Search Documents

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Ren G. Dong, Dan E. Welcome

Instrumented handles or dynamometers are widely used to measure hand forces and/or the biodynamic response of hand-arm system. To study hand-transmitted vibration exposure, six generations of instrument handles were constructed or initially developed by researchers in ECTB/HELD/NIOSH. This presentation provided a summary of these handles. Their basic characteristics, limitations, and usefulness are described, which may help their appropriate applications and further improvements. Six Designs of Instrumented Handles Handle 1: The conceptual design is recommended in ISO 10819 (1996)1 for glove test. The grip force is measured by detecting bending strains on a measuring beam in the handle. A special handle fixture was designed to connect the handle to a shaker. Except the screws, the handle and fixture were made from aluminum. Handle 2: The design is based on the principle of shear strain measurement.2-3 Both grip and push forces can be measured simultaneously using this handle. This handle was directly designed for a simulated vibrating tool. Handle 3: This design is basically composed of a handle base, a measuring cap, and two charge-based sensors (Kistler 9212) sandwiched between the base and cap. The handle was also made from aluminum. The fixture for Handle 1 was also used with this handle. This generation of handle has three different handle diameters (30, 40, and 50mm).4 Handle 4: This design is an improvement from Handle 3. The handle fixture was totally redesigned and it was much stiffer than the previous one. The aluminum measuring cap was replaced with a magnesium cap. Handle 5: The basic structure of this handle is the same as that for Handle 3. However, the piezoelectric sensors were replaced with two strain gage based sensors (Interface SML-50). Handle 6: This handle includes two measuring caps, four piezoelectric sensors, and a handle centre base. The handle fixture was the same as that with Handle 4. Methods for Handle Examinations The static and dynamic characterizations were performed using the methods reported by Dong et al.5-6 Results and Discussion Handle 1: The static force measurement depended on the hand grip location on the handle. Its natural frequency was less than 200 Hz.5,6 Because the transmissibility of gloves may not vary significantly with the applied grip force, this handle may be acceptable for glove test. However, the force measurements with this handle may not be reliable. Handle 2: The static force measured with this handle was insensitive to the hand acting location. However, when the handle was vibrating, the force signals could be totally distorted. For this reason, it was not used for vibration studies.

Jan 6, 2006

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By Vern L. Kegler

This paper is one off a series dealing with mining methods and costs, sponsored and published by the United States bureau of Mines. ACKNOWLEDGMENTS The author acknowledges the, constructive and helpful suggestions and criticism of W. F. Lamoreaux, vice-president, and general manager of the Ducktown Chemical & Iron Co. United States Geological Survey Professional Paper- 139, by W. H. Emmons and F. B. Laney, has been drawn upon for some of the information contained in the paragraphs or history and geology.

Jan 1, 1931

By F. C. Houghten, R. R. Sayers, C. P. Yalaglou

"Introduction.Atmospheric conditions relative to high temperature and humidity are of great importance in mining, as well as in such allied fields as railroad and vehicular tunnels. An extended investigation into the effect of these factors on men has been in progress for some time, both in the field under actual working conditions, and at the Pittsburgh experiment station of the bureau in cooperation with the American Society of Heating and Ventilating Engineers and the U. S. Public Health Service.For several years one of the writers (Dr. Sayers) and L. Harrington, supervising mining engineer of the bureau, have been studying the effects of hot humid atmosphere in metal mines on the comfort and efficiency of the workers. Some of the reactions experienced in still and in moving saturated mine air at temperatures of 90 to 100°F., with men at rest are presented in a recent paper.****The present paper is based on experiments made under carefully controlled conditions to determine the relative feeling of warmth experienced by men in atmospheres of various degrees of temperature and humidity. The work was conducted by the research laboratory of the American society of Heating and Ventilating Engineers, at the Pittsburgh experiment station of the Bureau of Mines, in special physchrometric chambers built for this purpose. It was carried on under the direction of F. Paul Anderson, director of the laboratory, Dr. R. R. Sayers and A. C. Fieldner of the Bureau of Mines. The results given in this paper are for still air only. Investigations of the effects of moving air are being continued, and will be reported later."

Jan 1, 1924

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

By Michael J. Jorgensen, Anoop Polsani, Khurram S. Khan

Riveting operations in aircraft manufacturing involves the use of power tools for manually drilling holes for the rivets, power drills for the setting of the holes for the rivets, as well as rivet guns to drive and set the rivets. To close the rivet, the rivet is driven against a metallic bar commonly called a “bucking bar”. The bucking bars are typically held firmly to increase the quality of the riveting, as well as keep the bucking bar from “dancing” against the metal piece being riveted. Thus, employees in aircraft manufacturing involved in riveting are exposed to hand-arm vibration from several sources, and epidemiological evidence suggests that vibration-related musculoskeletal disorders are associated with long term exposure to riveting tasks in the aircraft manufacturing of aircraft.1,2 Recently, tungsten technology has been introduced into aircraft manufacturing for bucking bars, which are heavier than traditional steel bucking bars of the same size. Rivet guns with tungsten pistons instead of steel pistons have also recently been introduced with the objective of reducing vibration exposure to the riveter. The objective of this study was to assess vibration characteristics of steel and tungsten bucking bars and rivet guns to identify the combination that simultaneously reduced the combined exposure to both the “riveter” and “bucker”. Methods Vibration (10g tri-axial accelerometer, Biometrics S2-10G-MF Series 2) was measured from eight experienced employees using seven different rivet guns on size 6 rivets, with the same person bucking for all subjects. Vibration was also measured on two different bucking bars for these same eight subjects, with the same person driving the rivets using the various rivet guns. The rivet guns consisted of three E4 steel piston guns with different RPMs (Guns A-E4, B-E4, C-E4), an E4 vibration dampened rivet gun (Gun D-E4D), an E3 steel piston rivet gun (Gun E-E3) and an E3 and E4 tungsten piston rivet guns (Guns F-E3T and G-E4T). The bucking bars were made of 90% tungsten (1694g) and cold-rolled steel (843g), and were the same shape and size. A two-way repeated measures analysis of variance was performed on the vibration (mean frequency weighted resultant acceleration) on both the rivet gun side and the bucking bar side, and mean rankings were used to assess the vibration simultaneously for the rivet gun and bucking bars to investigate which combinations provided the lowest vibration exposure. Results Frequency weighted resultant acceleration was significantly lower on the E3 tungsten (F-E3T) rivet gun than the E4 steel piston (B-E4) and the E4 tungsten piston (G-E4T) rivet guns (Figure 1). When measuring vibration on the bucking bar, the E4 (A-E4) steel piston rivet gun resulted in lower vibration on the bucking bars than the E4 tungsten piston (G-E4T) and E4 vibration dampened (D-E4D) rivet guns (Figure 2). Additionally, use of tungsten bucking bars resulted in a 35% decrease in resultant frequency weighted acceleration than when using steel bucking bars.

Jan 6, 2006

By Clive Ellis, Brian Davies, Steven E. Mischler, Jon C. Volkwein

A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclusion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air. A primary means to reduce environmental levels of diesel particulate matter (DPM) exposure to miners is to reduce the amount of DPM emission from the engine. A quick and economic method to estimate engine particulate emission levels has been developed. The method relies on the measurement of pressure increase across a ?lter element that is brie?y used to collect a DPM sample directly from the engine exhaust. The method has been re?ned with the inclu­sion of an annular aqueous denuder to the tube which permits dry ?lter samples to be obtained without addition of dilution air. Tailpipe ?lter samples may then be directly collected in hot and water-supersaturated exhaust gas ?ows from water bath-cooled coal mine engines without the need for dilution air.

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Occupational noise-induced hearing loss continues to be one of the most pervasive health problems in the mining industry, despite over 25 years of regulation. One of the loudest pieces of equipment used in underground mining is the continuous mining machine. Noise sample data collected by the Mine Safety and Health Administration indicate that 42% of noise overexposures between 2000 and 2005 involved continuous mining machine operators. Previously conducted field and laboratory tests have determined that the continuous mining machine conveyor system is a dominant noise source. Loud impacts occur as the conveyor chain flight bars, used to move the mined aggregate, traverse their path from the top to the underside of the conveyor deck. Various noise control treatments have been applied to abate noise caused by the conveyor system. A durable polyurethane coating has been developed for the conveyor flight bars, resulting in a time-weighted average reduction of 3 dB(A) for an eight-hour work shift. In an attempt to further reduce continuous mining machine operator overexposures, a similar urethane coating has been applied to the tail roller component of the conveyor system. Laboratory results showed a 2 dB(A) reduction in sound power levels, but the component failed during underground durability testing. An outer steel sleeve has been added to the urethane coating of the tail roller to enhance wear resistance during mining. The urethane jacketed tail roller is the latest effort, combined with previous noise treatments, to bring the continuous mining machine into compliance with federal noise regulations.

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

By D. S. Colby

Statistics on the volume of natural gas produced in the United States were first collected for 1906. A summary of those statistics covering 1906-35 was incorporated in the 1937 Minerals Yearbook. This summary, covering 1936-50 presents, by States, a number of the more important statistics that have appeared in the natural-gas chapter of the Minerals Yearbooks. The period covered has been one of rapid expansion, especially of long-distance transmission lines. Natural gas was made available to some States for the first time; in other States the degree of dependence upon supplies transported from outside their boundaries changed rapidly. Thus, an isolated series of statistics cannot be studied without considering other regional influences that reflect in the overall operations of the industry. These tables accordingly have been designed to show for each State the simultaneous changes taking place in the various sectors surveyed. The tables show production data in the upper portion and consumption data in the lower portion. They are arranged alphabetically, by States. A copy of the 1906-35 production summary from the 1937 Minerals Yearbook has been included.

Jan 1, 1952

By B. J. Moore

This publication contains analyses and related source data for 234 natural gas samples from wells and pipelines in 21 States and 1 foreign country. All of the samples were obtained and analyzed during calendar year 1975 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and n special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Seventeen previous publications have presented the results of 10,831 gas analyses prior to 1975. The first 3, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 14

Jan 1, 1976

By Gerald T. Homce, James C. Cawley

This paper updates an earlier report by the authors that studied electrical injuries from 1992 to 1998. The previous information is expanded and supplemented with fatal and nonfatal injury rates and trends through 2002. Injury numbers and rates were used to compare and trend electrical injury experience for various groups and categories. This information allowed identification of at-risk groups that could most benefit from effective electrical safety interventions. The data presented in this paper are derived from the U.S. Labor Department’s Bureau of Labor Statistics’ Census of Fatal Occupational Injuries (CFOI), Survey of Occupational Illnesses and Injuries (SOII) and Current Population Survey (CPS). Between 1992 and 2002, 3,378 workers died from on-the-job electrical injuries. Electricity remained the sixth leading cause of injury-related occupational death. From 1999 through 2002, 4.7% of all occupational deaths were caused by electricity, down from 5.2% in the 1992 to 1998 time period. The cause of death was listed as electrocution in 99.1% of fatal cases. Contact with overhead power lines was involved in 42% of all on-the-job electrical deaths. The construction industry accounted for 47% of all electrical deaths between 1992 and 2002, but showed overall improvement from 1995 through 2002 by reducing its electrical fatality rate from 2.2 to 1.5 per 100,000 workers. An additional 46,598 workers were nonfatally injured by electricity. Contact with electric current of machine, tool, appliance, or light fixture and contact with wiring, transformers, or other electrical components accounted for 36% and 34% of nonfatal electrical injuries, respectively. Contact with underground, buried power lines was involved with 1% of fatal injuries and 2% of nonfatal injuries. NIOSH research aimed at evaluating commercially available overhead power line proximity warning alarms is described. This research is expected to be the initial step for eventual development of a performance standard for such systems.

By S. M. Moore

Technological advances in underground coal mining have reduced fatalities but may not have reduced worker exposure to cumulative injury risk factors. The objective of this study was to evaluate the prevalence of cumulative injuries before and after the implementation of technological advances in underground coal mining and to make a general cost estimate for these injuries. A previously published algorithm was utilized to identify cumulative injuries within the Mine Safety Health Administration (MSHA) database for two data sets: 1983-1984 and 2003-2004. For both, the following were determined: the number and percentage of cumulative injuries, the average days lost, the average age at the time of injury, the average years of experience and the general cost estimate by body part. The percentage of cumulative injuries remained largely unchanged (37 percent in the 1983-1984 period and 33 percent in the 2003-2004 period). The average number of lost days due to cumulative injuries increased (36±55 days and 62±82 days, respectively), which may have been due to the increased worker age (seven years older in the 2003-2004 period), increased length of employment (seven years longer in the 2003-2004 period) or other factors such as changes in medical practices. Cumulative injuries to the back decreased by 10 percent, while cumulative injuries to the knee increased by 8 percent. The reduction in back injuries may be due to the implementation of assist devices, while the increase in knee injuries may be related to kneeling/crawling in low-seam mines. Cumulative injuries were found to remain a major financial burden on the industry. Recently, National Institute for Occupational Safety and Health (NIOSH) developed tools to assist mining companies with incorporating an ergonomics process into their existing health and safety programs. The participating companies have reported tremendous success. Therefore, it is recommended that ergonomics processes be implemented as a means to systematically identify and address the root causes to cumulative injuries and ultimately reduce costs.

Jan 1, 2008

By Robert M. Cox

The U. S. Bureau of Mines (USBM) MULSIM/NL modeling technique has been used to analyze anticipated stress distributions for a proposed alternative longwall gate road design for a western Colorado coal mine. The model analyses indicated that the alternative gate road design would reduce stresses in the tailgate entry without increasing stresses in the headgate entry. To test the validity of the alternative gate road design under actual mining conditions, a test section of the alternative system was incorporated into a subsequent set of gate roads developed at the mine. The alternative gate road test section was instrumented with borehole pressure cells, as part of an ongoing USBM research project, to monitor ground pressure changes as longwall mining progressed. During the excavation of the adjacent longwall panels, the behavior of the alternative gate road system was monitored continuously using the USBM computer-assisted Ground Control Management System. During these field tests, the alternative gate road system was first monitored and evaluated as a headgate, and later monitored and evaluated as a tailgate. The results of the field tests confirmed the validity of using the MULSIM/NL modeling technique to evaluate mine designs.

Jan 1, 2010

By P. -E. Boileau, P. Marcotte, Y. Aldien, S. Rakheja

A number of biodynamic models of the hand-arm system have evolved on the basis of measured driving-point mechanical impedance (DPMI) responses to facilitate analyses of the coupled hand-tool system [1]. The parameter identifications in such models are based upon minimization of an error function of the model and the target impedance data, which may not yield a unique solution. Consequently, a number of model structures and parameter sets could be realized that would equally satisfy the target curve. Moreover, the vast majority of the reported models exhibit acute deficiencies due to excessive static deflections of model masses, presence of a low frequency mode and very light masses in the order of 1.2- 4.8 grams. The models also do not characterize the dependency of the biodynamic responses on many factors, namely the hand forces, hand-arm posture and vibration intensity. This study aims at development of a hand-arm biodynamic model with considerations of the hand forces, and both the DPMI and power absorption measures, to enhance the uniqueness of the model. Methods Two different model structures are chosen for identifying the model parameters on the basis of measured DPMI and absorbed power characteristics of the hand-arm system under zh-axis vibration over a range of hand-grip and push forces. Owing to the strong influence of the hand-handle coupling forces, the models were initially derived for fixed hand forces, namely 30 N grip and 50 N push forces, as suggested in the ISO 10068 standard [2]. The equations of motion for the model are formulated and solved to compute both the DPMI and absorbed power responses. A constrained minimization function comprising weighted errors of both the DPMI and absorbed power is formulated and solved to identify the parameters. Alternate functions corresponding to different combinations of hand forces are then applied to identify hand-force dependent model parameters. Variations in the model parameters are investigated as functions of the grip, push and coupling forces through linear regression analysis. Regression-based models are formulated for deriving the hand-handle forces dependent model parameters. The validity of the model is also examined under selected combinations of hand forces. [ ]

Jan 6, 2006