Search Documents

By Mohammad Mainul Hoque, Linhan Ge, Ai Wang, Geoffrey Evans, Subhasish Mitra

"Dispersed phase interactions involving bubbles and particles in the turbulent environment play a significant role in the flotation process. The conventional collision models only account for the deterministic rather than the stochastic behavior of turbulenct flow. What the bubble-particle collisions would be like remains an open problem due to the complex nature of turbulent flow. To address this research question, the present study aims to quantify the bubble-particle collision efficiency incorporating turbulence using the computational method. Multiple solid particles were released to interact with a single stationary rigid bubble (non-deformable interface). Effect of particles Stokes number, turbulent intensity (TI) and integral length scale on the bubble-particle collision efficiency (Pc) was examined. Large Eddy Simulation method (LES) was used to compute the continuous phase. Fluctuating velocity required at the inlet boundary condition was derived from Gaussian energy spectrum to generate the upstream turbulence. Discrete Phase Model (DPM) is used to simulate particle trajectory. The characteristics of turbulent flow were analyzed through Energy spectrum and energy dissipation rate. The critical initial releasing radius of the annulus, where Pc equals zero, reaches up to 1.5(Rb+Rp) under high turbulent intensity (TI) 20.48% compared to 0.23(Rb+Rp) calculated from the traditional Pc model. Pc decreases as the distance of initial releasing annulus between bubble centre increases. Pc increases as particle Stokes number increase up to 0.66. The collision efficiency for particles of St less than 0.38 is higher under TI 11.78% compared to TI 4%.INTRODUCTION To increase mineral recovery, interactions between bubbles and particles are essential. All flotation devices achieve it through introducing some level of turbulence into the system by increasing specific energy dissipation rate. Figure 1 shows three different flotation equipment, traditional floatation cell, Concorde cell and cyclonic-static micro-bubble flotation column (FCSMC), with different turbulence generation mechanisms – impeller, down-flow liquid jet and pump recirculation, respectively."

Jan 1, 2018

By Saeed Farrokhpay

It is known that the grinding condition has a major effect on the beneficiation characteristics of the minerals in subsequent processing, in particular, flotation. In the flotation process, particles surface and their condition can significantly influence collector adsorption and flotation performance. For example, particle shape and its surface roughness occurred during grinding may influence flotation characteristics of a specific ore. In fact, adsorption of different cationic and anionic species on mineral surfaces can be varied depending on the selected comminution procedure. The flotation performance of sulphide minerals can be detrimentally affected by the surface oxidation. The amount of surface oxidation may reduce the hydrophobicity of the mineral and makes adsorption of collectors less selective. Improved liberation may generally result in improved flotation recovery. However, this may result in finer grinding and slimes, and consequently, reduce the overall flotation recovery. This paper discusses the effect of wet and dry grinding on copper flotation of a complex Cu-Pb-Zn ore. Industrially, wet grinding is preferred due to its higher energy efficiency and owing to downstream processing requirements. In this study, series of flotation tests were conducted,and surface analysis (XPS and ToFSIMS) were performed after wet or dry grinding at two different P80 values. Mineralogical study was also conducted to investigate the liberation of valuable minerals after grinding. A higher copper flotation recovery was found for wet grinding. However, the copper recovery was increased by further grinding in both conditions (wet and dry). The results showed a higher collector adsorption on copper mineral surfaces after wet grinding. The surface analysis also revealed that the ore is slightly more oxidized after dry grinding probably due to higher temperature during dry grinding.

Sep 1, 2012

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By Bianca Foggiatto, Marcos Bueno, Rajiv Chandramohan, Eddie McLean, Greg Lane

"With the increasing depletion of high-grade ore deposits, smarter mineral processing solutions are required to achieve sustainable and economic methods for mining and processing low-grade deposits. In order to make the treatment of low-grade deposits economically viable, large quantities of rock need to be mined and processed. The associated infrastructure costs (power, water supply, accommodation and support services, waste storage) result in a substantial penalty on the project, from both capital and operating cost perspectives. As a consequence, the challenge for the mining industry is to overcome the associated rise in energy and water consumption as well as increased project complexity when processing large amounts of low grade ore. Ore sorting technologies have been used for many years, predominantly on small projects, enabling the upgrade of marginal ores. Several sorting methods based on characteristics including specific gravity, radiometry, colour, particle size, grade and other detectable physical characteristics have been employed. The challenge for large low-grade ore bodies is to crush and sort at coarser rock size in order to minimise specific energy consumption in comminution and to reduce waste disposal costs. For large projects, the understanding of the economic impact of ore sorting is limited. The economic drivers include plant head grade improvement; sorting infrastructure capital, operating and maintenance costs; waste material handling and other environmental costs related to waste disposal. This paper analyses the economic impact of ore sorting in a large mineral processing operation. The focus of the analysis is to compare NPVs for a circuit including screening and ore sorting stages. A project for processing an Australian copper sulphide ore is considered as an example for this study."

Jan 1, 2014

By N. N. Ngoepe

Positron Emission particle tracking (PEPT), which makes use of a radioactively labeled tracer particle, a positron camera and a tracking algorithm has been shown to be a viable method for studying flow properties in both the pulp and froth phases of flotation cells. Detailed velocity measurements of 300-400 µm glass beads were extracted to assess turbulence from velocity fluctuations in a micro flotation cell. The effects of particle speed and orientation at the instant of attachment events were studied. A minimum speed of 0.16 m/s was needed for a collision to lead to attachment. The most attachment events happen when the particle is directly in line with the inlet tube at 90o.

Sep 1, 2012

By Shobhana Dey

A low volatile medium coking coal from Jharia coal field, India was used for this investigation. The proximate analysis of the sample shows that it contains about 25% ash, 21.4% volatile matter and 52.4% fixed carbon. The sizewise ash analysis of -0.5 mm coal indicates that -0.5+0.15 mm fraction contains lower ash (21.9%) than -0.15 mm fraction (29.7%). The flotation characteristics of the -0.5 mm coal were determined by release analysis. The study reveals that recovery of combustible at 15% ash is about 27% and 43% at 17% ash level. The low recovery is due to the presence of high ash in finer fraction. In order to improve the recovery, the -0.5 mm feed was classified into -0.5+0.15 mm and -0.15 mm fractions, and subjected to flotation separately. The recoverable combustible obtained from the release analysis of -0.5+0.15 mm at 15% ash level is 46%. The effect of collector dosage, frother dosage and aeration rate on flotation was studied. The responses of these variables in collectorless flotation of the -0.5+0.15 mm fraction containing low ash were also studied. A lower aeration and frother dosage favored the generation of clean coal with low ash. The ash content in the tailing stream from -0.5+0.15 mm flotation circuit is close to that of the original -0.15 mm fraction. The former is ground to -0.15 mm and the two fractions are processed together. As -0.15 mm fraction contains relatively higher ash, collector aided flotation using sodium silicate was performed to recover the clean coal with 17% ash. The products of the overall flotation circuit having different ash levels were recommended for use in different applications. The reject from -0.15 mm flotation circuit contained 56.4% ash which can be used for fluidized bed combustion (FBC). This eventually leads to complete utilization of coal.

Sep 1, 2012

By A. Prokopiev

The biological stage of reclamation is the third final stage in remediation the damaged mining terrains, which is carried out following the completion of the mining technical stage. The biological stage of reclamation is carried out through restoration of the vegetation layer. The biological reclamation includes all activities related to the introduction into the terrain of vegetation, microorganisms, insects, and animals, with the acceleration of the succession and creating conditions for a sustainable ecosystem close to the natural one. It comprises of all anti erosion and other activities such as the preparation of the land for growing agricultural crops, sowing grass seeds, planting seedlings, amelioration of the soil and further care for the vegetation until its final place on the land. Mineral and organic-mineral ameliorants for biological reclamation were studied. The basic mineral ameliorant is Bulgarian natural zeolites. The zeolitic-rich tuff samples provided from Golobradovo deposit was characterized by their chemical and mineralogical composition and ion exchange properties and X ray analysis. The average content of clinoptilolite was found to be more than 80%. The materials had ion exchange capacity (NH4+) varying from 100 to 110 meq/100g. Chemical modifications of natural clinoptilolites were made in order to form active phases of nitrogen, phosphorus, potassium, and microelements. Slow-acting mineral ameliorant was developed. Organic-zeolite substrate for biological reclamation was developed. This new product is a mechanical mixture of organo-matter and modified zeolites. Agro-chemical parameters of new ameliorants were determined. The substrates including studied overburden dump soil and mineral or organo-mineral ameliorants are produced. The grass growth test was performed. Keywords: biological reclamation, ameliorants, damaged mining terrains

Sep 1, 2012

By T. Shumba

The solvent extraction section of an old Uranium Plant in the Vaal River region produced a sub-stance called Crud (Chalk River Unidentified Deposit) that formed within the aqueous/organic interface of the settler of the solvent extraction circuit. The crud was deposited together with gold tailings to the tailings dam many years ago. Previous research done on the crud confirmed that ex-posed crud leaches Mn and Ni at concentrations that are well above their acceptable risk limits as well as Zn that leaches at concentrations that are slightly lower than its acceptable risk limit. Soil washing and bioremediation technologies were employed to treat the contaminated soil. Various laboratory test work and the pilot scale studies were conducted in parallel with each other and the results of the laboratory studies were used to determine critical parameters. Four lixiviants, i.e. sulphuric acid, acetic acid, oxalic acid and ethylene diamine acetic acid were tested at three concentration levels i.e. 0.001M, 0.0001M and 0.00001M, respectively. Column tests showed that the leaching of the heavy metals increases as the soil porosity increases. Silica sand was added to increase porosity of the contaminated soil. Highest Mn removal was achieved mainly by sulphuric and oxalic acid at 0.001M at all soil levels. EDTA was significantly efficient in the removal of Ni and Zn. The recovery of heavy metals, particularly Mn, decreased as the depth of sampling in-creased. Heterogeneous bacteria and filamentous organism plate counts were conducted to evaluate the growth of the bacteria and filamentous organisms in the soil. Results showed that more organism growth took place in the bioremediated soil with a fertilizer added to it. The leaching of metals from the soil that was bioremediated in the pilot study was generally higher than the extraction of the metals from the soil that was leached with no bioremediation carried out. The results from this study suggest that the leaching of heavy metals from the contaminated soil is to a large extent dependant on the pH of the leaching solution. By increasing the soil?s porosity and bioremediating the soil, higher extractions of metals were achieved.

Jan 1, 2014

By Jerzy A. Mielczarski

The separation of albites from quartz by flotation applying the conventional HF-methods is no longer acceptable from an environmental and health point of view. Therefore, the search for a new reagent scheme without using HF depressor for separation of albite from quartz is under consideration. The flotation behaviour of ore mineral components depends on the produced hydrophobic or hydrophilic surface coverage (chemical functionalization). Currently we have excellent possibility of monitoring surface composition and structure at molecular and atomic levels at surfaces of natural minerals contacted with aqueous solutions of collectors, activators, depressants which is vitally important for the understanding of the surface chemistry that govern selective and efficient flotation. Detailed surface characterization of minerals before and after their exposition to different solution conditions was performed by the most modern spectroscopic techniques such as developed by us the infrared external reflection technique combined with spectral simulation and X-ray photoelectron spectroscopy (XPS). It is possible to monitor surface reactions which facilitate the separation process and those which bring disadvantage to selective flotation. At first we found that a small amount of ?mineral impurity? presented in natural ore could play important role in selective hydrophobization process. It was found that the pH of solution (parameter possible to control) and natural mineral impurities present in mineral samples (parameter related to ore origin) play a very important role in the separation process. Another important parameter is interaction between minerals, quartz and albite, present in aqueous solution. The limitation of flotation separation resulting from chemistry will be discussed. Moreover, the most promising scheme for separation of albites from quartz will be examined.

Jan 1, 2014

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

During incineration of municipal solid waste (MSW), some heavy metals and other environmentally harmful elements are liberated into bottom ash. The stricter environmental regulations require a higher immobilization efficiency of the ash before its safe disposal and application. Vitrification is one of the promising options, and has the advantages of high destruction efficiency of organics, high immobilization of heavy metals, and large volume reduction. The main components of the vitrified slag are SiO2, CaO, Al2O3, Fe2O3, Na2O and MgO, and the compositions have direct effect on the glass formation during vitrification, and further on the physical and mechanical properties of the slag. To provide essential data for the utilization of bottom ash as vitrified slag, the phase relations and thermodynamic properties of the oxide system need to be systematically investigated. In the present study, the liquidus temperature of the typical vitrified bottom ash slag was determined by using differential scanning calorimetry (DSC) measurement. High temperature equilibrium experiments were conducted to investigate the phase relations of the sub oxide system of CaO-SiO2-Na2O by means of Scanning Electron Microscopy (SEM), Electron Microprobe Analysis (EMPA) and X-ray Diffraction (XRD). The results show that the melting temperature of the vitrified bottom ash is around 930°C. In the CaO-SiO2-Na2O system with less than 50 mol% SiO2, the liquidus temperature de-creases with increasing amounts of Na2O along the tie-line of Na2O-Ca3Si2O7. Two compounds Na2Ca3Si2O8 and Na4Ca8Si5O20 are identified in the oxide system.

Jan 1, 2014

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By A. V. Neretin

This paper is a continuation and extention of the previous paper on energy-efficient placer mining methods which was presented in 2007 at the World Gold Conference in Cairns, Australia (Nere-tin, 2007a). The paper reports the results only on gravel processing as they were not fully discussed in the previous paper. It is common knowledge that placer gold mining requires processing of large tonnages of gold-bearing gravels by wash plants of different types. In Russia, gold-bearing gravels are mostly disintegrated and screened by the following types of wash plants: a water canon, a derocker or a scrubber trommel. Gold-bearing gravel processing is regarded as highly energy-intensive due to high energy consumption for transportation of large tonnage of material and high pressure water flow rate. The industries requiring a significant expenditure of energy normally estimate the process efficiency by energy consumption per product unit. In order to obtain quantitative data on energy consumption for gravel processing and to estimate placer mining costs, in 2003~2006 four placer gold mines located in the Irkutsk Region were thoroughly investigated through time and motion studies. At all these placer mines gravels were processed by a water canon, a derocker or a scrubber trommel. The objective of the study was to investigate the following parameters: ? wash plant throughput rate per hour; ? hourly diesel fuel and power consumption per cubic meter of gravel processed; ? volume per cent and shape of oversize material; ? different combinations of gravel processing methods. The results from this study were as follows: ? specific energy consumption per cubic metre of gravel processed for different combinations of gravel processing methods was estimated; ? a correlation between energy consumption and unit cost of gravel processing was determined; ? effect of yield and shape of oversize material on wash plant throughput rate per hour was de-fined; ? energy-efficient gravel processing methods were developed. Based on these results, an improved method of gold-bearing gravel processing was proposed. Implementation of this method at a placer mine saved US$ 123 000 in operating expenses only during a short-time Siberian placer mining season. At the same time, this method improved gravel disintegration, screening and processing operations used at the mine. Another advantage of the pro-posed method was higher gold recovery due to reduced yield of undersize material. In order to improve efficiency of gravel processing, a wash system including a derocker for primary gravel processing and a lightweight scrubber trommel was developed. There are two economic benefits of replacing water cannons with the proposed wash system. The first benefit includes lower operating costs for gravel processing due to lower specific energy consumption, while the second benefit is lower gold losses during slurrifying (disintegration and screening) and sluicing of the undersize material.

Jan 1, 2014

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

Calcium carbonate has three polymorphs: calcite, aragonite, and vaterite. Needlelike aragonite CaCO3 with a high ratio of length to diameter (aspect ratio) is widely used in plastics, rubber and ceramics as a filler and in pigments and paints as a carrier. This paper investigated the influence of H3PO4 dosage, reaction temperature, CO2 flow rate, and initial Ca(OH)2 concentration on formation of needlelike aragonite CaCO3. It was found that the presence of H3PO4 in Ca(OH)2 suspension resulted in rapid formation of (Ca5(PO4)3(OH)) crystal nuclei, which facilitated nucleation and growth of aragonite CaCO3 on the formed (Ca5(PO4)3(OH)) crystal surfaces. The results revealed that H3PO4 addition of P/Ca of 0. 2~0. 3, high temperature of 75~85 °C, low CO2 flow rate and initial Ca(OH)2 solid concentration of 1. 5 %~5. 6 % are beneficial to formation of aragonite. Well crystallized needlelike aragonite CaCO3 whiskers with length > 20 µm and aspect ratio > 15 were directly synthesized.

Jan 1, 2014

Mineral processing is an energy and water intensive activity. Mill comminution equipment usually has high energy requirements which necessitate extensive cooling to remove heat. Cooling requirements are typically 10% to 20% of the comminution energy. If there is an adequate supply of suitable water, open water-based cooling systems are the simplest, cheapest and most energy efficient cooling method available. This paper describes a method to determine the water demand for open water-based cooling systems at a plant and to determine whether the mine has sufficient water to meet that demand.

Jan 1, 2014

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered feed samples in a larger KC as op-posed to the commonly adopted GRG test has been discussed.

Jan 1, 2014

By Z. H. Xu

Flotation as a versatile multiphase separation technology has been practiced for more than 100 years in coal and mineral processing. Although effective over a wide particle size range, flotation for mineral separation has been largely understood as an art rather than a science, treating the flotation system as a black box. With rapid progresses in microscopic technologies coupled with high speed video recording and imaging analysis, ingénue design of visualization systems has made it possible to understand fundamentals of flotation by visualization. In this presentation, the state of the art where visualization plays a key role in advancing our fundamental knowledge of flotation will be reviewed. The areas to be covered include characterization of bubbles (shape, size, velocity and sol-ids loading) in a running flotation system, either column or mechanical cell, bubble-solid attachment, hydrodynamic cavitation in fine particle aggregation and flotation, froth imaging, particle-particle interactions by zeta potential distribution measurements, and heterogeneous gas nucleation by atomic force microscope imaging. With these capabilities, critical roles, good or bad, of ore proper-ties, solution chemistry, slurry hydrodynamics, and operation variables in flotation systems as applied to mineral, coal and oil sands processing were clearly elucidated.

Jan 1, 2014

By H. Breuer

Mineral processing is characterized by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customers´ requirements for product purity and consistent quality increase. Indian iron ores are characteristically friable in nature that results in generation of sizeable quantity of fines (0-10mm) every year during various stages of mining and processing in the country with grade varying from 50-60% Fe(T) and are high in silica/alumina (Al2O3 5-8%). The fines generated cannot be directly used for iron making (blast furnace/DRI units) in the country due its physical and chemical properties; therefore, large portion of it gets exported or dumped. Value addition to iron ore fines through various activities such as beneficiation & palletization is the need of the hour, which will not only be economically beneficial to the mining sector in the long run but also generate value addition & employment opportunities. Incentives may be given for adopting latest technologies for direct use of fines in iron making by agglomeration of fines in the form of Pellets and Sinters, as fines forms considerable part of iron ore resources. Due to selective mining, although the iron content of the ore is high but the alumina(Al2O3) content in iron ore is also significantly high which demands for beneficiation as high alumina will create problem during iron making like higher fuel consumption, poor quality of slag produced, reduced productivity of B.F. all mineral has been engaged in hematite iron ore beneficiation with its gravity and magnetic separators since the mid-nineties. The delivery of jigs started for the upgrading of iron ore for its utilization in a Direct Reduction Plant in Australia. Since then, various other installations with jigs for lumps and fines as well as upstream separators for fines are in operation in Brazil, Australia, India and South Africa. Low grade run of mine and/or dump ores are being processed with alljig®-, allflux®- and gaustec®-WHIMS as the core equipment. The article describes the technology in use, the characteristics of various iron ores and the product qualities achieved. The data presented shows the specific advantages of jig application on iron ore upgrading due to the possible high gravity cuts and the easy and low cost operation. The allflux®- technology provides the big advantage of high capacities and a two-step process, both in a single unit. The gaustec®-wet high intensity magnetic separators offer high capacity in combination with unsurpassed process flexibility. Keywords: iron ore, gravity separation, jig, upstream classifier, wet high intensity magnetic separation (whims), pelletization, sinteringMineral processing is characterized by a constant adaptation to changing raw materials and market conditions. It is the link between the mined raw material and a marketable product. As a lot of high grade reserves are exploited, a steady deterioration of raw material quality can be observed. At the same time, the customers´ requirements for product purity and consistent quality increase. Indian iron ores are characteristically friable in nature that results in generation of sizeable quantity of fines (0-10mm) every year during various stages of mining and processing in the country with grade varying from 50-60% Fe(T) and are high in silica/alumina (Al2O3 5-8%). The fines generated cannot be directly used for iron making (blast furnace/DRI units) in the country due its physical and chemical properties; therefore, large portion of it gets exported or dumped. Value addition to iron ore fines through various activities such as beneficiation & palletization is the need of the hour, which will not only be economically beneficial to the mining sector in the long run but also generate value addition & employment opportunities. Incentives may be given for adopting latest technologies for direct use of fines in iron making by agglomeration of fines in the form of Pellets and Sinters, as fines forms considerable part of iron ore resources. Due to selective mining, although the iron content of the ore is high but the alumina(Al2O3) content in iron ore is also significantly high which demands for beneficiation as high alumina will create problem during iron making like higher fuel consumption, poor quality of slag produced, reduced productivity of B.F. all mineral has been engaged in hematite iron ore beneficiation with its gravity and magnetic separators since the mid-nineties. The delivery of jigs started for the upgrading of iron ore for its utilization in a Direct Reduction Plant in Australia. Since then, various other installations with jigs for lumps and fines as well as upstream separators for fines are in operation in Brazil, Australia, India and South Africa. Low grade run of mine and/or dump ores are being processed with alljig®-, allflux®- and gaustec®-WHIMS as the core equipment. The article describes the technology in use, the characteristics of various iron ores and the product qualities achieved. The data presented shows the specific advantages of jig application on iron ore upgrading due to the possible high gravity cuts and the easy and low cost operation. The allflux®- technology provides the big advantage of high capacities and a two-step process, both in a single unit. The gaustec®-wet high intensity magnetic separators offer high capacity in combination with unsurpassed process flexibility. Keywords: iron ore, gravity separation, jig, upstream classifier, wet high intensity magnetic separation (whims), pelletization, sintering

Sep 1, 2012

By B. Vasanthakumar

In this study, the effect of adaptation of B.subtilis to sphalerite and galena with respect to the selective flotation of sphalerite from the sphalerite-galena synthetic mixture has been examined. The changes in the surface charge of the mineral and the bacterium, cell wall components and the profiles of secreted proteins are discussed. The flotation recovery of galena increases with the increase in the adaptation cycle of B.subtilis to sphalerite and galena, while the flotation recovery of sphalerite is independent of the adaptation cycle with either mineral. From the gel electrophoresis analysis, the protein profile for the unadapted and adapted cells is found to differ distinctly and this may be attributed to varying molecular weight fractions arising from different growth conditions. Electrokinetic measurements showed shifts in the iso-electric points of not only B.subtilis but also of the chosen minerals after adaptation. Additionally, the zeta potential of B.subtilis is found to become less negative after bacterial adaptation to the chosen sulfide minerals, while it showed an increase in the magnitude of surface negative charge after various enzymatic treatments. The change in the surface morphology and cell wall components such as phosphate, uronic acid and acetylated sugars of the bacterial species during adaptation to sphalerite and galena has been assessed. Selective flotation tests on a synthetic mixture of galena and sphalerite confirm that sphalerite can be preferentially floated from galena in the presence of the insoluble fraction of lysed B.subtilis cells initially adapted to sphalerite, with a high selectivity index. Keywords: bioflotation, b.subtilis, mineral adaptation, sphalerite, galena

Sep 1, 2012