Search Documents

By B. W. Raymond, D. W. Zandee

"IntroductionCoal deposits are found in many regions in Canada and vary widely in their age, quality and rank. All classifications of coal except anthracite are found in significant quantities in this country.Deposits in the Maritimes are mainly bituminous; Lignite is found in Saskatchewan and Ontario and sub-bituminous coal in the plains region of Alberta. The Rocky Mountain coalfields of Alberta and British Columbia contain low and high-volatile bituminous coal and, in a few places, semi-anthracite. The British Columbia interior contains deposits of semi-anthracite, bituminous, sub-bituminous coals and lignite. The Yukon and Northwest Territories also contain substantial deposits of bituminous coal and lignite.Currently Nova Scotia produces both thermal and metallurgical coal, Saskatchewan produces lignite and Alberta produces both sub-bituminous and bituminous coal for thermal purposes. Large deposits of metallurgical coal are now being exploited in the Rockies arefl of British Columbia and Alberta by open pit methods. The raw coal is treated in large capacity preparation plants to remove refuse and upgrade the product to a consistent metallurgical quality with respect to ash, moisture, volatile matter and coking properties.The treatment of coal involves crushing, screening and cleaning by dense medium, jigs, water-only cyclones, tables and froth flotation to produce a diverse range of coal products differing in quality and size for various end uses.The chapter on Crushing and Screening Circuits was concerned mainly with crushing of metalliferous ores to produce a concentrate of one or more valuable minerals which normally constitute a small portion of the original mass of the material treated.Coal differs physically from ores in many ways such as lower specific gravity, relatively large volumes but low tonnage of product, and its habit of absorbing moisture requires extensive dewatering processes more complicated than settlement and filtration. Most significant, for this paper at least, is the fact that crushing coal is not as energy intensive and much smaller equipment is applicable.Crushing and screening of ores is intended to reduce the size of all constituents as quickly and efficiently as possible to allow liberation of the mineral particles. The crushing of coal is different in that the coal is not the minor constituent and the production of fines, in the initial stages at least, is highly undesirable. The basic objectives of crushing coal are the reduction of run-of-mine material to sizes suitable for cleaning or further reduction of coal to market sizes."

Jan 1, 1989

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By D. Chakravarty, B. Samanta, D. Ghosh

Autonomous robots are useful for 3D underground mine mapping to avoid human exposure to hazardous spaces. To prepare a precise mine map, a self-navigating robot must navigate an arduous path, avoiding obstacles and sensing the environment. A prototype laboratory-scale robot was built and evaluated through a mock-up in a test mine gallery. It was outfitted with a 2D laser scanner, a stereo camera for obstacle avoidance, and a high-precision, laser-based imaging and digitizing system for collecting 3D point cloud data. Various algorithms were used for scan matching to facilitate simultaneous localization of the robot for mapping.

Jan 1, 2014

By J .. Carignan, Y. Dembele, J .. Guha, A. Fowler, A. Gobeil

The Barlow Lake stratigraphic section comprises the top of the Gilman Formation, the Blondeau Formation and the three sills of the Cummings Complex. Representative samples were analysed to allow characterization of the chemo-stratigraphic profile and geochemical affinity of the six rock facies found in the section. All the mineralized horizons are associated with sedimentary units. Geochemical signatures associated with the mineralizations are either very weak or very localized and shown by increases in K20 around the mineralizations and Fe203 near them. The mineralizations are stratiform, synvolcanic but resedimented and remobilized by regional metamorphism and possibly by hydrothermal activity initiated by the intrusion of the Cummings Complex. The evolution of the sedimentary basin with the decrease of its depth is confirmed by the chemo-stratigraphic profiles. Stratigraphic position in the section is important in order that the chemo-stratigraphy may serve as a guide for mining exploration in the distal facies of the Blondeau Formation.

Jan 1, 1984

By John A. Allan

The subject chosen for this paper is not a new one, but the subject matter is so extensive that something new can always be said .about it. We are just beginning to realize how little is actually known about the character of Alberta coal, except for a few general facts. The object of this paper is not to explain that our previous information, in whole or in part, on the coal resources of Alberta, has been incorrect, but rather to present some new facts obtained as a result of recent study in the field and in the laboratory. As field investigation continues the problem of determining the character of a coal seam for any great distance laterally becomes more and more complex. Our present knowledge of Alberta coal deposits should not be discussed before due reference is made to those great pioneers who blazed the trails for later geologists, by recording their observations on the general geology of Alberta. Geologists, to-day, particularly those of us who are striving, year after year, to unravel the mysteries of stratigraphy, palaeontology, and structure, in so far as these are related to the coal resources of Alberta, fully realize our indebtedness to those three trail-makers, Dawson, McConnell, and Tyrrell. Had these geologists not recorded their observations correctly, nor interpreted the broad geological facts contained in Nature's book, with still uncut pages, how much slower would have been the progress of our coal knowledge in the succeeding years. It is true that many of the interpretations given to observations by these pioneers have had to be changed as a result of closer studies, but we must also expect that the geological interpretation from present day observations will be changed by future workers, as Nature's book is read and re-read.

Jan 1, 1925

By A. Tohn, L. May, Adham. K.

The path from process conception to commercial implementation poses significant technical, economic, and sometimes political challenges for every project team. Solving the technical challenges typically distinguishes successful projects from those that fail. Here, the authors provide an outline for technical success based on lessons learned from years of experience in process design and R&D. Challenges faced by new technology developers, with regard to design and definition, are described. Experience-based methods to avoid missteps are shared. Special emphasis is placed on the selection of viable unit operations, definition of known and unknown parameters, experimental screening of options, and piloting for scalable design information. Use of computational models to define, assist, and interpret the pilot operations and results are described. Furthermore, the value of active collaboration amongst the design, research, and owner team is demonstrated.

Jan 1, 2011

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By Tamas Kekesi, Gergo Rimaszeki, Tibor Kulcsar

The efficient purification of soldering waste material can be achieved in a single operational step by the electrolytic refining in pure hydrochloric acid - tin-chloride media. The complex formation of the ionic species may offer a beneficial level of natural inhibition. Using the PCR (periodic current reversal) technology, is efficient in affecting the morphology of the cathodic deposit. In order to optimize the process, the investigation of the solution stability and the electrode reactions is essential. The natural tendency of the Sn(II) oxidation and precipitation can be overcome by properly controlling the concentration of the main components and the ratio of Sn(IV)/Sn(II) in the electrolyte solution. Polarization curves were obtained for different concentrations tin and hydrochloric acid. Conclusions referring to the electrode reaction were derived from the overvoltage - current plots. The morphology of the deposit can be correlated with the exchange current density, also determined from the polarization curves. The cathodic current efficiency and the morphology of deposited metal are affected by the distribution of tin species and the principal electrolysis parameters.

Jan 1, 2011

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005

By C. Ayora

The Iberian Pyrite Belt (SW Spain and Portugal) contains one of the largest reserves of pyrite in the world with mining activities dating back to prehistoric times. About one hundred abandoned mine wastes and galleries release a huge acidity and metal load to the Tinto and Odiel rivers. Once the mining activity is over, polluting discharges can persists for decades or even centuries with no specific responsible entity. In-situ passive remediation technologies are especially suitable for these orphan sites. The concept is to insert a reactive porous material in the natural flow path of contaminated surface and ground waters, and it is implemented through infiltration ponds and reactive barriers, respectively. Calcium carbonate pea-size gravel is the common alkalinity supplier to neutralize acidity and precipitate metals. These remediation systems have been traditionally implemented in coal mines. However, the acid drainages from the Iberian Pyrite Belt contain metal concentrations one to two orders of magnitude higher than those from coal mines and require special designs to avoid quick clogging or passivation (coating) of the grains of reactive material. To overcome these problems, a Dispersed Alkaline Substrate (DAS) mixed from fine-grained limestone sand and a coarse inert matrix (e.g. wood chips) was developed. The small grains provide a large reactive surface and dissolve almost completely before the growing layer of precipitates passivates the substrate. The high porosity and the dispersion of nuclei for precipitation on the inert surfaces retard clogging. However, limestone dissolution only raises pH to values around 6.5, which is sufficient to precipitate the hydroxides of trivalent metals (Al, Fe), but it is not alkaline enough to remove divalent metals. Magnesium oxide, which hydrates to Mg hydroxide upon contact with water, buffers the solution pH between 8.5 and 10. A DAS system replacing limestone with caustic magnesium oxide has been tested to be very efficient to remove divalent metals (Zn, Cd, Mn, Cu, Co, Ni, Pb) from drainage previously treated with limestone.

Aug 1, 2013

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By W. A. Jones

THE Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is situated near the north end of lot 1, concession 2, Hislop township, Ontario. The property comprises the north half of lot 1, concession 2, and the south one-third of lot 1, concession 3. It is readily reached by a good motor road from the village of Ramore, 7.5 miles to the southeast on the Temiskaming and Northern Ontario railway. The-mine has been developed to a depth of 900 feet and the current daily production rate is about 260 tons. From the inception of operations in March, 1935, until December 31st, 1942, 455,720 tons of ore with a total value of $4,169,-316 have been milled. The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines. The deposit is interesting because the relationship between hydrothermal metamorphism and three successive stages of fracturing and mineralization is marked with considerable clarity. During the past seven years, detailed geological maps of the mine have been kept up to date, many thousands of feet of diamond-drill core have been logged, and numerous thin and polished ore sections have been studied. The present paper describes the structure and mineralogy of the orebodies.

Jan 1, 1944

By J. Aydt, W. McCombe, H. McLaughlin, L. Nightingale-Mercer

The McClean Lake mill is located approximately 850 kilometers north of Saskatoon, Saskatchewan, Canada and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and in 2014 completed a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum. This expansion included significant changes to the mill’s secondary leach circuit in support of safely processing high grade ore directly from the Cigar Lake mine. In particular, inter-stage pumps were introduced for slurry transfer between the secondary leach tanks, replacing the original pressure feed forward operation. The design and selection process for these pumps was strongly influenced by the uncertainty related to actual radiation dose exposure when processing undiluted high grade ore (up to 30%U), and consequently the desire to maintain minimal occupancy in the vault enclosure containing the secondary leach tanks. These constraints resulted in the decision to install positive displacement pumps above the leach tanks in a suction-lift configuration. Operating experience with this design has shown that the pump capacity is significantly de-rated due to process solution gas-entrainment and pipe scale build-up, particularly in the front end of the secondary leach circuit where reagent dosage is high. Experience processing high grade ore also provided accurate radiation dose data to demonstrate that the level of occupancy in the leaching vault enclosure could be re-evaluated to accommodate alternate pump configurations. This paper reviews the lessons learned and improvements made to safely increase the capacity and reliability of the leach inter-stage pump system.

Jan 1, 2020

By M. H. Govett, G. J. S. Govett

"The current American ""energy crisis"", occurring in the midst of a global debate on the adequacy of mineral supplies to support present and projected levels of world consumption, has focused attention on Canada as a major world producer of minerals. Exports of minerals account for approximately one-third of Canadian foreign earnings; more than half of these exports are to the United States. Although the United States is a net importer of most industrially important metals, with the exception of nickel and zinc, only a small part of American mineral imports are from Canada; these imports are minerals for which geographical proximity and strategic considerations are important. In the short-term, Canada is more dependent on her exports to the U.S. than America is on imports from Canada. It is argued that Canada, far from indulging in economic nationalism to preserve her resources, should expand her exports while the markets are available."

Jan 1, 1973

An optimized long-term mine planning determines the best order of material extraction, so that the Net Present Value (NPV) becomes maximum. In the case of oil sands surface mining, one of the key constraints in NPV maximization is the volume of tailings slurry that will be generated downstream. Specifications of tailings slurry are also important from environmental perspective. Moreover, most of the material that will be used for the reclamation of tailings ponds in later periods is generated in extraction and processing of oil sands. In this paper, an integrated optimization framework is proposed to maximize the NPV of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. The proposed model is coded in Matlab and has been run using CPLEX for verification. The results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Aug 1, 2013

By S. Makni, S. Koppalkar, A. Bouajila

This paper reviews briefly the gravity recovery involving conventional gravity separators and centrifugal gravity separators. The advantages of semi-continuous gravity separators will be discussed. Techniques for upgrading the gravity concentrates will be addressed briefly. The research efforts in optimizing semi-continuous gravity separators will be recalled. Innovative gravity circuit for eliminating or minimizing the use of complex processing schemes will be reviewed. On-going gold gravity research at COREM has revealed that gold particle shape transformation is the main factor explaining the lower recoveries of the plant units. Efforts to devise possible remedies for improving gravity recovery at plant will be discussed.

Jan 1, 2011

By John F. Kearney

Labrador Iron Mines (?LIM?) Schefferville Projects consist of 20 major DSO deposits lying along a 120 km strike length in both the provinces of Newfoundland and Labrador and in Quebec. The town of Schefferville, Quebec lies close to the middle of this 120 km strike. LIM?s various properties comprise twenty different iron ore deposits which were part of the original Iron Ore Company of Canada (?IOC?) direct shipping Schefferville operations conducted from 1954 to 1982 and formed part of the 250 million tons of historical reserves and resources previously identified by IOC. LIM intends to develop all these resources in five separate stages. The first four stages will see the various deposits treated in three beneficiation plants, to be built adjacent to several of the deposits that comprise the Central, South Central and North Central Zones. The final stage is not yet planned but will likely involve a fourth plant. A Feasibility Study has not been completed on any of these Projects. LIM plans the development and mining of the various deposits in separate Stages. It should be noted that only the James and Redmond deposits have been permitted. All other deposits require environmental assessment and permitting. Only the James and Redmond deposits have been subject to detailed mine design. The Houston deposit has had preliminary mine design carried out. All other deposits will require detailed mine design when further geological data is collected and compiled. Detailed metallurgical testwork has been carried out on blue ore from James, Houston, Redmond and Knob deposits and to a more limited extent on yellow and red ores from these deposits. Only limited review work has been carried out on the high-silica blue ores. All of this work will be needed to be complete to confirm the final process routes. Additionally some metallurgical work will be required to be conducted on each of the other deposits to characterize their metallurgical response and to confirm expected recovery levels. Detailed mine design and metallurgical testwork has been carried out on those deposits that will form the basis of production for the initial years but further exploration, testwork and design is required for all the remaining resources. The first plant at Silver Yards and mine construction at James are now complete and initial production is expected in the spring of 2011. Metallurgical testing of the first stage deposits has established that the ore can be successfully upgraded to marketable standards. Based on the current testwork, a program of plant enhancement on the Silver Yards plant is now planned with the objective to increase both the plant throughput and recovery. Production of direct shipping lump ore and sinter fines is forecast at around 1.5 million tonnes in 2011 and, based on current and historical resources, growing to approximately 5 million tonnes in 2015 and thereafter. Production from the first four stages is expected to continue at about this rate through to about 2028.

May 1, 2011

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The business objectives of a metallurgical project determine targets and constraints, such as the range of products, production capacities, in-service dates, and capital and operating cost parameters. Permitting is usually left to the project team, as are decisions regarding site location, technology, and construction approach. Success requires an orderly methodology, represented in this book by front end loading (FEL) phases: FEL1 examines several alternative approaches; FEL2 ranks and eliminates less economically or technically attractive options; and FEL3 develops the preferred option to the point of major permit completion, with defined scope, schedule, and cost to submit for approval to proceed with implementation in FEL4. Working through FEL1, FEL2, and FEL3, the project definition improves, estimates become more accurate, and project risks are reduced. The project design basis at the end of FEL3 is the control document for project implementation in FEL4.

Jan 1, 2015

By H. H. Claudet

PROBABLY the first flotation mill for treating molybdenite ores was put into operation .in Norway during 1913, when the writer was employed to introduce and apply the Elmore vacuum flotation process at a mine in southern Norway. These operations proved successful and led to other similar installations in that country. It remained, however, for Norwegian engineers themselves to iron out their difficulties and establish the molybdenum industry on a basis which ultimately attained world importance. Just as today, an urgent demand for molybdenum arose during the world war of 1914-18. By 1916, many molybdenite properties were in operation in Canada and several small concentrating mills were under construction. At one of these, in the Ottawa Valley district, the opportunity came for applying the Elmore vacuum flotation process, using a flow-sheet similar to that adopted in Norway. Later, as one of the staff of the General Engineering Company, who had already developed a highly efficient flowsheet for treating molybdenite ores, using the Callow pneumatic flotation process, the writer devoted considerable time to research work and investigations on a number of molybdenite projects and deposits in eastern Canada. The bulk of Canada's production of molybdenite was coming at that time from the Moss mine at Quyon, Que., where concentration of the ore was effected by water-film flotation. It is of interest to note that this process, based on the principle of surface tension, had been developed and introduced by the late Henry E. Wood, of Denver, Colorado- one of the original owners of the Moss mine-at the time he was investigating the Elmore vacuum process in his Denver plant. The process, with certain modifications, was used at several other properties in eastern Canada, and notably in the ore dressing laboratories of the Department of Mines at Ottawa and in a plant at Renfrew, Ont., in both of which ore from deposits in various parts of Canada was treated, with recovery of very appreciable amounts o much needed molybdenite. During the summer of 1917, the water-film flotation mill at the Moss mine was dismantled and the plant was re-modelled by the General Engineering Company to include the Callow system. This installation, using improved flotation methods, was highly successful both as to recovery and grade of concentrate, and proved a decided advance in molybdenite concentration, a recovery of upwards of 90 per cent being obtained, with a concentrate grading over 90 percent MoS2.

Jan 1, 1944