Search Documents

By J. M. Gomes

Bench-scale flotation tests were conducted on two western tactite ores to study the recovery of tungsten and zinc minerals. The investigation, which is part of the Bureau of Mines ongoing program to develop methods for beneficiating minerals and metals from domestic low-grade ores, demonstrated the feasibility of producing scheelite, sphalerite, and their bulk concentrates. Sphalerite concentrates containing 51 to 53 pet Zn and less than 0.11 pct W03 were selectively recovered prior to scheelite flotation. Zinc recovery ranged from 85 to 91 pct. Scheelite concentrates containing 17 to 25 pct W03 were then recovered from the ore; tungsten recoveries ranged from 88 to 94 pct. Bulk flotation concentrates containing 84 to 91 pct of the W03 and 87 to 95 pct of the zinc also were prepared. More than 98 pct of the W03 in a bulk concentrate containing 9 pct W03 was extracted by autoclave leaching with a soda solution. The zinc remained in the leached residue.

Jan 1, 1982

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control of anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/. These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the mounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating beers dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By H. C. Miller

Several agencies of the Federal Government are engaged in research and fact finding relative to petroleum and natural gas, and others are concerned with carrying out the provisions of specific laws that affect these natural resources in their broad aspects. The Bureau of Mines, however, is the only Federal agency designated by law to engage in research in oil and natures gas production, chemistry, refining, and

Jan 1, 1941

By S. J. Davenport

The increased consumption and importation of fluorspar and cryolite (1)3/ in recent years, and especially the addition of fluorine compounds to drinking water in the United States, have aroused renewed interest in the properties of such compounds and possible health hazards incident to their use. It has been suggested that the issuance of a revision and elaboration of Information Circular 7311, The Hazards of Hydrogen Fluoride Poisoning in the Mineral and Allied Industries, which hay been out of print for some time, would be opportune. Fluorine minerals have been known since the Middle Ages. Fluorine was isolated in 1886 by Moisson (2).

Jan 1, 1954

By Jerry J. Gray

The utilization of secondary titanium was determined in a study by the Bureau of Mines, and a 10-year statistical table showing supply and distribution patterns is presented in this report. Over the total 10-year period, estimated scrap consumption is larger than estimated scrap supply. Trends from the estimated data indicate that titanium is in short supply and probably will continue to be in the future. Because of higher processing costs for recycle scrap, scrap will tend to migrate to the steel and aluminum industries and to ferrotitanium production and exports. Nonrecoverable losses of titanium metal during processing was determined to be a potential area for research.

Jan 1, 1971

By John R. Benham

The West Pioneer RARE II study area, No. 1-006 (fig. 1), has Figure 1.--NEAR HERE a high molybdenum resource potential. Two molybdenum-bearing areas are being explored by Utah International and by Cyprus-Moly Corp, Inc. using geophysical exploration and diamond core drilling. The study area also contains potential resources of gold and silver at six prospects: the Bear Paw (Ibex), Black Bear, Coeur d'Alene, Franklin No. 1, Martin, and Maynard. In addition, the Black Rear and the Martin contain possible copper, lead, and molybdenum resources. Most of the workings are caved.

Jan 1, 1981

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular-price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By M. Clair Smith

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various open-pit mines in the United States. These reports have been prepared in cooperation with various mining companies. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed to improving the efficiency of mining operations. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technological information on mining methods and practices. This report describes exploration, development, equipment, and mining by open-pit methods of the remainder of an ore body that had been previously worked by underground methods. The Tripp pit of the Consolidated Coppermines Corp. is located at Kimberly, Nev., a small mining company town having an elevation of 7,250 feet, 9 miles by road west of Ely, Nev. (fig. 1). The pit extends over the area formerly mined by underground methods from the Morris and Brooks shafts.

Jan 1, 1962

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data oil motor gasolines sold during the minter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular- price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By Murray Weintraub

In an investigation of the incineration of combustible wastes, the Bureau of Mines studied the effect of dimensional parameters, process variables, and fuel properties on the operation of an incinerator that consisted of a single cylindrical combustion chamber in which all combustion air was supplied tangentially above the fuel. Construction and operation of three designs of such a device proved that the tangential overfire air design is effective in providing efficient combustion and low concentration of particulate matter in the effluent gas. A correlation was found that related burning rate with air rate, chamber diameter, and inlet port diameter. In one of the incinerator models, ignition was by radiation from a preheated surface. The temperature of this surface was required to be 1,400° to 1,600° F to insure ignition of moist refuse; however, this had little effect on combustion rates. In the combustion of moist refuse, evaporation of the water proceeded through the fuel bed as a wave, with an ignition wave following the evaporation.

Jan 1, 1967

By Foster Fraas

One of the lithium minerals most widespread in the earth's surface is spodumene (Li2O-A1203-4Si02) a lithium aluminium silicate. For some time, deposits of this mineral were known to exist in the Black Rills of South Dakota, but it was only quite recently that Hess4/ pointed out the great magnitude of the low-grade e deposits it s in North Carolina. The theoretical lithia (Li20) content of spodumene is 8.04 percent. The only other minerals with such high lithia content are the phosphates, but these occur only in pockets and are not in extensive deposits5/. Actually, however, the lithia content in spodumene is never found to be this high, being nearly always below 7 percent for the pure mineral, and part of the lithia is apparently replaced by other alkalies.

Jan 1, 1937

By Robert T. MacMillan

A process has been developed in the laboratory and expanded to semi-pilot-plant scale for recovering titania, iron, and byproducts from two types of titaniferous iron ores. A reducing roast with coke and soda ash followed by grinding and magnetic separation produced powdered iron and slag from which titania and byproducts were recovered by H2SO4 decomposition. Based on the steps tested on a. semi-pilot-plant scale supplemented by the results of the laboratory investigations, enough data are available to make a balanced flow sheet. Combined data from the laboratory and semi-pilot plant indicated that 85 to 9O percent of the titania content of the ore was recoverable and that approximately 90 percent of the iron could be recovered as a metallic-iron powder. Tahawus magnetite from the Maclntyre mine at Tahawus, N. Y., was successfully treated as follows: (1) The ore was roasted at 1,050° to 1,080° C. with carbon and soda ash, thereby reducing the iron to metal sponge and retaining the titania in the slag. (2) The metallic iron was separated, after wet grinding, by magnetic or gravity means. (3) The slag fraction was air-roasted at 850° C. and leached with NaOH to recover Na3VO4. (4) The leached solids received a dilute-H2SO4 leach to remove interfering impurities, chiefly Na2O and SiO2. (5) Titania was dissolved from the leached solids of step (4) by a H2SO4-bake followed by a water leach. (6) Titania was precipitated by seeding and boiling the resulting solution. The spent liquor was used for the dilute-H2SO4 leach in step (4). The following scheme was found to be technically feasible for recovering other byproducts of the process. (1) The gelled filtrate from the dilute-acid leach step was washed and dehydrated to produce a commercially acceptable silica gel. (2) The wash liquor containing sulfates of Na2O, Al2O3, Fe2O3, and TiO2 was combined with the highly alkaline filtrate from the wet-grind and metallic iron-separation steps, precipitating iron and titanium hydroxides, which were separated for special treatment. (3) Anhydrous Na2SO4 and Al2O3?3H2O were recoverable from the alkaline filtrate from step (2) by evaporation and carbonation, respectively, and the barren liquor was recycled to the magnetic-separation step.

Jan 1, 1952

By Ignaz Lichtig

[IN CONNECTION with its work on the conversion of coal to liquid cud gaseous fuels,3 the Bureau of Mines has always striven to keep informed of developments in this and related fields so that unnecessary duplication of effort could be prevented and so that useful ideas, presented in scientific and technical literature, could be evaluated as quickly as possible. Thus the E has compiled expensive literature and patent abstracts on the Fischer-Tropsch synthesis4 and hydrogenation d e venation of coal at elevated h temperatures and pressures.5 6 This publication differs from the references just given in that it covers patent applications, which may or may not have been approved for issuance as a patent, and also includes later material. The patent literature is, of courses, a valuable source for new ideas. German patent, have been particularly useful in this field because both processes for the complete conversion of coal to fluid fuels originated in Germany and were thoroughly investigated there because of the shortage or of indigenous fluid fuels. Among the German literature relating to these processes are patent applications. In contrast to the United States, Germany has a system in which applications are published before the final patents are issued. This arrangement permits the public to view all the applications and not just those for which a patent was granted as is done in the U.S. system. When main of the invention are judged not patentable by the German Patent Office, such documents nevertheless may contain useful ideas for scientists and engineers.]

Jan 1, 1961

By Jasinder S. Jaspal

In underground room-and-pillar mining methods, the sectional conveyor belts are extended or retracted periodically to maintain shuttle car tramming distance to a minimum. A conventional conveyor belt extension or retraction is a heavy, arduous job that if mecahnized, has the potential to improve productivity and safety. To reduce the burden of heavy work of this activity and mechanize it, the Bureau of Mines developed a conveyor belt service machine (CBSM) through a research contract with Tractor MBA. The CBSM is a self-contained, battery-powered, rubber-tired vehicle capable of handling, storing and transporting conveyor belting, wire rope, and associated belt structures in seams as low as 48 in. Belt extensions and retractions are accomplished by moving the tailpiece of a belt conveyor with the CBSM to the next position while dispensing or retrieving the belt, wire rope, and associated belt structures. The CBSM improves the belt extensions and retractions by making them easier and faster, and it utilizes fewer workers. The CBSM was surface tested at the Bureau's Mining Equipment Test Facility (METF) to evaluate its performance and reliability. Modifications were made to the CBSM to correct deficiencies found during surface testing.

Jan 1, 1988

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-l Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949

By S. P. Kinney

The efficient operation of a blast furnace is primarily dependent upon efficient contact between the descending stream of solid materials and the ascending stream of gas. The United States Bureau of dines is conducting a program of research dealing with the interior of the present-day furnace. The work is being carried oat by.(1) observations on commercial furnaces end (2) experiments in the laboratory. Through the courtesy of the officials of the Illinois Steel Co. it was possible to make a detailed investigation of the interior of the shaft of Number.4 furnace at the company's South Works, South Chicago, Ill. The experimental work is to be reported in a U. S. Bureau of Mines bulletin which will include the results of several thousand observations on the interior of the shaft of this furnace. Such of the data as are presented later in this paper constitute only a brief summary.

Jan 1, 1929

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By T. J. Driscoll

Methane-air mixtures can ignite as a result of sparking or rubbing of materials, particularly by impact involving light alloys and rusted steel where an exothermic thermite reaction can occur. This report reviews the published literature and describes a new method utilized by the Bureau of Mines for studying the processes occurring during collisions of light metals with rusted steels. The method involves measuring the spectra of sparks and explosions in methane-air mixtures using a photodiode array. Initial results obtained using magnesium and aluminum alloy 6061-T651 projectiles striking rusted steel are reported. These results indicate that the continuous parts of the spectra show a larger intensity for incendive sparks compared with nonincendive sparks, with the largest relative change in the higher energy, ultraviolet region. An unexpected shift of the intensity maximum for the continuous parts of the spectra towards the infrared region was observed for the more incendive sparks. Evaluation of rusted steel samples with electron microscopy, energy-dispersive X-ray spectrography, and Auger electron spectroscopy after they had been impacted by aluminum alloys indicated that aluminum was transferred to the steel in the form of islands that became larger as a function of increasing projectile velocity.

Jan 1, 1982

By L. B. Pankratz

Thermodynamic data on the elements, oxides, sulfides, halides, and selected hydrides, carbides, nitrides, carbonates, sulfates, silicates, and miscellaneous compounds were reviewed, evaluated, and compiled at the Bureau of Mines. Values for CP°, S°, H° -H°298, ?Hf°, and ?Gf° are given in tabular form. A brief thermodynamic background and a number of examples and applications are presented.

Jan 1, 1984