Search Documents

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By R. K. Rath

Adsorption, electrokinetic and flotation studies were carried out. The maximum density of adsorption of guar gum was obtained at pH 7.5 on sphalerite and at pH 11.5 on galena. Flotation recovery of sphalerite was reduced only marginally by the presence of guar gum in the pH range investigated, whereas recovery of galena was reduced to about 20% at pH 12. Differential flotation tests on binary mixtures indicated that 10 ppm of guar gum can depress galena and separate it from sphalerite at around pH 12.1. Co-precipitation tests confirmed the formation of a metal ion-guar gum complex in the bulk solution, suggesting that this is the precursor to adsorption. The adsorption isotherms for both minerals followed Langmuirian behaviour, but adsorption of guar gum on galena was significantly higher than on sphalerite and dissolution tests indicated that the concentration of Pb ions released from galena was an order of magnitude greater than that of Zn ions dissolved from sphalerite

Jun 21, 1905

By E Oktay, I Yusufoglu, C Kahruman

Powder and spherical pellets of MoO2 were oxidised under controlled conditions in the temperature range 674-791 K at oxygen partial pressures of 8.1-30.4 kPa. Weight increase during the reaction was determined by thermogravimetric analysis. It was concluded that the reaction is 0.6th order with respect to oxygen concentation and that the activation energy is 148 kJ/mole. In experiments conducted with powder, fast transfer of reaction heat to the gas phase created isothermal conditions, but the temperature of pellets rose by a maximum of 54 K at 674 K and 105 K at 791 K. The rise in temperature caused structural changes such as sintering and crack formation, which had a considerable effect on the reaction rate. The findings should be taken into account in the design of equipment and choice of operating conditions for roasting MoS2

Jun 21, 1905

By S. Kelebek

DETA exhibits a highly selective depressant action on pyrrhotite without adversely affecting the collectorless flotability of pentlandite and chalcopyrite in nickel-copper ores of the Sudbury region. A simplified Eh-pH diagram has been constructed to illustrate the extended stability of elemental sulphur and to explain the collectorless flotation of pentlandite and chalcopyrite. Cu and Ni ions, which are known to exist on the surface of pyrrhotite, promote the flotation of this mineral whether a collector is present or not. Thermodynamic calculations indicate that the action of DETA involves the sequestration of Cu and Ni ions from surfaces under a wide range of redox conditions; analysis of flotation test filtrate indicates as much as a 20-fold increase in the concentration of Ni and Cu ions. It appears that DETA may enhance the self-hydrophobicity of chalcopyrite and pentlandite by exposing more of the sulphur-rich surface sites for bubble contact in flotation. There are various possible explanations for its depression of pyrrhotite

Jun 18, 1905

By R. O. Suominen, P. A. Taskinen, K. R. Lilius, A. T. Jokilaakso

Chalcopyrite concentrate was flash-oxidised in a laminar-flow furnace in oxygen-nitrogen atmospheres that ranged in composition from N2 to N2 + 50 vol% O2. Gas pre-heating temperatures were 500-1100 degrees C and four particle-size fractions were studied: 28-38, 38-44, 44-62 and 62-74 micrometres. The effect of the residence time of the particles on sulphur removal was studied in the range 0.1-0.35 s. Scanning-electron microscopy combined with energy-dispersive analysis and back-scattered electron analysis was used to determine the morphology and mineralogy of the reacted particles. Total desulphurisation was achieved under the most oxidising conditions. Particles were observed to undergo fragmentation during oxidation, the violence of this depending on the iron and sulphur contents and the original particle-size fraction. The melting and/or reaction stages of the particles under different conditions were studied in powder samples. Polished sections were examined to follow the development of porosity and the mineralogy of the particles. A model for the fragmentation process is described

Jul 1, 1991

By G. M. Steed, A. O. Oyinloye

The deposit lies in amphibolite-facies biotite granite-gneisses of Proterozoic age, 4 km east of a major crustal break known as the Ifewara-Zungeru fault. Gold mineralisation is contained in a zone of quartz-carbonate (mainly calcite) veins and hydrothermally altered gneisses with associated small-scale intrusions along a steeply dipping second-order fault zone that roughly parallels the main fault. Gold is present mainly at grain boundaries between quartz and carbonate as discrete particles up to 100 micrometres in size, in general association with sparse, scattered pyrite, pyrrhotite and some base metal sulphides. Adjacent to the gold-bearing zone the granite-gneisses have been hydrothermally altered with minor volume increase, most notable enrichment being in K2O, S, Pb and Cu (and Au). High concentrations of Th, Y, Ce and Zr in the granite-gneisses imply derivation from S-type granites. It is likely that their high heat production capacity maintained the high temperatures needed to transport gold in the hydrothermal systems. It is most probable that the mineralisation dates from the Pan-African orogeny (650-450 Ma)

Apr 1, 1996

By H. L. Willett

Wrapping up the symposium, covers incidence of spontaneous combustion in British mines, assessment of liability to spontaneous combustion, precautions, rate of advance, starting a line of a coalface, local heatings at roadsides, burying packs, coal headings, retreating longwall, detection and sealant coatings.

May 23, 1905

By M. M. Cole

An assessment of the combined application of remotely sensed satellite imagery, geobotany and biogeochemistry reveals the complementary value of these techniques in the Thalanga area. The SPOT imagery yields useful information on features of the terrain and discriminates the gossan over the ore zone. Geobotany differentiates geological units and the anomalous vegetation provides visual expression of the surface presence of the ore zone, while biogeochemistry effectively locates its concealed extension below Tertiary sediments and ferricrete

Jan 1, 1991

By Q. H. Liao, B. G. Monaghan

The options for designing slopes in complex geological conditions are reviewed. It is shown that modelling, especially numerical modelling, allows a degree of analysis that cannot otherwise be achieved. Examples are presented of how numerical modelling can be used to investigate fundamental aspects of rock mass behaviour. It is demonstrated that an important consequence of change in scale is that the mechanisms of failure also change. The complex failure of the footwall slope at Aznalcollar, a large open-pit mine in southern Spain, is discussed. Numerical modelling with UDEC (universal distinct-element code) has allowed the realistic simulation of displacements measured in the field

Jun 18, 1905

By H. K. Taylor, B. Denby, L. D. Smith

Contributions by H.K. Taylor and G.A. Davis discuss the three papers published in Transactions IMM A, vols. 103 and 104, with responses by Smith and Dowd

Dec 1, 1995

By P. H. Morris

The profile of a delta formed by fine-grained mineral processing wastes, disposed of as aqueous slurries by subaerial deposition from a pipeline, has a significant bearing on the volume that is available for waste and water storage in a given containment structure. Earlier field data and laboratory experiments suggested that mine waste delta profiles could be predicted with high levels of accuracy using data from small-scale laboratory deposition tests. The relationships between the profiles of full-size and laboratory-model deltas were analysed using the principles of kinematic similarity and a recent theory of delta formation based on engineering hydraulics. Measured profiles of full-size and model coal-mine tailings deltas are compared and the prediction of full-size profiles discussed. It is shown that the data-derived laboratory-model deltas are insufficient to allow accurate prediction of full-size delta profiles. Initial slope data or other, equivalent data for the full-size delta are also required

Apr 1, 1996

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By T. Yalcin

In the Box-Wilson method, the correlation between dependent and independent variables is represented by a polynomial response function, whose constant and coefficients are determined by applying regression analysis to the experimental data collected. The five levels used for each variable consist of a minimum, a maximum and three intermediate values. A study was carried out using Ni-Cu ore from Sudbury, Ontario, in which 15 experiments designed according to the Box-Wilson method were carried out in random order and in duplicate. The two sets of replicate data showed close similarity, with an overall variance of 0.311 for the five parameters studied. The response functions were used to optimise frother dosage, collector concentration and air flow rate and an experiment was then carried out under the optimised conditions; the results agreed closely with those predicted by the response functions

Jun 21, 1905

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By E. H. W. Hornbrook, P. W. B. Friske

Paper presented at the 28th International Geological Congress, Washington DC, July 1989 (International geochemical mapping sessions). The objective of the programme is to establish and maintain a nationally consistent geochemical drainage database. Towards this end systematic surveys have been conducted since 1973. To date more than 200 surveys have been completed to the required standards, representing 180 000 sites and covering about 2 100 000 km2 throughout Canada

Jun 13, 1905

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By C. A. Jeffrey

The Dirtlow Rake vein deposit, which is up to 12 m thick, contains a range of paragenetically linked replacement mineralisation styles typical of many Mississippi Valley-type deposit environments. The main ore zone lies within the solution collapse breccia domes, the more southerly of which has recently been well exposed, allowing its relationship to the associated mineral-hosting structures to be studied. The domes were largely formed during early silicification, propagated by dissolution collapse and infilled by subsequent fluorite-barite mineralisation. The location of pipes and pervasive replacement was also controlled by early silicification. Structurally controlled bow tie shears were formed as a result of fluid access at fracture-bedding plane intersections. The nature and distribution of the mineralisation styles indicate that the degree of fluid access, residence time of solutions in contact with the wallrock and susceptibility of the limestone to silicification each played a major role in dictating mineralisation

Jun 19, 1905

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905