Search Documents

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By R. P. Hackl, P. G. West-Sells

Carbonaceous gold ores are particularly attractive for leaching by ammonium thiosulfate as the gold thiosulfate complex is not significantly adsorbed by the organic carbon present in the ore. A technically and economically feasible process for treating these ores with ammonium thiosulfate has been developed. In this process, gold is extracted by leaching the ore with ammonium thiosulfate, the solution is separated from the ore by counter - current decantation, the gold is recovered by precipitation with ammonium sulfide, and finally the gold containing product is upgraded by reacting the elemental sulfur present in the precipitate with ammonium sulfite. The precipitation filtrate is recycled back to the grinding step to close the solution balance. Reagent consumption is not excessive. Besides precipitating gold, the precipitation step removes most deleterious solution impurities and converts a portion of the polythionates back to thiosulfate. This paper discusses the optimization of the leaching, precipitation, and upgrading steps. The results of a 10 kg/h pilot plant campaign are also discussed.

Jan 1, 2005

By L. Bichler

Utilizing thermal analysis techniques, pioneering research into the solidification mechanism of a popular magnesium alloy AZ91E cast by the Lost Foam Casting (LFC) process was carried out, Foam characteristics, section thickness and application of vacuum were seen to have profound effect on the cooling rate, thermal gradients and casting temperature profiles.

Jan 1, 2005

By J. Schmidt

The development of set of laboratory experiments, intended to help undergraduate students meet Canadian Engineering Accreditation Board requirements for Engineering Design outcomes, is described.The laboratory, which is part of a third year level course in hydrometallurgy, is aimed at advancing the ability of students to generate and use experimental results to design an industrial copper leach/SX/EW plant. Emphasis is placed on the students demonstrating the ability to use of their engineering knowledge in weighing the pros and cons of the various process options that they test in converging to a final flowsheet. INTRODUCTION Over the past number of years the Canadian Engineering Accreditation Board, CEAB, has dramatically shifted the way that they evaluate undergraduate programs. In the past, the focus was on measuring of the quantity and quality of material the students were intended to learn as well as the methods and resources used to deliver that material. Now, rather than principally evaluating the inputs of programs, the focus is more on measuring the quality of the outputs from the programs, i.e. the quality of graduating students. In this regard, the CEAB has developed a list of twelve attributes that learners must develop in the course of their studies. Engineering programs must, not only demonstrate that their curriculums provide opportunities to develop these attributes, but must measure student proficiency in each of these attributes as they progress toward graduation. One particular graduate attribute that Laurentian University’s Bharti School of Engineering has encouraged its faculty members to develop content for is “design”. Engineering Canada (2018) defines this attribute as “an ability to design solutions for complex, open-ended engineering problems and to design systems, components or processes that meet specified needs with appropriate attention to health and safety risks, applicable standards, and economic, environmental, cultural and societal considerations”. The previous laboratory component for the hydrometallurgy course was a collection of unconnected experiments covering leaching, solvent extraction, ion exchange, and electrowinning. Like in other undergraduate courses, students would perform stand-alone experiments, make the specified measurements, do the specified analyses of the results, and report the findings, all as strictly detailed in the lab manual. The vision for the new lab was to create an experience that would more closely mimic an industrial research program whereby students would start with a given feed material and would progress through a series of connected experiments. Emphasis is placed on the student demonstrating competency in, not only, generating and analyzing experimental data, but also in using the data along with their engineering knowledge to design and evaluate the pros and cons various plant configuration options. Principally, students are asked to weigh cost, safety, and environmental concerns in converging to their final flowsheet. In designed the leach circuit, students must weigh the costs/benefits of varying leach temperature. Higher leach temperatures will yield faster and more complete copper dissolution, which will allow for the specification of relatively smaller leaching circuits, saving capital costs. However, hotter acid solutions are more dangerous to handle and require increasing amounts of energy to heat the slurry, increasing operating costs. In solid/liquid separation, students must weigh the pros and cons of the addition of a flocculent to assist settling. The flocculant will allow for the design of a thickener circuit that employs units with a relatively smaller area, but will result in a thickener underflow with a lower pulp density, which may necessitate a larger number of thickeners. In addition, the environmental concerns of producing a tailings product that contains an organic contaminant should be addressed. In solvent extraction, students must specify the number of stages of loading and stripping, as well as organic and aqueous flowrates to produce suitable raffinate and rich electrolyte streams. Finally, in electrowinning, students will compare the costs/benefits and risks of the use of precious metal coated titanium dimensionally stable anodes (DSAs) versus conventional Pb based anodes.

Jan 1, 2019

By Philip Peck

Mine closure issues ?Narrow issues: ?Environmental focus; ?Broad issues: ?Social issues and sustainability; ?Continued importance of mining; ?Historical legacies from closed mines; ?Barriers to development; ?Migration [ir]reversibility Dealing with closure issues ?A matter of choice ?Option 1: Engagein solving closure problems as best possible; ?Option 2: Exit, leaving the playing field to firms not interested in solving problems ?Option 3: Delay, till better time to enter or until early entry [by others] fails and pick property up cheap [?].

May 1, 2006

By Jo Render

Expectations of your management approach ??Life of mine applicability ??Tailor scale of activity to scale of project ??Assess impacts, risks, and opportunities ??Use global good practice, backed up by rigorous analysis ??Support with trained monitoring and evaluation team ??Information infrastructure to allow ongoing trend analysis and tracking of progress ??Public reporting using standardized indicators Yes, we are talking about a ?management system?

May 1, 2011

By Andreea Catalina Gluhoi

Oxidation and reduction reactions of N-containing molecules have been studied over different types of gold-based catalysts, Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 (M, MI, MII=Li, Rb, Mg, Ce, Zr, Mn, Cu) prepared by deposition precipitation with urea. In general, all the catalysts were already active at low temperatures. NH3 oxidation was effectively catalyzed by Au/CuO/Al2O3, a catalyst which also gives the highest yield in N2. NO reduction by H2 performed over gold-based catalysts produced N2O, N2 and NH3 and N2O reduction resulted in the formation of dinitrogen. For all the reactions, large synergistic effects have been obtained by addition of different kind of additives.

Oct 1, 2003

By Davis Myers

OVERVIEW ?A summary of population demographics data ?Potential impact of Baby-Boomer, Generation X, Millennial demographics in the mining workforce ?Planning with constrained resources Age Cohorts ?Baby Boomers: born 1946 -1965 ?Booming economy, TV, cold war, JFK, Vietnam ?Generation X: born 1965-1980 ?There was always space travel ?PC?s, Black Monday, Challenger, Desert Storm, fall of Berlin Wall ?Millennials: born 1980-2000 ?There was always the internet ?IM, Facebook, Sept 11, Columbine

Nov 1, 2011

By Lindsay A. Robertson

The long term management of acid generating tailings at mine closure is a common issue, however, management of ARD is significantly impacted by local conditions, including climate. Acid generating tailings, over time, will produce acid rock drainage (ARD) if left exposed to water and air, which both contribute to the sulphide oxidation process. The long term closure of tailings storage areas is a concern from both environmental and engineering perspectives, with long term acid generation and dam stability the main risks. Several approaches can be taken to minimize ARD from tailings facilities using cover systems. Three tailings facility cover case histories, in areas of net positive water balances, were investigated using unsaturated flow modelling software to determine the long term potential for limiting ARD by increasing saturation of the tailings and decreasing oxygen ingress. Each case study demonstrates the importance of integrating the tailings dam engineering into tailings cover closure design. Model predictions are compared to measured saturation levels to assess the accuracy of the calculations.

May 1, 2011

By E. C. De Matos

The Uranium Province of Lagoa Real is located in the mid-south region of Bahia State, Brazil. Uranium is the only mineral wealth, occurring mainly in the form of uraninite. The region has been searched for uranium since 1971 and 35 anomalies were detected, distributed over 1200 km2. Seven are now taken as deposits, accounting for reasonably assured resources of 100.000 tons of U3O8. This paper describes the geological aspects of the area, the exploration and mining activities done so far by the state company INB and the perspectives for the near future, when a raise in the country?s uranium demand is expected.

Aug 1, 2010

By Barbara Kirby

Mining Industry HR Challenges Mining industry needs to hire approx. 100,000 workers by 2020 Attraction and retention of talent in all occupations Mobility of skilled workers between mine sites 70 percent of employers expect labour shortages over the next 5 years. Largest shortages: -physical sciences and engineering occupations -trades and ?undesignated? occupations ?Undesignated? Occupations ?Undesignated? Occupations -eg. mill operators, production / development miners and heavy equipment operators More than 20,000 workers will be needed by 2020 in the undesignated occupations and another 11,500 tradespersons Turnover rate for trades and undesignated occupations at mines is high: 8.3% compared to 5.6 % for all other occupations There is no system to recognize the skills of high-demand undesignated occupations

May 1, 2010

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

IBI Alliances ? Government ? People ? Academic ? Associations ? Media ? Customers ? Agencies ? Shareholders ? Industry consultants ? Investment Authority ? Geological Survey ? Department of Mines ? People ? Local Residents ? Mineworkers ? Academic ? University of Guelph ? Uganda Vermiculite Institute ? Associations ? TVA ? Organic Certification ? Media ? Canada ? International ? Customers ? Advocacy role ? Agencies ? Regional International

May 1, 2006

By Jan Nemcik

Among other products steel mesh has been used successfully for many years to support strata and minimise loose material from falling into the mine opening. Installation of steel mesh has proven to be difficult to automate and many other products, such as Thin Spray-on Liners (TSL), have been proposed as a replacement. Ideally, the mechanical properties of these products should be superior to those of the steel mesh, however, most TSL trialled in mines to date have been weak and in addition have had slow cure times, as a result none of these materials can seriously compete with steel mesh. Now a new polymer product that cures in seconds and forms a stiff strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong. To enable selection of a suitable polymer material for roadway skin reinforcement several numerical models were constructed to investigate the role of interface roughness and the influence of polymer stiffness on load transfer along the rock-polymer interface. Laboratory tests indicate that the shear adhesion of the rock-polymer interface can be substantial while the tensile adhesion can be much lower. The models indicate that the natural stone roughness and surface waviness plays a major role in shear adhesion while the elastic properties of polymer liner can significantly influence the polymer ability to resist fracture opening.

Oct 1, 2009

By F. Rosenblum, P. Spira

A laboratory test has been developed for assessing the patential hazard from self-heating of sulphides. The technique consists in measuring the rate of self-heating, from near ambient temperature, of a 1-kg sample in an insulated chamber controlled at standard atmospheric conditions. The rate of oxygen consumption is monitored simultaneously. The paper describes the apparatus and test procedure, and reports data on various ores and mill products. Tailings known to have caused problems underground when used as backfill have shown heating rates of over 3°C/h. A preliminary hazard rating guide for backfill based on the known behaviour of several sulphide materials is presented.

Jan 1, 1981

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By L. A. Gomieroa

The Caetité-Brazil uranium facilities produce about 340 t/y of uranium from an ore averaging 0,25 U %. The process steps are ore crushing, heap leaching with sulfuric acid, U separation and purification by solvent extraction with tertiary amine followed by stripping with sodium chloride solution and precipitation as ammonium diuranate that is dryed. A change in the milling process is being evaluated to increase the production and the uranium recovery. Heap leaching will be changed to conventional tank agitated leaching of the ?590 ground ore slurry in sulfuric acid medium. The replacement of the stripping reagent is also being considered.

Aug 1, 2010

By Patrick Chabot

Ce document présente une méthode hybride de long trou favorisant une méthode de minage initiale par chambre-magasin et complétée par une méthode de minage long trou. Cette méthode a été adaptée suite à plusieurs facteurs tels qu?une géologie complexe, une rareté de mineur d?expérience et un haut taux de roulement de main d?oeuvre spécialisée. Cette méthode a permis d'excellents résultats par rapport à la dilution. De plus, la récupération de pilier à haute teneur par forage long trou sera expliquée. Cette méthode permet aussi de récupérer le minerai qui est resté accroché dans les chantiers chambre-magasins. Introduction : La mine Géant Dormant est une mine filonienne d?or située à environ 80km au nord de la ville d?Amos au Québec. Elle est en opération depuis 1988 et à la fin de 2007, elle a produit près de 885 000 onces d?or à partir d?environ 2 400 000 tonnes de minerai pour une teneur moyenne d?environ 11,5g /t Au. Cette mine est la propriété d?IAMGOLD Corporation depuis l?acquisition de Cambior par cette dernière au mois de novembre 2006. Elle emploie 151 employés permanents et environ 41 entrepreneurs.

Feb 1, 2008

By Cheryl L. Allen

Increasing energy costs associated with mining have become an issue that must be addressed by industry to ensure sustainable production. As underground mine ventilation systems account for 40% to 50% of a mine?s total energy requirement, initiatives to maximize their efficiency have been introduced worldwide. A control method known as Ventilation-On-Demand (VOD), which adjusts the ventilation system by responding to the activities of mine personnel and air quality, has been commissioned at Vale?s Coleman Mine. This initiative is an effort to reduce energy consumption, maximize efficiency of the ventilation system while ensuring air quality. There are five control strategies that can be executed with the VOD control system in place at Coleman Mine: Manual real time control Time-of-Day Scheduling Event-based control Environmental control Activity Based Control/Tagging This paper describes the system, control strategies and impact on energy consumption and flexibility of airflow distribution as applied at Vale?s Coleman Mine.

May 1, 2011