Search Documents

By J. T. Kalala

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By R. Flood

"Oil has been discovered off Newfoundland in a number of locations on the Grand Banks, the most notable and exciting being in 1979 when Hibernia was discovered. This discovery has brought new challenges to the province as well as to all of Canada. During the seven years"" since its discovery, both industry and governments have attempted to define its parameters and to find the most efficient and economical way to develop the field.A number of studies have been completed during the interval and in 1985, Mobil Canada Ltd. and partners stated that they would prefer to develop the field by using a concrete Gravity-Based Structure (GBS). IntroductionHibernia is located in an environmental climate much more severe than that of any previously developed oil field. The wind and wave conditions are similar to those of the North Sea, but unlike the North Sea, any structure on the Grand Banks would have to contend with ice floes and icebergs. Decisions had to be made on whether fixed structures could be put in place that would withstand the pressures of the ice and the impact of an iceberg, or whether structures that could be removed when such impacts were imminent would be used.Early studies in 1981, determined that it was possible to build a concrete Gravity-Based Structure which could withstand the impact of the largest icebergs that are anticipated to float in that area of the banks.Additional studies increased the knowledge of icebergs: their patterns and size, and verified the original conclusions that Concrete Gravity-Based platforms would provide a practical solution."

Jan 1, 1988

By K. R. Brown, P. L. Krawchuk

In-situ recovery (ISR) is under increased investigation as a viable methodology for the extraction of minerals in ore bodies that may be uneconomic to mine by traditional methods or for resources situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash and uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. ISR allows for the extraction of metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in a process that produces very little to no waste rock or tailings. This paper aims to discuss the geological conditions that make ISR amenable to an ore body as well as the application of maturing technologies such as advanced directional drilling and the creation of artificial permeability that will help to access deep ore bodies and enhance or create favorable recovery conditions for ISR in the ore body. INTRODUCTION In-situ recovery (ISR), also referred to as in-situ leaching, is a potentially disruptive technology for the mining industry. ISR is under increased investigation as a viable methodology for the extraction of valuable minerals that may be uneconomic to mine by traditional methods or for deposits situated in locations where underground and surface mining operations are not feasible. Although the concept of ISR is relatively new with respect to hard rock applications, it is not a new technology; it has been used successfully in potash mining, uranium mining and also in heavy oil extraction for years where it has been proven to be both technically and commercially viable. Recently there has been increased interest in deploying ISR in hard rock applications due to a number of factors: the drive for environmental stewardship is stronger than ever, technological advances in drilling, blasting, and leaching are strengthening ISR economics, and a large inventory of ore bodies exists that are not feasible to mine or extract using conventional open pit or underground mining techniques. ISR allows for the extraction of valuable metals and minerals without the need to mine large amounts of ore that need to be processed at surface. The ore stays in-situ and only the valuable metals and minerals are produced to surface in solution via a recovery process that produces very little to no waste rock or tailings. Where the right conditions exist, the ISR process has a much smaller environmental footprint (Hiam-Galvez, 2018) and potentially much lower capital and operating costs than using conventional mining techniques.

Jan 1, 2019

By A. I. A. Salama, M. W. Mikhail

"The existing methods of block diagram manipulation and vanishing variable for flowsheet simplification used in coal and mineral processing circuit evaluation and optimization cannot be easily implemented on digital computer.The signal flowgraph technique is proposed to represent and simplify determination of the relationship between intermediate or end variable and the feed in the flowsheet. Typical and existing circuits are used to demonstrate the application of the proposed technique which can easily be implemented on digital computers.IntroductionRecently there has been much interest in the analysis and optimization of coal and mineral processing circuits to assist in the pre diction of coal and mineral processing plant performance. The block diagram and the vanishing variable were introduced and utilized in the analysis of plant flowsheet. Although the block diagram approach is useful, it requires manual manipulation of the circuit block diagram which may present difficulties in the situation of complex circuits. Moreover, it may not be easy to implement on a digital computer.In this paper, the signal flowgraph technique is proposed to represent the circuit flowsheet and to simplify the determination of relationships between intermediate or end variables (fractional mass) and the feed for any coal and for any mineral processing circuit comprising size and density separators. These relationships are utilized in the analysis and/or optimization of the circuit. The proposed technique is illustrated by considering typical and existing circuits."

Jan 1, 1987

By J. H. Gray

"IntroductionIn 1980, Fording Coal Limited started conceptual planning studies which led to major changes in the long-range mining plan at their Fording River Operations. These new plans have been completed and are now in operation.To assist personnel in a timely completion of this major revision to the long-range plan, existing in-house drill hole data base and scheduling systems were used and a computerized Mine Modelling and Planning System was purchased. With these tools, plan s were developed which led to completion of initial access to the peak of Eagle Mountain and the start of mining operations in March 1983. As mining area s open up and new geo logical data is obtained, detailed plan s are being extended and revised.With the geology and mine plan s on line, this work can now be done with less effort and plans ca n be adapted to provide flexibility in mining operations. Changes in market conditions can be accommodated by moving mining operations into different seams for different coal types. The computer systems are used to revise pit designs and schedules accordingly."

Jan 1, 1986

By Anthony P. Makuch

Dynatec Corporation is an integrated mining services company, providing mine development, operations management, engineering, drilling and metallurgical services to the North American mining industry. Dynatec was the contract operator of the Ken Snyder Mine in Midas, Nevada from start of production in January 1999 to September 2001. This paper summarizes Dynatec?s experience and approach to the use of longhole stoping methods for mining to widths of 1.3 to 2 metres in a steeply dipping narrow vein orebody.

Oct 1, 2001

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By E. Ozberk, N. Gibson, W. G. Davenport

"In the 1950s, Canada produced more than ninety-five percent of the non-communist world's nickel and achieved dominance in terms of production, technology and pricing policies.Over the past thirty years there have been dramatic changes in the nickel industry to the extent that Canadian production is now less than thirty per cent of the total.In this document we have presented statistics relevant to this transformation and reviewed the technology, particularly with regards to energy and environmental considerations.Under the new market conditions nickel producers are likely to face more difficult competition than they have encountered in the past.The economic scene and measured nickel reserves dictate that for the purpose of increasing production, new nickel smelters will not be built in Canada in the foreseeable future. However, in order to reduce sulphur dioxide emissions, Canadian nickel smelters will possibly go through some modifications or rebuilding.IntroductionThis paper presents a review of the Canadian nickel industry in relation to the world nickel industry. Major changes are described which have occurred in the characteristics of the nickel market over the last thirty years. The pre sent status of the nickel market with respect to Forecasting future trends is reviewed and attempts are made to predict what further changes will take place in the next two decades. Comparisons are made of the economics of producing nickel from sulphide ores and oxide ores and the advantages and disadvantages the Canadian nickel producers face.A brief critique of the existing and emerging nickel production technologies in Canada and the world is carried out and attempts are mad e to predict the changes which may take place in the foreseeable future."

Jan 1, 1983

By Lar Liljeblad

"As demands upon the earth's natural resources continue to grow, exploration companies, mining organizations and others face the problem of the need to tackle increasingly more difficult strata to open up new reserves. Innovations in materials technology and tool design have steadily improved this capability, but none perhaps so drastically as a recently introduced cemented carbide in which tool wear resistance and/or toughness can be tailored precisely to the user's drilling needs.Introduction Until about forty years ago, the bulk of rock-drilling operations had to be carried out with hardened steels. Short life between re-grinds was common especially in abrasive rock formations. Shortly after World War II, Sandvik, Sweden, pioneered the development of sintered (cemented) carbide-tipped steel tools as a means of improving drill tool life. The new material was a composite of tungsten carbide and cobalt, the latter acting as a 'cement' to bind the wear-resistant carbide grains together, and the composite, in turn, was brazed to the steel. The immediate effect was a 100-fold increase in the service life of the tool.Intractable ProblemsWhile the carbide-tipped tools served the mining and quarrying industries admirably there were, nonetheless, some seemingly intractable limitations. The greater the wear resistance of the material - the quality for which it is selected - the more brittle it is. Also, rocks vary widely in hardness and abrasiveness and no single tool, either in terms of material or shape, meets every need. Specifically, for fast penetration of non-abrasive rock, toughness must be combined with a relatively sharp tool prome. Highly abrasive rock, on the other hand, demands a substantially broad area of extremely wear-resistant material on the tool if long bit life is to be assured. Between these extremes there are innumerable variations in rock"

Jan 1, 1991

By Umbreen Agha, Stephan L. Chryssoulis, A. Margaritis

"The deportment of gold in samples of the biooxidation feed and product from the Harbour Lights mine in Western Australia was determined using optical microscopy and microbeam techniques such as Secondary Ion Mass Spectrometry (SIMS), Time-of-Flight Laser Ionization Mass Spectrometry (TOF-LIMS), and Electron Probe Microanalysis (EPMA). The main objective was to determine the mechanisms by which acidophilic bacteria (Thiobacillus ferrooxidans) liberate refractory gold which is locked in a sulphide minerals host as visible gold inclusions (> 0.1 µm) and as submicroscopic or 'invisible' gold.Using the integrated mineralogical approach approximately 99% and 100% of the assayed gold in the biooxidation feed and biooxidation product was accounted for. The results were compared to and verified by chemical assays.The gold deportment study indicates that during biooxidation, locked visible and 'invisible' gold is rendered cyanidable by the direct action of Thiobacillus ferrooxidans as well as indirect chemical leaching. Visible gold which is enclosed in sulphide minerals is liberated or partially exposed and is therefore rendered cyanidable as the host mineral is oxidized and dissolved. 'Invisible' gold either coalesces on the surface of the host sulphide mineral as the particle is dissolved or is released into the liquid phase and immediately adsorbs onto the surface of other ore particles with a net negative charge.The shakeflask suspension indicates that direct bacterial oxidation pits and channels correspond to zones of 'invisible' gold and arsenic (in pyrite) enrichment in the host sulphide mineral."

Jan 1, 1996

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

"In the first half of 1990, Cambior earned $1104 million, or $0.37 per share, on revenues of$66.4 million. The company's strong cash position, attained late in 1989 and in the beginning of1990 through the exercise of warrants, put working capital at $83.8 million as of June 30, 1990. Long-term debt was reduced by over $10 million during the weak gold market, leaving the company with a debt to equity ratio of only 0.03. Production for the six first months of 1990 was 107 720 oz. Au, an increaseof24% over the corresponding period in 1989.Financial Profile/Results and Corporate Financial StrategiesTotal revenue for the 1989 fiscal year was $116,883,000 compared to $109,848,000 for 1988. The 1989 results achieved despite a lower average gold price, resulted from a higher level of commercial gold production and a 115% increase in investment income over 1988. Investment income rose to $3,568,000 in 1989 due to higher levels of cash assets.Cambior's mine operating costs increased 19% to $68,561,000 in 1989 from $57,472,000 in 1988. This increase resulted from rising operating costs at the Doyon Mine ($250/oz to $274/oz) due to the shift from open pit to underground operations, as well as from the start -up of three new mines with relatively higher costs. These costs have reached a stable level that should be maintained for the next few years.In 1989, net exploration expenses were $6,838,000, down 31070 from 1988, partially due to the Canadian tax reforms introduced since 1987. Depreciation and depletion grew by $1,432,000 in 1989, reflecting a higher volume of commercial production from the Pierre Beauchemin, Lucien C. Beliveau and Chimo mines.Net earnings for 1989 amounted to $17,661,000 or $0.73 per share compared to $17,438,000 or $0.74 per share in 1988.Cambior has an exceptionally liquid and strong balance sheet. As at December 31, 1989, net working capital stood at $85.6 million, with a total assets base of $338.6 million. With a long-term debt (including gold loans) of $21.5 million and shareholders' equity of $277.2 million, Cambior has a debt to equity ratio of 8%. All but about $100,000 of long-term debt is in the form of gold loans.The total market value for Cambior's stock as at September 10, 1990, stands at $420million, based on recent stock market prices. Cambior's stock and warrants are traded on the Montreal and Toronto Stock Exchange."

Jan 1, 1990

By Alan G. Galley

"Advances in our knowledge of the petrochemical attributes of deposit environments and of the character and extent of hydrothermal systems associated with certain deposit types has resulted in increased application of lithogeochemistry to exploration programs. Lithogeochemistry can be used to vector an exploration program toward an area of high potential through the use of a series of collapsing scales of analysis from a tectonic subprovince down to a particular stratigraphic segment. In the case of volcanogenic massive sulphide (VMS) deposits this involves the recognition ofsuitable volcanic domains, and the identification of subvolcanic intrusions and cogenetic felsic extrusive complexes. The recognition of chemical vectors within regional-scale alteration zones and associated chemical sedimentary rocks allows the geologist to identify the stratigraphic units with the most potential for hosting a base metal deposit.An integrated lithogeochemical program requires the judicious use of major, trace and rare-earth element and isotopic analysis. Standard discriminant plots may be employed to identify suitable tectonic and lithologic environments. Analysis of the chemical and mineralogical variations in broad-scale, semi-comfortable alteration zones provides a useful set of vectors to VMS mineralization. These may include contouring raw data, element ratios on XY plots, normalizing data against known rock values, or calculating mass changes in alteration zones."

Jan 1, 1995

Training by Inclusiveness ?Background ?Video ?Results ?Partners ?How SEM works ?Future of SEM Background: Inclusivity partners ?Northwest Community College ?Smithers Exploration Group ?With support from the Province of BC ?Federal government ?And First Nations across the northwest

May 1, 2010

By Pierre Choquet

"The whole work carried out both in situ and in laboratory by a research group of the West German collieries is presented. This work has led to a design method of steel arch supports for gate roadways that gives full satisfaction in this particular coalfield. The method accounts for mining depth, the mining system (advancing or retreating), thickness of the coal seam and other parameters.Full statistics are then given on gate roadway supports of the ECCS (European Community for Coal and Steel) coalfields. They were collected by the author in order to show that the West German method can be applied to other coalfields as the long wall systems which are generally being used are very similar. Design calculations are conducted for each coalfield's case. They show that the method would have been able to predict in most cases the support actually used.Utilization of the design method is recommended to the Cape Breton Development Corporation 's mine operators because mining conditions, even though different from European ones, present a number of similarities which make it possible to apply the design method to their particular case.This procedure might be profitable in mines facing support problems in their levels and for any planning of future projects"

Jan 1, 1986

By Hung-wei Liu, Kevin Plucknett

Early attempts to manufacture titanium aluminides using blended elemental powders, through powder metallurgical processes, have been obstructed due to serious swelling during sintering. Although the use of pre-alloyed powder can avoid this undesired expansion problem, there are limited commercial powder sources available. Therefore, in the present research, fundamental studies on the synthesis of dual-phase (? plus a2) Ti48Al intermetallic materials is undertaken, in particular assessing powder manufacture. In order to produce pre-alloyed powders, highly porous Ti48Al pieces are initially sintered from elemental Ti and Al powder blends, and subsequently pulverised into powders. The powder size is then further reduced by use of either dry or wet milling processes (i.e. shatterbox grinding, attrition, or ball milling). Among these methods, shatterbox grinding has shown the highest efficiency, with a slight mechanical alloying effect observed. The manufactured powder morphologies and phases, as well the sintered material, will be discussed.

Jan 1, 2015

By Simon B. Blancher, Malo Rousseau, Renato Contessotto, Thomas Wallmach

The Manganese division of the ERAMET group extracts manganese ore in Gabon and produces manganese alloys for the steel industry. ERAMET has an economic interest to maximize the ore throughput without reducing the lifetime of its manganese mines. This can be achieved by means of research and development leading to innovative ore beneficiation processes. For this purpose, the ERAMET research center has designed and constructed a new pilot plant for ore beneficiation by physical separation processes. This pilot facility was erected within an infrastructural and synergetic framework, including competencies in hydrometallurgy, pyrometallurgy, numerical modelling, analyses and mineral characterization that provide ideal research conditions. After laboratory scale tests, a pilot operation of beneficiation of low grade Mn ore (around 35% Mn) was carried out by jigging of the 1-10 mm fraction. This gravity separation process exploits density differences between the various Mn-bearing minerals such as pyrolusite and lithiophorite as well as gangue minerals such as silicates and iron-hydroxides. Enrichment leads to the production of a marketable product associated with a high mass recovery (53% for the jigging step). However, 20% of pyrolusite and 30% of lithiophorite are lost in the waste. Mineral characterization has shown microtextural complexities, but grinding the ore to approach the liberation mesh was not an option due to commercially defined constraints given by the ferro-alloy industry. Recovery of the Mn-bearing minerals or adjustments of the feed grain size (6.3-10 mm) are two potential areas of process improvements identified by means of Qemscan® mineral characterization. This paper details the process tested on a pilot scale (0.5 t/h), which has led to a significant increase in the beneficiation of a low grade Mn ore.

Jan 1, 2016

By Kamran Esmaieli

Open Pit Mining Through Underground Voids: Challenges Main Challenges/Hazards: Unexpected collapse of the pit floor and/or pit walls; The loss of equipment and/or people into underground voids; Loss of explosives from blast holes that broken through into the underground voids. How to address these challenges? An important step that must be integrated into mine planning and design is the accurate detection and delineation of underground voids. (i.e. probe drilling, Geophysical techniques, laser scanning,?); Leaving a pillar of adequate thickness between the working bench and the underground voids; Backfilling the underground voids from surface using vertical or inclined raises; Monitoring the working locations (pit floor and pit slopes) to detect movements.

May 1, 2013

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By R. G. Bradbury

The paper uses two hypothetical, but typical, situations to show that hydraulic rock drilling equipment has very significant economic advantages over pneumatic equipment both in drifting applications (even in the situation where advantage is not taken of the high productive capacity of the hydraulic drill) and production drilling applications. Other factors, including the non-economic advantages and the disadvantages of hydraulic drilling, are discussed. The paper concludes with a brief analysis of why the Canadian mining industry has been slow to take advantage of this apparent broadly advantageous advance in rock drilling technology.

Jan 1, 1979