Search Documents

By K. H. Poulsen, C. J. . Hodgson

Synvolcanic, layered gabbro-anorthosite sills at Rainy Lake, Northwestern Ontario, reflect a combination of igneous processes including fractional crystallization, wall rock assimilation and possibly liquid immiscibility. Chalcopyrite-pyrrhotite mineralization at the base of the Grassy Portage intrusion accumulated by crystallization of a sulphide liquid during cooling. Upward enrichment of Fe and Ti in this intrusion and also in the Bad Vermilion Lake anorthosite complex culminated with the crystallization of lenses of disseminated to massive magnetite+ apatite+ ilmenite+ rutile. Regional low to medium grade metamorphism and accompanying deformation resulted in recrystallization and local remobilization of ore minerals.

Jan 1, 1984

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By C. Liu

Zeta potentials and settling rates of an oil sands tailings sample taken from Syncrude Canada Ltd's Aurora Stacker Pilot Operation were studied. Two clay minerals, kaolinite and illite, were also studied since these are the major constituent minerals in the fine oil sands tailings. Process water, decanted water as well as distilled water were used. It was observed that the zeta potentials of the tailings solids showed maximum negative values in process water at pH 8-10, which coincides with the pH of commercial hot water bitumen extraction process. The settling rates of the tailings sample were very low, at 0.008 m/hr in decanted water and 0.04 m/hr in process water. The rates were increased to 1.0 m/hr in decanted water and 0.13 m/hr in process water at an addition of 50 g/t Ciba AF1235. Although the settling rate was higher the supernatant was cloudier in decanted water than in process water. Further increase in the dosages of Ciba AF1235 did not increase the settling rates in decanted water but gradually increased it in process water, reaching 0.46 m/hr at 100 g/t. The results indicated that lower concentrations of Ca2+ and Mg2 (in decanted water) benefited settling rates but did not benefit supernatant clarity. Test results also indicated that Ciba AF1235 caused selective flocculation of the tailings sample, since the top sediments had higher illite and lower quartz contents than the bottom sediments.

Jan 1, 2006

By Carl Pelletier

The Sigma-Lamaque Complex is considered a lode-gold deposit characterized by narrow vein structures, which have been mined historically by underground methods. In addition to the narrow vertical structures, mining also took place on horizontal veins, ?North Dipper? veins and dykes mineralized with sub-horizontal veins and stringers. Over the 60 + years of production, mining took place to a depth of 1.8 km. The upper portion of the deposit was considered all but exhausted, when viewed from an underground mining perspective. The year 1998 is considered a turning point for the Complex when a small open pit was mined at Sigma. The resource evaluation methods used underground were applied to surface mining, which allowed small pits to be mined. The resource evaluation method considered only the narrow vertical structures and was not well adapted to open pit mining. As a consequence, resources were consistently under evaluated. It became clear that a new geological approach was necessary to more accurately define resources (i.e., what was being mined). In order to integrate all characteristics (geometry, mechanics and chronology) of this complex lode-gold deposit, a new geological model was proposed. Due to this new approach, dating to February 2000 and updated in December 2000, the reserves evaluated in the first 180 meters now stand at 15 million tonnes @ 2.61 g/t Au (1,265,350 oz). Those reserves cover an east-west corridor extending 1,500 m by 750 m.

May 1, 2001

By B. Surender Mohan

Mother Earth being a treasure of minerals, it is prime duty of the mankind to preserve this natural source to ensure steady growth of the nation. Utmost care is to be taken to see that these natural resources are explored and exploited scientifically in a sustained manner to ensure that the resource base improves and last longer. In this backdrop, the topic of ?Lignite - its resource and technology options to exploit deep seated deposits? is an apt subject to be deliberated upon in the present context, where the shallow deposits may slowly get dwindled. I shall deliberate upon the resource base of lignite, production profiles of the last five decades, consumption pattern, demand / supply projections, future available technology options to exploit the deep seated deposits, growth trends of the sector etc. in my paper. With the available resource base and future technology options, I can confidentially make a statement that ?lignite will remain as cocontributor along with coal to India?s energy generation and may well maintain its same status in the 21st century too, as it has been in the later part of the twentieth century?.

Aug 1, 2013

By D. Runnels, Daniel Roy, Ricardo Esteban, J. Torrealba-Vargas

"An intuitive way to reduce power consumption in grinding operations is to feed the grinding circuit with finer feed by enhancing blasting and fragmentation control. The optimization of blasting with the objective of minimizing power consumption in grinding is not new.The study was based on a Canadian mine that processes a very hard ore. BBA conducted blasting/fragmentation and grinding circuit surveys in 2014. The results of the exercise were used to develop a base case model to simulate the effect of blasting in the operation on the grinding circuit. Tools for fragmentation simulations, particle size measurement and crushing/grinding simulations were used with the objective of reducing the OPEX costs including power consumption.The paper describes the steps involved in the model optimization as well as an economical evaluation of the OPEX savings.INTRODUCTIONIn 2014 BBA was retained by one of its clients to conduct a crushing and grinding survey. The objective of the survey was to update the grinding circuit model with production data and also to develop a tool to investigate opportunities for process improvement.A second phase of the study involved the development of drilling and blasting and crushing models. The models were used to diagnose the operations and to investigate opportunities for process improvement.The objective of the present study is to describe the approach and to identify potential improvements to overall mine site operating costs by better integrating mining and milling operating costs with blasting and grinding models."

Jan 1, 2016

By G. Bartolacci

In a COREM-McGill collaborative research and development project, gas dispersion parameters and froth properties were manipulated in a copper flotation plant to study interactions between the collection and the cleaning zones. In this paper, specific work on developing some relationships between operating conditions and froth stability in several different types of flotation cells is reported. Froth stability, measured by image analysis, was related to the following process conditions for specific flotation machines in an industrial case study: Gas flow rate, collector dosage, pH, frother type and dosage. Across the range examined, froth stability was improved through an increase in gas flow rate and/or frother dosage. Metallurgical results (grade and recovery) showed that both gold and copper were dependent on froth stability. Results indicated that flotation conditions could be optimized by monitoring froth stability.

Jan 1, 2007

By A. Lam

The use of a liquid fed direct methanol fuel cell (DMFC) as a power source for micro and small portable applications is attractive due to its system simplicity, low temperature, etc. The aqueous methanol is directly oxidized and does not require additional fuel processing steps as in reformate based PEM fuel cells. In addition, the use of a liquid fuel is advantageous with respect to humidification, stack cooling and system energy density. The DMFC however, has technological issues that must be addressed before it can be widely adopted, particularly in larger applications such as small utility and transportation. At present, the crossover of methanol from the anode to the cathode is a major limitation on DMFC performance and fuel utilization efficiency. In this paper we discuss the influence of fuel modification on the control of crossover. This involves the use of different fuel additives and concentrations to minimize crossover. This appears to be the first reported case of the use of fuel modification (additives) to reduce methanol crossover. The rate of methanol permeation under passive conditions is discussed with respect to the different conditions.

Jan 1, 2005

By Mengmeng Gai

This paper introduces a model-based automatic object recognition and registration framework to assist heavy equipment operators in rapidly perceiving 3D working environment at dynamic construction sites. A video camera and a laser scanner were utilized in this study to rapidly recognize and register dynamic target objects in a 3D space by dynamically separating target object?s point cloud data from a background scene for a quick computing process. A smart scan data updating method has been developed which only updates the dynamic target object?s point cloud data while keeping the previously scanned static work environments. Extracted target areas containing 3D point clouds were orthographically projected into a series of 2D planes with a rotation center located in the target?s vertical-middle line. Prepared 2D templates were compared to these 2D planes by extracting SURF features. Point cloud bundles of the target were recognized, and followed by the prepared CAD model?s registration to the templates. The field experimental results show that the proposed rapid workspace modeling method can significantly improve heavy construction equipment operations and automated equipment control by rapidly modeling dynamic target objects in a 3D view.

Aug 1, 2013

By M. B. Greyver

The results of laboratory tests on iron precipitation from non-decopperized nickel anolyte are discussed. The parameters (pH, oxygen consumption and stirring speed) for iron precipitation from the anolyte, using the oxygen in the air, were determined. In the experiments conducted under optimized conditions, the residual concentration of iron in the anolyte after precipitation was 0.7-2.7 mg/L, and the copper and nickel losses to the solid phase were 0.05-0.07% and 0.05-0.16%, respectively. The filtration ability of the iron slurry obtained was 2 to 5 times higher as compared to that after chlorine oxidation and oxyhydrolysis. The leaching of the non-ferrous metals from the iron cake made using the separate nickel anolyte purification process was possible by dissolution in sulphuric acid. It was established that after cobalt precipitation from the copper- and iron-depleted anolyte, the precipitates obtained had lower ratios of Fe:Co and Ni:Co.

Jan 1, 2006

1.Assessment of methane content in coal. Given a naturally low methane content in 11 Coal Seam and the fact that the areas of the 11 Seam adjacent to the tunnelway were degassing for a very, very long time due to previous development and mining, it is conservatively estimated that the remaining in -situ methane is less than 0.5m3/tonne. 2. Continuous miner cutting rate based on the past practice. The best loading rate recorded at the past operations of Smoky River Coal was 45 seconds for a 8 tonnes shuttle car. Using these records, the maximum peak loading rate potential at the face is calculated at 0.178 tonnes per one second or 10.67 tonnes per one minute. 3. Methane release at the face. ?The actual face methane liberation, conservatively assumed at 40% of the total in situ content: 0.20 m3/tonne ?The peak cutting rate: 0.178 t/sec ?The maximum (peak) face methane release: 0.20*0.178 = 0.036 m3/sec

May 1, 2003

By Kuwauchi. Y., M. Barati

Recycling of dust using a rotary hearth furnace (RHF) has gained considerable attention in the past two decades for the sustainable production of steel with less environmental impact. In order to further promote the recycling of electric arc furnace dust and carbonaceous wastes using the RHF process, a mathematical model was developed to predict the reaction behaviour of dust-reductant composites. The reduction kinetics of zinc and iron oxides as well as the volatilization behaviour of volatile matter in the reluctant were considered. The modeling approach and some preliminary results are presented in this article.

Jan 1, 2011

By K. Ebrahimi-Nasrabadi

The dependence between the extent of conversion of cryptocrystalline magnesite to caustic magnesia was studied experimentally in the temperature range of 400?1200 °C and for calcination times up to 8 h. A TGA?DTA analysis showed that decomposition begins at temperatures as low as 340 °C and is completed at 600 °C. Measurements of specific surface area (SSA), iodine adsorption number (IN), crystallite size, and loss on ignition were carried out to characterize the product quality. It was found that while all the parameters are dependent on the extent of calcination, densification of the product caused by grain coarsening affects their final values. As a consequence, SSA and IN went through a maximum with time. The study showed that high quality caustic calcined magnesia can be produced in a narrow range of temperature (600?650 °C) and time (1?4 h). Medium quality caustic calcined magnesia can be made within a wider range of parameters.

Aug 1, 2013

By N. Wachgama, J. P. T. Kapusta, R. U. Pagador

The Thai Copper Industries smelter (Thai Copper) is located some 200 km southeast of Bangkok near the MapTaPhut deep sea port in one of the industrial centres of Thailand. Although construction of the complex started in the mid 1990s, the smelter, acid plant and refinery were completed in 2004. Thai Copper is a state-of-the-art copper smelter processing imported concentrates with a total yearly capacity of 165,000 tonnes of cathodes. It employs the El Teniente Technology where concentrates are blended and smelted continuously in a primary smelting reactor to produce high grade matte or white metal. The white metal is converted in batches to blister copper in Hoboken siphon converters equipped with Air Liquide Shrouded Injector (ALS I) Technology for sonic injection of oxygen enriched air. Final refining is carried out in two anode furnaces prior to anode casting and electrorefining. Thai Copper and Air Liquide Canada executed a technical assistance agreement in late 2005. Pre-commissioning of the shrouded injectors took place in July and November 2006 while hot commissioning occurred in December 2006. This paper presents the major technical aspects of the joint commissioning, including the establishment of operating practices specific to shrouded injection converting. Preliminary results of this first commercial implementation of ALSI Technology in copper converting are also provided.

Jan 1, 2007

Keeping the sediment on the mine site and out of the water course is essential from the regulatory, environmental and sustainability perspectives. Regulation of this aspect of mining is embedded in environmental legislation and government receiving water quality standards, and government control has apparently been considered to be the most appropriate method to define mine site discharge standards and the environmental implications of sediment in downstream watercourses. A literature search for guidelines for the site specific design and operation of sediment ponds treating mine site runoff to remove total suspended solids, turbidity and flocculant-induced toxicity, revealed little information on the mining industry?s and government?s roles in defining the ?how to achieve? related to sediment pond design. Is there a need or reason for an industry-driven leadership to clearly define the ?how to? keep the sediment on the mine site and out of the water course? Currently, this issue is addressed in Canada by a federal mining regulation for metal mines which specifies discharge quality for sediment. This paper focuses on the method used in British Columbia, Canada, to regulate and provide a scientific methodology to control the discharge of sediment from mine sites. Management plans relative to this topic are discussed and are considered to have value from the exploration, construction, operation and the onset of closure phases. In addition, the balance and linkage between the erosion control management plan and the sediment pond management plan are discussed in terms of how they may be designed to complement each other to lower the risk of exceeding discharge and receiving water quality standards. If there were an industry-driven standard, or guidance document relative to addressing sediment release, it would benefit mining companies by eliminating the repetitive analysis of this topic for each new mine, mine expansion, and mine modification; also, government may often replace certain aspects of permitting with a regulation, if there is a government/industry established standard defining Best Achievable Technology (e.g. the Canadian Metal Mining Effluent Regulations).

Aug 1, 2013

By F. Barriga-Ordonez, J. A. Finch, L. Calzado, S. R. (Ram) Rao

Sludge, formed by lime treatment of acidic drainage and stored in tailing ponds of the Sudbury region, contains 5-7% Ni, mostly in a mix of hydroxides with Fe (~ 10%), Mg (~ 10%) and Cu (-0.5%), and Ca (-3.5%) as sulphate. Investigations were conducted to recover nickel by a 2-stage process. In the first stage, the sludge was leached with sulphuric acid at pH 3.2. About 90% of the nickel was extracted, producing a solution, which contained mainly nickel (2 g/L) and magnesium (3.7 g/L). In the second stage, nickel was separated by treating with ozone which recovered 99% of the nickel in the Ni(III) oxidation state as -85% pure nickel oxide-hydroxide (NiOOH) precipitate. The oxide settled and filtered readily. A potential use of the product in battery making is suggested. The leach residue contained 0.5% Ni making it less toxic for disposal. Some physical properties of nickel oxy-hydroxide and process parameters including ozone consumption will be discussed.

Jan 1, 2005

By Minghao Hu, Hongbo Zhao, Jun Wang, Wenqing Qin, Rui Liao, Central South University

"In the present work, X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS) analysis and electrochemical analysis were carried out to investigate the intermediate species and electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms. For bioleaching of chalcopyrite by the sulfur oxidizing microorganism Acidithiobacillus caldus, the redox potential was always lower than the appropriate value and chalcopyrite was mainly directly oxidized to polysulfide (Sn 2-), thus resulting in low copper extraction. As for bioleaching of chalcopyrite by the iron oxidizing microorganism Leptospirillum ferriphilum, chalcopyrite was mainly directly oxidized to polysulfide at the initial stage where redox potential was lower than the appropriate value and resulted in low dissolution rate. At the middle stage where redox potential was appropriate (about 350–480 mV vs. Ag/AgCl), chalcopyrite was mainly transformed to intermediate species of Cu2S rather than polysulfide, thus resulting in high dissolution rate. At the later stage where redox potential was higher than the appropriate value, chalcopyrite was mainly directly oxidized to polysulfide which caused the later passivation of chalcopyrite. Finally, a model of electrochemical dissolution process of chalcopyrite in the presence of sulfur and iron oxidizing microorganisms was provided.INTRODUCTIONBiohydrometallurgy is considered as one promising mineral processing technique in processing low grade ores due to the advantages of simplicity, low cost and eco-friendly. Chalcopyrite (CuFeS2) is the most abundant copper-bearing resource, accounting for appropriately 70% of the known reserves in the world, while is recalcitrant to bio-hydrometallurgy mainly due to the coated passivation layer (Klauber, 2008; Li, Kawashima, Li, Chandra, & Gerson, 2013). However, the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching are still uncertain. The microorganisms assisting chalcopyrite dissolution can be mainly classified into three types, including mesophilic microorganisms (e.g., Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans and Leptospirillum ferrooxidans), moderately thermophilic microorganisms (e.g., Acidithiobacillus caldus, Sulfobacillus thermosulfidooxidans and Leptospirillum ferriphilum), and extremely thermophilic microorganisms (e.g., Metallosphaera sedula, Sulfolobus sp., Acidianus sp., and Sulfurcoccus mirabilis). Moderately thermophilic microorganisms have a better prospect in the future industrial application of chalcopyrite bio-hydrometallurgy (Olson, Brierley, & Brierley, 2003; Rohwerder, Gehrke, Kinzler, & Sand, 2003). Hence, investigating the detailed dissolution and passivation mechanisms of chalcopyrite bioleaching by moderately thermophilic microorganisms is of important significance, which will provide essential information for promoting chalcopyrite bioleaching by moderately thermophilic microorganisms in laboratory or industrial plant."

Jan 1, 2016

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By M. Staite

This paper analyzed the feasibility of converting a 5kW natural gas SOFC power generator system designed to operate on natural gas to be fuelled by methanol. The analysis included laboratory methanol fuel processing experimentation, methanol reformate SOFC cell testing, and SOFC system mass and energy balance modelling. Methanol fuel processing experimentation indicated that theoretical reformate compositions can be achieved for high temperature (600-900°C) methanol steam reforming. A 6% open circuit voltage decrease and a 10% peak power current density decrease between cell operation on humidified hydrogen and methanol reformate was observed. SOFC system mass and energy balance modelling indicated that a natural gas SOFC system can be converted to operate on methanol fuel with minimal (1%) efficiency impacts, however the systems' thermal integration can be impacted.

Jan 1, 2005

By K. D. Peaslee

Slag splashing is an important development that has dramatically improved BOF vessel campaign life and reduced operating costs. This paper highlights research from physical modeling work using a 1/8-scale room temperature model BOF and slag characterization studies from several plants in North America and China. In the model studies, gas flow rate during blow and viscosity of the liquid were found to be two of the most important factors to changing the overall rate of liquid splashed onto the vessel sidewalls. When the flow rate was increased or viscosity decreased, the lower regions of the walls were splashed at a much greater rate. It was also shown that by changing the lance height, more liquid was deposited in the upper regions of the vessel at the expense of lower regions. Reducing the number of nozzles was found to be the most effective method of selectively coating a particular vertical section of the wall. Studies of BOF's using slag splashing in North America and China showed a difference in the melting characteristics of the final slag. Generally, slag splashing is successful when the melting point of the slag is 220-270°C below the tap temperature to maintain a balance between fluidity and refractoriness.

Jan 1, 2004