Search Documents

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations wi.thin a multiple-seam configuration. At two mine sites where such ground interactions were present, the Bureau performed a complete geological analysis and installed and monitored instrumentation to gather pertinent data on rock mechanics. Overburden depth varied dramatically in the vicinity of the study area and reached a maximum at the study site; innerburden thick-ness was less than a pillar width (40 to 4S ft); heaving was experienced in both mines where sandstone and/or shale floor units were observed; overlays of the mine layouts show pillars were not totally superpositioned; a maximum of S in of roof to floor convergence was measured; and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig over instrument setting pressure.

Jan 1, 1987

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the sixth. The data are accompanied by maps showing the loca.ion of holes, drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test geophysical anomalies. The locations of those holes are shown on figure 13 in Volume I. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By S. M. Marshall

The investigations recorded in this bulletin were conducted by the Pacific Coke & Coal Co. in cooperation with the United States Bureau of Mines and the University of Washington. They cover one phase of a comprehensive investigation to determine whether coals from an extensive, undeveloped area of Pierce County, Wash., can be used in the manufacture of coke for the iron blast furnace. The completed investigation had three parts: (1) A geological survey of the coal property, (2) washing and crushing tests of the coals, and (3) coking and by-product tests. The geological survey, which was not conducted in cooperation with the Bureau of Mines and the University of Washington, included systematic tracing of the coal beds by test holes throughout the property, except some portions covered by an impenetrable layer of glacial drift. By this means all of the beds were correlated, their thickness and general character were determined, and tonnage estimates were made. Only such parts of the survey results as are necessary to a full explanation of the investigations described herein are included in this bulletin.

Jan 1, 1931

By Frederick C. Trutt

This report is intended as a reference for personnel interested in the computer anlaysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures described include the Newton-Raphson iterative technique for the analysis of normal operation as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults. During program development, strict attention has been given to the inclusion of core and/or time saving techniques such that these algorithms may be implemented on small as well as large computers. Program languages include FORTRAN IV for batch processing applications and APL or BASIC for interactive applications.

Jan 1, 1981

By Duvall Wilbur I.

This is the second report to be presented on th application of stress analysis to underground Mining problems. In part I2/ of this investigation the stress distribution around single openings in unidirectional and hydrostatic stress fields was analyzed. Relationships between maximum stress concentration and size and shape of openings were determined by the photoelastic method. In most cases the results were verified by mathematical methods This report considers the stress distribution in pillars formed by two or more openings in a. unidirectional stress field. Relationships between stress concentrations and size and shape of pillars are developed. Applied to mining, results snow how estimates may be made of the stress distribution in pillars, what factors cause high local stresses, and how local stress concentrations may be reduced by proper design of mine openings. The photoelastic method was used, as in Part I, to study the stress distributions, and, whenever possible, the results were verified mathematically. A description of the photoelastic method and equipment is .given in Part I.

Jan 1, 1948

By Anthony D. Szpak

The purpose of this program was to demonstrate the feasibility of Illuminating various types of underground coal mining machinery as required by the Federal Coal Mine Illumination Standards Part 75.1719 to 75.1719-4 Code of Federal Regulations Title 30. Nine various machines were illuminated and the illumination systems were evaluated for a 3 month period of operation. Factors evaluated were ease of implementation, reliability, ease of maintenance, acceptance by mine workers and operators, Illumination degradation and durability.

Jan 1, 1981

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By Walter C. Woodmansee

The only reported mineral production in 1977 was small output of alluvial gold, valued at an estimated $54,320.2 In addition, marine shells are gathered for use in lime manufacture, although output was not reported. Proposed development of a bauxite mine and smelter, involving Rennell and Vaghena Islands, was deferred in June. Conzinc Riotinto of Australia Ltd. (CRA), in partnership with Mitsui Mining & Smelting Co. Ltd., and the Solomon Government, with- drew from the project, and Mitsui, which conducted a feasibility study and metallurgical testing of the bauxite, decided to defer further work because of slack demand for aluminum in Japan and difficulties in arranging financing. The Mitsui feasibility studies reportedly indicated that the project could be viable despite technical difficulties and relatively high initial investment costs. The project was to produce 1.5 million tons of bauxite and 600,000 tons of alumina per year from reserves totaling 60 million tans at 45% to 50% A1203.

Jan 1, 1981

By Jr. Frank Parrish

This report describes the performance of 17 selected water-injection projects producing from Pennsylvanian-and Permian-age reservoirs. Illustrations depict reservoir structure and thickness, and production and injection history. A selected bibliography of publications pertaining to area oil recovery and geology is included. Tabulations of field and reservoir data reveal marked differences in the projects. Increased oil recovery resulted from injecting water in most cases; however, seven projects recovered less oil than the operators anticipated. Oil recovery by water injection ranged from 0.2 to 262 bbl per acre ft, or 0.1 to 22.5 pct of the initial stock-tank oil in place. Major reasons suggested for poor performance include: (1) Adverse directional horizontal permeability, (2) channeling of injected water through fractures or zones of high permeability, and (3) lack of containment of injected water. One 330-foot-deep project is among the first successful shallow water-floods in north Texas. Another project is the first successful Canyon sand-stone waterflood reported in the area. Previous gas injection in two Cisco sandstone projects did not prevent the reservoirs from responding favorably to waterflooding.

Jan 1, 1965

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By J. C. Franklin

A data-acquisition system was designed by the Bureau of Mines to monitor five detectors with radon continuously flowing through each. These detectors could be monitored up to 12 times an hour, but were only monitored according to a preset time, thus allowing radon to be monitored continuously in a uranium mine. The counter can be set to monitor each detector for any period of time up to 16.5 minutes. This allows very low concentrations to be monitored longer to reduce statistical error. There would be no upper limit in radon concentration that could be monitored, but there would be a lower limit of 50 picocuries per liter (pCi/l). Each detector was cylibrated in the laboratory by the Lucas flask method. Multiple samples were taken at two different concentrations, and the correction factor for each detector was determined by a least squares fit of the data. To verify the calibrations, a series of measurements at several concentrations were made against a constant source. Our agreement at low radon concentrations (300 pCi/i) with the two-filter method as within 3 percent; thus, the total error would be this difference plus the two-filter error. At high concentrations the coefficient of variation ranged between 2.1 and 9.8 percent for the five different detector units.

Jan 1, 1976

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By Terry R. Neumann

In 1989, the Bureau of Mines conducted a mineral resource investigation of the 52,350-acre Jersey Jack study area, located in the Clearwater Mountains of north-central Idaho. Twenty-eight mines and prospects were examined, and 483 rock, placer, and petrographic samples were collected during the field study. Two properties contain gold resources; mining company data show the Robinson Dike mine contains an estimated 940,000 tons of "drill proven and probable reserves" averaging 0.041 oz/ton gold, and the Bureau of Mines investigation showed the Blacksand placer mine contains an estimated 64,000 cubic yards of identified placer resources averaging $8.13 in gold per cubic yard. Sample analyses from other properties indicate that gold resources are likely to exist; however the low tonnage, narrow, fissure-vein type deposits would require mining by relatively high-cost underground methods and would be subeconomic at a gold price of $400/oz.

Jan 1, 1991

By William N. Patterson

This report describes the design and testing of an improved quiet hard rock percussion drill. The improved drill incorporates a tappetless design with independent rotation in a hand held drill weighing 50 lbm. Laboratory and field testing in three mines were conducted. The testing showed improved drilling performance with no increase in measured noise levels over the fist design.

Jan 1, 1985

By W. T. Millar

Field reconnaissance and laboratory tests an clay from South Windsor, Hartford County, Conn., indicate that the clay is suitable for lightweight aggregate raw material. Exploration of the deposit supports the conclusion that the reserves of clay are sufficient for economical mining operations to produce lightweight aggregate. Preliminary tests indicated that the clay has a short bloating range. Initial expansion occurred at 2,000° F, and at 2,100° F the clay was slightly overfired and sticky. Rotary kiln tests verified the preliminary data, and these tests showed that the clay would make a good lightweight aggregate if the processing temperature and the kiln feed sizes were closely controlled. Lightweight concrete made from the processed aggregate had properties comparable to those of concrete made from a commercial clay aggregate.

Jan 1, 1964

By Chas. F. Jackson

During the past year a special study was made of shrinkage stoping A large number of mines in the United States and Canada which employ this method were visited and their practices were discussed with the operating staffs. The operating data obtained are appended hereto. Data were also abstracted from the literature on other mines and are combined in tables with data personally secured by the author. References are made to these published articles, some of which have appeared as information circulars of the United States Bureau of Mines, in the Transactions of the American Institute of Mining and Metallurgical Engineers, and the Engineering and Mining Journal. Several of the mines referred to which have not been described in individual papers will be described in detail in information circulars to be issued by the bureau. Eventually it is planned to combine and condense the information in these circulars and present the data in bulletin form.

Jan 1, 1930