Search Documents

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By Mary E. Cocklan-Vendl

Regulatory processes associated with development of major mining operations in Alaska and British columbia were evaluated using specific case studies. Included were one hard rock mine in Alaska (Red Dog Mine), one hard rock mine In British Columbia (Snip Mine), and one offshore gold dredging project in Alaska (WestGold SIMA). Based on a comparison of the three case studies, it became clear that the primary incentives for cost effective permitting are: 1) early and continuing coordination of proposed project plans, designs and schedules with key regulatory agencies and local area residents and 2) development of a sufficient level of baseline information on air quality, water quality, wetlands, endangered species, fish and wildlife, and socia-cultural conditions to support the required permit application. The U.S. permitting process worked in much the same way as the Canadian permitting process. Disincentives of mine permitting include high initial costs for baseline data gathering. However, a relatively high early investment resulted in more efficient permit acquisition and reduced long-term monitoring requirements. A common problem Identified was the inadequate supply of trained agency personnel with the requisite technical and permitting experience. This sometimes resulted in poor decisions and unnecessary changes in project plans and schedules.

Jan 1, 1993

By J. A. Bartol

A survey was made of accident data and operating practices related to overloading and uneven load distribution on haulage trucks in noncoal open pit mines. Safety and economic aspects were analyzed. A bibliography of the literature was prepared. Review was made of available or projected systems for weighing or load indicating that might be applied to haulage trucks. A model specification was prepared for an overload detection system. Several promising systems for overload detection were identified. One was installed and tested briefly in a 170-ton rear dump truck in a copper surface mine.

Jan 1, 1982

By Louis A. Panek

The practice of roof bolting or rock bolting to stabilize rock surrounding underground excavations has increased tremendously within a few years. This widespread application has led to many questions concerning the mechanics of bolting and has pointed up the need for a quantitative method of designing bolting systems. To answer these questions a research program was initiated to determine the principles of roof bolting. The first problem chosen for investigation was the use of bolts to reinforce bedded roof, since the great majority of bolts are used under these conditions. The attack employed is a combination of theoretical and experimental stress analysis. Centrifugal testing of models was chosen as the experimental method because it is particularly suited to the study of stratified roof. This report describes the models, the experimental method, and the model-prototype relations. By using dimensional analysis, a general expression for a roof-bolting design formula in terms of the structural variables has been obtained. Certain model-prototype similarity requirements have been relaxed, thereby minimizing the number of variables to be studied and extending the applicability of quantitative test data to a large class of full size structures.

Jan 1, 1956

By Stephan Stecura

One of the principal objectives of the Bureau of Mines program for development of superrefractory ceramic materials is to obtain fundamental data on the physical properties of refractory oxides. Elements of particular interest to research workers in the Bureau include groups III and IV of the Periodic Table and the rare-earth group. This report contains thermal expansion and phase inversion measurements on oxides of scandium, yttrium, lanthanum and 12 lanthanide series elements (promethium and terbium omitted) up to 1,350°C, made by high-temperature X-ray diffractometer techniques. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures; with anisotropic oxides expansion was determined parallel to each major crystallographic axis. The combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C, and approximately 2 percent at 1,000° C, No difference in expansion coefficients was observed between heating and cooling cycles for oxides that did not undergo phase inversion. Tabular data of linear expansion, in percent, linear expansion coefficients, and graphical presentation of linear expansion as a function of temperature are presented.

Jan 1, 1961

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By E. D. Calvert

The objective of this research was to examine variations in melting and forging practice for four titanium-base alloys and to determine their effect on the resultant product. Of particular interest was the evaluation of the skull-casting technique. The data should serve as a guide to producers and consumers of titanium products. Physical properties of four titanium-base alloys in ingot form and in sheet form were evaluated and correlated, where possible, with variations in the melting and casting procedure. Consumable-electrode melting was used throughout, but arc current and furnace backfill pressure were varied, and ingots were formed both by melting directly into a water-cooled copper mold and by skull melting followed by pouring into a graphite mold. Alloying metal additions for the alloys tested were (1) 8 percent manganese, (2) 6 percent aluminum and 4 percent vanadium, (3) 6 percent molybdenum and 2 percent aluminum, and (4) 16 percent vanadium and 2.8 percent aluminum.

Jan 1, 1962

An underground mine disaster is an accident of major proportions that takes a significant toll in human lives. A disaster usually disrupts the normal functioning of a mine and may result in entrapment of miners whose normal egress from the mine is cut off. A disaster often necessitates a rescue operation and a means of keeping the trapped miners alive while they await rescue. Explosion, fire, inundation of water or toxic gases, and collapse of a major portion of a mine are among the causes of mine disasters. Miners threatened by such an occurence must either bring the situation under control (e.g., by extinguishing a fire) or remove themselves from the danger. If control is unsuccessful, they must retreat to a place of safety. Four different activities may be involved: evacuation, escape, survival, and rescue. Evacuation is the orderly exit of people from the mine using previously identified escapeways and following a previously determined evacuation plan. Miners whose normal evacuation routes are blocked may be able to find alternative exit routes and escape by their own efforts. For those who cannot, the issue becomes survival while waiting to be rescued. The survival period may last for many days while rescue efforts are mounted from outside the mine.

Jan 1, 1981

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By Daniel G. Di Canio

Reference information and user instructions for Version 3.0 of the Accident Cost Indicator Model (ACIM) software package are presented. ACIM estimates the tangible costs of occupational injuries, illnesses, and fatalities in the United States mining industry.

Jan 1, 1983

By George A. Savanick

Coal mine roof shales fracture preferentially at slickensided surfaces because of weak or nonexistent adhesion between two slickensided rock surfaces. The purpose of this Bureau of Mines research was to characterize chemically the thin film of smooth, glossy material that makes up the slickenside. This material was analyzed by electron spectroscopy and ion scattering spectrometry while in place on the rock surface and by standard methods of quantitative chemical analysis on concentrate removed from the rock. These analyses showed that the chemistry and mineralogy of the slickensides are similar to that of the adjacent shale.

Jan 1, 1974

By M. P. Ristenbatt

A new automated post-disaster signaling system, intended to use through-the-earth EM propagation, was demonstrated in the laboratory at an input SNR of -34 dB. The system presently available requires an input SNR of +6 dB, and uses a human-ear detector. The work here demonstrated coherent integration, for the automated system, in multiples of 17 s, up to 1088 s (18 minutes). A repeating pseudorandom (or pseudonoise) signal is used, which offers an ideal auto-correlation at the receiver matched-filter output. A novel decision-variable algorithm achieves the estimate of noise level by using those matched-filter output samples that occur between the signal auto-correlation peaks. This work included corraboration that the received signal power decreases as distance to the tenth power, for through-the-earth propagation. Thus, the above 40 dB reduction in required input SNR permits an automated system to have a range 2.5 times that of the present system. In addition, an automated system permits the possibility of operating receivers around-the-clock; this would reduce the initial-detection-time from a few hours (present system deployment time) to a few minutes (signal processing time).

Jan 1, 1981

By Michael A. Trevits

Since the promulgation of the MINER Act and the follow-up changes to the regulations governing mine seal construction and maintenance, mine operators must be acutely aware of the atmosphere in sealed mine areas and prepared to deploy control technologies when the conditions are warranted. On Site Gas Systems1 in Newington, Connecticut was awarded a contract by the National Institute for Occupational Safety and Health (NIOSH) to construct a novel in-mine nitrogen (N2) generation plant using pressure swing adsorption (PSA) technology. PSA technology utilizes carbon molecular sieve material and pressure to adsorb oxygen (O2) molecules while allowing N2 molecules to pass through the sieve material. The prototype PSA unit was tested at the NIOSH Safety Research Coal Mine (SRCM) where a 62,000 ft3 area of the mine was rendered inert during a series of two tests. The resultant data were then used to construct a CFD simulation of both injection tests. In addition, O2 depletion and gas leakage rates were quantified in the model and were compared to actual values. Once the model was calibrated, the sealed mine area was doubled and simulations were made with various injection rates and injection site locations to determine the impact on the time needed to render this area inert. This paper presents an overview of the PSA plant, the details of the gas injection tests and CFD modeling work.

Jan 1, 2010

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted the Bureau's Mount 'Weather Testing Adit,Mount Weather, The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Revelle, mining-engineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gavel valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By Michael Rieber

An analysis of coal slurry pipelines was presented in our May 1976 study, Route Specific Cost Comparisons: Unit Trains, Coal Slurry Pipelines and Extra High Voltage Transmission (4]. The present study extends that analysis. The earlier work included technical and economic cost descriptions of the black Mesa and ETSI pipelines as well as some hypothetical pipeline routes. Water problems, safety and environment, required resources, and labor impacts were discussed at some length. Additionally, pipeline impacts on competing railroads, slurry-rail comparisons, and cost escalation. were analyzed. The difference in pipeline profitability to an owner-operator versus a promoter-builder was suggested. These aspects are not redone in this study. Here, we present a synopsis of the previous results and a general statement of coal slurry pipelines. Extensions of the arguments are presented where they appear warranted. New material is developed in the area of pipeline branching and tapping. This would appear necessary if slurry pipelines are to function as more than private lines; if they are, for example, to be responsive to common carrier requirements.

Jan 1, 1977