Search Documents

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026

By Richard H. Granhom

Detonation pressure, or Chapman-Jouguet pressure, is an intrinsic property of an explosive, and like detonation velocity, is an indicator of explosive performance. Pressure and velocity are also important for calibrating computer codes and for other calculations such as the stress imparted to rock or metal by an explosive. The detonation pressures, P~cj, of many "ideal" explosives have been measured indirectly by recording some hydrodynamic flow variable other than pressure, with P~cj being inferred from hydrodynamics and the assumed Chapman-Jouguet equations. One such method is the difficult and expensive "aquarium technique''.] Commercial explosive manufacturers generally rely on estimates of P~cj generated by computer codes not explicitly designed for non-ideal explosives typically used in commercial applications. Over the last decade, U.S. national and government laboratories have developed in-situ gauge techniques such as the manganin gauge, for direct measurement of detonation pressure. Manganin is an alloy of copper, manganese and nickel, and is ideally suited for use as a pressure transducer because its electrical resistance changes with pressure, but is nearly constant with changes in temperature. A simplified manganin gauge technique adapted for use at a commercial test site is described and some initial results from measurements on commercial emulsion explosives are presented.

Jan 1, 1991

By Z X. Zhang

In sublevel caving mines, eyebrow break usually gives rise to lower ore recovery and worse safety in the field. Eyebrow break is caused mainly by two tensile stress waves: one from the front surface of a blasting ring, and the other from the roof of the drift. In order to reduce the two waves and finally to reduce eyebrow break at Malmberget mine, we employed two methods: (1) cartridge charge, and (2) double-primers in each blasthole. The two methods were tested in one ore body called ViRi. A total of 10 rings with the cartridge charge and 25 rings with the double-primers were blasted. At the same time a total of 34 ordinary rings were blasted in the same ore body. The result shows that the eyebrow break is 3.0 m for the ordinary rings, 2.3 m for the cartridge charge rings, and 2.1 m for the double-primer rings, respectively. In addition, the ore recovery for the double-primer rings is increased by 3% on the level of ViRi930, compared with that for the ordinary rings.

Jan 1, 2011

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980

By W. Jiao, Y. Yongqi, R. Shan

Soft rock mines are distributed through out P.R.C. And drilling and blasting is still the main method of driving a tunnel in these mines. Traditional smooth blasting has been widely and deeply studied and put into practice in P.C.R since 1970s. But the cartridge and blast hole are both columns, the stress field in the rock around blast hole at the beginning is symmetry around hole axis, and the original cracks in the rock can be activated randomly. So serious overbreak and underbreak at the boundary of an excavation occur often, especially when the excavation is in soft rockmass, and the rates of half-hole marks are generally about 50% in medium rock, and 20-30% in soft rock in Chinese coal mines. For the sake of overcoming the situation, we have been studying directed crack blasting since ten years, and have got some obvious achievements in this respect. Slotted cartridge control blasting in soft rock is studied in this paper. Through model experiments, reasonable decouple coefficient range and slot width are gotten, and unsymmetrical dynamic strain field is analyzed. Through underground test in soft rock with a strength lower than 1OMpa in Dayan Mining Bureau, The results of which the rates of half-hole marks and the nonsmooth grades of the cut contours are 83.3% and 1OOmm respectively have been achieved.

Jan 1, 2000

By Michael F. Barber

"Highway slopes are intended to remain stable over a long period of time. Unexpected slope failures can be costly in terms of human life and property damage or loss. Cleanup of failures can prove to beextremely expensive."

Jan 1, 1999

By Chanhwi Shin, Hyeongmin Kang

Mine optimization is a key strategy in the mining industry that focuses on improving the efficiency, productivity, and sustainability of mining operations. To achieve mine optimization, digitalization is essential for modernizing mining operations and attaining optimal performance. Due to the importance of mine digitalization, various software and platforms have been released to support this effort. Furthermore, by integrating these advanced technologies, mines can enhance processes, leading to significant economic and operational benefits. However, integrating data from various sources and collaborating across different platforms remains a significant challenge in the mining industry. Generally, data for mine optimization, such as mapping, smart drilling, FMS (Fleet Management Systems), fragmentation analysis, or vibration analysis, are collected and analyzed separately on different platforms. This separation makes it difficult to aggregate and utilize data comprehensively for overall mining process optimization. During the digitalization process, obstacles arise due to these complexity, variability, and sharing issues of data across different maker, sources, and methods. These challenges highlight the need for seamless integration to achieve optimal mining operations. Thus, this study applied a total solution that can cover the entire Drilling and Blasting (D&B) processes. The blast design was performed using actual terrain mapping data, and drilling and charging were conducted following a guide based on the blast design plan. After blasting, loading and hauling distances and fuel consumption were measured, and fragmentation for each blast was evaluated. All measurement tasks were automated to minimize human error. By collecting all data in one server, it became possible to perform an overall evaluation for each blast, allowing the identification of optimal values. In conclusion, to evaluate the optimization effects for each mining process, one month of integrated data collected on a single server was used. Compared to the period before the Total solution was implemented, there were notable improvements: a 25% enhancement in hole spacing, a 60% improvement in floor flatness, a 23% reduction in average fragment size, and a 19% improvement in fragment uniformity. Regarding cost savings per blasting volume, the improvements were 11.7% in drilling, 9.3% in explosives, 7.6% in loading, and 17.5% in hauling.

Jan 21, 2025

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Kirlk Yeager

"Ammonium nitrate (AN) is commonly mixed with a wide variety of additives to produce specialty formulations. Two additives commonly utilized are sodium nitrate (SN) and sodium nitrite (SNi). Application of the nitrite is primarily limited to gassing of emulsions. The nitrate, however, is incorporated in a wide variety of formulations. The effect of both these materials on the thermal stability of AN was examined. Experiments initially utilized lab-scale testing methods (sub-milligram sample size), such as differential scanning calorimetry (DSC), with scale-up to cook-off analyses (16 g) eventually applied. Labscale testing indicated that the presence of SN and SNi (both at 5 wt%) produced no harmful effects on the thermal stability of AN. The cook-off results did not agree with those from the lab-scale analyses, with both SN and SNi creating tremendous thermal destabilization of AN. These effects were seen at additive levels as low as 0.1 wt%. When SNi was employed as the additive, cook-offs became violent enough to create explosions in the testing apparatus. Although SN did not create as spectacular a destabilization, it did lower cook-off temperatures to approximately the same level as SNi. The dangerous situation created by SN andSNi seemed to be limited to cook-offs conducted in sealed vessels. If the SN/AN or SNi/AN formulations were allowed to cook-off in vented vessels, the thermal destabilization of AN did not occur. These results seemed to indicate that even “trace” amounts of what might ordinarily be viewed as benign additives could create significant destabilization of AN-based explosives under proper circumstances. Conditions created by blocked pumps, or deep boreholes could well overlap those produced in sealed cook-off vessels. In addition to showing the hazards potentially created by “benign” additives, the study also stressed that experiments designed to evaluate thermal hazards must include duplication of field variables to the fullest extent possible. "

Jan 1, 1999

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Robert L. Brooks

This paper is intended for companies at all levels of the Explosive Industry and in particular, those that do not have a risk manager. It is strictly informational in nature and no reference is made, or intended towards any existing insurance company or agency.

Jan 1, 1993

By Braden Lusk

Vibrations as a result of blasting practices in mining engineering are a complex phenomenon controlled by many variables. Mine blast vibration modeling and prediction is becoming more important as a consequence of interactions by mining activity with an ever closer public. Many communities (all over the world) close to mining activity often complain about airblast and vibrations produced from blasting activity. It is important for the mining industry to have tools and understandable methodologies to model and predict blast vibration. These tools can then be used to predict and control vibration at neighboring structures.

Jan 1, 2013

By William Reisz

In our line of work,like many other professions, there may be times when circumstances or a series of events may arise, contributing toward unacceptable risk. When multiple parties are involved, there will almost inevitably be differences on how best to deal with these situations. Unless approached in an intelligent and these differences may often have the potential for costly and unexpected results.

Jan 1, 2014

By Paul Downing

While safety and security have always been concerns of the U.S. explosives community, events throughout the world during the past few years have caused us to re-examine our industry’s potential vulnerability and change the way we do business on a day-to-day basis.

Jan 1, 2006

By Frederick R. Cosgrave

Blasting near buried Natural Gas pipelines has always been an area of great concern. Given the many variables that the blaster must contend with in determining how to break the rock while trying to keep the vibration low and doing so while not compromising the pipeline.

Jan 1, 1995

By Finn Ouchterlony, José A. Sanchidrián

"A model for fragmentation in bench blasting that originates from dimensional analysis of fragmentation in asteroid collisions is presented. Percentiles of the size distribution are obtained in the basic model as the product of a rock strength-to-explosive energy ratio, a bench shape factor, a scale factor or characteristic size and a percentage passing-related factor. The parameters of the model are fitted to 169 bench blasts in different sites and rock types, bench geometries and delay times, for which thefragmentation of the muckpile was obtained by sieving. The basic model is found to significantlyimprove with an additional factor describing the rock mass structure in terms of the spacing and orientation of discontinuities, and another one describing the delay between successive contiguous shots; the latter is conveniently formulated as a function of the P-wave velocity and the holes spacing. The rock strength property chosen is the strain energy at rupture that, together with the explosive energy density in the rock (or energy powder factor), forms a combined rock strength/explosive energy nondimensionalfactor. The model, called xP-frag, is applicable from 5 to 100 percentile fragment sizes, with all parameters determined from the fits significant to a 0.05 level. The expected error of the prediction is below 25 % at any percentile. These errors are half to one third of the errors expected with the best prediction models available to date."

Jan 1, 2017

By Rob Lederer, Chris Batten

Traditionally coal model digital terrain models (DTM) are created from lithological information obtained from broad scale exploration holes. The grid layout and distance between holes means that models do not commonly display local variations of seam dip, faulting and shearing. Due to this, issues can often arise when designing the loading of blast patterns based on potential variances between model and actual coal seam locations. Many sites will often attempt to create more accurate models through the collection of data from coal edge pickups on highwalls and in blast faces, along with information recorded by drillers (touch coal holes) from both production and presplit holes for both the current and previous blasts.

Jan 1, 2012

By Dirk Voogt, Quentin Steyl, D. Scott Scovira

A South Africa iron ore mine reported a decline in blast performance and ore and waste fragmentation. Preliminary investigation by the explosives services company found that the straight gassed bulk emulsion was breaking down and collapsing inside of some loaded slept blastholes. The bulk emulsion loaded at the subject site was manufactured in country and shipped to various clients throughout the region, with normal function in blasts at other sites. Historically, the bulk formulation emulsion being used at the subject mine site also performed well and without issue. This raised the question, “why is this bulk emulsion now breaking down and not firing in blastholes?”. Iron ore mines are not typically associated with reactive or acidic ground, and ground sample reactivity testing against the emulsion confirmed this. So, if not reactive ground or acidic water, then what is causing the emulsion to breakdown?

Feb 6, 2023