Search Documents

By I. I. Bethcherman

Introduction 1.-lmportance of Physical Nature of Condensates The metals of commercial interest which have reasonably high vapour pressures below 1,200° C. are mercury, cadmium, sodium, zinc, magnesium, lithium, and calcium. With the exception of mercury, these metals occupy high positions on the electrochemical series and form compounds with very high negative free-energies of formation. It is highly desirable that such metals should not be produced in a form which is finely divided, on account of their reactivity with atmospheric gases. Powders of magnesium, calcium, and even zinc (blue powder) are dangerous to handle and cannot be coalesced by simple melting techniques. Vaporization in vacuo forms a convenient method of handling and purifying the alkaline earth metals in particular and a previous paper by the authors dealt with some of the factors controlling the separation of metals by this technique (12). An essential part of the operation is the condensation of the vapour to produce a massive deposit which may be conveniently melted and handled by established metallurgical techniques. This investigation sought to determine the conditions affecting the nature of solid condensates.

Jan 1, 1951

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013

By P. R. G. Brandão, E. E. Ferreira

The presence of metallic cations in solution will affect the aggregation or dispersion of the fine hematite particles, depending on the type of cation adsorption: either specific or non specific adsorption. In this work, the zeta potential measurements were carried out on a sample of pure hematite as a function of pH and metallic cations concentration (Ca2, Mg2+, Mn2+, K+, Na+ and Al3+). The objective of these studies was to clarify the effect of these metallic cations on the surface chemical properties of pure hematite. The cations K+ and Na+ adsorbed as non-specific species and caused only the reduction on the values of zeta potential (in terms of absolute value) over the entire range of pH values tested. For the Al3+ cation, in the acidic pH range it adsorbed as a specific species and increased the zeta potential values. The cations Ca2+, Mg2+ and Mn2+, adsorbed as a non specific species at pH levels less than 6.0 and caused the reduction of zeta potential due to the compression of the electrical double layer. However, for pH values greater than 6.0, these cations adsorbed as a specific species causing the zeta potential to increase and became more positive as the pH value increased (alkaline). This effect could be due to the adsorption of some hidroxy complex species of these cations, which contributed to the positive charge. The effect of metallic cations (Ca2+, Mg2+ and Al3+ concentration, at pH 4.0, 7.0 and 10, showed the following results: a) at pH 4.0, increasing the concentrations of Ca2+ and Mg2+ resulted in on a small reduction in the value of the zeta potential. At this pH, increasing the concentration of A131 cations caused the zeta potential to increase due to specific adsorption of a negatively charged Al3+ hydroxy complex b) at pH 7 and 10, increasing the concentrations of Ca2+ and Mg2+ caused the zeta potential to change its charge from negative to positive.

Jan 1, 2004

By Shanjun Mao

This paper summarizes current achievements of Digital Mining in China, puts forward the concept, framework and key technology of Smarter Mining, and finally points out that there is still a long way to go in order to acheive Smarter mining.

Aug 1, 2013

By K. Stankiewicz

Projects as regards state-of-the-art mechatronic systems aiming at increase of safety in the mining industry and at improvement of coal production technologies, which have been completed at the KOMAG Institute of Mining Technology, are presented. These projects cover automation, monitoring and visualization systems, systems for implementation of artificial intelligence techniques, and database recording systems. iRIS system for electronic marking, identification, and recording of components of powered roof supports, which was implemented in 31 Polish mining enterprises, is presented as an example of the work directly associated with an increase of operational safety. Specialists from KOMAG, ELSTA, Ltd., and Silesian University of Technology in Poland, have developed flexible, configurable, and scalable system for data management, which refers to all fixed assets of mining enterprises, meeting the requirements of users as regards marking and identification of fixed assets. The system for control of roadheaders using intelligent algorithms, based on artificial intelligence techniques is also the example of innovative actions. This system aims at increasing the safety and effectiveness of teamwork due to a possibility of remote, semiautonomous operation. Introduction of artificial intelligence technology enables adaptation of roadheader mining system to the present mining-and-geological conditions. Moreover, work aiming at implementation of state-of-the-art system for control of mine jig?s beneficiation node, integrating machines and equipment in one system, is carried out as regards automation, information integration, and visualization in coal beneficiation process. Work on recovery and conversion of thermal energy, which is a by-product during operation of machines and equipment, especially mine diesel drives, is presented. Systems for energy recuperation are more and more important due to the necessity of continuous increase of power production efficiency.

Aug 1, 2013

By M. Imamura

Sumitomo Metal Mining Co., Ltd. has developed a novel hydrometallurgical process for producing not only copper metal but also iron metal from copper concentrates. Because copper concentrates generally contains the same amount of iron as copper, cost-effective rejection of the iron is a key issue for the development of the process. Conventional hydrometallurgical processes produce a large volume of goethite or hematite for disposal and the residues are not environmentally friendly. In the novel Sumitomo hydrometallurgical process, copper is leached effectively from chalcopyrite concentrates using chlorine gas, followed by purification through solvent extraction and electrowinning for copper and iron recovery. This process has many advantages such as the minimization of the volume of solid waste by the recovery of metallic iron and the production of high purity copper. Iron metal with a purity of more than 98% can be recovered from the purified raffinate. This paper presents the results of the batch and continuous tests of the process flowsheet.

Jan 1, 2006

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

By Nawshad Haque, Leanne Smith, Hal Aral, Joseph Cho, Warren Bruckard

"Water availability is one of the principal parameters in determining the feasibility of mining projects in arid and semi-arid regions. The volumetric water footprint (VWF) of a conceptual model of a copper flotation plant was found to be 2.45 kL/t Cu ore, compared with an actual measurement reported in the literature of 2.72 kL/t Cu ore. The flowsheet considered included mineral processing stages such as crushing, screening, grinding, classification, separation, flotation, thickening and filtration. The effect of a number of variables on the VWF was evaluated, including solid/liquid ratio, feed mass flowrate, ore loss, water loss, moisture content of ore, ore grade and water recycling. The use of seawater with recycling provided the most environmental and economic advantage among several scenarios evaluated. The study assumed a price of $1/kL freshwater, $4/kL for transport over a 200 km distance at 2,000 m altitude and $4/kL for water treatment. The water related cost of the desalinated seawater use scenario was A$493/t Cu concentrate, while the water related costs of fresh water and blended water scenarios were A$308/t and A$268/t Cu concentrate, respectively. The water related cost (fresh water scenario) accounted for 44% to 49% of the entire mining and processing costs that included drilling, blasting, loading, hauling, crushing, grinding and concentrating. The total overall cost was A$435/t Cu concentrate for the seawater with recycling, compared to A$451/t Cu concentrate for the fresh water with recycling case.INTRODUCTIONReducing the water footprint (WFP) by utilising alternative water sources has been a focus of mining projects due to increasing concerns about water scarcity and growing energy costs. The global mining industry can expect to experience fresh water shortages in the future, and saline or hyper-saline water may be the only available water source to process minerals in arid regions. Extensive studies on alternative water sources (e.g. seawater, desalinated seawater, blended water) and the reuse of process water have recently been conducted (Moreno, Aral, Cuevas, Monardes, Adaro, Norgate & Bruckard, 2011; Aral, Mead, Cuevas, Davey & Bruckard, 2010). Such studies provide sustainable and economic strategies for mines and concentrators in the arid or semi-arid regions of the world such as in Chile, Peru, Indonesia, and Portugal. More work, however, is needed to confirm water consumption data for different base metal flowsheets and use this data to develop water models that can lead to reduced WFPs and more sustainable water usage in the mining industry."

Jan 1, 2016

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

INTINERARY ?What is SRI? ? How do we define good corporate social and environmental performance in the mining and petroleum industries? ? Why should you care? MJRA Inc. ? Established in 1992 ? Canadian Social Investment Database (CSID) launched in 1993 ? Jantzi Social Index launched in January 2000 ? created in 2000 SRI is ?the incorporation of social and environmental parameters into the investment decision making process.

May 1, 2002

What Discounted Cash Flow Analysis can do for you: ?Provide an accurate financial analysis of a project for the first 25 to 30 years of operations ?Identify cash flow requirements ?Identify relative sensitivity of the project to the various input parameters ?Place a value on the resource in place after 30 years of operations ?Correct for errors in input parameters

May 1, 2010

By Timothy W. Ellis, Abbas H. Mirza, R. David Prengaman

Recycled lead, i.e. material produced by the recycling of lead-acid batteries, has become the primary source of lead in much of the world. This has been important to the recycled lead industry as other uses have dwindled, e.g. lead based pigments, chemicals, fuel additives, solders and CRT glasses. Presently, battery manufacturing accounts for greater than 85% of lead consumption worldwide while recycled lead accounts for approximately the same market share of lead supply. Battery manufacturing and production of recycled lead are intimately coupled. In 2007, of all the industrial base metals, lead from lead-acid batteries had the highest recycling rate in North America at greater than 95%. In this paper we will review some of the processes and technologies used in a modern lead acid battery recycling facility, and how recycled lead has become the material of choice for battery construction through the development of a recovery and refining process that exceeds the industry requirements. We will also briefly review an advanced air emissions treatment system in a modern lead recycling plant that demonstrates the feasibility of a new maximum available control technology (MACT) for secondary lead smelters.

Jan 1, 2011

By E. L. Bruce

EUROPEAN Russia is mainly a great plain, the average elevation of which is only 600 feet above sea level and the maximum elevation less than 1,200 feet (Figure 1). The main divide between the Arctic ocean and the Black sea and Caspian sea is an indistinguishable topographic feature from which the Dneiper and Don rivers flow southward to the Black sea and the Volga river to the Caspian. The valleys of these rivers are but little below the general level (Figure 2). To the south, this great, rolling plain is broken by a low ridge of Precambrian gneisses and intrusive rocks. The Crimea is an upland from which the descent to the Black Sea coast is precipitous (Figure 3). The Ukrainian Soviet Socialist Republic occupies the southern part of the plain. It is the southwestern unit of the Union, bordered by Rumania and Poland on the west and by the Crimean Soviet Socialist Republic on the south.

Jan 1, 1938

By Charles Graham

It is the general belief that the coal deposits on Vancouver Island are extremely large, and easily available. Indeed, they are frequently described by prominent public men and by writers in the press as "illimitable" and "inexhaustible." It is well that the facts that have been established as a result of seventy years of surface prospecting, underground operations and extensive diamond-drilling in this coalfield should be disclosed. HISTORY The presence of coal on the coast of British Columbia was first made known by Dr. W. F. Tolmie in 183 5. This coal was brought to him by Indians from the north-east coast of Vancouver Island, probably from Suquash. In 1850 the existence of coal at Nanaimo was announced by Mr. ]. W. MacKay. Development was started in 1852, and coal was shipped before the close of 185 3. The first operations were carried on by the Hudson's Bay Company, who operated the mines until 1861, when they sold them to the Vancouver Coal Mining and Land Company. Practically all of the operations in the immediate vicinity of Nanaimo have been carried on by this Company and its successors. In 1869, Mr. Robert Dunsmuir discovered coal about five miles north-west of Nanaimo, at Wellington. The Welling-ton Colliery Company was organized, and began to produce coal from the Wellington mines in 1871, the coal being shipped from Departure bay. This colliery was a large producer for several years, but was finally closed in 1900.

Jan 1, 1924

By B. Currie

Maintenance of quality electrowon copper requires an electrolyte which has suitable chemical and physical characteristics. The proper design and operation of the solvent extraction plant is essential to the quality of the electrolyte sent to electrowinning. An aspect that is not well appreciated is that the return electrolyte can have negative effects on the operation of the solvent extraction plant. Poor SX plant operation creates below optimum electrolyte conditions. High Eh in the return spent electrolyte can degrade the SX reagent with large decreases in copper transfer capacity and increases in internal entrainment. The synergistic interaction of the SX and EW plants needs a single-source design approach to address the interactions. The design elements in the SX and EW plants required to manage the electrolyte conditions are discussed.

Jan 1, 2014

By Xue Yang

Even though many approaches have been proposed for automated fault detection and diagnosis of Heating Ventilation and Air Conditioning (HVAC) systems, and advanced maintenance programs, such as preventive and predictive maintenance have been applied for the systems, issuing work orders for corrective maintenance is still a reality. Currently corrective maintenance still accounts for more than 55% of all maintenance programs in average facilities in the US (DoE, 2010). Indoor air related problems are especially important among corrective maintenance work orders. This paper provides details of a case study conducted to capture the workflow that HVAC mechanics follow, their rationale in diagnosis process and the information they typically refer to while responding to indoor air related corrective maintenance work orders. The general workflow for HVAC mechanics to complete such types of work orders was summarized into 5 stages, and generic information requirements recorded from the case study were synthesized. Initial findings show two main challenges in the industry for HVAC mechanics to get access to required information, which highlights the need for a systematic approach that would enable identification of such information applicable to a given context under which a work order has been generated and provide values of required information for HVAC mechanics to do sound diagnosis through integrated data repositories.

Aug 1, 2013

By P. E. Weidmark

"Energy, Mines and Resources Canada has published the first in a new series of reports that will examine selected mineral products that are imported.""Vanadium - An Imported Mineral Commodity"" looks at one of the 32 raw materials for which Canada currently is totally dependent on foreign sources of supply. Vanadium is used in Canada mainly as an alloying element in the manufacture of high-strength, low-alloy (HSLA) steels.The series will examine the supply systems for various selected imported non-fuel minerals, as an aid to developing policies that might lead to reduced dependence on external sources. Each report in the series will address a numberof questions:What countries do the mineral and its principal sub-products come from?How do they get to Canada?What are they used for?How vulnerable is the supply chain to disruption?Are there alternative sources?Are substitute materials available?In summary - how serious is Canada's supply problem for the mineral in question, and what should be done about it?Mineral Bulletin MR 188, ""Vanadium - An Imported Mineral Commodity"", is available for $3.00 ($3.60 outside Canada) from authorized government bookstore agents and many other bookstores, or by mail from the Canadian Government Publishing Centre, Hull, Quebec, KIA OS9."

Jan 1, 1981

By H. Golzarpoor

Life Cycle Analysis (LCA) is a methodology for evaluating the environmental impacts associated with a product during its life cycle. LCA is identified as the most reliable method for verifying environmental impacts; however, current LCA-based approaches have certain limitations for environmental analysis of construction products. Integration of the LCA methodology with Discrete Event Simulation (DES) provides a sound framework for modeling and analysing the environmental impacts of construction products. LCA and DES is one possible combination for analysing the cause and effect of various scenarios where time, resources, and randomness of input variables affect the outcome and, therefore, has the potential to address the shortcomings of LCA in construction. Recent studies in disciplines other than construction such as manufacturing systems have revealed positive effects on evaluation of environmental metrics while integrating LCA with DES; however, this integration has not yet been applied for environmental analysis of construction products. By implementing LCA data in a DES model, this research proposes an environmental model of earthmoving operations in a case study. Environmental variables are simultaneously assessed with production variables in the same simulation model and the integration of DES and LCA is discussed.

Aug 1, 2013

By Roger T. Laine

"The Carswell structure, located in the western part of the Athabasca Basin, northern Saskatchewan, has been extensively explored since 1967. This exploration has been successful and lead to the discovery, in 1970, of the D sandstone-hosted unconformity related deposit. By the end of 1984, five additional basement-hosted unconformity related deposits had been delineated: the OP and N discovered in 1970, the Claude in 1971, the Dominique-Peter in 1981, and the Dominique-Janine in 1984. The D deposit has been mined out; the Claude open-pit has already produced more than 500 tonnes of uranium, the development of the Dominique-Peter underground mine (first phase) has been completed, and production from the latter started in 1985.All six deposits are located in the southern part of the Aphebian metamorphic core, 18 km in diameter, which has intruded at least 1250 metres of Helikian Athabasca Group sediments during a cryptoexplosion event at 480 Ma, unrelated to the emplacement of uranium mineralization. The metamorphic rocks, affected by the Hudsonian Orogeny, are divided in two lithostratrigraphic units: the Peter River gneiss, aluminous gneiss series, and the Earl River complex, mixed quartzofeldspathic and mafic gneiss series. A well developed regolith profile is recognizable in the south along the contact with the sandstone and inside the metamorphic core sometimes associated with conformable sandstone beds.Basement and sandstone-hosted uranium deposits show many similarities:-linkage to unconformity;-mineralogy and geochronology with a first phase mineralization characterized by a polymetallic sulphide-uraninite-brannerite assemblage dated at 1150 to 1050 Ma, a second phase characterized by a simple sulphide-uraninite assemblage dated at 890 to 820 Ma, and a third phase characterized by a pitchblende-hematite dated at 380 Ma; and,-linkage to early Hudsonian structures with remobilization of these structures during intense hydrothermal alteration resulting in Mg chlorite-illite halos."

Jan 1, 1986