Search Documents

[1.1. The provisions of this code are minimum provisions and are designed to minimize hazards to life and property in and about underground coal mines where electrical equipment and circuits installed used. They indicate the Steps necessary in the selection, installation, operation, inspection, and maintenance of electrical equipment and circuits to obtain proper safeguards in reducing electric shock, fire, explosion and other hazards. Surface as well as underground installations were considered in formulating the code and, unless otherwise stated, each provision applies equal to both underground and surface installations. This code does not apply to buildings and installations not directly connected with mining operations, nor does apply to strip-mining operations.]

Jan 1, 1952

By D. G. Foot

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2 pct K20, and recoveries from 84 to 99 pct. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97 pct of the potash in a concentrate containing 54.3 to 60.3 pct K20. Fatty acid flotation of the high-sulfate evaporite recovered 78 pct of the sulfate minerals in a 27.8-pct-K20 concentrate. Flotation of the chloride minerals with amine collector recovered 80 pct of the potash in a 59.7-pct-K20 concentrate. Solar evaporation of 10,000 gal of brine recovered 99 pct of the potash in a crude evaporite containing 24.5 pct schoenite and 20 pct sylvite. Continuous flotation in a 100-lb/h process research unit recovered over 95 pct of the potash in schoenite and sylvite concentrates containing 28.0 and 62.3 pct K20, respectively. An economic evaluation suggested a rate of return of 3 pct for a new facility and 9 pct if. the process is adapted to fit an existing plant.

Jan 1, 1984

By L. A. Morely

Volume II of the final report concerns the application of sensitive ground-fault interrupters (GFIs) to ac utilization circuits in U.S. mines The main concepts examined are shock prevention and methods for reducing nuisance tripping. The research involved a literature search, input from previous Bureau of Mines contracts, and contacts with electrical manufac-turers and mining personnel. Following this background work, several devices that showed promise were obtained and tested. Results of testing indicate the existence of GFIs that may be modified to perform adequately on U.S. mining systems. A recommended set of guidelines is included in the report, covering design, construction specifications, and performance tests.

Jan 1, 1982

By L. R. Stark

Two wetland simulation experiments were carried out in order to determine the effects on manganese retention of several wetland design parameters, including flow rate, inlet pH, carbon supplementation, substrate type, and surface free water depth. The primary aim in each experiment was to determine if sustained manganese retention could be accomplished under the specific experimental treatments. If successful, these experiments could recommend design parameters for the construction of field wetland systems for manganese treatment. Crushed limestone clearly was superior to spent mushroom compost with respect to manganese retention. The presence of free surface water detracted from manganese treatment, while lower flow rates enhanced manganese treatment. Sustained manganese retention was achieved using crushed limestone as the substrate coupled with an absence of surface free water, under inlet water conditions of pH 7.0 and no appreciable iron. Sustained manganese retention was not achieved under reducing conditions using spent mushroom compost while varying flow rate, inlet pH, and carbon supplementation regimes. However, lowering the flow rate resulted in many significant beneficial effects on outlet water chemistry: lower outlet manganese concentrations (over the short term), higher outlet pH, lower outlet acidity, higher outlet alkalinity, higher outlet sulfide, lower outlet sulfate, and lower outlet redox potential. Supplementation of the wetlands with dairy whey resulted in lower outlet manganese concentrations (over the short term), marginally higher outlet sulfide levels, and acted to lower the redox potential under the high flow regime. Wetlands receiving a neutral pH had lower outlet acidity, higher outlet alkalinity, lower outlet sulfate, but equivalent outlet manganese concentrations than wetlands receiving an acidic pH. When manganese is the primary mine water contaminant and a passive water treatment system is to be used, it is recommended that crushed limestone with negligible surface water be used in place of composted materials. This recommendation assumes a source water with circumneutral pH and an absence of other metals.

Jan 1, 1993

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson. Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001.000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,471,000 tons under less than 60 feet of cover.

Jan 1, 1966

By W. L. Cornell

The Missouri lead ores are the only domestic sources of cobalt presently being mined and processed for other materials. They represent the best short-term solution for meeting up to 13 pct of the Nation's strategic and critical cobalt needs from domestic sources. Presently, the cobalt is lost as an impurity in the copper, lead, and zinc concentrates and in the mill tailings because the technology to recover it with minium impact on present production does not exist. This paper presents results of research, built upon earlier Bureau of Mines laboratory research, to enumerate the problems encountered in cobalt recovery from the copper concentrate under actual mill conditions; to present alternative solutions to these problems; and finally, to describe the best available technology for cobalt recovery within the imposed constraints. Mineralogical analyses showed the cobalt present as a distinct mineral phase, predominately siegenite, amenable to a physical separation method such as froth flotation. Flotation was chosen for recovery because of easy adaptation by the mills. Unit processes of grinding, conditioning, and flotation were studied individually and in concert, and a series of continuous tests were run based on the parameters developed to obtain engineering data for subsequent economic analysis. Overall cobalt grades of 3.00 wt pct at a recovery of 64.0 pct were achieved.

Jan 1, 1987

By J. S. Coffman

Wyoming is estimated to have more than 700 million tons and Utah more than 2.5 billion tons of +10 percent P2O6 phosphate rock considered to have some future economic potential. In Wyoming, the +24 and +18 percent P205 rock potential resources total nearly 250 and 450 million tons, respectively. In Utah, the +31, +24, and +18 percent rock total approximately 33 million, 222 million, and 2.2 billion tons, respectively. These resources are all located above the local drainage levels and do not include latent resources. All of the mining and beneficiation of phosphate rock in the two States is done by San Francisco Chemical Co. The facilities include open pit mines at Vernal, Utah, and Leefe, Wyo.; an underground mine in the Crawford Mountains, Utah, and beneficiation plants at Leefe and Vernal. One of the principal markets for the phosphate rock is Western Phosphates, Inc., fertilizer plant at Garfield, Utah. Recent exploration and development has been under-taken by different companies in the Southeastern Wind River Range, Sublette Range, and Crawford Mountains. The facilities at Leefe and Vernal are in the process of expansion. Some of the areas of western Wyoming contain vast quantities of phosphate rock in minable units, but, because of their remote location, are classed as latent areas. In these areas, there are estimated to be about 700 million, 2 billion, and 3 billion tons of phosphate rock in the +24, +18, and +10 percent P205 grade classes, respectively. The Snake River Range of Idaho and Wyoming is also estimated to contain roughly 21, 106, 177, and 214 million tons of potential resources in the +31, +24, +18, and +10 grade categories, respectively. This area also contains a large amount of latent rock in the more remote areas.

Jan 1, 1967

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By F. D. Stevenson

A metal diaphragm pressure relay system was constructed to measure vapor pressures of the metal halides, oxyhalides, and other substances at temperatures up to 700° or 800° C. The vapor pressure of arsenic (III) oxide (As2O3) was determined to verify the reliability of the apparatus for such measurements. The data for the liquid AS2 Os (2820 to 4830 C) are represented by the equation, log Pmm = 6.875 - 2,929/T, from which the normal boiling point was calculated to be 461° C. The heat of vaporization calculated from this equation was 13.40 ±0.09 kcal/g mole As4OS and is essentially constant over the interval studied. The melting point of the octahedral arsenic (III) oxide was determined to be 278° C from the inter-section of the solid and liquid vapor pressure curves, A thermal analysis apparatus is also described by which melting and transition temperatures could be checked by a method independent of vapor pressure data. The melting points of the monoclinic and octahedral forms were determined to be 314.4 ±1.4° C and 278 ±5° C, respectively.

Jan 1, 1963

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By James J. Dowd

The investigation to evaluate the reserves of coking coal is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coal and coal blends not now widely used for metallurgical coke making. This is the tenth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Knott County, Ky., which comprises parts of the Salyersville, Prestonsburg, Troublesome, Hindman, Pikeville, Cornettsville, and Whitesburg quadrangles. (See fig. 1.) A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds up to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick. These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and category, mined-out areas, areas excluded from the estimate but which may contain reserves based only on geologic inference, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By J. F. Barkley

Smoke abatement is a subject of which fuel technology, although absolutely essential, is only a part. Its successful accomplishment starts and ends with human factors that must be given thorough consideration; between this "start" and "end" fuel technology is applied. Smoke abatement usually starts from the desire of some person or persons to be free from uncleanness caused by the stack of someone else and ends with the sincere desire of the operator of the fuel-burning equipment to maintain a clear stack. Although "smoke abatement been discussed for many years, it is only recently that the public has been mindful of such expressions as "air pollution" and "air hygiene." The subject has duel in common with that of supplying pure water but is more complicated. The public desires pure water, expects pure water, is willing to pay for pure water, and expects to continue to pay for it indefinitely; it is a development of civilization. It is doubtless correct to say, however, that people in general do not et realize the detriment of air pollution to their well-being or give the question enough serious consideration. This is illustrated by the fact that in city smoke abatement it is the mass of small householders that sins the most and is the hardest to handle. It is rather difficult to assemble a group of people in a room without the air becoming contaminated with smoke. Smoke abatement will lag with the lack of desire for pure air - probably the biggest human factor involved in its accomplishment.

Jan 1, 1939

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electrokinetic dewatering and consolidation of metal-mine tailings. Tailings were placed in 0.3-cubic-foot Plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Dewatered material was tested for moisture content and density. Equipment and procedures were developed to optimize the method for unclassified mill tailings from a particular mine in the Coeur d'Alene, Idaho, district. Results indicate the method to be highly effective in dewatering and consolidating this material.

Jan 1, 1974

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

By B. J. Moore

This publication contains analyses and related source data for 310 natural gas samples from wells and pipelines in 16 States. All of the samples were obtained and analyzed during calendar year 1978 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis appara¬tus, which are described in Bureau of Mines Bulletins 4862/ and 576.3/ The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Twenty previous publications have presented the results of 11,573 gas analyses made prior to 197R. The first three, Bulletins 486,4/ 576,5/ and 617,6/ contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 17

Jan 1, 1979

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By H. Miller

In recognition of the need for a portable low-profile hard rock crusher, the Bureau of Mines sponsored the development of such a unit capable of moving up as the face advances. By allowing primary ore reduction at or near the mine face, the advantages of conveyor haulage From the face as demonstrated in soft ore and coal mines, could be realized for hard rock Brines as well. This report presents the results of a development and testing program for such a portable low-profile crusher, designed by Eagle Crusher Company and called the M44. The unit has an extremely low vertical profile considering its size and capacity. The crushing jaws, which form the crushing lumber, are inclined, with the lower jaw mounted for eccentric movement relative to the stationary upper jaw. This provides efficient crushing while also forcing material through the crushing chamber. As a result, the inlet feeder can be disposed horizontally. To facilitate correct processing of different materials, the size of the discharge opening and the action of the movable crushing jaw are variable. The unit also incorporates a feeder hopper and discharge conveyor that provides for efficient ore handling through the machine. Tests demonstrated the M44 Crusher&apos;s high capacity, efficiency and reliability. During testing, it crushed over 120,000 tons of materials of up to 32,000 psi compressive strength at production rates in the 200-350 tons/hour range. The unit operated smoothly under simulated low-headroom conditions, and Proved readily transportable.

Jan 1, 1983

By P. L. Woolf

Three trials with oxygen-enriched unheated blast air are described. The trials were conducted in the Bureau of Mines experimental blast furnace located in Bruceton, PA. The first trial utilized moisture addition to the oxygenated blast. The second and third trial were conducted with natural gas injection. The test was basically a feasibility study and in that regard the practice was demonstrated to be feasible and also have possible advantages over hot blast operation. The testwork was conducted in 1964 and 1965 as part of a continuing study of iron making technology in cooperation with several North American Steel Companies.

Jan 1, 1985

By G. M. Kintz

From 1895 to 1932, inclusive, 1,0163/ men were killed in and about New Mexico coal mines. Of these, 473 (approximately 47 percent) were killed in the 17 explosions listed in this paper. The second largest explosion of record in the United States, in so far as fatalities are concerned, occurred in New Mexico. The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the State inspector of coal mines of New Mexico. The tables included are complete only with regard to major disasters. The Bureau of Mines considers as a major disaster one in which 5 or more men are killed. A few minor disasters are included, however.

Jan 1, 1934