Search Documents

By A. Rod Kern, Michael A. McNicholas, Yaser Taheri

Deep foundations were required for construction of an 18,000 ft2 (1,672 m2) 4-story office building and an adjacent 23,750 ft2 (2,206 m2) 5-story parking garage in Queens, New York due to an existing uncontrolled fill layer ranging from 15-20 ft (4.6 - 6.1 m) in thickness beneath the building footprint. The geotechnical engineers for the project initially selected auger cast-in-place (ACIP) piles over driven piles to limit the impact of noise and vibrations on the surrounding neighborhood. Ultimately, drilled displacement piles (DDP) were installed since this method offered a more economical solution that would generate the required pile capacity with shorter drill depths and would also mitigate spoils volume. During installation of test piles by the geotechnical contractor retained for the foundation work, multiple unanticipated soil conditions were encountered that would adversely affect the constructability of the piles. The existing fill contained significantly more natural and manmade obstructions than expected and the underlying glacial soil became too dense to penetrate at shallower depths than anticipated. This paper discusses how these issues were overcome through pre-drilling and the use of detailed instrumented test pile data coupled with in-house engineering capability to proactively re-evaluate minimum pile lengths at any given location and keep the project on track. INTRODUCTION Geotechnical work in the New York City market presents soil conditions that can be highly variable and challenging due to the presence of uncontrolled urban fill placed over the native soils. Construction in this area can therefore pose many unforeseen challenges, even with detailed geotechnical analysis being performed at project sites. A case in point is a construction site in Queens, New York. The proposed site development consisted of construction of a 4-story office building with a footprint of 18,000 ft2 (1672 m2) and a stand-alone 5-level parking garage with a footprint of 23,750 ft2 (2206 m2), together with associated new pavements and utilities. The site is bordered by a mix of commercial buildings and residential properties on all sides. Depth of the uncontrolled nature of the fill extended up to 20 ft (6.1 m) below street grade. Given the significant cost associated with removal and replacement, deep foundations were recommended to bypass the unsuitable soils and support the structures at depth where good bearing material existed.

Jan 1, 2019

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By Kamil Nuzha, Jianchao Li, Bashar S. Qubain

"The Philadelphia Water Department is rehabilitating Belmont Raw Water Basin. As part of this work, a 500-ft long, temporary cofferdam was designed to retain 35 ft of combined water and soil at the western half during the reconstruction of the eastern half. A cofferdam that comprises two integral rows of sheet piles was selected to take advantage of the soil’s weight between the sheet piles for increased stability. To fine tune the design, a geotechnical investigation was carried out to verify the subsurface conditions and, in particular, the top of rock variations along the centerline of the cofferdam. A detailed finite element analysis was performed based on the subsurface findings and incorporating the construction sequence to evaluate the behavior of the cofferdam at the following stages: installation of tie rods to connect to the two rows of sheet piles; partial excavation and installation of tiebacks; complete excavation of the east basin, and demolition of the cofferdam. Inclinometers and survey markers were installed every 100 ft along the cofferdam and were monitored throughout construction. The deformation measurements were in good agreement with the finite element results.INTRODUCTIONThe Philadelphia Water Department (PWD) Belmont Raw Water Basin is located at the intersection of City Line and Belmont Avenues in Philadelphia, PA. The facility actually contains two raw water basins, east and west, separated by an earthen dividing dike. Water leakage at the bottom of the basins and through the dividing dike together with increasing demand for a larger storage capacity dictated the replacement of the wide earthen dike with new narrower concrete structure. The temporary cofferdam was designed for a two-year period to facilitate excavation support, water cutoff, removal of the existing earthen dike and replacing it with a new concrete dike. During this construction sequence, the water level in the west basin had to be maintained at or near its full capacity.Various excavation support systems were considered for this project prior to the selection of a double wall sheet pile cofferdam. Fig. 1 shows a plan view of the cofferdam and the new dividing dike. A typical cross section of the two structures is shown in Fig. 2. Double row sheet pile walls are commonly used as both temporary and permanent retaining systems in open water applications such as construction works, quaywalls, breakwaters and revetments for storing industrial waste as indicated by Ohori, et al. (1984), Ohori et al. (1988), and Khan, et al. (2001). There are many advantages to double row sheet pile systems as recognized by Ohori, et al. (1984; 1988): (1) It can be installed and removed in the presence of water easily and quickly; (2) it provides stability with small width to height ratio, utilizing the existing soils between the installed sheet pile rows; and (3) it serves well as a means for water cutoff. These advantages meet the specific project requirements."

Jan 1, 2016

By George W. Little, John Councilman

"The selection, evaluation, and modification of contractor mix designs for self-hardening seepage barriers, completed by the slurry trench excavation method, can be one of the most critical and challenging tasks to ensure the cutoff wall meets the design performance criteria. Contractor mix designs should incorporate all available geotechnical data, including subsurface soil characteristics, groundwater information, and potential site contaminates. However, the pre-construction mix design can have limitations if subsurface data is limited or shows variability from initial investigations. Placement of the seepage barrier material needs to be evaluated during construction to identify in-situ performance. In one particular case study, the self-hardening cutoff wall mix design was evaluated over a one year period followed by a year and a half installation period, in which, a number of adjustments were made to the laboratory mix design during construction due to performance in the field. Installation for the selected mix was monitored on a real-time basis, using quality control data, as well as early strength and permeability results to determine if adjustments to the self-hardening mix were necessary. Evaluation of early results and relationships between strength and permeability were used to make adjustments prior to achieving the final test results for 28-day strength and permeability. Test results of the installed mix illustrated a direct correlation between strength and permeability. Achieving a minimum unconfined compressive strength was necessary to meet the minimum permeability of the seepage barrier. Other determinations conclude that the thorough development of a pre-construction mix design can have limitations even when all geotechnical data and site conditions are taken into account. Understanding early indicators and key strength and permeability relationships are necessary to determine seepage barrier performance and limitations.IntroductionThe evaluation of contractor mix designs for self-hardening seepage barriers was reviewed for one particular case study where a mix was developed using available geotechnical background information, including considerations for impacted groundwater. Following development of the laboratory mix design, the seepage barrier wall was installed over a one and a half year period, where the contractor mix design was evaluated and modified to accommodate field conditions affecting performance. The objective of the project was to cutoff and collect impacted groundwater and prevent the migration of contaminants to the creek running adjacent to the project. The self-hardening seepage barrier wall was installed using the slurry trench excavation method along 4700 ft of alignment and extended to depths ranging from 20 to 85 ft below ground surface, where it tied in with a low permeability stratum or competent bedrock."

Jan 1, 2016

By Prodyot Kumar Ray, Sudip Kumar Koley, Aminul Islam, Somnath Banerjee

One of the most important topics in the construction industry is the building of railway embankments. Being such a delicate and significant structure, it is crucial to properly design the embankment and build it while adhering to all statutory criteria and design guidelines. A railway embankment's subsoil condition and fill material, groundwater table, dynamic and static loads during operation, and embankment geometry are some of its most crucial design considerations. This paper discusses the likely causes of the collapse of a railway embankment in eastern India as well as the suggested rehabilitation scheme. It was observed that an embankment collapsed in the aforementioned area during a inccesent rain. Along with the side shifting of a cantilever retaining wall that was positioned at the bottom of the embankment, the embankment next to the railroad track settled vertically. According to the available geotechnical report, the sub soil strata in half of the area adjacent to the embankment profile, where the embankment height gradually decreases from maximum height, is stiff to hard clay with an undrained cohesion value of around 50 kpa followed by dense sand, and the sub soil strata in the other half is soft clay with an undrained strength of 15 kpa. As a result, in the rainy season due to the sudden increase in the water table, the self-weight of the embankment increased and further caused the under-laying soft clay to get squeezed away and settle. Due to this squeeze/settlement effect of the soft clay layer, the retaining wall got disturbed along with the generation of an undulated embankment top profile. As a remedial measure, it is proposed to construct a contiguous bored pile wall at the toe of the embankment to stabilize the slope, and additionally, compaction grouting is recommended beneath the embankment to improve the soft clay. In order to carry out the analysis, certain commercial geotechnical software like Slide, Wallap, and Plaxis 2D are used. The factor of safety of the embankment slope considering the above restoration scheme is adequate under static and seismic conditions.

Sep 1, 2022

By J. Racinais, P. Vincent

"In September 2011, Menard Oceania (MO) was engaged by Mac Mahon John Holland Joint Venture (MJHJV) to provide ground improvement solution for the $34bn Ichthys LNG development. With close to 400,000m2 of mangrove swampland set to be reclaimed and improved, this project was a great opportunity to showcase the technical, commercial and environmental benefits that Dynamic Replacement (DR) ground Improvement technique can provide. The ground improvement works involved complete design and construction for the Ichthys LNG site located at Blaydin Point on a low lying peninsula in Darwin Harbour. Dynamic replacement and stone columns technique were selected to treat intertidal mangrove mud to achieve required bearing strength, stability and limit settlement to an acceptable levels. The site is underlain by a 3m to 5m thick layer of highly organic mangrove muds with very soft shear strength ranging from 0kPa to 12kPa at depth. The site is exposed to daily sea water level tidal variations of up to 8m, which created significant constructability constraints and slope instability risks. This paper presents the design philosophy, the process involved in the selection of the construction methods, the site constraints encountered during the works and a review of the results achieved, quality control and post constructions performance.INTRODUCTIONInpex Browse, Ltd (Inpex) and its partner Total are developing the Ichthys gas field to pipe gas to onshore facilities at Blaydin Point on the south side of East Arm in Darwin Harbour. The proposed LNG plant consists of gas receiving facilities, 2 x 4.2Mtpa nominal capacity LNG trains, LPG and condensate production facilities, product storage and export facilities, a module offload facility (MOF), a flare pad (FP) and associated off plot facilities.The proposed on-shore facilities are located on extremely soft intertidal mangrove muds, therefore an appropriate ground improvement was required to achieve required strength and stability of site works and limit long term settlement to an acceptable level.Various ground improvement techniques were studied to select the most suitable for the ground conditions and site constraints encountered at the Blaydin point site. Dynamic replacement technique was selected for onshore section to improve soft mangrove mud to depths of 5.5m and Stone Columns (SC) technique was selected for MOF off-shore section to improve intertidal deposits to a depth of 2.5m.This paper presents DR design and construction works performed between December 2012 and August 2013 at Flare Pad Area."

Jan 1, 1900

By Kaustuv Bhattacharya, Manish Kumar, Nirbhay Singh, Prodyot Kr. Ray, Praveen Soin

This paper highlights salient features of an excavation 38 m (Length) by 10 m (Width) by 24 m (Depth) carried out in Central Kolkata. Secant pile wall (SPW) formed using a combination of alternating 1200 mm & 800 mm diameter piles was used. Six layers of struts and waler beams, including bottom slab were utilized as lateral restraints to piles. The geotechnical profile for excavation zone was predominantly silty sand to sandy silt. The profile is characteristic of river channel deposit usually encountered in Kolkata. Temporary stage analysis (including seepage analysis) and design were carried out in FEM softwares. Design checks for clay bursting, piping, bottom heave, etc. were also carried out. Extensive instrumentation and monitoring were carried out during the excavation period to check parameters such as ground movement, pile movement, piezometric heads, etc. as per review levels. During excavation, ground improvement using Tube-a-manchette grouting technique was also required to be carried out as per field observations. The paper discusses some of the major challenges faced as well as measures taken to counter them, during deep excavation carried out in silty soils in a very congested Urban setting in the heart of a Megacity.

Sep 1, 2022

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002

By Abid Adekunte

"In recent years, developers have had to deal with complexities associated with numerous cases of deep basement construction in built-up areas. Design and construction of deep excavation support systems in urbanised zones come with many technical challenges. Restricted working spaces often render the use of temporary struts as wall restraint systems unpopular, as working space needs to be maximised. Also, tie-back anchors are often inapplicable due to the existence of adjacent structures. Therefore, developing alternative restraint systems for deep basement structures in builtup areas is becoming increasingly important to the present day basement engineer.This paper is centred on the design, construction and monitoring of enabling works for deep basement structures on three sites in the United Kingdom and Republic of Ireland. Traditional tieback anchorage and propping systems were inapplicable on the sites. As alternatives, separate novel wall restraint systems were developed and adopted, to enable excavation on each of the three sites.Performances of the novel wall restraint systems, as well as the responses of adjacent structures were monitored. Numerical modelling and field monitoring results show the three alternative wall restraint systems to be safe and effective. The paper also highlights the advantages of the novel solutions over conventional methods.INTRODUCTIONRecently, deep basement structures have become popular components of urban building developments. As pointed out by Pearlman et al., 2004, this could be attributed to the inadequacy of surface parking spaces in urbanised zones, while underground parking facilities are also believed to improve both aesthetic and commercial qualities of urban structures.However, while the incorporation of basement structure into new urban development appeals to developers and architects, the engineering design and construction aspects of basement works typically come against a whole lot of complexities and challenges. As highlighted by Wong, 2002, engineering problems associated with basement construction in built-up areas are numerous, some of these include; complicated sub-soil conditions, dealing with excessive active pressures, complex temporary works, proximity of sensitive adjacent structures, high level hazards to construction workmen and surrounding community, inadequate working space, etc."

Jan 1, 2015

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

By Peter Cali, David Yang, Rakshya Shrestha, Ralph Griffin, Sushil Kafle, Motoji Watanabe

"As a part of the ‘US Army Corps of Engineers - New Orleans to Venice, Louisiana Hurricane Protection Project’, deep mixing ground improvement was designed to reinforce the soft ground for the emergency repair of a 7297-foot (2,224 m) long section of the Mississippi River West Bank levee in Buras Levee District under the contract ‘Emergency Levee Repairs – Contract P-17A, Plaquemines Parish, Louisiana’. The ground improvement utilizes a series of soil-cement panels oriented in the transverse direction of the levee. Each soil-cement panel consists of overlapped columns installed by the deep mixing method (DMM). DMM is performed from the existing top of levee and extended to competent stratum at depths varying from 26 feet (7.9 m) to 47 feet (14.3 m) below the working platform. The main purpose of the DMM panels is to provide shear resistance to the levee against lateral loads at high flood water condition. The DMM panels support the additional vertical load created by the increased height of the levee for hurricane protection and control the long-term settlement of the remediated levee, which might otherwise occur due to the compression of soft foundation soils. The total amount of DMM treatment is approximately 54,000 cubic yards (41,500 cubic meters). This paper reviews the project background, subsurface soil conditions and presents the design, construction and quality control of the deep mixing work for this levee repair project.INTRODUCTIONIn August 2005, Hurricane Katrina caused major damage to the federal and non-federal flood control projects in southeast Louisiana. In September 2005, Hurricane Rita caused further damage to this flood protection system. In an effort to minimize further damage and to enhance the protection level, certain non-federal levees located on the west bank of the Mississippi river in Plaquemines Parish, Louisiana were incorporated into the New Orleans to Venice Hurricane Protection project by the US Army Corps of Engineers (USACE). DMM techniques were then utilized by the USACE in several of these emergency projects and in many medium sized projects between 2006 and 2010 (Bruce et al. 2012). This project (called P-17A hereafter) which forms a part of this protection system is executed under the contract Emergency Levee Repairs, Contract P-17A. This is one of the largest projects of the USACE after LPV- 111. The huge LPV-111 project (5.5 miles (8.9 km) of levee) treated by DMM), the largest DMM project ever conducted outside Japan, began in 2010 and was completed in 2012 (Cali et al. 2012, Bruce et al. 2012).DMM is utilized at P-17A to construct a series of soil-cement panels oriented in the transverse direction of the existing levee to provide shear resistance to the levee against the lateral load during high flood water condition. The project extends 7297-foot (2,224 m) along the West Bank Levee of the Mississippi River in the Buras district of Louisiana, parallel to Louisiana Highway 23 (LA-23) as shown in Figure 1. It is located approximately 60 miles (96 km) south-east of downtown New Orleans."

Jan 1, 2015

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By Jeremy Butkovich

Dynamic soil-structure interaction (DSSI) analyses are becoming more common in bridge designs, especially in seismically active areas. Because of its proximity to two active fault zones, the Evergreen Point west approach bridge replacement will be base isolated, and will be designed using DSSI. The project team completed two independent bridge designs to satisfy peer review requirements. The designs required substantial characterization of the soil dynamic behavior using both laboratory and in-situ testing. The analyses made use of earthquake time histories spectrally matched to conditional mean spectra. This led to reduced, and more realistic seismic demands on the structure, compared to conventional uniform hazard spectrum matching. The bridge analyses suggest that the preliminary bridge design is relatively conservative. This will allow the design team to potentially reduce shaft/column diameters and reinforcement. The design team estimates that the dynamic analysis design could represent a net savings of around $60 to $90 million compared to a conventional design.

By Masaki Kitazume

"Many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction which occur in a loose and saturated sand layer, induces quite large damages of infrastructures, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Many kinds of ground improvement techniques based on various improvement principles have been developed for earthquake disaster mitigation. Among them, the grid type deep mixing method has been often applied to liquefaction mitigation. In the method, the stiff grid walls are constructed by mixing the soil and binder in-situ, which are expected to restrict the shear deformation of the soil within the grid walls so that the pore water pressure generation can be remained small. The high applicability of the method was confirmed in several earthquakes, including the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake. In this paper, the development of the method, some applications of the deep mixing method to earthquake disaster mitigation are briefly introduced. INTRODUCTION In Japan, many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction induces quite large damages, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Table 1 shows the amount of damage to port facilities (Noda, 1991). According to the table, the amount of damage when liquefaction takes place is about 20 to 50 times larger than that without liquefaction. This highlights the importance of liquefaction mitigation to minimize earthquake disasters. There are many kinds of soil stabilization techniques developed for liquefaction in Japan. Among them, the deep mixing method (DMM), an in-situ cement stabilization techniques, was developed in 1970s in Japan and has frequently been applied to improvements of clayey and sandy soils (Kitazume and Terashi, 2013). The grid type DMM has been often applied to prevent liquefaction, where the grid of stabilized column walls function to restrict generation of excess pore pressure in the soil within the walls by confining the soil particle movement. The improvement effect of the method was first evaluated in the Hyogoken-Nambu earthquake in 1995 and was also evaluated in the Tohoku earthquake in 2011. In this paper, some successful performance of the deep mixing method to earthquake disaster mitigation in the two earthquakes are briefly introduced."

Jan 1, 2015

By Raffaella Granata, Daniele Vanni

"This paper presents the drilling and grouting program performed at two abandoned landfills located into former calcarenite rock quarries in Manfredonia, Italy. Tests performed after the abandonment of the landfills detected leachate infiltration into the groundwater, which required the implementation of a remedial program. In order to seal the rock fissures and create an impervious basin at the base of the two landfills, sub-horizontal boreholes were drilled and grouted into the rock under the waste deposits. At the same time, sub-vertical boreholes were drilled and grouted along the perimeter, to laterally confine the landfills. Finally, the landfills were properly capped with an HDPE membrane, geogrid, geotextile and topsoil. The methodology implemented to create a watertight barrier under the two landfills was innovative and cost-effective. Moreover, the drilling and grouting minimized the environmental impact of the remedial work, since the waste remained in their original location and were not affected by the remedial process.IntroductionThe two landfills, “Pariti-1 RSU” and “Conte di Troia”, are located approximately 6 km (4 miles) southwest of Manfredonia, a small town close to Foggia, Italy (Fig. 1). These landfills are located into two rock quarries, formerly used for the extraction of calcarenite (i.e., a weak calcareous sandstone, in tuff facies), and were abandoned in the early 90s. The two landfills cover a total area of about 45,000 m2 (11.2 acres), and mainly include urban solid waste with a depth of up to 25 m (82 ft). The main characteristics of the two waste landfills are listed in Table 1."

Jan 1, 2016

By Carlandrea Albonico, Salvatore Miranda

The paper describes an innovative geotechnical engineering solution that has been provided within the scope of the Galataport Project, in Istanbul, Turkey. Among all interesting geotechnical works included in the Project, this paper presents the design principle, adopted technologies and performance controls related to the Multi- Purpose Bottom Plug (MPBP). This original geotechnical engineering solution has been employed for the deep basement excavation in Karaköy and consists of a combination of seepage control, ground improvement, and load bearing elements, which have been executed with double-fluid jet grouting, pseudo-elliptical jet grouting and permanent micropiles, respectively. The paper highlights the importance of employing cutting-edge technologies within the foundation engineering field and state-of-the-art electronic control devices, in parallel with the essential human expertise, in order to obtain the desired results in this high-profile Project.

Nov 1, 2022

By Gihan E. Abdelraham, Youssef G. Youssef, Mohamed M. Kamel

"Previous studies defined Narrow Mechanically Stabilized Earth, NMSE, walls as a retaining wall with aspect ratio (wall width to its height, L/H) less than 0.70 as in traditional walls. Some studies investigated its behavior and its failure planes compared to those of traditional walls. In this paper, parametric study using finite element analysis PLAXIS, 8.2 has been introduced to discuss global factor of safety, FS, maximum horizontal displacement, Ds, maximum tension force of reinforcement element, Tmax, and active earth pressure coefficient, ka, as a function of different aspect ratio of NMSE wall, L/H, reinforcing elements spacing, S, elastic axial stiffness of reinforcement element, EA, wall batter, 1/m, soil friction angle, f, and wall height, H. The results indicated that increasing aspect ratio increases the factor of safety, maximum horizontal displacement, maximum tensile force and active earth pressure. Increasing elastic axial stiffness increases factor of safety, maximum tension force of reinforcement element while decreasing the maximum horizontal displacement.IntroductionReinforced earth is a composite geoconstruction material, which embodies two basic components; namely engineering fill and reinforcing elements. The latter one is responsible for improving the tensile and shear resistance of the soil. The soil-reinforcement technique has been in use for many geotechnical applications especially MSE walls.A narrow wall system is referred to as a MSE wall with an aspect ratio, L/H, below 0.70 that is placed in front of a stabilized wall. An example of a narrow wall system with its dimensions is illustrated in Fig. 1."

Jan 1, 2017

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009