Search Documents

By T. G. Carnahan

The Bureau of Mines conducted research to simulate in situ leaching of a porphyry copper sulfide ore. The purpose was to determine the effects on copper leaching of additions of NaCI to a conventional sulfate leach system and to analyze the oxidant requirements and the oxidation products that resulted from leaching of the sulfide minerals in the ore. Baseline sulfate and sulfate plus 2-pct-NaCl-leach-solution experiments employing 167-kg (367-lb) and 152-kg (333-lb) charges, respectively, were conducted. The minus 25.4-cm (10-inch) ore was leached at 90° C under flooded conditions with 2.8 MPa (400 psig) of oxygen bubbling through the system. Sixty-seven pct of the copper was extracted in 1,236 days of leaching in the NaCI experiment, whereas 47 pct of the copper was extracted in 913 days of leaching in the baseline experiment. Diffusion into and out of the ore fragments controlled the rate of leaching, which precluded enhancement of the leach rate by the chloride ions. The calculated oxygen consumption was 3.17 kg/kg of copper extracted in the baseline experiment and 3.46 kg/kg of copper extracted in the experiment to determine the effect of chloride ions.

Jan 1, 1982

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.

By James Paone

The Bureau of Mines conducted laboratory drillability studies on nine rock types using two mining-type percussive drills. Percussive-bit action was simulated by dropping a known weight on a rock sample to obtain a coefficient of rock strength for each rock drilled. While no single physical property of a rock is completely satisfactory as a predictor of penetration rate, coefficient of rock strength showed a better correlation with penetration rate than did other physical properties. Results also indicate that over the range of energies investigated, energy per unit volume in a given rock is independent of blow energy. A drillability index for the percussive system is proposed that utilizes the coefficient of rock strength test to determine energy per unit volume for a given rock which, along with the work rate of a given drill and the bit diameter, is used to predict the penetration rate as shown in the following equation: [R = 4P pD2 E, where R = penetration rate, in/min, P = work rate, in lb/min, D = bit diameter, in, and Ev = energy required to produce a given volume of rock, in lb/in3.] Laboratory tests indicate this method's potential as a simple and reasonably accurate method of predicting penetration rates with any percussive drill and bit combination.

Jan 1, 1969

By R. D. Groves

Techniques were developed for preparing metallurgical-grade copper powder from industrially produced cement copper. Flotation was used for rejecting discrete gangue particles, acid leaching to remove residual iron and aluminum, hydrogen reduction to eliminate oxygen, sintering to consolidate the fine-sized copper, and grinding to obtain copper powder. Powders prepared from six different cement copper samples contained, in percent, 98.5 to 99.0 Cu, 0.10 to 0.05 Fe, 0.10 to 0.08 insoluble material and the remaining individual impurities less than 0.15 percent. The apparent density, flow characteristics, and other physical properties were suitable for powder metallurgy applications. An economic evaluation showed that this process was economically feasible. Processing costs appeared modest when considering that copper powder commands a price normally about 17.5 cents per pound over that of electrolytic copper.

Jan 1, 1971

By A. C. Fielder

It is with some diffidence that I venture to address the Montreal Section of the Society of Chemical industry on the subject of motor fuel from coal at a time when crude petroleum is produced in greater quantities than at any time in history, and at a time when the known reserves exceed all expectations, even the optimistic estimates of the Committee of Eleven of the American Petroleum Institute. Not only are new fields being discovered in America a -an embarrassing frequency but sources outside of the North American Continent show, unmistakable signs of adding materially to the world's sources of oil. Were it not for the tremendous scientific and technical importance of the work done in the past few years in transforming coal into liquid motor fuels, I should prefer to let this subject rest until a more propitious time, such as prevailed some years ago, when the gasoline consumption curve was rising rapidly and the production curve was slowing in its upward rise. That was the period which stimulated the researches which resulted in tetra ethyl lead and anti-knock gasolines on this side of the Atlantic and in methanol, synthetic gasoline and hydrogenation of coal on the other side. Some of you will recall a symposium on Motor Fuels and Oil Conservation held at the Chemists' Club n New York in September; 1925. Dr. R. L. Brown and I presented a paper at this meeting on "Complete Utilization of Coal and Motor, Fuel, in which we pointed out that coal was the most likely raw material source of gasoline substitutes if and when needed. We grouped the present and future, processes' for obtaining motor fuel from coal in three classes, namely:

Jan 1, 1928

With a growing concern over mine fires, prevention and suppression are hot topics. NIOSH researchers Michael Trevits, Alex Smith and Edward Thimons discuss their research in the area. The leading causes of US mine fires include flame cutting and, welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions and spontaneous combustion. From 1990 through 2007, there were 1601 reportable fires that occurred in the US mining industry -an average of 89 fires per year. The fact that mine fires are occurring with alarming regularity reinforces the importance of recognizing and eliminating the potential hazards. These statistics also show the need for improved control and suppression technology to ensure worker health and safety if a mine fire does occur.

Jan 1, 2008

By Richard N. Appling

This compilation presents information obtained through investigation of manganese deposits and a reconnaissance of potential manganese-bearing areas of southwestern Oregon and Del Norte County, Calif., from October 1952 to September 1955. The report includes maps, assays, and preliminary examination data on 39 manganese deposits distributed throughout Curry, Coos, Douglas, Josephine, and Jackson Counties, Oreg., and 1 deposit in Del Norte County, Calif. On the basis of mineral content the deposits can be divided into three groups: 1 Manganese silicate deposits, manganese oxide deposits, and manganiferous iron de-posits. Generally the oxides occur along the coast in the Curry-Coos County area, the manganiferous iron deposits are in the Josephine-Douglas area, and the manganese silicates are found in both the Josephine-Douglas and Jackson County areas. The deposits are characteristically irregular in form and usually small. Most silicate and manganiferous iron deposits are in metasediments of Triassic (?) age; oxide deposits are in sediments varying in age from Jurassic to Eocene.

Jan 1, 1957

Several federal and state agencies have promulgated regulations that require the installation of operator protective structures on mobile equipment used in mining, construction, agriculture and logging industries. These regulations cover many different types of vehicles, from small farm tractors to large rubber-tired front-end loaders, and require structures that help protect the operator from death or injury from vehicle overturns, from falling tree tops and logs, from falling rocks, and from tree limbs in clearing operations. Two general types of vehicle operator protective structures have evolved over the past twenty years. The first of these is the "Roll-Over Protective Structure" or "ROPS" that is essentially a "roll bar" or "roll cage" that provides a relatively safe area for the vehicle operator if the vehicle should tip over and roll. The second protective structure is the "Falling Object Protective Structure" or "FOPS" that provides overhead protection against falling material. The terms "ROPS" and "FOPS" are often used interchangeably (sometimes inaccurately) with "cabs", "canopies", "roll bars', "protective structures" and other such descriptive names. In this report, 'ROPS" describes the function of the structure; 'FOPS" also describes a particular function. Thus a ROPS/FOPS could describe a cab or a canopy that provides both roll-over protection and falling object protection.

Jan 1, 1976

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

By James F. O'Neill

Brown iron ore resources in Barbour , Butler , Crenshaw , and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama . The aggregate footage drilled was 18,010 linear feet . When developed , reserves of 12,664,000 long tons of crude ore were indicated , containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet . Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons . Beneficiation of samples by simulated log washing and use of a 1 / 8 - inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese . Screen- test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200 - mesh screen . Clay was prominent in micron - size slimes . Silica was deleterious in the minus 20 - mesh size . While an indicated 2,198,000 dry long tons of usable iron ore can be recovered , sink - and - float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing . However , applicable commercial processes have not been demonstrated .

Jan 1, 1965

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By Louis C. Brichta

The rapid depletion of known deposits of high-grade ore and the need for development of additional reserves, together with increased interest in open-pit mining of low-grade zinc-lead ores in the Tri-State District, led the Bureau of Mines to examine likely mining sites. Underground operations failed to remove all of the ore in a number of areas, and it appeared possible that some of them might be reworked successfully by low-cost open-pit methods. The South Carthage or Hull tract in Jasper County, Mo., was selected by Bureau engineers as favorable for the development of an open-pit mine.

Jan 1, 1949

By S. L. May

Procedures for separating columbium and tantalum have been developed by the Bureau of Mines as part of a broad research program on the utilization of low-grade ores of columbium and tantalum, Columbium and tantalum compounds of greater than 99 percent purity have been obtained by application of the solvent extraction separation system: Hydrofluoric acid-sulfuric acid-methyl iso-butyl ketone. This system is unique in that it not only separates columbium from tantalum, but also separates these two metals from other metallic impurities. The system is effective for separating the metals irrespective of the tantalum and columbium ratio of the starting materials. Investigations in which the spent feed obtained from the initial coextraction step was recycled to the system indicated that efficiency was increased, and cost was reduced without impairing product purity. Continuous tests demonstrated that this solvent extraction system could be used in large-scale equipment without loss in efficiency or in purity of products. The separation of columbium and tantalum has been difficult because of the similarity in their chemical bahavior. Many methods have been proposed for separating these two elements, but most methods either did not achieve satisfactory separation or were tedious and time consuming. The Marignac process (3, 4)4 developed in 1866 was the only method used commercially until recently. This separation procedure is based on the difference in solubility in aqueous solution of potassium tantalum fluoride and potassium columbium oxyfluoride. Current commercial practice appears to favor solvent extraction as a method for separating tantalum from columbium (1). Several efficient methods for separating columbium from tantalum by solvent extraction (2, 9, 8) were reported earlier from this laboratory.

Jan 1, 1961

By Foster Fraas

The objective of this research was separation of one highly conductive mineral from a second conductive mineral , a procedure which is impractical in commercial electrostatic separators using metal rolls . Such separators permit separation of nonconductive from conductive minerals . A new technique involved use of carrier electrode rolls specially prepared by anodizing and / or oxidizing at high temperatures to form suitable oxide surfaces . Specific oxides included aluminum , copper , and nickel . The significant result provided by the new surfaces was the extension of the separation range to higher conductivities , an extension in relative mineral conductivity from 10-14 mhos . The results are in accordance with the blocking- layer theory .

Jan 1, 1964

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By L. H. ADAMS, C. N. HASKINS, J. K. CLEMENT

In the course of its investigations of the fuel resources in the United States and of the methods by which these resources could be utilized with greatest efficiency, the United States Geological Survey tested a great variety of coals and lignites as gas-producer fuel. Early in these testa it was found that many factors controlling the formation of gas in the generating chamber of the producer and, consequently, having a direct bearing on the management of producer-gas plants, were not as well understood as they should be. The Geological Survey therefore took up a detailed investigation of the chemical and physical processes that take place in the producer, keeping in view not only the possibility of increasing the efficiency of the producer as a source of energy, and the ensuing benefits to the public of cheaper power and greater utilization of low-grade fuels, but also the application of the results to the problems of boiler-furnace operations. - The Bureau of Mines, to which the testing and analyzing of fuels as carried on by the United States Geological Survey has been transferred, is continuing producer-gas investigations at the testing station at Pittsburg, Pa. Results of the gas-producer tests a made at the coal-testing plant erected at St. Louis, Mo., and of a study of some of the problems° that came up in the tests have been published by the Geological Survey. Results of the tests made at Norfolk, Va., and Pittsburg, Pa., and of further studies of particular problems, will be published by the Bureau of Mines. In the gas producer solid fuel is transformed into more readily combustible gaseous fuel. The transformation is relatively slow and consists of several processes: 1. The distillation of the volatile hydrocarbons from the freshly fired fuel at relatively low temperatures. 2. The combustion of the fuel by its combining with the oxygen of the air forming carbon dioxide (COO. 3. The formation of carbon monoxide (CO) and hydrogen (11 3), the essential constituents of producer gas, in accordance with the equations:

Jan 1, 1911

By David J. Kusler

This report describes a rapid, reliable, and relatively simple method developed by the Bureau of Mines Pyrometallurgy Laboratory at Bruceton, Pa., for determining lime (calcium oxide) and magnesia (magnesium oxide) in various materials containing these constituents in greater than trace amounts. Optionally, titania (titanium dioxide) may be determined for the same sample. The accuracy of the method, suitable for most purposes, is shown by comparing the Bureau results with those obtained by accepted procedures. The method has been applied satisfactorily to the routine analysis of blast-furnace slags, for which purpose it was primarily developed, and to other calcareous compositions. In the Pyrometallurgy Laboratory it has replaced the standard methods previously used to determine lime and magnesia, and has been in general use by that laboratory for the past several years. The analysis time, generally under 3 hours, is considerably less than required by standard methods.

Jan 1, 1960

By A. E. Back

[Several processes for recovering manganese from low-grade ores have been proposed3/4/5/ in which an aqueous slurry of the ore is leached with gas containing nitrogen, oxygen, and sulfur dioxide as obtained from burning sulfur or roasting sulfide ores. The manganese dioxide is dissolved, and most of the sulfur dioxide is oxidized to sulfate, but an appreciable quantity of dithionate is usually formed, together with acid from oxidation of the sulfur dioxide. The over-all reactions may be represented as follows: (1) Mn02 + S02 = Mn++ + S04--. (2) Mn02 + 2S02 = Mn++ +S206--. (3) H20 + So2 + 1/2 02 = 2H+ 5S4--. (4) H20 + 2S02 + 1/2 02 = 2H+ + S206---.]

Jan 1, 1952

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986