Search Documents

By E. M. Frost

"A new apparatus has been devised for quickly and precisely analyzing natural gas for its helium content. The following outstanding advantages make it far superior to any equipment now available for the purpose.3/4/5/6/1. It enables more rapid determinations to be made.2. It has far greater sensitivity than previous apparatus. 3. It is portable.Fifty or more samples may be analyzed in an 8-hour day with the new apparatus and procedure. A maximum of about 10 samples per day could be analyzed with previous apparatus. In the apparatus described, the volume of pure helium obtained from a sample is determined by measuring the pressures created by that pure helium when it is expanded into a constant calibrated volume. In older methods the pure helium separated from a sample is pumped into a burette and measured at atmospheric pressure. The new apparatus and Procedure used with it reduce the average time for an analysis from about 40 minutes to less than 10 minutes,Samples containing a few thousandths of a percent helium may be analyzed as readily as samples containing 1 percent or more, This was not possible with former apparatus. Duplicate samples containing a few thousandths of a percent helium have been analyzed, results checking to one ten-thousandth of a percent. Attempts to measure a corresponding volume of helium in a burette at atmospheric pressure become futile. The ability to determine very small quantities of helium has become of great importance recently in gas- and oil-field engineering studies such Os the utilization of helium as a tracer gas in following the movement of gases through underground structures.A complete apparatus was recently carried more than a thousand miles in a passenger automobile. It arrived without breakage, was .set up and ready to make an analysis in a few hours. .Former apparatus was not portable. The portability of the present apparatus permits taking the apparatus to the field for more efficient prosecution of field engineering problems. The only services required in the field are electricity, tap water, and a source of liquid air or liquid nitrogen.The principle involved is based upon the fact that large volumes of all the constituents usually found in natural gas, except helium, are adsorbed quantitatively on cocoanut charcoal that has been cooled to the temperatures of liquid air. A volume of sample is measured and transferred to a tube of cocoanut charcoal maintained at the temperature of liquid air. After adsorption of all the constituents other than helium, the charcoal tube is connected to a sensitive pressure-measuring device, and the Percentage helium originally in the sample is calculated from two pressure readings and the volume of the original sample."

Jun 1, 1946

By Rimas Pakalnis, Doug Milne, Marc Ruest, Lewis Martin

Whereas many researchers and mine engineers have conducted tests on cable bolts using various grouts, water: cement ratios, and physical modifications of the cable to determine the load-carrying characteristics ofa bolt, few studies have been conducted on cable bolts fitted with internal instruments. Those studies that have been done have concentrated on cable response averaged over significant (6.1 m) cable lengths. Researchers at the Spokane Research Laboratory (SRL) of the National Institute for Occupational Safety and Health in Spokane, WA, are investigating the physical properties of cable bolts by replacing the conventional king wire with a modified king wire on which strain gauges have been installed. A numerical analysis was performed to match laboratory results. Loads calculated by the model were then compared to loads measured in the laboratory on 1.83-m-long cables grouted into two 0.91-m-long pull-tube assemblies. Load along the cable was monitored with 20 strain gauges installed along the length of the cable. This paper documents test results on these modified cable bolts. The instrumented cable bolt provided reproducible point measurements of cable load as opposed to load measurements averaged over long cable lengths. Such point measurements can assist in interpreting the influence of cable confinement, grout quality, rock mass stiffness, and other factors. The instrumented cable bolt is a practical field and research tool because it can predict point loading along the cable. The instrument has been successfully field tested at FMC's Granger Mine, Granger, WY; the Meikle Mine, Carlin, NV; the Stillwater Mine, Nye, MT; and the Getchell Mine, Golconda, NV. By monitoring load and displacement of the rock mass using these instrumented bolts, more-effective ground support can be selected and installed, which will lead to safer working conditions for miners.

Jan 4, 2004

By R. S. Warfield

The Kasna Creek copper deposit near Lake Kontrashibuna in the Lake Clark region, Alaska, was the object of an investigative project by the Bureau of Mines during the fall of 1948. Recessed because of inclement weather, it was completed in 1949. This project was a part of the Bureau of Mines program in Alaska for the development of critical and strategic minerals. The ore bodies are contact-replacement deposits in limestone. Mineralization is mainly specular and micaceous hematite associated with chalcopyrite, calcite, chlorite, quartz, and amphibole. The deposit, on the right limit of Kasna Creek approximately 2 miles from the shore of Lake Kontrashibuna, is composed of two mineralized zones that range in altitude from 2,350 to 2,650 feet. This report contains a brief history of the prospect, description of the physical setting of the property, its geology, and the factual results of the Work performed by the Bureau of Mines.

Jan 1, 1951

By W. W. Adams

[The quantity of explosives sold in the United States in January, 1931, for domestic consumption, amounted to 368,100 kegs (9,202,510 pounds) of black blasting powder, 4,810;000 pounds of permissible explosives, and 16,533,000 pounds of high explosives other than permissible. These figures are based on reports received by the United States Bureau of Mines, Department of Commerce, from nearly all manufacturing companies, and include an estimate of sues by several companies that do not furnish monthly reports. Reports actually received from manufacturers shored sales of 365,977 kegs of black blasting powder (consisting of 220,892 kegs of granular powder and 145,085 kegs of pellet powder), 4,687,900 pounds of permissible explosives, and 15,498,152 pounds of high explosives other than permissible. Sales in January, 1931, were smaller than in January last year, the decreases being 14 per cent for black blasting powder, 19 per cent for permissible, and 17 per cent for high explosives other than permissible. Sales in January 1931 when compared with soles in December 1930, show increases for all three classes of explosives as follows: 2 per cent for block blasting powder, 16 per cent for permissible explosives, and 7 per cent for other high explosives. PERMISSIBLE EXPLOSIVES: Of the 4,687,900 hounds of permissible reported sold during January, 97 per cent was used for coal-mining operations, Including 32 per cent for anthracite mines and 65 per cent for bituminous mines. The following Staten were the largest users of permissible explosives daring January: Pennsylvania, West Virginia, Illinois, Alabama, Kentucky, Indiana, and Utah. Their combined sales represented 89 per cent of the entire sales reported for this class of explosives.]

Jan 1, 1931

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By Hillary W. St. Clair

This report describes an experimental method for determining parameters for the rate of reaction of CO2 with solid carbon. The method involves the simulation of a flow reactor by a mathematical model based on a hypothetical multistage reactor which permits calculation of the analyses of effluent gas and carbon consumed as functions of the flow rate and duration of the reaction. The method is applied to experimental data on the reaction of coke with CO2 in fluidized-bed and fixed-bed flow reactors. A method is described whereby two parameters may be determined simultaneously. The method involves a reiterative procedure that finds the values of the parameters that minimize the sum of squares of deviation between calculated and observed analyses of the effluent gas.

Jan 1, 1971

By Edwin B. Cook

This report presents the results of calculations of the equilibrium composition of the products of combustion with air of six different mixtures of octane CgH18, plus PbEt4 and halogen-bearing scavengers at three air-fuel ratios, at pressures of 5 and 30 atm., and at temperatures of 350°, 1,000°, 1,800°, and 2,000° K. The air-fuel weight ratio has the values 12, 15:12, and 18. The concentration of PbEt4, M, in milliliters per gallon of iso-octane, has the value 1 or 3. The word "case" is used to designate the halogen concentration. Three cases have been considered [ ]

Jan 1, 1953

By A. B. Hooker

The flame safety lamp with metal-gauze enclosure was invented by Sir Humphrey Davy more than a century ago, primarily for its safe light; however, it soon became the standard device for detecting the presence of methane in mine atmospheres. It still is the most widely used device for this purpose and is also the most practicable means of detecting deficiency of oxygen in coal mines. A permissible flame safety lamp is similar in all respects to one that, after a series of tests, has been approved by the Bureau of Mines as safe for use in gassy mines. However, safety depends largely upon the way lamps are maintained and used.

Jan 1, 1944

By G. W. Jones

"INTRODUCTION As part of its work in promoting safety, the Bureau of Mines is investigating various means of eliminating or mitigating the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explosibility of many complex gaseous mixtures may be calculated in a rather simple manner without the necessity of performing laborious laboratory experiments. An earlier publication 3/ described the method of determining by calculation the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen. The information published in the above report permitted calculation of the limits of inflamnability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust gases, gases present after mine explosions, blast-furnace gas, and other gases of similar type.Gases liberated in certain potash mines in the western part of the United States sometimes contain ethane, in addition to the gases named. An investigation was made to obtain data from which the limits of inflammability of such gaseous mixtures could be determined by calculation. 4/Similar data have been Published covering all types of natural gases containing wide ranges of concentration of nitrogen and carbon dioxide.5/"

Dec 1, 1944

By G. J. Conroy

This Bureau of Mines study was initiated to determine whether or not a large-scale investigation of 400-Hz applications in coal mines was justified as a means of increasing safety in operations due to size and weight reductions in portable and other mining machinery. Potential uses for 400-Hz power in mining operations are explored, and cost and size comparisons with 60-Hz systems are made. The use of variable-frequency motor drive is suggested for conveyors. The conclusion was reached that there is no significant potential safety increase due to a general size and weight reduction, as the fact of such general reduction cannot be demonstrated.

Jan 1, 1974

By A. C. Rice

Investigation of a variety of mines to determine efficiency for rare- earth extraction has resulted in a solvent extraction technique wherein Primene 81-R,4 N-benzylheptadeeylamine (BHDA), and Primene JM-T give favorable extraction from sulfate solutions. Extraction from chloride, nitrate, and perchlorate solutions is negligible. Distribution coefficients for 10 rare-earth elements with Primene 81-R establish an extraction sequence beginning with lanthanum and proceeding through lutetium according to atomic number. Yttrium and ytterbium are exceptions in the extract ion sequence.

Jan 1, 1962

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By M. S. Fleming

The objective was to evaluate central lubrication systems for potential use on underground mining equipment. Previous use on continuous mining equipment resulted in poor system performance because of improper selection of lubricants, component failures, and an inconsistent delivery of lubricant to the bearings. The principles and operational characteristics of systems are reviewed and evaluated, and it was concluded that systems are available which can provide reliable central lubrication if properly applied, installed, and maintained. The procedures for applying a system to a continuous miner are discussed. Investigation revealed the lack of significant information on lubrication-related equipment failures and injuries related to maintenance and repair operations, the lack of significant failure rate data for central lubrication system components, and the lack of performance standards for central lubrication systems and components. To continue the development of systems for underground mining equipment it is recommended that a data bank on failures and reliability for equipment with and without central lubrication systems be created, and standardized specifications and performance criteria be developed for central lubrication systems and components which will be used on underground mining equipment.

Jan 1, 1979

By Steven R. Munts

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the South Providence Wilderness Study Area (WSA) in 1982. No mines are currently operating in the WSA, however, the Golden Gift Mine in the southeastern part of the WSA produced $6,800 1/ worth of gold and silver and five mines adjacent to the east boundary of the WSA had a total production of about $3,500,000 1/ in gold, silver, lead, and copper. There is no recorded placer gold production. Over 350 lode and placer mining claims are in and immediately adjacent to the WSA. Of these, 74 were actively held (1982) and at least one area, which is partly within the northeast portion of the WSA, was being actively explored by private industry in 1982. Adjacent to the southeastern border of the WSA the Big Horn Mine contains an estimated 200,000 tons of indicated and inferred marginal reserves averaging 0.25 oz/ton gold; and the Hidden Hill Mine has 550 tons of subeconomic resources averaging 0.60 oz/ton gold. An additional 11,000 tons of marginally economic gold-bearing dump reserves average 0.17 oz/ton gold at the Bighorn, Hidden Hill, and the Buena Vista Mines and the Midas Touch Prospect. Sample analyses indicate eight mines and prospects in, and five adjacent to the WSA may have additional gold-silver-lead-copper vein-type resources. Five of these prospect areas may have a disseminated gold resource and one may have gold resources in a skarn. One prospect may have a porphyry-type copper-molybdenum resource. Although gold placer claims were filed sporadically throughout the WSA, none appears to have placer gold resources. Likelihood for mining is greatest at the Big Horn Mine; if a mill is built there, it could process Big Horn Mine ore, ore from the Hidden Hill Mine, and gold-bearing dumps at the Big Horn, Hidden Hill, and Buena Vista Mines and the Midas Touch Prospect. All of these resources are adjacent to the WSA; however, their development would increase likelihood for development of resources in the WSA. Two major fault zones (the Hidden Hill, and the Big Horn) appear to have controlled the mineralization at many of the prospects and mines. All of the prospects or mines with vein-type occurrences and resources are on or adjacent to one of these fault zones. Veins throughout the eastern half of the WSA contain various amounts of gold, silver, and copper; only veins near the Big Horn Mine and in the northeastern corner of the WSA contain lead. Some veins are as thick as 6 ft, are traceable intermittently for over 2 mi along strike, are sporadically mineralized, are encased in prophylitic, argillic, and phyllic altered host rock, contain pyrite, chalcopyrite, galena, specularite, barite, or fluorite, and display multiple stages of quartz veining and (or) brecciation. Sample analyses at five prospects (map nos. 3, 18, 23, 24, and 31) indicate they may have disseminated gold resources. To date no oil or gas has been discovered within the WSA. However, some oil and gas leases are currently (August 1982) held within this study area.

Jan 1, 1984

As fulfillment of the requirements of Contract H0387019 for the United States Department of the Interior, Bureau of Mines, a complete field kit, for performing on-site determinations of individual employee Time Weighted Average (TWA) exposures to nitrogen dioxide (NO2) and nitric oxide (NO), has been developed by MDA Scientific, Inc. This report provides background information and experimental data validating the use of this kit with confidence to ? 10 percent accuracy.

Jan 1, 1981

By N. S. Dalal, V. Castranova, K. Van Dyke, V. Vallyathan, J. H. Kang

"We have reported previously that crushing or grinding crystalline silica results in the generation of silica-based radicals on the particulate surface and that these radicals can generate hydroxyl radicals in aqueous solution. Data in the present study indicate that freshly ground silica is more cytotoxic and is a more potent activator of alveolar macrophages than comparably sized aged silica. That is, compared to aged silica, fresh silica is 4.2-fold more potent in decreasing the membrane integrity of macro· phages; is 50% more potent in activating hydrogen peroxide secretion by macro· phages; and is 4.frfold more potent in stimulating cellular chemiluminescence. Prosil 28, an organosilane material, is an effective coating agent for fresh silica. It decreases the cytotoxicity of fresh silica by as much as 78% and decreases the ability of fresh silica to induce chemiluminescence from alveolar macrophages by 58%. The data suggest that surface radicals associated with freshly cleaved dust may be an important factor in the induction of pulmonary disease. Furthermore, treating dust with coating agents may substantially decrease toxicity. INTRODUCTIONThe U.S. Department of Labor estimates that over 1.25 million American workers may be exposed to crystalline silica and that nearly 60,000 may be at risk of developing some degree of occupational lung disease (Parkes, 1982; Peters, 1986). Occupations of concern include miners, stone quarry workers, sand and gravel workers, sandblasters, foundry workers, and glass workers. Acute silicosis is characterized by inflammation, alveolar lipoproteinosis, and the rapid development of respiratory disability (Banks, 1986). In contrast, chronic silicosis develops 20-40 yr after initial exposure and is characterized by the appearance of concentric hyalinized nodular lesions and the progressive development of dyspnea (Parkes, 1982; Ziskind et al., 1976)."

Mar 1, 1992

By S. H. Ash

The Pennsylvania anthracite region is composed of four fields, namely, the Northern, Eastern Middle, Western Middle, and Southern. It is in the eastern part of Pennsylvania and is shown on figure 1. The anthracite industry is confronted with a crucial problem of inundation by water impounded in underground pools in many mines and by infiltration of water from streams and pools on the surface (3). The deposits of anthracite in the United States are limited virtually to Pennsylvania, and the difficulties of this industry have been commonly considered as a State problem rather than a national one (1, 4, 6, 7). Anthracite was discovered in Pennsylvania in 1762, and the first mining company was formed in 1793. It was not until 1812 that anthracite began to receive recognition in the Philadelphia market as a domestic fuel, and by 1838 the annual production was nearly 1 million net tons. Since anthracite mining began, mine water has become progressively more difficult and costly to handle because of the extraction of anthracite both underground and along the outcrops of the beds, until at the present time mine drainage is a major anthracite-mining problem. Mine water is handled at the anthracite mines as follows: (a) by pumping, (b) by drainage tunnels, (c) by combination of pumping and drainage tunnels, and (d) by water hoists (hoisting water by means of large buckets) (4, 5,6, 7). This paper covers removal of the water from mines by means of pumping plants. Pumping is indispensable in the production of anthracite (5). The cost of pumping mine water has increased progressively since anthracite mining began. Some collieries have been forced to discontinue mining because of the high cost of pumping.

Jan 1, 1950

By Xintan Chang

MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under the influence of natural ventilation, fans, fires, or any combination of these. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influences (varying outside temperatures), and internal influences (fires). Extensive output enables detailed, quantitative analysis of the effects that the alteration will cause to the ventilation system. The program was developed at Michigan Technological University (MTU), Houghton, MI, with support from the Bureau of Mines. A personal computer (PC) version of the program was completed under contract for the Bureau by MTU. The purpose of this report is to document the installation and use of the PC version of the program MFIRE.

Jan 1, 1990

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977