Search Documents

By Alireza Ayoubian, Douglas S. Roy, Gianni O. Chieruzzi

"A 400 MW, gas-fed power plant on floating piles and piled raft foundations was constructed in the Province of Moskovskaya, Russia in 2008. The subsurface is characterized by fill underlain by loose to medium dense alluvial deposits, with peat and clay interbeds, a stiff to hard, highly plastic, silty clay stratum of glacial origin, and a stratum of very dense, varved interbeds of sand and silt.More than 800, drilled concrete piles were constructed at the site. The pile length ranged from 15 to 23 meters below existing surface grade, and the pile diameter ranged from 0.9 to 1 meter.Initial analyses by others predicted total power plant settlements of 3 to 4 cm when subjected to the permanent loading conditions. Under a peer review process for the equipment supplier, subsurface investigation and testing were performed to verify the consolidation parameters used for foundation design of the power plant foundation. The parameters obtained in this investigation were used in the 3-D finite-element model ELPLA as inputs for the settlement analysis of the turbine building and power island. The ELPA analyses predicted settlements on the order of 7 cm over a period of 30 years. The actual settlements after two years of monitoring were compared against the model predictions. The rate of settlement and the recompression index were both underestimated in our model. The measured settlements have enabled us to calibrate both of these model parameters so that the model better matches the data.IntroductionA 400 MW, gas-fed power plant was constructed near Moscow in the Province of Moskovskaya in Russia.Figure 1 shows the general arrangement of the main structures, and the geometry of the piles supporting those structures."

Jan 1, 2017

By Jochen Maurer, Dr. Christian Hoyme, Dr. Hans Regler

Currently, it is very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. As a rule, companies depend on reports from on-site experts. There is no end-to-end digitalization due to the mobility of equipment and ever-changing locations. Equipment from different manufacturers, especially in special foundation engineering, is highly specialized. Any data collected by this equipment is recorded in proprietary formats and made available on the manufacturers' platforms. This exacerbates the situation, making simple analysis of performance indicators impossible. Most functions such as construction diaries, equipment utilization analyses, etc. are implemented only as standalone solutions. This does not allow for prompt visualization and intervention in critical process sequences because the construction site process is usually managed using a cost-based method. Furthermore, special foundation engineering requires a high level of expertise in an extremely wide range of construction processes. In this article, the results from a set of non-proprietary performance analysis tools are presented using numerous practical examples. Once a construction element is completed, the equipment data is immediately transferred to the platform using the latest cloud technology. Because the data is normalized, construction progress can be documented immediately, even for mixed equipment fleets. Bottlenecks can be immediately detected by visualizing the current performance of the production process, which is broken down into individual steps. Modern analyses of this equipment data improve quality, thereby providing better information about current performance. These sets of tools are essential for changing from the current monetary or cost-based method of process management to time- and bottleneck-oriented management. This makes it much easier to identify the critical path during projects. The article shows that processes can be documented and managed.

By Dharmil Patel, Michael J. Chow

"Construction progress is nearing completion at a Brownfield Site for a 100,000sf mixed-use 10 story building plus cellar for Silver Star Motors including a two-floor pre-owned Mercedes Benz showroom; high-end residential rental studios, 1, 2, and 3 bedroom apartments; and penthouses on the upper two floors. Excavation through impacted soil extended to 15ft depth. Project is approximately 7 ft north of a NYCT subway station, portions of the SOE are within inches of a 6ft diameter NYCDEP Sewer, and cellar extends below the depth of adjacent structures, requiring over 200 lf of underpinning.A complex series of earth retention systems was utilized consisting of underpinning, drilled-in soldier piles (micro-piles), timber/concrete lagging, soil anchors and inclined rakers supported by a partially constructed foundation mat. Foundation mat subgrade was approximately 4 ft below the groundwater level creating more challenges during underpinning and achieving suitable foundation subgrades. All construction was undertaken on a non-union basis.This paper describes the design, construction, and lessons learned for the multiple earth retention systems, Brownfield Remediation requirements, instrumentation, and monitoring used to manage complications of building adjacent to an active subway station, in close proximity to existing utilities, with underpinning and mat foundation installation below the water table.Results of the instrumentation program are summarized which utilized an AMTS, monitoring prisms on adjacent structures, automated seismographs, and manual NYCT surveys."

Jan 1, 2016

By John R. Grillo, Gordian Ulrich, Franz-Werner Gerressen

Most geotechnical construction professionals are aware of piling using hydraulic drill rigs and the so-called Kelly drill mode. Kelly drilling has many advantages as it can work with a wide range of tools facing almost all types of soil and rock conditions. Kelly drilling can also deal with diameters up to 10 ft (3.00 m) and bigger or depths of more than 330 ft (100 m). Nonetheless, there is a concern about Kelly drilling as it is a relatively slow installation process. Therefore, an alternative piling method like Cased CFA (CCFA) Piles (Cased Auger Cast Piles) provides a significant advantage in terms of installation performance, schedule and cost saving potentials. Major application for the Cased CFA system is the secant pile wall construction. Against the traditional secant pile wall systems like fully cased bored piles or CFA secant piling the Cased CFA secant pile wall system has the advantage in cost and time against the fully cased system and in quality against the standard CFA system. This paper will describe the methodology and installation process in general as well as first reference projects carried out in the United States. This paper will present the results in cost and schedule saving using this method. In addition, we will also describe the limitations of this method. INTRODUCTION In the changing construction environment, companies are searching for new technologies or improvement of existing technologies to complete their projects in shorter time frames to provide a good economic solution. Especially with the focus of increasing urbanization, the aim of fast construction becomes more and more important. When thinking of piling, most people will have the same picture in mind: that of a hydraulic drill rig working in Kelly drilling mode; however, the perpetual drill rig development provides a number of options for the execution of specialist foundation projects, either for foundations or for pile walls when using single pass applications like CFA, Cased CFA and Full Displacement Piling (FDP). Single pass means, in general, that the tool is pushed and rotated into the ground to the final depth in one stroke. After reaching the final depth, concreting is started and concrete is pumped continuously while the tool is withdrawn.

Jan 1, 2019

By Carl-Oscar Nilsson, Åke B. Nilsson

"The embankment dam at Storfinnforsen is 23 m high and was completed in 1954. The dam has an impervious zone with timber sheet piles and a support fill of glacial till. The pore water pressure in the downstream shoulder has during recent years increased due to deterioration in the sealing function of the timber sheet piling. There is a concern that the high pore water pressure in the glacial till will cause internal erosion initiating at a thin coarse transition layer between the glacial till and the rock fill along the downstream toe. As a remedial action in order to improvement of the leakage resistance a supporting berm of coarse rockfill against the downstream slope of the dam was constructed in year 2013. In addition a new impervious seal in the centre of the dam e.g. a diaphragm wall was considered. However, after further studies and a trial stretch of 40 drains each 20 m long and diameter 0.3 m an alternative with vertical drilled drains in the downstream support was selected. A contract has now started up to drill in a similar way to treat the full length of the dam with drains. The work is in the planning to be completed in 2016.Dam ConstructionStorfinnforsen Embankment Dam was put into operation in 1954. The dam is 330 m long and maximum height is approximately 23 m. The dam is constructed with a central core zone and supporting zones of earth and rockfill on the upstream and downstream sides giving an almost symmetrical cross-section about the dam axis, see Fig. 1. The upstream slope is 2H:1V down to el. 270 and 2.5H:1V below. On the downstream side the slope is 1.75H:1V down to +269 and 2H:1V below. The core zone consists of a timber sheet pile wall with a Zone 5 of glacial till, approximately 2 m wide, adjacent to the wall on the upstream side."

Jan 1, 2016

By Charles G. Crans, Naresh Gurpersaud

"Toronto’s Union Station, a National Historic Site occupying an entire city block, is the busiest commuter rail transportation hub in Canada. An extensive project is being undertaken to revitalize Union Station while maintaining the historical significance of the building and minimizing disruption to commuters. A significant stage of the revitalization involves excavation indoors, to a depth of up to 5.5 m below the existing floor level to create space for a new transit concourse and a new lower-level pedestrian retail concourse. A hybrid excavation support system utilizing micropiles as soldier piles was constructed over an 18 month period between 2010 and 2011.Development and testing of connections between the micropiles, shotcrete facing, lagging, walers, and tiebacks presented significant challenges. The existing viaduct structure was constructed in the 1920’s on land reclaimed from Toronto Harbour, so there was significant (and ongoing) uncertainty with respect to buried obstructions including relic timber wharfs and abandoned steel and timber piles. Collectively all these conditions precluded the use of conventional methodology; new techniques, installed using modified equipment, and for the first time in the Greater Toronto Area, were required.Details of the existing site conditions, installation challenges, design, construction and performance of the hybrid excavation support system inside this historic structure are presented.INTRODUCTIONUnion Station in Toronto, Ontario is the busiest passenger rail facility in Canada, with 65 million passengers annually and an average of 200,000 passengers each day. Construction of the station was completed in 1920. It has been designated a National Historic Site of Canada and inducted into the North America Railway Hall of Fame in the Facility and Structure category.The Union Station Revitalization Project (USRP) was tendered in 2010 and awarded as a 6-year, $450M construction management / trade contract package. Included was a large scale grade reduction, referred to as “The Dig Down”, to create two basement levels and this required extensive excavation support constructed entirely indoors within the active station setting."

Jan 1, 2017

By B. De Paoli

At Pietrafitta, between Assisi and Perugia, ENEL (Italian National Electricity Authority) has for some time been managing a power-station operated with lignite, mined from an open mine on the way to exhaustion. A new plant is under construction which is located in the mine that was filled with tailings, mainly clays, sandy silts, lignite and ashes produced by the power-station. The soil profile is shown in Fig. 1: the thickness of the made ground is around 27 m. The foundation of the new power-station is on 320 t piles, 1.20 m diameter, embedded in the cohesive base formation at a depth of 57.5 m. 2,350 piles will be constructed for a total length of 125 km. It is therefore one of the largest pile sites at present in operation in Italy. [ ]

Jan 1, 1994

By Lance Rasband, Richard Hanke, John Starcevich

"The 17.4 meter (57 ft) diameter tunnel boring machine (TBM), the world’s largest at the time of her launch in 2012, locally referred to as “Bertha,” is stuck. Incapacitated due to mechanical failure approximately 36 meters (120 ft) beneath downtown Seattle, situated precariously between the deteriorating Alaskan Way Viaduct and the failing Seattle Seawall. Accessing Bertha with a vertical shaft provides the best approach to address all facets needed for repairs and will allow the full removal of Bertha’s cutter head and related inner workings. Limited area above the tunnel alignment and the physical restrictions of existing infrastructure, create significant challenges for the design of an otherwise symmetrical shaft, requiring special attention to design and layout. Consequently, the access/recovery shaft design required a combination of 3m, 2.5m, 2.2m, 1.5m and 1m diameter unreinforced drilled secant piles coupled with various ground improvement techniques and dewatering, to fully satisfy the shoring design requirements. This paper will describe the shaft installation procedures, equipment used and pitfalls encountered while undertaking access shaft construction of this magnitude.INTRODUCTIONTunneling on Seattle’s SR99 tunnel project began in July of 2013. After slowly mining through a 4.5 m (14.76 ft) thick fiber-reinforced concrete headwall and the first of three stabilized “safe havens,” Bertha would proceed along the proposed alignment through 122 meters (400 ft) of jet grout improved soil at a rate of slightly over 1.6 m (5.25 ft) per day. Once past the improved area, it was planned that “Bertha” – would be moving at a rate of about 11 m (36 ft) per day. By the end of October 2013, Bertha had mined roughly 131 m, (430 ft) averaging 1.4 m (4.6 ft) per day and had begun mining within native soils. By December 2013, tunneling had reached the 244 m mark and Bertha was averaging 3.6 m (11.8 ft) per day, achieving as much as 12.8 m (42 ft) of progress on given days. Unfortunately, on December 6th, 2013, Bertha began to stumble and all progress quickly came to a halt.It was initially reported that an obstruction had stopped Bertha in her tracks. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic pressure around the TBM, and allow visual inspection of the cutter head from within the TBM, and also to investigate for the presence of obstructions at the face of the cutter head. During this inspection, fragments of steel pipe were discovered entangled in the cutter head. The fragments were apparently from an abandoned 254 mm (10 in.) diameter monitoring well casing, previously installed by WSDOT to monitor ground water conditions for the design and planning of this tunnel project. After the steel was removed from the cutter head and cleared from Bertha’s path, tunneling resumed. It was then discovered that Bertha was only able to generate a slow crawl."

Jan 1, 2016

By Ramin Motamed, Anna Panorska``, Joseph A. W. Toth

In this study, a dataset of 145 bi-directional and static load tests was used to evaluate the load-displacement response with respect to unit side resistance for drilled shafts comprising fully and partially mobilized data. A total of 612 unit side resistance curves were calculated which included 52 fully mobilized curves showing a maximum response. A new approach using the double tangent method, is proposed in calculating the maximum unit side resistance from partially mobilized load-displacement data. The double tangent method was applied to each load-displacement response to estimate the ratio of mobilized resistance between the intersecting tangents and peak measured resistance. It is observed that as the mobilization of side shear approaches a maximum, the ratio approaches unity. Using the fully mobilized curves, regression models were developed using correlations between ratios of estimated resistance at the double tangent, peak, and maximum measured responses. Regression models are evaluated for the following factors: predominant soil type and drilled shaft construction methods. Comparisons of calculated and measured maximum values of unit side resistance are compared for each model. Although these factors each influence the load-transfer behavior, a single global regression model including all the data showed promise in yielding accurate results.

By Jim Bruce, Naresh Gurpersaud

"The West Toronto Diamond project, under construction since 2006 and due to be complete in 2015, is a rail-to-rail grade separation project in the heart of urban Toronto. Once complete, a depressed corridor over 1000 metres long will take the CN tracks beneath the CPR tracks. An interlocking steel pile wall serves to retain ground and cut off groundwater. Remedial measures, constructed using jet grouting, were required at several locations within and behind the steel piles.At mechanical interlock joints damaged or suspected of being damaged, jet grouting was used to improve native soils on the retained side of the wall to reduce permeability of the soil mass in intimate contact with the joints to 10-7 cm/s. At a number of steel piles where groundwater and soil type combined to cause basal instability inside the pipes during the interim between excavation and concreting, jet grouting was used to construct temporary bottom seals. At locations near adjacent structures where the steel pile installation process resulted in disturbed ground on the retained side of the wall, jet grouting was used to strengthen and stabilize ground.This paper outlines the details of the various jet grouting applications, the respective testing programs implemented to demonstrate in situ permeability and strength of the soil-grout matrix, and performance of the constructed system.INTRODUCTIONThe West Toronto Diamond (WTD) is a junction of several railway lines, all intersecting at the same grade (Figure 1). A major grade separation project at this site commenced in 2006 and is scheduled to be completed in 2015. The whole of the work is comprised of multiple contracts, completed and/or ongoing, by different constructors. Once completed, a depressed corridor over 1000 metres long with over 23,500 m2 (face area) of retained earth will bring the CN tracks beneath the CPR tracks and eliminate a major bottleneck at the most heavily used rail crossing in Canada."

Jan 1, 2017

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By Ziyad Abunada, David O’Connor, Fei Jin, Abir Al-Tabbaa

"In-situ remediation of contaminated land with deep mixing can enable a multi-technique remedial strategy on the same site combining low permeability barriers, permeable reactive barriers, stabilisation/ solidification treatments as well as ground improvement, delivering significant advantages over alternative strategies. This was the core objective of Project SMiRT (Soil Mix Remediation Technology) which involved the execution of the largest research field trials in the UK to date to provide field validation for this technique. Around 800m3 of soil were treated on a contaminated site in Yorkshire in May 2011 with 6 different treatments, testing ~40 binder compositions and 10 different installation methodologies. Field monitoring, testing and coring activities at the site took place within the first 2 months after treatment and then again at 34 months after treatment. This paper presents an overview of the field activities to date and some 3-year results and assessment of a subset of the treated soil sections. Some good correlations are seen together with some clear differences between treatments. There is generally an observed consistency with depth, with the mixing effectiveness having a more profound effect than the binder composition or content, within the tested materials and ranges. These field trial activities are currently being used in the development of the full-scale commercial remedial strategy for the site.INTRODUCTION AND OVERVIEW OF PROJECT SMiRTWhile there are strong financial and environmental incentives to remediate and redevelop brownfield sites there are also barriers including fear of the unknown, regulatory control, delays, increased costs and the stigma associated with such sites. Hence the remediation process needs to be conducted in such a way to maximise the incentives and overcome the barriers, which is how deep mixing found its niche in the land remediation market. Soil mix technology is such a versatile technique that can perform a number of remediation treatments on the same site. These include low permeability in-ground barriers (cut-off walls), permeable reactive barriers (PRB), stabilisation/solidification (S/S) treatments, other additive related remediation, e.g. in-situ chemical oxidation and bioremediation, as well as soil amendments for greening and also ground improvement all on the same site (Al-Tabbaa et al, 2011). Placed in the context of alternative solutions, soil mix technology could potentially replace the five techniques shown in Figure 1, which would be required to deliver the same treatments mentioned above. Treatment trains strategy, where a combination of techniques in succession are used to both reduce the contamination levels and deal with residual contamination, is becoming common in land remediation and the use of one set of equipment to deliver this would bring about significant financial advantages. In addition, soil mix technology has many other advantages in terms of speed of implementation, elimination of exposure to contamination, elimination of off-site disposal and low cost. Soil mix technology for the remediation of contaminated land emerged in the UK in the mid 1980s and has since been employed in over 30 or so projects, which far exceeds its application to ground improvement for which only a handful of jobs have been carried out to date."

Jan 1, 2015

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By Brian W. Wilson

A case study is presented that describes the design and implementation of a combined blast densification and deep dynamic compaction program which was undertaken to improve the foundation soils for a proposed tailings dam raise in Ontario, Canada. Based on the results of the geotechnical investigation it was determined that the foundation of the dam would be situated on tailings of both variable thickness and density, much of which would be susceptible to liquefaction under the design earthquake for the region and type of facility. Blast densification trials were completed by the owner and the results of these made available to prospective tenderers in response to a call for a fixed price contract for the design and implementation of a densification program for approximately 800,000 m3 of foundation tailings. The variation in tailings gradation and the impacts of such on the ground improvement program are discussed, as are details of both the additional blast densification field trials completed by the contractor, and the selected blast pattern and explosive charging used for production blasting. The applicability of the various ground improvement techniques to the actual conditions encountered, and the results obtained are also discussed.

Jan 1, 2010

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

By Vivian M. Troughton, Clifford J. Wren, Tony P. Suckling

"Secant pile walls are used for the construction of deep basement walls and earth retaining structures. Risk associated with secant pile walls is commonly perceived as being the safety of site personnel and the public during piling operations, or safety used in design. It is recognized that both of these are of paramount importance, but additional risks associated with the construction methods must also be considered to complete the risk management profile for any project. For the particular case of secant pile walls, if Clients take a ""back seat"" they may be unaware of the total risk package they are procuring. The authors argue that the piling contractor should be involved at the earliest stage giving input into the overall risk management process. Such early involvement within the professional team will maximise cost benefits to the Client and minimise the delays and cost increases sometimes associated with these works. A consistent methodology for identifying and then managing all the risks associated with secant pile walls is proposed. An example is used to demonstrate how this methodology should be employed. INTRODUCTIONThis paper discusses the value of a complete and integrated risk management process for structures with basements formed using a secant pile wall.The risk associated with any secant pile wall can be consicfered as comprising four components;1. Safety of people on site2. Safety of design or design methodology3. Construction risks4. Commercial risksAny risk management system needs to fully consider and integrate each of these four components to maximise the likelihood of a successful outcome for the basement.This paper concentrates on the construction risks for secant pile walls, as these are not often understood by the Client (in this paper the term ""Client"" also includes the main contractor, principal contractor, Engineer, Planning Supervisor, quantity surveyor and cost consultant)."

Jan 1, 2005