Search Documents

By John C. MacCartney

In the Pennsylvania anthracite region, the principal source of U.S. anthracite, refuse disposal problems are common since cities and towns are located over the anthracite measures. The Bureau of Mines surveyed refuse banks in the area, determining that 863 banks containing aver 910 million cubic yards of material occupy a total area of about 19 square miles. The vast bulk of the refuse is located within 2 miles of the traffic centers of incorporated c unities which have a total population of 625,000. Twenty-seven banks are burning, causing considerable distress in a number of communities.

Jan 1, 1969

By R. Q. Shotts, H. J. Hager, A. C. Richardson, G. D. Coe

"INTRODUCTION In the State of Alabama few mines produce coal clean enough to be marketed directly without being washed. This is particularly true where the coal is to be used for the production of metallurgical coke. In washing plants where single-compartment jigs alone are used to treat a large range of sizes, it has been found that the washed coal finer than 1/4-inch contains a large proportion of free impurities and is much higher in ash content than are the coarser sizes. To reduce the ash content of this fine material with jigs usually entails a greet reduction in capacity and a loss of coarse coal in the refuse. This investigation, conducted by the Southern Experiment Station of the United States Bureau of Mines in cooperation with the University of Alabama and the Alabama By-Products Corporation, was undertaken to determine whether the fine washed coal from jigs could be economically re-treated on coal washing tables.COALS TESTEDThrough,the cooperation of the Alabama By-Products Corporation, samples of fine-sized washed coal were obtained from their washeries at Bradford and Gamma.The Bradford mine, on the Black Creek bed, yields a low-ash, medium-volatile coal with fairly good coking properties. This coal is blended with coal from the Mary Lee bed for coking purposes and compensates for the high ash content of the latter. The Black Creek bed is about 30 inches thick and seam analyses show an ash content of from 2.0 to 4.0 per cent. In the Bradford mine the undercut is about 6 inches high, so that a large proportion of fines is produced."

Apr 1, 1932

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 8,445 acres of the 20,650-acre Tunnison Mountain Wilderness Study Area in order to evaluate its identified mi nerd 1 resources. The study area is located in Lassen County, CA, about 8 miles northeast from Susanville. No mineral resources were identified in the study area based on literature, field observations, and sample results. No mines were operating in or near the study area in 1985, and no mines, prospects, or claims have been located in or within 1 mi le of the study area. The study area is underlain by Pliocene and Pleistocene volcanic units composed of basalt, andesite, rhyolite, and some pyroclastics. No metallic and only nonmetallic commodities are present in the study area. These included stone and sand and gravel. Although substantial volumes of basalt and andesite (stone) occur within the study area, no identified resources of these commodities were delineated. Sand and gravel is not economic because of small occurrence size and lack of local markets.

Jan 1, 1987

By Forrest T. Moyer

INJURY experience and related employment information are presented in the chapter for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1964. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. All rates in the text are calculated separately on data before rounding, hence component rates may not add to the total rates shown in the tables. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III. COAL Injury experience of the coal mining industry was improved in 1964, as measured by the declines of 1 and 14 percent, respectively, in the frequency and severity rates. Although the total number of injuries increased in 1964, a slightly greater proportional increase in man-hours worked caused the frequency rate to drop to 44.65 per million man-hours. The injury-severity rate in 1964 was 7,832 days lost per million man-hours of exposure. Employment and injury data for 1964 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines. Fatality experience improved significantly with a record low number of 240 deaths in 1964. This total was 44 less than in 1963. The Nation's coal mines during 1964 were free of major disasters (a single accident resulting in the death of five men or more) for the first time since 1956. The

Jan 1, 1965

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129. The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.

Jan 1, 1931

By A. J. Kraemer

This paper is the third and concluding report of the results of the United States Bureau of Mines twenty-third semiannual survey of motor fuel marketed in the United States. The first paper, reporting data relative to gravity, vapor pressure, and distillation range of the samples, was published as Report of Investigations 3129.7 The second report dealt with the data of the twenty-third survey in accordance with the revised specifications for United States Government Motor Gasoline. These data were published as Report of Investigations 3142.8

Jan 1, 1931

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1984 was $409.8 million, and established a new record high for value of nonfuel minerals in the State, at 13.4:% over the previous high of 1983. Output of nearly all nonfuel minerals increased; phosphate rock was one of the exceptions, with no recorded output in 1984. Cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in fire clay and kaolin; fourth in bentonite, ferroalloys, and dimension marble; fifth in masonry cement, lime, and recovered sulfur; and sixth in portland cement. Alabama ranked 22d in the Nation in value of nonfuel minerals produced.

Jan 1, 1986

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By J. A. Eisele, D. J. Bauer, D. E. Shanks

As part of its effort to produce cell - grade alumina from clay , the Bureau of Mines investigated the hydrogen chloride gas - sparging crystallization of aluminum chloride hexahydrate ( ACH ) from aluminum chloride liquor , to provide information for optimizing the crystallization operation . Four parameters important in controlling the crystallization of the aluminum chloride hexahydrate and the concentration of impurities , particularly phosphorus and magnesium , in ACH crystals are ( 1 ) aluminum chloride concentration in the feed solution to crystallization , ( 2 ) hydrogen chloride gas flow rate , ( 3 ) temperature , and ( 4 ) concentration of phosphorus and magnesium also in the feed solution . Parameters 1 , 2 , and 3 affect crystal formation . The combined effects are very important because the phosphorus and magnesium concentrate in the crystals during the early stages of crystal growth . Aluminum chloride hexahydrate of cell -grade purity was crystallized from saturated aluminum chloride solutions containing less than 0.003 wt - pct P205 and 0.010 wt - pct Mg0 . Crystallization temperatures less than 60° C decreased crystal purity .

Jan 1, 1965

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By A. Wahib Khair

"This article first describes the impact of respirable dust on the health of miners in underground coal mines in the United States of America. Second, it identifies the major sources of dust generation, namely cutting tools in the road headings. Two surveys associated with cutting tools were made to determine the useful life of these cutting tools, and to determine the effect of cutting tool wear on productivity of the continuous miners. Third, this article presents the results of a series of experiments carried out in the Rock Mechanics Laboratories at West Virginia University in order to study: 3.1 the effect of cutting tool rate of wear on respirable dust generation, 3.1.1 the effects of rock materials on tool wear and respirable dust generation, 3.1.2 the effect of cutting tool geometric parameters on respirable dust generation, and 3.1.3 the effect of tip materials used in the cutting tool on respirable dust generation. Recommendations in regard to cutting tool design are also presented in this paper.Silica and coal dust are the two major elements affecting the health of underground miners. According to Lemen [1] approximately 1,500 men died due to breathing in silica dust in 1936 while tunneling through a mountain of mostly silica, near the town of Gauley Bridge, West Virginia. Coal dust resulting in lung diseases in one of the major health hazards in underground coal mines. The impact of black lung on miners, coal workers' pneumoconioisis (CWP), has ranged from 16,000 to 23,000 each year since 1982 [1].The trend for conventional mining to continuous machine cutting of coal, using more productive machinery, is inexorable. Intolerable level of dust generated at the face is an indication of inefficient coal/rock cutting by these machines. The federal goverment of the United States paid about 11.7 billion dollars in workmen's compensation to more than 470,000 miners with CWP [2]. Bieniawski and Zipf [3] reported that annual benefit payments were about 2 billion dollars. The enactment of the Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanisms and cutting tool designs.The surveys concerning the utilization of cutting bits and performance of continuous miners in underground coal mines were made in order to have first hand information about bit consumption and coal produ¬ction.Three types of used bits, commonly utilized cutting tools on continuous miners, were collected from different coal mines. The used bits were grouped into symmetrically and asymmetrically worn bits. Distribution analysis for weight loss and conical height loss was done. Details of the results are presented elsewhere [4], here the results are summarized briefly. The analysis shows that approximately 50% of the collected bits have worn asymmetrically, which shows that many bits do not rotate properly during cutting. Analysis of the distribution of bit wear showed that the degree of bit wear varied from one type to another and with mining conditions. On average, the weight loss of the used bits was 4% to 7% with a maximum of 31%. Correspondingly, the loss of the conical height was observed to vary between 11% and 23% with a maximum of 71%. Figure 1 shows typical data associated with some of the used bits."

Jan 1, 1998

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

By John R. Hoskins

The Bureau of Mines conducted an investigation to more exactly define the influence of some end conditions on the laboratory-determined uniaxial compressive strength of rock samples. Limestone, marble, sandstone, and granite were used to provide a range of specimen modulus of elasticity from 2.7 X 106 psi to 10 x 106 psi. Four variables were studied: Nonparallelism and surface texture of specimen ends were the specimen variables investigated; the end platen size and the adjustable or spherical head friction were the machine variables studied. It was concluded that the loading ends of small laboratory models and samples should be prepared with surface irregularities that do not vary from a plane surface by more than 0.001 inch. It was also concluded that nonparallelism of the specimen ends should not exceed 8 minutes for a rigid head load or 15 minutes for an adjusting head load. The measured compressive strength of specimens prepared with these tolerances will be statistically the same with any diameter or thickness of platen and any degree of head friction if initial alinement of the specimen is assured.

Jan 1, 1968

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By Irven A. Jacobson

This literature survey consists of references dealing with gaseous state thermal decomposition reactions of organic nitrogen and sulfur compounds. The reference source for the survey was the Chemical Abstracts from 1930 to 1956, inclusive. Original articles were not studied. The starting date was set at 1930 because previous to this time much of the work is questionable. This report is in three parts: Part I lists nitrogen compounds; Part II, sulfur compounds; and Part III, compounds containing both nitrogen and sulfur. The organization of the classes of compounds is alphabetical: Part I - amides, amines, amino acids, ammonia, azides, azines, azo compounds, heterocyclic nltrogen compounds, hydrazine, nitrates, nitriles, nitrites, nitro compounds and miscellaneous nitrogen compounds; Part II - disulfides, sulfides (including double and triple sulfides), thiols, thiophenes and xanthates; Part III - thioacid amides, thiazoles, thiocyanates and thiuram disulfides. A class formula is included with each class name. The R's used in these class formulas may refer to hydrogen or to the same or different radicals when more than one R appears.

Jan 1, 1960

By Donald F. Reed

In the latter half of 1948 the Bureau of Mines investigated the Magnet Cove Rutile Co.'s prerty in northern Hot Spring County, Ark. This work was supplemental to the work done by the Bureau on the same property in 1945.2/ It was undertaken for the purpose of investigating the extent of the ore body toward the south and west and at depth and to obtain representative samples of the ore for metallurgical tests. For the latter purpose, the samples were so taken as to minimize alteration of the physical characteristics of the ore, these characteristics being determining factors in working out processes of bencficiation. During the investigation, 27 holes were drilled, 10 with a diamond-coro drill end 17 with churn-drill rigs using a Baker standard cable-tool core barrel. Drilling developed an extension of the ore deposit westward from the previously mined area but did not disclose the full depth of mineralization. Metallurgical tests to determine methods of beneficiating the ore and utilizing the resultant products are now in progress.

Dec 1, 1949

By Jr. Denton

This U.S. Bureau of Mines report presents the documentation for HEAPREC, a methodology for calculating reclamation performance bonds for cyanide heap leach operations. HEAPREC is a template developed for use with Lotus 1-2-33 release 2.01 or newer software. The report is presented in step-by-step "user's manual" format. Appendices contain detailed background and reference material on performance bonding, cyanide detoxification regulation, cyanide detoxification methods, general mine reclamation procedures, and an example bond calculation.

Jan 1, 1992

By C. B. Manula

This report is volume 7 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design. Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation," and ventilation. This volume of the final report describes the Rail Haulage subsystem of the Master Design Simulator. This subsystem can be used as a free standing model or can be linked to the Production subsystem to provide rail haulage capability. Complex rail haulage systems can be realistically simulated with this model. This report includes complete instructions for operating the subsystem as well as a program listing. In addition, a case study is included which illustrates the application of the subsystem when linked to the production subsystem.

Jan 1, 1974

The National Institute for Occupational Safety and Health (NIOSH), in partnership with stakeholders in the mining and surface drilling industries, con-ducted research to develop engineering control technologies that reduce workplace noise exposure. The result of this research partnership is the development of a partial cab.

Jan 8, 2007