-active gas radon from the walls of an underground uranium mine into the ventilation air. A 75-foot-long, dead-end drift with a surface area of about 6,000 ft2 was used as the test site in which the average natural radon flux from the normally dry rock was 16 fCi/cm2-s. The effect on radon emanation of wetting the walls with water to a depth of 3 inches was tested, after which the rock was completely covered with a coating of dry-mix concrete to provide a base for the sealant, an acrylic latex. Sealant was applied in two coats to about 0.25 mm thick. An overall reduction of average radon flux of about 75 pct was achieved. Radon production and other environmental values were measured continuously and automatically by a Bureau of Mines data acquisition system. A commercial microcomputer was programed to convert raw data to engineering units and to perform other useful operations while recording all data on magnetic diskettes. Direct measurements of radon flux from the rock surface were made by a charcoal adsorption technique.

Jan 1, 1981

By Floyd R. Hertweck

This Bureau of Mines publication contains analyses and related source data for 349 natural gas samples from 26 States and 2 foreign countries. The 3 samples from foreign countries and 339 of the U.S. samples were collected during calendar year 1983. The remaining seven samples were collected earlier, but releases granting permission to publish were not received until 1983. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of these investigations are published annually to make the information available to the petroleum industry and the general public. Twenty-seven publications have presented the results of 13,332 gas analyses made prior to 1983. The first three bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26-27) containing 8,104 analyses of sam¬ples collected since 1960.

Jan 1, 1984

By John C. Cook

This was a study to identify and evaluate known technologies employing electromagnetic resonance phenomena in solid minerals for their identification and assaying, particularly assay logging of exploratory boreholes. A comprehensive literature search and study revealed some little known NMR (nuclear magnetic resonance) techniques developed by Professor G. J. Béné's group at the University of Geneva, Switzerland. These are suitable for use in weak, inhomogeneous magnetic fields. Laboratory NMR tests of numerous U.S. ore minerals showed good identifying signals from phosphates, fluorspar, bauxite, oil shale, and spodumene (lithium) ores, but not from the copper, lead, antimony or manganese ores tested. Use of EPR "signatures" for such ores is suggested. A conceptual design for an NMR assay logging system is proposed.

Jan 1, 1978

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By H. M. Lavender

This paper describing the inclined cut-and-fill, and the semishrinkage methods of mining at the Campbell mine of the Calumet and Arizona Mining Co. at Warren, Ariz., is one of a series being prepared by the United States Bureau of fines on mining methods, practices and costs in the various mining districts in the United States. The major portion of the production from the Bisbee mines of the company is mined by these methods. The total average yearly production for the last two years has been 493,612 tons of 5 per cent copper ore. The average employment in the mining department eras 940 men. With the exception of a small tonnage mined for the high iron and sulphur content, the ore is direct-smelting and is mined for its copper con¬tent and associated gold and silver values.

Jan 1, 1930

By Charles S. Allbright

This report describes hydrogenation of petroleum distillate fuels in bench scale equipment and the effects of hydrogenation on the storage stability and the composition of the fuels. Two distillate fuels were hydrogenated in laboratory equipment using a commercially available cobalt molybdate catalyst. Reactor temperatures were varied from 600° to 850° F and pressures from 100 to 600 psig. Product fuels were analyzed by ASTM, Bureau of Mines, mass, and infrared methods. Hydrogenation of a catalytically cracked fuel from Oklahoma crude oil significantly improved the storage stability, reducing insoluble gum formed during 9 months of storage at 110° F from 19.0 to 1.3 mg per 100 ml fuel, average. Conversion of the olefins to other hydrocarbon types varied with the temperature of hydrogenation--at 700° to 850° F the conversion was mainly to aromatics, at 650° F about 50:50 to saturates and aromatics, at 600° F principally to saturates. Processing a fuel composed of a mixture of virgin distillate and catalytically cracked stock, both from Illinois crude, at 700° F and 200 psig effected marked improvement in stability; the buildup of insoluble gum in storage was lowered from 18.3 to less than 1 mg per 100 ml fuel.

Jan 1, 1967

By D. E. Shanks

This U.S. Bureau of Mines (USBM) research simplified an earlier hydrogen chloride (HCI) leach-sparge process developed by the USBM to recover reduction-grade alumina from domestic kaolin clay. Improvements were made by decreasing the initial leaching acid concentration from 25 to 20 pet, decreasing the leaching time from 1 to 2 h to 15 to 30 min, eliminating the solvent extraction step for Fe removal, and eliminating the step to recover the AI content of the bleedstream circuit. A 10-cycle bench-scale experiment of the simplified process showed that the ferric chloride (FeC13) concentration built up to 9.3 g/L in the recycle stream. This did not interfere with any of the unit operations or final alumina product purity because Fe forms stable soluble chloride complexes when sparged with HCI and is easily washed from the large aluminum chloride hexahydrate (ACH) crystals. The reduced leaching time and acid concentration did not decrease Al extraction.

Jan 1, 2010

By Paul C. Turner

The U.S. Bureau of Mines, through an Interagency Agreement with the U.S. Army Tank-Automotive Command (TACOM), has successfully developed a steel expendable pattern casting process (EPC) for the manufacture of armorplate. The new armor is lighter and more ballistically effective than conventional rolled homogeneous armor (RHA), and costs less. An applique armor spinoff from the program was field-tested during the Gulf War. The applique armor withstood direct impacts from enemy munitions without failure.

Jan 1, 2010

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948