Search Documents

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By Vijaya R, Boominathan A

The design of a rubble mound breakwater resting on a problematic seabed is quite challenging and expensive. In the present study, stage-wise construction of a typical section of the breakwater for a proposed port on the eastern coast of India is carried out. The major challenge envisaged in the design of breakwater is the subsoil strata which consists of soft clayey soil. As it is difficult to improve the soft clayey soil in the marine condition, construction stages are meticulously planned in such a way that consolidation takes place due to the preloading of breakwater, which in turn leads to the strength improvement without any special ground treatment. Thus, the breakwater is designed to be constructed in 7 stages. An initial geostatic analysis is carried out, followed by a plastic stress-strain analysis, consolidation analysis, and safety analysis for each stage, using finite element (FE) code PLAXIS. It is found from the FE analysis that due to the presence of the soft clayey soil, the critical slip circle was formed in the base. It was observed that the staged construction over a period of 2 years provides a sufficient increase in the factor of safety of above 1.5 at the various stages of construction. Hence, it was recommended to construct the breakwater with 7 stages over a period of 2 years.

Sep 1, 2022

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By B. B. Broms

A method for calculating the bending moment induced in misaligned or bent piles is described, The maximum bending moment varies with the angular rotation between the pile segments, the coefficient of horizontal subgrade reaction of the soil and the flexural rigidity of the piles. A case history involving damages to misaligned 365 x 365 mm square precast concrete piles is described.

Jan 1, 2010

By John D. Nelson

Foundation underpinning is a common component of remediation schemes for distressed foundations on expansive soils. For many applications in expansive soil, micropiles have distinct advantages over other techniques. This paper will concentrate on the design and construction of micropiles in expansive soil. It discusses the nature of building distress and the relationship between foundation movement and soil heave. It presents methods for determining the factors that are required for the design of micropiles. Such factors include calculation of expected free-field heave, depth of soil wetting, and prediction of pier movement. A finite element program developed by the authors and others to determine pier heave and internal forces is presented. The input parameters that are required for pier analysis are discussed, and the nature of the output and the sensitivity of the results to the output are described. A case example illustrates the advantages of micropiles over other methods.

Aug 1, 2013

By Christian B. Woods, Joe C. Drumheller

"Kenneth A. Huber, P.E., Langan Engineering & Environmental Services, New York, New York, USAThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. The Prudential Center site encompasses an entire city block that had a varied history of uses ranging from a cemetery in the late 18th century, to a rail yard and train station for the now-defunct Central Jersey Rail Road in the 19th and early 20th centuries, to commercial development in the latter half of the 20th century. Each of these prior uses presented challenges to the design and construction of the Prudential Center that required innovative engineering solutions, including: archaeological investigation and exhumation of the former cemetery occupants, protection of historic buildings surrounding the site, and extensive demolition to remove old train bridge foundations.The design team was required to develop potential foundation systems for the arena. Several foundation concepts were evaluated for cost and constructability, including: driven piles, drilled shafts, and shallow foundations on improved subgrade. Following a detailed cost analysis and value engineering exercise, the decision was made to support the arena on spread footings following the completion of a multi-phased ground improvement program consisting of a combination of dynamic compaction and removal and replacement. To evaluate achievable allowable bearing pressure as part of the design, a dynamic compaction test section was performed within the building footprint prior to the start of production work; this resulted in an increase of the allowable design bearing pressure from 2 tons per square foot (tsf) to 3 tsf. This reduced the expected foundation costs by 30% and gained sufficient time in the schedule to allow for the completion of the arena in time for the New Jersey Devils 2007- 2008 hockey season.BACKGROUNDThe dream to bring New Jersey Devils hockey to the largest city in New Jersey became a reality in the summer of 2005, when construction began for the Prudential Center in downtown Newark. After several years of negotiating between the City of Newark, local landowners, area developers, and the Devils themselves, a deal was finally struck to erect Newark Arena, now known as the Prudential Center, right next to City Hall. This is not to say, however, that once the site location was finalized, that no further challenges were encountered in the construction of Newark’s new crown jewel."

Jan 1, 2015

By Rudolph P. Frizzi

This paper presents different deep foundation systems and associated settlement records for high-rise building projects in the coastal areas of southeastern Florida. An introduction to the sedimentary soil and soft rock geology in coastal areas of southeast Florida is presented, and the deep foundation systems utilized include: piles of varying length, pile supported mat, preload and short piles, and drilled shafts. The implementation and associated settlement monitoring data of the different deep foundation systems are described through case histories involving 20 to 66-story buildings. In addition, the deep foundation systems and settlement monitoring results for twenty-one additional high-rise building projects in the coastal areas of southeastern Florida are presented.

Jan 1, 2003

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By Leong, William. Chong, Kam Weng

Deep Vibro Techniques namely Vibro Compaction (VC) and Vibro Replacement (VR) are widely used in ground improvement to densify sands and strengthen cohesive soils. This paper describes the application of these techniques for the construction of 20 Ha Iron Ore Stockpile Yard with the maximum stockpile height of 14 m in Quang Ngai, Vietnam. The challenges of this project are to limit the stockpile allowable settlement and the surrounding pile’s lateral movement. The soil condition can be summarized as 12m – 18m thick of loose to medium dense SAND with qc around 5-18MPa and followed by 2.0 – 6.0 m thick soft clay with qc around 0.4 – 0.8MPa. Localized very dense sand layer was found. VR using stone columns were installed in soft clay layer while VC was adopted to densify sand layer. Additional shallow stone columns were built in sand strata to minimize pile top lateral movement. The post construction performance was verified by a large 6 m by 12 m plate load test (PLT). The predicted PLT deformation using Priebe’s improved properties for the VR will be presented and compared with the measured plate load test results.

Nov 1, 2022

By Ali Porbaha

In today's fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By Dennis J. Riley

A. This outline addresses what a sub-contractor, or a subsub-contractor should do to get paid in the event the general contractor or building owner files for bankruptcy. B. Negotiating payment terms. Progress payments vs. "pay when paid". How a sub or subsub can avoid financing the contract. C. Court interpretation of "pay when paid" clauses allow postponement not excusal of payment. See, e.g., Seal Tite Corporation v. Ehret. Inc., 589 F. Supp. 701 (D.N.J. 1984) (where the court held that the general contractor could not delay payment indefinitely to the subcontractor in the event of non-payment from the owner); United Plate Glass Co. v. Metal Industries. Inc., 525 A.2d 468 (Commw. Ct. Pa. 1987) (where the court held that payment from owner was not a condition precedent to paying subcontractor but instead a timing mechanism indicating when payment should be made); But see. Straham v. Landis Construction Co., 499 So. 2d 417 (La. App. 4 Cir. 1986) (where the court strictly interpreted the "pay when paid" clause).

Jan 1, 1991

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

By Ali Ebrahimi, Meena L. Viswanath, John F. Beech, Mustafa B. Erten, Ming Zhu

"Excessive deformation of a cantilever sheetpile wall can occur due to dredging, excavation, backfilling, or long-term creep behavior of soil. A buttressing berm constructed in front of the wall can be considered as a mitigation technique to prevent or decrease the deformation by increasing the passive earth pressure and thus improving the wall stability. The effect of the buttressing berm on the stability and deformation of a sheetpile depends on the berm geometry (i.e., the thickness/depth and the width) as well as the properties of the sheetpile and the adjacent soils. A parametric study was conducted using a conventional limit equilibrium method. Design charts were prepared to evaluate the effect of a buttressing berm and the soil friction angle on the wall stability and deformation. These charts can be used as a tool by geotechnical engineers to make a quick estimate of the required size of a buttressing berm in case of calculated or unexpected excessive deformation of a sheetpile. An analysis of the effect of a buttressing berm on the stresses and deformation of a sheetpile was also compared with the results from finite element analysis. The results of this comparison are discussed.INTRODUCTIONCantilever sheetpile walls are commonly used to support excavations. Sheetpiles are hot rolled or cold formed sections of steel made to interlock with adjacent sections to form a continuous structure providing lateral support. Sheetpile walls can be cantilever walls or anchored with tiebacks. To construct a cantilever sheetpile wall, sheetpiles are driven by pile drivers or vibrated in to a design depth sufficiently below the depth of excavation. Excavation can then proceed in front of the sheetpile wall, which resists the earth pressure loading from behind the wall. The design depth and geometry of the sheetpile wall depend on the soil conditions, the depth of excavation, and the tolerable deformation. In certain cases, when a small buttress of soil can be left immediately adjacent to the sheetpile wall, the required depth or geometry of the sheetpile wall can be reduced or adjusted, which can significantly decrease the cost of procuring and installing the wall. Such a buttress can also serve as a short-term or long-term remedy in case of observed excessive deformation in a constructed wall. Traditional methods of analyzing the stability of a sheetpile wall do not account for the passive pressure effects of this small buttress. In this paper, a parametric study was performed for a variety of soil types and wall and buttress geometries by implementing traditional limit equilibrium methods in commercial software and design charts were created illustrating the effect of a buttressing berm on sheetpile deflection. Selected cases were then modeled in a finite element software to compare the results with the traditional limit equilibrium method. The resulting design charts can be used as a tool by geotechnical engineers looking to reduce the design geometry of a sheetpile wall or address observed excessive deformation in a constructed sheetpile wall."

Jan 1, 2016

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018