Search Documents

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By PALMER LARSEN

INDEX TO GEOPHYSICAL ABSTRACTS

May 1, 1931

By Jack I. Paige

In this Bureau of Mines study, two fluidized-bed reactors were designed, built, and operated, one as a sorber for S02 and the other as a contactor for the regeneration of the sulfur-laden alkalized alumina. The target of 90 percent removal of S02 from a flue gas stream containing 0.3 percent S02 was attained by using a sorbent feed of 10-15 grams per minute into a 5-inch bed depth of alkalized alumina. The sorption unit was operated at about 330° C. Complete regeneration of the laden alkalized alumina containing 5 to 10 percent sulfur was accomplished in approximately 1/2 hour. An excess of reformed propane at about 730° C was the regenerating gas. Attrition losses, a major problem with this sorbent, ranged from 0.9 to 7.9 percent of the inventory. Data from these tests demonstrate, within experimental error, the validity of equations developed from short-term, thin-bed tests related to sorption and regeneration rates.

Jan 1, 1970

By Robert W. Geehan

A preliminary examination of the Dayton iron deposit was made in 1941 and 1942 by Paul E. Pesonen and O. H. Metzger, engineers of the Bureau of Nines. Trenching and sampling were recommended, to be followed by core drilling if favorable results were obtained. The Bureau of Mines conducted a project at the property from June to December 1942. The deposit is in sec. 6, T. 17 N., R. 23 E.; sec. 31, T. 18 N., R. 23 E.; sec. 36, T. 18 N., R. 22 E.; and sec. 1, T. 17 N., R. 22 E., M. D. B. & M., about 15 miles west of Lahontan Reservoir in Lyon and Storey Counties, Nev. It lies at an altitude of about 4,500 feet north of the Carson Plains, in the foothill section of mountains that rise to about 7,000 feet to the north of the property. The deposit may be reached by driving 12.5 miles northeast of Dayton over U. S. Highway 50, thence northerly 2.7 miles over a dirt road to the property. The climate is hot and dry in summer, with occasional thunderstorms some of cloudburst variety, and frequent high winds. Winters are usually moderate, with light snowfall and some subfreezing temperature.

Jan 1, 1949

By Michael Rieber

In this study a generalized specification and costing model for high tonnage coal carrying conveyor belts of 3.5 to 100 miles is presented. These belt systems, in modular units or flights, of up to 9 miles in length can be considered in terms of gathering systems. The study format is sufficiently open to allow users to insert their own requirements and parameters. A specific case study is provided. Because conveyor belts are feasible almost anywhere, this study has not investigated any specific route or geographic location. Rather, it has concentrated on setting up an heuristic programming model for conveyor belt facility optimization and cost minimization. The analysis starts with the principle factors involved in the design of the system and their optimization for various cases. This is followed, in Section 5.4, with a factor by factor cost analysis based on industry data and the preceding optimization. The next step is the development of both facility and costing models suitable for computer analysis. Logic flow diagrams are presented at each major analytic step.

Jan 1, 1977

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949

By John F. Papp

The objective of this U.S. Bureau of Mines study is to calculate an accurate, reliable estimate of chromium and nickel content of stainless and heat-resisting steel produced in the United States. The columbium, manganese, molybdenum, titanium, tungsten, and vanadium contents of this steel are also calculated. Such contents are required for estimating the quantity of alloying element recovered from recycled stainless steel and consumed by market sectors. In this investigation, the elemental fraction of stainless and heat-resisting steel was calculated as the ratio of the weight of element contained in stainless steel to the weight of stainless steel produced. The elemental fraction has been calculated as a time-averaged, grade-averaged value. The elemental fraction was averaged from 1962 through 1983, and averaged over the grades for which production was reported by the American Iron and Steel Institute during that time period. The 1962-83 average elemental fraction of U.S.-produced stainless and heat-resisting steel was calculated for chromium to be about 0.17 ± 0.01; columbium, 0.00014 ± 0.00003; manganese, 0.015 ± 0.005; molybdenum, 0.004 ± 0.001; nickel, 0.07 ± 0.01; silicon, 0.009 ± 0.001; titanium, 0.0004 ± 0.0001; tungsten, 0.0001±0.00003; and vanadium, 0.00003±0.0000l.

Jan 1, 1991

By N. S. Petersen

As part of the Demand Evaluation Program of the Bureau of Mines to determine future needs for minerals, a study was instituted to develop and describe a methodology for approaching the problem of substitution between mineral commodities and between mineral commodities and other materials. The report comprises three sections: A review of general factors relative to substitution, a case study of the effect of substitution on zinc die-casting markets in recent years, and a general methodology for reviewing materials substitution with specific emphasis derived from reviewing substitution in the domestic zinc die-casting markets.

Jan 1, 1971

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By C. V. Jude

This U. S. Bureau of Mines (USBM) report presents results of stress analyses and field observations to investigate the effects of elevated trench drifts on the structural stability of rock mass zones surrounding a production draw drift in a mine utilizing a mechanized load-haul-dump (LHD) trench undercut panel caving system. A two-dimensional boundary-element mine stress model was developed to predict the locations and extent of damaged rock mass zones surrounding draw drifts where adjacent, parallel trench drifts are either elevated or not elevated above the LHD production draw drift level. A Mohr-Coulomb shear-failure criterion was obtained directly from in situ borehole shear test data. Hock-Brown shear-failure parameter values were computed from borehole-shear and triaxial test data. A procedure is described to estimate these parameters when a rock mass rating (RMR) value and triaxial data on intact samples exist, and no borehole shear test data exist Results indicate that trench drifts, elevated to the level equal to the height of the LHD production draw drift, would not minimize material damage nor significantly enhance the stability of rib and crown pillar zones surrounding production draw drifts in the mechanized LHD trench undercut caving panel investigated at this mine.

Jan 1, 2010

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By Louis C. Brichta

"The O'Jack Mining Co.'s zinc and lead deposits in Jasper County, Missouri, have been worked intermittently since the early nineties; production from these deposits was greatest during World War I and II - 4,668 tons of zinc and lead concentrates. The deposits are in a sink-hole structure in which intense deformation has taken place and in areas of disturbance in the sheet-ground horizon.While high-grade ore was being mined, the operators sank seven churn-drill holes for the purpose of extending reserves. They then asked the Bureau of Mines to explore the deposit with the object of developing a reserve of lower-grade ore that could be mined by open-pit methods. Twenty-two holes were sunk. The methods of drilling and sampling and the logs of the holes, as of those drilled by the operators, are given later in this report.INTRODUCTION AND ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mined has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts development by each exploratory project as soon as practicable after its conclusion. Preliminary examination, conduct of exploratory work, and preparation of final reports are functions of the Mining Branch, Lowell B. Moon, chief, under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By P. G. Guest

Many of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed, in operating and anesthetizing areas. When ether was first introduced, candles and gas-lights and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions -many of them fatal to patients -have been attributed, with good reason, to sparks from static electricity. In this paper the authors present facts to show the prevalence of static electricity in the average hospital anesthetizing area, and the degree to which this easily developed electrical form of energy constitutes an explosion hazard. An effort is made throughout to explain how static electricity behaves, why it is a hazard, and why certain safety measures are needed and recommended. Following the introduction and a short general discussion of static electricity, which incorporates a glossary of pertinent electrical terms, an account is given of inspections and tests made in a number of hospitals. This account includes many suggestions that should be useful to any person who plans to make similar inspections and tests. However, a comparison of materials and equipment used with those described in the report will reveal, in many cases, the potential dangers and obviate the necessity for tests. The hospital work was supplemented by considerable laboratory research designed to determine the spark energies required to ignite anesthetic-gas mixtures and the exact amount of time involved in developing the usual static charges. The results of this research are reported and the implications examined. The paper concludes with a general discussion of static and related hazards in anesthetizing areas and of the most urgent preventative measures.

Jan 1, 1952

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By W. E. Robinson

A laboratory study wan made to determine whether drying and preheating Colorado oil shale with waste retort gases has any appreciable effect on its oil yield. Samples of crushed oil shale were heated at subretorting temperatures in a specially constructed electric furnace by gases similar in composition to waste gases from oil-shale retorts. The results of this study showed that preheating oil shale with nitrogen or a reducing mixture had no effect upon the oil or water yield. However, oxygen in the preheating gas caused a decrease of oil and an increase of water. In general, the oil yield decreased with (1) increase in oxygen content of the heating gases, (2) increase in temperature of the heating gas, (3) increase in heating time, and (4) decrease in the particle size of tho shale. The decrease in oil and the increase in water resulting from preheating were due to oxidation of the benzene-insoluble organic material (kerogen) rather than to oxidation of the benzene-soluble organic material (natural bitumen) in the shale, A small amount of oil was volatilized during preheating, which would constitute an additional loss if prober precautions were not taken to recover it. The results obtained in this laboratory study indicate that oil shale can be preheated without appreciable decrease in oil yield by proper selection of preheating conditions.

Jan 1, 1951

By W. W. Adams

"The ninth yearly National Safety Competition covering the calendar year 1933, conducted by the United States Bureau of Mines, w participated in by 332 mines and quarries situated in 35 States. Enrollment represented as increase of 10 plants over 1932, and one addition was made to the number of States represented.The primary purpose of the United. States Bureau of Mines in conducting the contest is to promote safety in United States mineral industries. This purpose is accomplished directly through the efforts of the competing companies and their employees to win first place in the competition and thereupon receive recognition on a national scale for their achievement the purpose is accomplished indirectly through studies by the United States Bureau of Mines of the facts contained in the accident reports the competing companies furnish to enable the Bureau to compute the accident rates that are the basis for determining the winners of the contest.The statistics which constitute the basis for determining the winning companies and the relative standing of all companies are prepared uniformly without regard to the States in which the companies operate, or to differences in classes of accidents covered by State laws relating to compensation for injuries resulting, from industrial accidents.Bronze trophies, known as 'Sentinels of Safety', which were provided by The Explosives Engineer magazine to be awarded annually by the Bureau of Mines, were presented to five companies in the contest of 1933, each company having established the best accident-prevention record within one of the five classes into which all companies were divided, namely, anthracite-mining companies, bituminous-coal-mining companies, metal-mining companies, operators of nonmetallic-mineral mines other than coal mines, and quarries or opencut mines. The trophies are awarded for 1 year and are then transferred to the winners of the succeeding year's contest.The trophy for bituincus-coal mines was won by a company in Wyoming. A company in Tennessee won the trophy for metal mining. In the nonmetal-mine group the trophy was again won by a company in New York. A quarry in Michigan won the trophy for the quarry-and-opencut-mine group. The trophy for anthracite mines remains in Pennsylvania, as all anthracite mines in the contest are in that State."

Jul 1, 1934

By H. P. Holmes

Tonnage quantities of hafnium metal have been prepared in Kroll-process equipment designed for producing zirconium. Some slight process modifications have been necessary, but overall operation is the same as for zirconium. Hafnium oxide is chlorinated in the presence of carbon and the resultant hafnium tetrachloride reduced by magnesium metal. Byproduct magnesium chloride is removed in a high-vacuum distillation step and the hafnium sponge metal crushed for further use. Arc-melted metal can be forged and rolled to sheet, but the best material produced to date would not be considered cold ductile. INTRODUCTION This investigation is part of the program for the production of pure metals from domestic and foreign ores that has been underway at the Bureau of Mines for several years. It was done in cooperation with the Atomic Energy Commission and the Bureau of Ships.

Jan 1, 1955

By D. R. Dolinar, A. T. Iannacchione

Limestone formations in the United States can be subject to relatively high horizontal stresses owing to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rock fall hazard. Rock falls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings has an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orienting the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and off-setting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

By M. E. Tyrrell, C. W. Houck

Mixtures of zirconium diboride and refractory metals of group VI were resistance sintered to high - density compacts using modified electric welding equipment . To evaluate the use of chromium , molybdenum , or tungsten as binders for zirconium diboride the sintered compacts were examined in polished sections and tested for crushing strength , hardness , microhardness , oxidation rate , and resistance to mechanical shock . Chromium yielded the highest compressive strength , the greatest resistance to mechanical shock and oxidation , and a satisfactory Rockwell hardness . Molybdenum did not yield a satisfactory cermet . Tungsten yielded compacts having high microhardness but very low mechanical strength .

Jan 1, 1964