Search Documents

By A. Hussain

PAPER NOT SUBMITTED FOR PUBLICATION

Jan 1, 1987

By A. V. Tarasov

There are still a number of copper smelters in the world using the roasting and smelting process flow diagram for treating sulphide raw materials. The technical, economic and environmental performance indicators of such operations are inferior to the respective indicators of advanced processes. First of all with respect to copper and sulphur recovery: 95% and 75% as compared with 98% and over 90%, respectively. Based on the studies of the single-stage smelting process to produce white metal and blister copper conducted during recent years an analysis of the feasibility of roastingsmelting technology improvement was carried out in the Gintsvetmet Institute to substantially increase the copper and sulphur recoveries. On the basis of this analysis, it was proposed to modernize the technology and equipment within the framework of the existing process flow-sheet. The proposed modernization implies an increase in the roasting temperature; higher desulphurization degree in the process of roasting; a number of modifications in the roaster design depending on the particular conditions of a given operation; addition of lime flux to the feed charge to roasting; and transition to combined calcium-silicate smelting slags. The metallurgical and energy computations made have indicated that the proposed modifications of the technology will improve the copper and sulphur recovery up to 98% and 90%, respectively. The required capital investments have been estimated using as an example a particular copper smelter, the payback period determined taking into consideration additional output, fuel saving and a reduction in fines for sulphur emissions. For comparison, the capital cost of a smelter modernization is given for change-over to basically new autogenous Ausmelt, Outokumpu and V anyukov smelting technologies.

Jan 1, 2007

By S. R. McCutcheon, D. R. Lentz, W. S. Downey

"Abstract - The Little Falls member of the Nepisiguit Falls Formation is situated in the northern part of the Brunswick Belt of the Bathurst Mining Camp and has been interpreted as the distal equivalent of proximal tuffaceous rocks that host the stratiform Brunswick No. 12 and No. 6 Pb-Zn massive sulfide deposits. It comprises fine-grained, greenish-gray tuffaceous sandstone in the lower part, and coarse-grained, crystal-rich tuffaceous sandstone in the upper part. Petrographic evidence suggests that these rocks have a turbiditic origin. The Little Falls member is underlain by the Vallée Lourdes member, mainly composed of relatively shallow-water calcareous rocks, and is conformably overlain by Mn-rich sedimentary rocks, mainly red argillites that host the Tetagouche Falls Mn-(Fe) deposit. All these rocks are considered to belong to the Nepisiguit Falls Formation, part of the Ordovician Tetagouche Group. Whole-rock geochemical data from the fine-grained tuffaceous sandstone and coarse-grained tuffaceous sandstone indicate that the two units of the Little Falls member are distinct. Zr and TiO2 contents, and total rare earth element (REE) values are higher in the coarse-grained unit (average Zr/TiO2 = 0.040, average SREE = 247 ppm, n = 6) than in the fine-grained unit (average Zr/TiO2 = 0.048, average SREE = 158 ppm, n = 17), which can be attributed to the variation in crystal content between the two units. Both units are HREE-enriched and have elevated La/Yb relative to the typical Nepisiguit Falls Formation. Overall, the geochemical data combined with evidence from the bounding units suggest that the Little Falls member was deposited in relatively shallow water, possibly in a near-arc environment. The relationship of volcanic facies within the Nepisiguit Falls Formation and the geochemistry of these facies indicate strongly that fine grained, reworked tuffaceous rocks, regardless of whether they are the distal equivalents of proximal tuffaceous rocks, are not associated with the major ore-bearing horizons of the Bathurst Mining Camp. Sommaire - Le Membre de Little Falls de la Formation de Nepisiguit Falls se retrouve dans la partie nord de la Ceinture Brunswick du Camp Minier de Bathurst ou elle a été interprétée comme l’équivalent distal des roches tuffacées proximales hôtes des gisements de sulfures massifs de Pb-Zn stratiformes Brunswick No.12 et No.6. Il consiste en grès tuffacé à grains fins gris verdâtre dans sa partie inférieure et en grès tuffacé à grains grossiers riche en cristaux dans sa partie supérieure. Les données pétrographiques suggèrent que ces roches ont été déposées par des courants de turbidité. Le Membre de Little Falls repose sur le Membre de Vallée Lourdes, lequel consiste principalement en roches calcareuses déposées en eau relativement peu profonde; il est de plus recouvert en concordance par des roches sédimentaires manganifères, lesquelles consistent principalement en argilites rouges hôtes du gisement de Mn-(Fe) de Tetagouche Falls. Toutes ces roches appartiennent à la Formation de Nepisiguit Falls, laquelle fait partie du Groupe de Tetagouche, d’âge Ordovicien. Les données lithogéochimiques des grès tuffacés à grains fins et à grains grossiers indiquent que ces deux unités du Membre de Little Falls sont distinctes. Les teneurs en Zr et en TiO2, ainsi que la teneur totale en Éléments des Terres Rares (ÉTR) sont plus élevées dans l’unité à grains grossiers (Zr/TiO2 moyen = 0.040, SREE moyen = 247 ppm, n = 6) que dans l’unité à grains fins (Zr/TiO2 moyen = 0.048, SREE moyen = 158 ppm, n = 17), ce qui pourrait s’expliquer par la variation de la quantité de cristaux dans chacune de ces deux unités. Chacune de ces deux unités présente un enrichissement en ÉTRL ainsi qu’un rapport La/Yb relativement plus grand que ce qui est typiquement observé dans la Formation de Nepisiguit Falls. Les données géochimiques considérées conjointement à l’information provenant des unités adjacentes suggèrent que le Me"

Jan 1, 2006

By A. Warczokand

The cleaning of copper smelting slag requires magnetite and cuprous oxide reduction. The slag reduction with coke, injected coal powder or bunker oil is strongly endothermic and requires heat generation by fuel combustion or the use of electric energy. The reduction of fayalitic slag with calcium carbide is slightly exothermic and the formed calcium silicate modifies the slag. Thus, the additional energy is required only for covering furnace heat losses. Results of crucible scale tests showed the rate of slag reduction approximately five times higher in comparison of the slag reduction with coke under the same conditions. It seems that the effect of exothermic reaction and slag modification with CaO at the reaction interface results in very high rate of slag reduction. Industrial scale tests carried out in the Anglo-American Chagres Smelter demonstrated the possibilities of effective reduction and cleaning of the slags from a flash smelter and Peirce-Smith converters in a Teniente Slag Cleaning Furnace. The slag reduction was carried out without any reductant or stirring gas injection, simply by calcium carbide charging through a furnace mouth, and was very fast.

Jan 1, 2007

By S. Kashani-Nejad

The formation of oxides during the dehydration of MgC12,6H20, Bischofite, was studied by heating the bischofite over a range of time and temperatures in ambient atmosphere. Using a methanol-leaching technique developed by authors, the oxides that formed were isolated, identified and assayed. Three distinct regions of oxide stability were identified. The oxide produced at dehydration temperatures less than 300 °C was Mg2(OH)3C1,2H2O; at 300 °C, mixtures of MgOHC1 and Mg2(OH)3C1.2H2O were formed and at 400 °C, MgOHC1 was the only oxide produced. The presence of MgO observed in the products of the dehydration of bischofite at temperatures above 400 °C was due to the thermal decomposition of the MgOHC1 that was formed while the sample was heating to over 400 °C.

Jan 1, 2006

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

Batch grinding tests conducted on a gold ore indicated that gold is not randomly distributed within the size fractions of the ground ore. Since gold leaching performances were found to be dependent of the size of the gold carrying particles an integrated gold ore grinding-leaching simulator should incorporate a method to predict the gold size distribution of a ground ore. The paper describes the results obtained from batch grinding tests showing the non random distribution of gold within the size intervals of a ground ore and the initial developments of a grinding model to predict the gold size distribution in a batch grinding product.

Jan 1, 2011

By V. K. Karra

A mathematical model for the performance of a vibrating screen is developed in terms of an oversize partition curve. This is a normalized curve for any assemblage of particles presented for screening when their size is normalized with respect to the 50 per cent passing size (d50 ) under the prevailing screening conditions. Based on the throughfall aperture (hT) of the wire mesh on the deck, the effects of oversize (% >hT), half-size under (% <0.5 hT), deck location and feed rate were evaluated using the existing screen sizing information. All these variables and also the near-mesh (1.25 hTx 0.75 hT) content (%) of the feed affect the d50. Performance data from different decks of a double-deck screen with various feed rates, size distributions and screen apertures were used to evaluate the near-mesh factor. Effects of wet screening and material bulk density are also incorporated in the model. This generalized model is useful for the simulation of a multiple-deck screen. It furnishes the sieve analysis information of all the deck output streams and therefore has a potential use in the over-all circuit evaluation when used in conjunction with relevant crushing and grinding performance models. An example illustrating the prediction capabilities of the model is given.

Jan 1, 1979

By J. Mrozowski, R. Kurowski, A. Chmielarz, Z. Szolomicki

PbSO4 is a commonly encountered component of the materials used in lead recycling (e.g. battery paste) and in by-products of metallurgical processes (e.g. residues from zinc hydrometallurgy, dust from copper smelting). Smelting of battery paste results in SO2 emission and in generation of significant amounts of hazardous ‘white slag’. Those adverse phenomena can be eliminated by removal of sulphur from the paste. Lead-bearing by-product materials are of polymetallic character with usually low Pb content, which makes lead recovery technologically difficult and uneconomic. However it can be successfully achieved by extraction of lead sulphate from solid phase with triethylenetetramine (TETA) water solutions. That compound has capability for selective solvation of a whole lead sulphate molecule. Virtually pure lead carbonate can be precipitated by means of saturation of lead-loaded aqueous TETA solution with carbon dioxide, and complete regeneration of the extractant is achieved by fixing of sulphate ion into gypsum through operation of calcium hydroxide suspension. The paper presents results of the lab and pilot scale studies into process of battery paste desulphurisation and recovery of lead from the residue of zinc calcine leaching.

Jan 1, 2014

By Robert Yobou, Jacques Naho, Benjamin A. Allou, Jacques Carignan, Huan-Zhang Lu, Jayanta Guha, Koffi Pothin

"Résumé - Les seules productions de columbo-tantalite en Côte d&apos;Ivoire sont effectuées dans les éluvions, colluvions et alluvions d&apos;Issia, au Centre-Ouest de la Côte d&apos;Ivoire. Même si un lien direct avec les roches granitiques est suspecté, aucune attention particulière n&apos;a été accordée à l&apos;étude de la minéralisation primaire en relation avec l&apos;évolution de ces granites et des pegmatites associées. Ces granites, qui sont en intrusion dans les roches sédimentaires du Protérozoïque inférieur, comprennent: le granite orienté à deux micas (type Lobo), le granite orienté à muscovite dominante (type Bitapia) et le granite porphyroïde non orienté à muscovite dominante (type Issia). Les résultats de cette étude indiquent que les pegmatites à Nb-Ta-Be-Li sont liées au granite de type Issia. Les observations de terrain et les analyses sur roche totale montrent que: (1) les trois principaux granites de la région sont de type-S et peralumineux dans leur composition, (2) ils ont été formés pendant la période tardi- à post-Éburnéenne, (3) le granite de type Issia fut le dernier à se former.Les pegmatites liées au granite de type Issia ont été classées en quatre types : A- pegmatites stériles; B- pegmatites à Be; C- pegmatites zonées à Nb-Ta-Be; et D- pegmatites zonées à Be-Nb-Ta-Li. Les pegmatites zonées comprennent les zones suivantes: I- zone à aplite; II- zone graphique; III- zone à albite, microcline, béryl et columbo-tantalite; IV- zone à microcline massive; V- zone à quartztourmaline. Ces pegmatites présentent une zone d&apos;altération métasomatique externe.La minéralisation de Ta, Nb, et Be est liée à la zone III des pegmatites de types C et D, la minéralisation de Li est associée aux greisens qui peuvent être observés n&apos;importe où dans les pegmatites de type D. Les données de terrain et de laboratoire indiquent que le granite de type Issia est la roche parentale des pegmatites à éléments rares de la région. Les pegmatites minéralisées sont distribuées seulement autour du granite de type Issia et les patrons des terres rares des granites et ceux des pegmatites à éléments rares sont très similaires. Les analyses de la composition totale montrent un lien génétique entre le granite de type Issia et les pegmatites à éléments rares. Il est suggéré que les pegmatites ont été formées durant le transport et la cristallisation fractionnée du magma. Les éléments rares sont restés dans le liquide résiduel jusqu&apos;à ce que les conditions favorables à leur précipitation soient atteintes.L&apos;établissement de ce lien génétique ouvre des voies pour des nouvelles stratégies d&apos;exploration."

Jan 1, 2005

By Xueyi Guo

The total production of nonferrous metals in China is 31.35 million tons in 2010, which ranks first in the world for the past ten years. Large quantities of solid wastes including slag, residue, ash, and dust are produced every year in the production of nonferrous metals. These secondary resources are renewable, not only contain abundant valuable metals which can be recycled by metallurgical processing, but also could eliminate the pollution to the environment. In this paper, the status quo of the main nonferrous metals recycling in metallurgical industries in China was summarized, and the future development of waste processing and resource recycling was prospected.

Jan 1, 2011

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: &apos;Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father&apos;s home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers&apos; Delight, 16 miles northwest of Baltimore. Thus far, Tyson&apos;s observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

By L. Vinnett, I. Panire, J. Yianatos, F. Ruiz

"The effect of operating variables on the flotation performance at steady-state has been extensively used for modelling and simulation of separation processes. However, the dynamic characterization of key variables such as gas dispersion (Sauter mean diameter of bubbles, D32, and bubble surface area flux, SB) and froth discharge rate is rather scarce. In this paper, an experimental design allowed identifying the dynamic response of the flotation process in a laboratory scale flotation cell, using a two-phase system, airwater. The installation included automatic control for the superficial gas rate, JG, and the pulp level. Gas dispersion was evaluated in terms of the Sauter mean diameter of a bubble population and the bubble surface area flux, SB = 6·JG/D32. The D32 was measured using the McGill Bubble Size Analyzer (MBSA) along with a semiautomated algorithm. In addition, the froth discharge velocity was measured in real-time using a Visiofroth system. The control variables were the superficial gas rate and the frother concentration (Teefroth). The dynamic characterization of the flotation process is useful to design algorithms that allow the direct or indirect control of metallurgical variables such as flotation rate, concentrate grade and mineral recovery.INTRODUCTIONGas dispersion indicates the way the gas entering a flotation machine is dispersed throughout the volume of the equipment (Schwarz & Alexander, 2006). The gas dispersion is typically characterized in terms of the bubble size (dB), gas holdup (eG), superficial gas rate (JG), and bubble surface area flux (SB =6·JG/dB) (Finch et al., 2000). All these variables have significant impact on the metallurgical performance of flotation machines. For example, Perez-Garibay et al. (2014) investigated the effect of the particle size, bubble size distribution, superficial gas rate and collector dosage on the flotation performance, for the separation of a sphalerite mineral. The authors observed that recovery increased with the superficial gas rate ranging from JG = 0.04 to JG = 0.08 cm/s and also a maximum recovery was obtained for bubble size close to 300 µm. Gorain et al. (1998) reported a strong correlation between the flotation rate constant and the bubble surface area flux in a zinc cleaner circuit. Both variables were directly proportional at three froth depths in the range of hF =7 - 45 cm. Dobby & Finch (1986) incorporated the effect of the superficial gas rate and the bubble size on the flotation efficiency by means of a kinetic model for the rate constants. Yianatos & Contreras (2010) developed a model to estimate the carrying capacity in large flotation cells by including the bubble surface area flux."

Jan 1, 2016

By T. Niedoba

Coal as an energetic raw material is characterized by many features that determine its quality. The data concerning coal are usually treated as independent values, despite the fact that this kind of approach is not always appropriate. In the paper the dependencies between sulfur contents and volatile components in coal and particle size and density were analyzed. The method of ordinary kriging is applied to experimental data to describe this relationship; this method can be used for particles of any size and density. An example of the application of this technique is presented for energetic coal Type 31, originating from one of the Polish hard coal mines in Upper Silesia. Results from ordinary kriging are in good agreement with experimental results. Similar analyses can be performed for other properties of coal material, such as ash content, Roga number, and moisture. On the basis of the data obtained by ordinary kriging, a more comprehensive multidimensional model is described, which can characterize certain deposits or strata from which the analyzed materials originate. This is superior to basing the model only on experimental data, which often is limited by size of the sample. The results obtained by ordinary kriging applied to various types of coal would allow more precise analysis of individual properties of the studied materials and increase the ability to determine significant differences between them. This method can be also applied to other types of mineral raw materials, such as copper ore.

Aug 1, 2013

By Y. Duna

The reliability of mine ventilation systems is critical to normal and safe production in a mine and includes reliability of the following parts: ventilation system branch (or passage), ventilation structures, ventilation network, and the fan. Among these, the reliability of a ventilation branch may be considered the foundation of the whole ventilation system. The branch ventilation flow includes four parameters: air volume; toxic and hazardous gas concentrations; temperature, and dust concentration. The calculation model for the reliability of a branch was established based on the analysis of normal distribution of flows in any one branch. Then, the efficiency of the ventilation structures and fire risk compromising the reliability of branch was studied. The results obtained were as follows: if the air volume, toxic and hazardous gas concentrations, temperature and coal dust concentrations of the branch are within reasonable limits, set at any stable state and at the same time, then this branch is reliable.

Aug 1, 2013

By Eugene Sun, Qiang Xu

This presentation will review current applications of composite materials in aircraft design and discuss the challenges involved in maximizing the potential of the composites in aircraft applications.

Jan 1, 2010

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By R. G. Eggert

"A critical element, as the term has come to be used, provides essential properties to a modern engineered material and is subject to supply risk. The rare-earth elements became perhaps the most prominent of the critical elements in recent years because of their important uses in permanent magnets, advanced lighting, and military materials; the geographic concentration of production in China; and the dramatic run-up in prices in 2010-2011 followed by price collapse between 2011 and 2016. Yet criticality extends beyond the rare earths. What is critical depends on your perspective – who and where you are, and when you ask. This paper reviews the many perspectives on, or faces of, critical elements. It compares and contrasts perspectives of industry (General Electric), national or regional manufacturing sectors (Japan, European Union), emerging energy technologies (as seen by U.S. Department of Energy and, separately, Joint Research Centre of the European Commission) and the world as a whole (as evaluated by academics). This comparison reveals a diversity of not only perspectives but also methodologies and time frames of concern.INTRODUCTIONRare-earth elements appeared prominently in the news in 2010 and 2011 because of the dramatic increase in their prices; their important uses in permanent magnets, advanced lighting, and military materials combined with the geographic concentration of production in China, which reduced export quotas significantly. Rare earths became the most prominent of what have become known as critical elements or materials – that is, those that provide essential properties to modern engineered materials and yet are subject to supply risks.Yet criticality, the state of being both essential and subject to supply risks, extends beyond rare earths. What is critical depends on your perspective. This paper begins by reviewing a little history and presenting a general conceptual framework from which to think about critical materials. It then reviews the many perspectives on, or faces of, critical elements – corporate, national, and global, as well several that focus on emerging energy technologies. The paper concludes with thoughts on what to do to mitigate the potentially negative effects of the supply risks associated with criticality."

Jan 1, 2016

By A. R. Hekmat

Hypereutectic Al-Si alloys are used in applications that require high resistance to wear and corrosion, hardness and low coefficient of thermal expansion, To maximize the properties of these alloys, semi-solid processing can be utilized to modify the solidification structure of the primary silicon crystals as well as to reduce microsegregation and porosity, The transformation and spheroidization of primary Si crystals by shearing in the semi-solid state are not fully understood as they precipitate in the presence of other alloy phases, The objective of the present work is the determination the rheological characteristics of A390 (Al-17%Si-4,5%Cu-0.5%Mg) alloy using a Couette type (Haake RV12) viscometer and examining the microstructural evolution during continuous cooling and isothermal shear rate experiments, The effect of shear rate, solid fraction (temperature) and morphological evolution of the silicon crystals are investigated.

Jan 1, 2005

By R. N. W. DiLabio

"In a continuing program of mapping glacial dispersal trains, near-surface till samples were collected down-ice from a copper-silver-gold prospect at Onaman River, Ontario, and down-ice from the past-producing gold district at Oldham, Nova Scotia. The program is designed to aid exploration by illustrating glacial dispersal from various types of known occurrences and by identifying postglacial processes that control drift composition at a detailed scale.Native gold was mined at Oldham from arsenopyrite-bearing saddle reef quartz veins in a dome in Early Paleozoic slates of the Meguma Group. Gold abundances greater than 10 ppb in till form a dispersal train at least 1900 m long. Gold abundances between 40 and 100 ppb occur in clusters up to 600 m down-ice from gold-bearing bedrock. Anomalous arsenic abundances in till form a broad train 1100 m long that is significantly different in shape from the gold train.At Onaman River, subeconomic amounts of Cu-Ag-Au occur in quartz lenses in Archean mafic volcanic rocks. A dispersal train defined by the distribution of mineralized boulders and increased abundances of Cu, Ag and Zn in till extends 600 m down-ice from mineralized bedrock. Gold abundances between 10 and 70 ppb do not define this dispersal train, but occur instead in clusters 300 to 600 m down-ice from mineralized bedrock. In vertical sections in the upper 2 m of copper-rich till, Au abundances vary sympathetically with Ag and Cu levels; however, there seems to be no preferential site of Au enrichment in the mineral portion of the soil profile.Several of the mineralized boulders at Onaman River are richer in Au and Ag than the mineralized bedrock from which they were derived. Although some of the high Au and Ag assays were caused by biased sampling of sulphide-rich portions of the boulders, many were caused by leaching of sulphide minerals from 'the boulders, which left a limonitic boxwork that is enriched in Au and Ag. A few of the Au-rich boulders may have been derived from an unknown bedrock source."

Jan 1, 1982

By K. Sinding, R. Poulin

"Recent land-use decisions in British Colwnbia, and the publication of a report on compensation for expropriations of resource interests, have highlighted the nature of land use policies. Landuse decisions, such as the creation of large new parks, raise three principal issues which have implications for how land-use policy is conducted and how it impacts on the mining industry. The first is the identity of the parties advocating different land-use policies and their motives for doing so, the second is the changing nature of benefits derived from land, and the third is the change of property-rights regime which is devised to accommodate the (changing) benefits from using land and natural resources, as well as the interests of the different parties involved.Involved Parties and BenefitsThe process of establishing or modifying property rights depends on the interest groups involved. Three distinct categories, each with distinct incentives which can influence the process, must be distinguished: private claimants, politicians and bureaucrats (Libecap, 1989).The first groups claim rents and management powers through asset ownership. They may be incumbent owners seeking enforcement of the status quo, new claimants seeking redistribution of assets, or third parties who depend on the distribution of assets (e.g. lenders, labour suppliers and contractors). Some infonnal property arrangements can be negotiated within the group whereas others requires action in the political arena through lobbying politicians for (re)allocation of property rights and influencing bureaucrats for favourable administrative decisions. The second category is politicians, who direct the powers of the state to change or enforce property rights. Both incwnbents and office-seekers fall in this category and their actions and opinions are shaped by their constituencies and financial backers. However, not all causes can be championed and trade-offs have to be made, resulting in decisions that maximize political benefits. The third category of parties in the process is the bureaucrats. The power to manage has been delegated by politicians but bureaucrats also have opportunities and incentives to further their own interests. These can include maintaining or expanding jurisdictional turf or increasing operating budgets (Libecap, 1989)"

Jan 1, 1994