Search Documents

By Lloyd Buckingham

"The operating cost of a gold mine employing granular activated carbon to recover gold can be greatly affected by the condition of in-circuit carbon and its attrition losses. To accurately identify and quantify carbon losses requires careful study. Carbon attrition in the mill can be attributed mainly to physical or mechanical breakage due to the transfer of carbon in the circuit and to carbon oxidation and thermal fracture occurring in the carbon reactivation kiln. Of the equipment involved in carbon transfer, the water powered eductors are the major cause of abrasion and should be replaced with pumps or alternate methods that can serve the purpose. This paper also reviews the impact of carbon stripping and washing on overall operations.IntroductionHolt-McDermott Mine operates a 1360 tonnes per day Carbon-in-Leach (CIL) mill to recover gold. The relatively high carbon consumption and high remaining gold values on carbon after stripping were viewed as a challenging project for research. Extensive metallurgical testwork was initiated to reduce these values. Figure 1 below indicates the carbon flowchart prior to any significant changes in the carbon handling procedures.Carbon consumption after commissioning which was as high as 10""/o of carbon eluted, has been brought down to less than 5%. Changes that brought about this 50% reduction in carbon consumption are:1 ) Improvements in kiln operation2) Elimination or replacement of eductors3) Reduction in tonnes of carbon eluted"

Jan 1, 1994

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger.  The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. Conclusions and Future Work 1] The HMX based electronic initiation system permits bottom in-hole delaying in ground temperatures above 80°C (175°F). As compared to top priming and surface delaying, in-hole bottom delaying is known to improve floor quality, muckpile fragmentation uniformity and reduce oversize. 2] Field evaluation of the HMX initiation system at the Lihir Mine is continuing. 3] Work on the next generation of the HMX initiation system is underway and will bring with it expanded application range and flexibility. 

Oct 1, 2024

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997

By Z. Tang

A collaborative project was performed between NRC Institute for Fuel Cell Innovation and MagPower Systems Inc, to develop a cost effective fabrication process to manufacture the anode for magnesium-air fuel cell with improved performance. A novel fabrication process was developed, which resulted in a porous microstructure with increased surface area, instead of the traditional solid structure. This porous anode greatly increased power density in the magnesium-air power source. This fabrication process is very simple and cost effective. Especially, this process makes it convenient to incorporate different alloying additions, as well as hydrogen inhibitor and electrolyte management additive into the anode. The anode composition was designed so that micro galvanic cells were formed as current is drawn out of the fuel cell, and resulting increased dissolution rate of Mg. It is feasible to incorporate hydrogen inhibitor and electrolyte management additive into the porous anode, and the anode with some kinds of inhibitors exhibited improved electrochemical performance. This paper describes the microstructure and electrochemical performance of anodes with designated porous structure and alloying additions. Furthermore, quantitative kinetics analysis of the obtained I-V curves and electrochemical impedance spectroscopy were carried out to clarify the mechanism.

Jan 1, 2005

By David E. Pearson

"Western Canadian coking coals are located in the Rocky Mountains arid foothills of British Columbia and Alberta. They are typical of non-marine coals, characterized by total sulphur contents of less than one per cent and with ash contents of 10-30 weight per cent. This mineral matter is composed principally of kaolinite and quartz.The petrographic compositions of most of the coking coals which constitute the 2.065 billion tonnes of British Columbia's measured reserves, and the compositions of the metallurgical coal currently exported from Alberta, show them to be rich in the inertinite macerals, macrinite, fusinite and semifusinite. When the mean maximum reflectance of vitrinite in oil/Romax) is used as the coal rank parameter, this high inertinite content is reflected in the lower volatile-matter yields, but the relatively inert character is also displayed by lower free swelling indices (PSI), lower maximum dilatations, lower maximum fluidities and lower coke strengths than other coals of the same rank, but richer in the reactive macerals, vitrinite, exinite and semifusinite. Despite these reduced values in the so-called caking tests, inertinite-rich coals produce strong coke.A system of classification of coking coals is introduced which is based on rank, as indicated by Ro max, and either petrographic composition, maximum dilatation, maximum fluidity or, to a lesser extent, PSI and volatile-matter yield. Six principal coal groups can be distinguished among coking coals using this versatile classification. Inertinite-rich coals are assigned to the Keystone Group (GI), Balmer Group (G3) or Moura Group (G4), each group being named for a coal typical of that population ofcoals. Reactive-rich coals are assigned to the Pittston Group (G2), Kellerman Group (G5) or Big Ben Group (G6). A multiple-regression analysis of coal quality versus price shows how the value of coking coal in the Japanese market appears to be related to reflectance and the free swelling index, and confirms the economic viability of the classification.British Columbia's measured reserves of coking coal contain representatives of four of these groups; Balmer Group (73%), Moura Group (/6%), Pittston Group (3.4%) and Kellerman Group (7.6%).This analysis of the quality of Western Canadian coking coal indicates that despite the need for large proportions of inertinite-rich coking coal in blends produced in the Japanese steel industry, there is nevertheless a demonstrated overabundance of Balmer Group and Moura Group coals available to the international coking coal market."

Jan 1, 1980

By M. E. Hurst

Introduction Between 1903 and 1905, W. Mclnnis, of the Geological Survey of Canada, made a micrometer traverse of the Kawinogans (Crow) river from Kapkichegimaga lake to its junction with the Otoskwin river. He reported that a belt of Keewatin rocks, 1 to 4 miles wide, was exposed along the course of the river for 17 miles east of Kapkichegimaga lake. Prospectors and exploration companies paid little attention to the mineral possibilities of this belt until the summer of 1928 when, with the adoption of airplane transportation, the area became readily accessible. Within a short time widespread interest was aroused by the announcement of attractive finds, and a mild rush followed. During the winter months, hundreds of claims were staked on either side of Crow river for 12 miles east of Pickle lake. In the summer of 1929, much of this ground was systematically explored and a considerable amount of development work was done on the known deposits.

Jan 1, 1930

By H. Sano

Most of the dust generated from the copper smelting process in Chile has been stored after the stabilization by hydrometallurgical process because it contains high concentrations of arsenic. However, in recent years, the dust generation has increased because of degrading the quality of concentrate. In addition, the environmental regulations become stricter. On the other hand, valuable metals such as copper and zinc are contained in the dust at high concentrations and it is desirable to recover them. In this study, the effect of dust recirculation to the smelting process was examined in order not only to decrease the amount of dust but also to recover copper. Dust generation and the distribution of arsenic, lead, zinc etc. among the matte, slag and gas phases were evaluated as a function of the amount of recirculated dust, partial pressure of oxygen and temperature. It was found that the direct dust return to the smelting process was quite effective for the recovery of copper and the reduction of dust generation, but the acceptable dust amount was limited by the produced matte quality.

Jan 1, 2007

By C. Peña, C. A. Zaror, M. Bustamante, M. Vega

The goal of this paper is to present the carbon footprint of Chilean cathodic copper, as a function of the electricity generation mix, ore grade, and process efficiency. Ore grades and acid leach-solvent extraction-electrowinning (LX-SX-EW) yields in the range 0.5-1.0% and 60-80%, respectively, were considered here. Additionally, electricity supply from two Chilean suppliers, SING (1.0 ton CO2/MWh) and SIC (0.4 ton CO2/MWh) was assessed. Simulation results show that oxide plants located in northern Chile, served by the SING network, feature carbon footprint within 4.3 - 11.4 MWh I ton cathodic copper, as compared with 3.5 - 9.3 MWh I ton copper in plants served by SIC. The footprint was found to increase as ore wade and process yields decrease.

Jan 1, 2011

By James R. Hunter, Sandra K. Zacharias, Ursula M. Franklin

Archaeometallurgical remains can be a valuable source of information about past technological activities and, by inference, the societies that undertook them. Material traces of former metal-producing or metal-working centres can include raw materials, products, or metallurgical installations such as mines, furnaces or forges. Of these remains, the most common is slag, often left undisturbed since its original production. Physical and chemical analyses of archaeological slag and metal can often reveal the processes and materials involved in their formation. Mineral composition and softening temperature of a slag, for instance, can indicate the conditions of the metallurgical operation, such as temperature and atmosphere and, thus, help identify metallurgical processes which took place at a site(1). The present report illustrates the value of such analysis. Metal-working remains from Sainte-Marie among the Hurons, near Midland, Ontario, on the south side of Georgian Bay have been analyzed in order to determine the techniques and processes used by the 17th-century blacksmith who worked at the mission headquarters from 1642 to 1649. Samples were selected from a very large collection of blacksmith refuse which was excavated from the site by archaeologist Kenneth Kidd in 1941-42(2).

Jan 1, 1999

By A. V. Lyamin, J. P. Wang, A. J. Li, Z. Qian

"For general stability analysis of rock slopes, rock mass strength and rock mass disturbance are definitely should be considered. In addition, the impact of earthquakes must be taken into account. In fact, the rock mass strength is very difficult to be assessed which causes the difficulty of analysing rock slope stability. Therefore, an empirical failure criterion, the Hoek-Brown failure criterion, has been proposed. It is one of the most widely accepted approaches to estimate rock mass strength. The rock mass disturbance is important and was found having significant influence on evaluating rock slope stability, especially for rock slope with poor quality rock mass. In the Hoek-Brown failure criterion, the disturbance factor can represent the level of the rock mass disturbance which would provide a reasonable basis for estimating rock mass strength.This research will not only discuss the slope factor of safety, but also consider the influence of the seismic force on rock slope stability assessment using pseudo-static method. In practice, only horizontal seismic coefficient is used. Various magnitudes of the disturbance factor and recommended blasting damage zone thickness are also taken into account. The blasting damage zone thickness considered ranges from 0.5 to 2.5 times of slope height. The research results have potential to be extended and then sets of comprehensive stability charts can be provided for the rock slope stability evaluations. They will be convenient tools for practising engineers. In this study, finite element upper bound and lower bound limit analysis methods are employed. Their applicability has been investigated in some previous studies. The differences between upper bound and lower bound solutions are less than ±10% which would provide reasonable and acceptable range for rock slope stability safety factor estimation."

Jan 1, 2015

By B. Dubreuil, J. -M. Lalancette, D. Lemieux, C. Chouinard

The extraction of gold and silver has been examined via the use of mixed halogens: chlorine and bromine. The reaction was performed in a brine of sodium chloride with a small amount of sodium bromide at 40-50°C, in an atmosphere of chlorine, at atmospheric pressure. The process takes advantage of the very high reactivity of bromine towards gold, while the higher oxidation capacity of chlorine leads to gold chloride as end product with recycling of bromine. Fast reaction rates are observed along with gold recovery at the level of 95%. Chlorine-consuming common elements are removed prior to chlorination.

Jan 1, 2011

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the 'resistivity map of the subsoil' in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Alexander Smith

"The Silver Standard mine is 6 miles by road northwest of New Hazelton, B.C., a small town on the northern line of the Canadian National Railways some l 75 miles northeast of Prince Rupert. The deposits lie on the western slope of Glen Mountain (elevation 2,100 feet), with the main adit, mill, and campsite at 1,300 feet. The deposits were found in 1910, shortly after the area had been swept by forest fire and during a period of prospecting activity spurred by the construction of the railway. Crude ore only was shipped until 1918, when a 50-ton gravity mill was built which operated until 1922. Gross value of production of this period, at present metal prices, was about $1,000,000.In 1947 the present company was formed and a 50-ton flotation mill installed. Production from 1948 to 1955 has been in excess of $10,000,000, and net smelter returns about two-thirds of this amount. More than 60 per cent of the production and 80 per cent of the profit have come from one vein, No. 6. On the 1,300-foot level this vein had an ore section 375 feet long and 2.5 feet wide, averaging 0.18 ounces gold, 85 ounces silver, 10 per cent lead, and 16 per cent zinc.The mine workings follow a simple pattern. A series of parallel veins, striking northeast and dipping southeast, are numbered from 0 to 12, starting at the northwest. They lie within a zone trending south 70 degrees east, and the distance between Nos. 0 and 12 veins is about one mile. Recently several cross-veins, dipping northeast, have been found between Nos. 8 and 12. They are apparently of the same type as the others, though they may not have the same structural controls. They could be an important new source of ore.The mine has been developed principally by crosscut adits at the 1,500- and 1,300-foot levels and a 510-foot shaft with levels at I, 150, 1,000, ·and 850 feet. Drifts and crosscuts total 17,000 feet, chiefly on Nos. I, 4, 6, 7, and 8 veins. The drifts are stoped by shrinkage, top shrinkage rill, cut-and-fill with resuing, or open stope methods. The mill produces a lead-silver-gold-copper concentrate and a zinc concentrate, with indicated recovery of more than 96 per cent (4)."

Jan 1, 1949

By O. Espinoza Ortega, S. Song

A process scheme has been devised to improve the silver recovery and the grade of concentrates from the scavenger concentrate of a silver ore flotation circuit. Based on modal analysis studies it was found that silver sulfide minerals in the scavenger concentrate were associated as simple binary particles and finely disseminated in sulfide and non-sulfide gangues. Fine grinding of the concentrate improved the grade-recovery curve of silver to a very limited extent owing to heterocoagulation between liberated fine silver sulfides and coarse particles of gangue. This heterocoagulation phenomenon was prevented by grinding the concentrate in the presence of the dispersing reagent sodium hexametaphosphate. The silver grade-recovery curve was improved by practicing. before the conventional flotation step, a selective aggregation step for the fine silver sulfide particles using the non-polar oil kerosene, the sulthydryl collector Aerophine 3418 and conditioning the pulp under strong agitation conditions.

Jan 1, 2004

By A. Bascetin

The mining industry in Turkey has been developing in the last 10 years. Mine wastes and tailings have thus been increasing, depending on the rising production rates. There are many problems related to accidents that occur in tailings damps. In this study, the applicability of the surface paste disposal (SPD) method for a Pb-Zn mine in western Turkey was examined. Density was 3.084 and specific surface area was 0.899 m2/g. The mill tailings have very low plasticity and show characteristics of clays and silts in terms of the Unified Soil Classification System. The particle size distribution of the tailings was 39.2% particles finer than 20 µm. The results of this study showed that the physical and chemical properties of mill tailings make them suitable for SPD.

Aug 1, 2013

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998