Search Documents

By Colin Jones

Canadian Clay Products Inc., which mines bentonite in Saskatchewan near Truax and operates a plant at Wilcox, is the sole producer of swelling bentonite, often called western bentonite, in Canada. Seven products produced by the company are used in binders, sealants, water and waste water treatment, plasticizing agents, foundries and absorbents. Reserves are reported at about one million tonnes for the deposit but the area in general contains significant additional reserves.

Jan 1, 2001

By R. Q. Honaker

It has been shown that naturally hydrophobic carbonaceous materials such as coal and graphite can be selectively coagulated and separated from hydrophilic impurities without using oily agglomerants, flocculants or electrolytes. The coagulation occurs at C-potentials significantly higher than those predicted by the classical DLVO theory, suggesting that it is driven by the hydrophobic interaction. In the present work, the energy barriers for the coagulation of a hydrophobic coal sample have been calculated using the extended DLVO theory which incorporates the hydrophobic interaction energy in addition to the dispersion and the electrostatic energies. For the coagulation of minerals present in the coal, the classical DLVO theory has been used for the energy barrier calculation. The results of these calculations provide an excellent correlation with the results of a series of Selective Hydrophobic Coagulation (SHC) tests conducted with run-of-mine coal and graphite samples.

Jan 1, 2004

By J. S. De Lury

The metalliferous areas of Manitoba have been described in more or less detail. Since the descriptions were written some new prospects have come to light and considerable mining development has taken place in two or three localities. No attempt will be made in this paper to give an account of recent activities or to describe the several areas in detail. In a general way, geological conditions are similar in all metalliferous areas of the province, a similarity that invites a discussion of the prospects as a whole, the features that are common to all deposits and the reasons for their uniformity. Modern theories of metallogenesis have a direct bearing on such a discussion and an effort will be made to show their application.

Jan 1, 1925

By E. S. Moore

Introduction The geology of the Sudbury nickel field has been studied extensively, but there are few reports dealing with the structure of the interior of the basin. It was not until the Treadwell-Yukon zinc-lead deposits were discovered that attention was strongly directed toward the large-scale faulting that has split the basin parallel to its long axis. This faulting has been responsible for the , ore deposits in the basin and it may be regarded in many ways as the most important geological event, next to the intrusion and differentiation of the nickel eruptive sheet, that has occurred in the Sudbury region. The early reports on the nickel region by Bell, and Barlow, were chiefly concerned with the nickel-copper ores and with the formations of the region. Coleman was the first geologist to map the nickel eruptive as a continuous sheet around the belt and to emphasize its basin character. On the map accompanying his later report, he shows an important offset in the nickel eruptive at its southwest end, where the large fault cuts this portion of the basin, but the fault was not traced into its interior, as little detailed work was clone in the basin at that time. No ore-bodies had been developed outside of the nickel-copper deposits associated with the norite when the map was prepared, and attention was mostly concentrated on the nickel eruptive. Coleman did, however, map and name the various formations found within the basin and, in general, his delineation of these has remained the standard for prospectors and other workers in the field until the present day.

Jan 1, 1930

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By John Hansen

This paper has been written for presentation at the 103rd Annual General Meeting of the Canadian Institute of Mining, Metallurgy, and Petroleum, April 29 to May 02, 2000. The paper addresses blast pattern fragmentation and diggability versus the blasting technique used. RESUME The author is the Vice President for Thunderbird Mining Systems. In this capacity he manages the mine site installation of surface mining mobile equipment monitoring and navigation systems. These systems are onboard instrumentation and software systems designed to: ??measure and log mobile equipments? production and health; and ??direct the equipment operators via onboard displays that show comprehensive maps and engineering instructions. The author is a mining engineering graduate from the Royal School of Mines. His work experience includes front line supervisor and mining engineer for Hudson Bay Mining & Smelting, mining engineer for Teck Corporation, and mining consultant for PriceWaterhouseCoopers.

May 1, 2001

By W. A. Jones

Purpose of Paper Geophysics is a highly developed science which has found a wide use in industry. Perhaps the most spectacular application has been in the field of oil exploration. It has been estimated that, up to the end of 1939, geophysics was responsible for the discovery of five billion barrels of oil. In 1944, the sum o $40,000,000 was expended for geophysical work in the search for new oil deposits. Although the metal mining industry has so far made comparatively little use of the science, it is becoming increasingly common for the exploration engineer or geologist to be required to co-operate with the geophysicist. Many papers dealing with applied geophysics have been published but in most of them advanced training in physics and mathematics on the part of the reader has been assumed. It is difficult for the average engineer to obtain a ready understanding of the equipment, field procedure, and scope and limitations of the science from the literature. The present paper attempts to describe briefly and in simple terms the principles underlying magnetic, self-potential, and electrical resistivity methods and their application to a field problem. Introduction Geophysics is concerned with the study of gravity, magnetism, natural earth currents, earthquakes, vulcanism, and many other natural phenomena. The methods, originally devised for the measurement, for scientific purposes, of the forces associated with such phenomena have been adapted to the search for buried deposits of economic value. If the body sought has large dimensions and distinctive physical properties, geophysical measurements may reveal associated, and in some cases quite characteristic, anomalous features. However, in many instances the mass cannot be indicated directly but has a common association with geological features which can be defined by physical measurements. Although such surveys cannot specifically identify oil, metalliferous minerals, or other commercially valuable substances, it is possible to delineate anomalous sub-surface physical features which, with the help of geological information, can be assessed as possible or probable indications of the body or structure sought. The nature and extent of the material causing an anomaly, and its economic importance, can only be determined by further exploration, such as drilling.

Jan 1, 1947

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949

By W. L. Brown

"The properties of Base Metal Mining Corporation are in Yoho Park about 2 1/2 miles northeast of Field; British Columbia; on the main line of the Canadian Pacific railway. There are actually two mines; the Monarch on mount Stephen and the Kicking Horse on mount Field; separated by the steep valley of Kicking Horse river. The outcrops of the orebodies range from 4; 900 feet to 5; 300 feet above sea-level. The concentrator is situated below the Monarch mine and is connected to the main portal by an aerial tramway. The ore from the Kicking Horse mine is conveyed by aerial tramway to a storage bin on the main highway and is then trucked to the concentrator.During the construction of the Canadian Pacific railway through Kicking Horse valley, galena float was found at the base of mount Stephen. The East Monarch outcrop was staked in 1894. The outcrop of the West Monarch ore body on the cliff face of mount Stephen was not discovered until 1916. The Kicking Horse orebodies on mount Field were discovered a few years later. In 1912, a 75-ton concentrator was erected, which operated at intervals until 1924. During this period approximately 42,000 tons were mined and milled, largely from the East Monarch orebody. In 1928, the Base Metal Mining Corporation, Limited, was formed to take over the Monarch and Kicking Horse mines. A 300-ton differential flotation concentrator was erected and production started in the autumn of 1929. In a very short time, however, the low price of metals forced the mill to shut down until August 1933. From 1929 to 1935, when the mill again ceased operation, a total of 256,500 dry tons of ore, averaging 1.59 oz. silver per ton, 9.7 per cent lead, and 12.6 per cent zinc, was mined and milled, largely from the West Monarch orebody. After a period of further underground development, the concentrator reopened in 1940 and is still in operation. From 1940 to the end of 1944, 354,363 tons of ore was milled, averaging 5.32 per cent lead and 10.47 per cent zinc."

Jan 1, 1954

By W. R. Bacon

"MAGNETITE HAS BEEN found in many .parts of the coastal area of British Columbia, but the more important deposits are on Vancouver Island and Texada Island. The locations of these deposits are shown on Figure 1.Interest in the magnetite deposits dates back to the 1870s, when land was acquired on the southwest coast of Texada Island by the Puget Sound Iron Company. This ground included the Prescott, Paxton, and Lake deposits. During the years 1885 to 1903, and 1908, 28,898 tons of magnetite ore was shipped to the company's blast-furnace plant at Irondale, Washington, U.S.A. This production was almost entirely from the Prescott open-pits.In the years following the Texada Island discoveries, other magnetite deposits were found in the coastal area, and various plans were proposed to utilize the local ores in the establishment of a steel industry in the Pacific Northwest. None was carried to fruition but, in 1951, open-pit mining was begun at Iron Hill, Vancouver Island, to furnish iron concentrates for steel mills in Japan. In 1952 mining of the Texada deposits was resumed to supply the same market. Production figures for these recent operations are as follows:"

Jan 1, 1949

By Vic Casaletto

"IntroductionThe Canadian mining industry is under immense pressure to compete with foreign mine operations. The very survival of the Canadian mining industry is threatened by lower ore grades, environmental pressures, high cost of labour, unfriendly tax laws toward exploration and the increasing cost of new technology. In order to compete in the world market, Canadian producers and their suppliers are rethinking age old customer-supplier relationships in favour of preferred supplier relationships which can improve the profitability and enhance the competitive position of both partners.This paper attempts to redefine partnerships with suppliers in the context of a ""win-win"" objective. It will outline the measurable benefits to both partners through a representative product which highlights the keynote structure of any successful supplier partnership The Status Quo...Mines all over North America are plagued with the same recurring questions, ""Who has the best product for my operation at the lowest price... How do we know a product will perform to a supplier's projections after the sale...What do we do if the product fails to perform as expected?"" These questions have been asked by underground mining operators for decades but rarely have long-term solutions with measurable results been achieved.The LHD industry is one example of the status quo where partnerships will provide large gains toward technological advancement, reducing mobile equipment costs. The underground mining industry is out of sync with their surface counterparts in the open pit business.Partnerships with suppliers in the open pit world are not only a standard practice but a culture which has existed for decades. Open pit operators enjoy concepts which fix their mobile equipment costs for the life of the mine and hold the equipment supplier accountable for performance and fleet economics for 60 000 service hours and longer.Manufacturers are attempting to transfer this culture into the underground mining industry. Figure I illustrates the significance of a capital driven decision."

Jan 1, 1994

By Ken Musgrave

"What Most Effective Management Does?It must satisfy the demands, of three groups of people: owners, employees and the public.OwnersOwners want profitable operations that will pay them a return on their investment, plus operations managed for long life. Many owners are also concerned with employee's well being and their company's public image.EmployeesJob security and a good income are probably still the most important demands, however, as time goes by, employees are also demanding more involvement in safety issues, working conditions, and even how work is done.The PublicThe public requires acceptable environmental standards, as well as enjoying the prosperity supplied by a successful operation.How are Mines Managed?Most mines are managed very traditionally. The basic credo is that the managers make the decisions, and the hourly, and junior salaried employees do what they are told. Clearly this is the extreme case, epitomized by the long service shift boss who might say ""It took twenty-years to become a shift boss, and no miner is going to tell me what to do"" .There are some exceptions, two notable ones being Campbell-Chibougamau, and T.G.S. (now Kidd Creek Mines) which, in very different circumstances, decided on a more participative style.Campbell-Chibougamau, having closed down due to unprofitable operations, reopened, using a team structure with working leaders, and a system for sharing gains against cost targets with employees. Although the system has some problems, and development miners are bonused conventionally, this has been a basically successful program.Texasgulf Sulphur, a company with a history of non-union operations, and a participative management style, made a corporate decision to operate their Kidd Creek Mine in the same way. The orebody was rich enough to allow them the luxury to do this, but they have never had a strike, so perhaps they have more than saved the cost of the benefits and salaries they needed to pay. They also reward employees with a stock distribution scheme based on service and earnings."

Jan 1, 1985

By K. E. Waters, M. Mirnezami, R. Gauvin, A. Jordens, K. W. Malas

"There is currently very little information on the physico-chemical properties of rare earth elementbearing minerals, or on their processing. With the increasing demand for rare earths, this is something that needs to be addressed. This paper introduces some surface chemistry analysis of fergusonite (YNbO4), and the bubble-particle attachment. Zeta potential measurements indicate adsorption of sodium oleate and, to a lesser degree, potassium amyl xanthate onto the surface, and an increase in attachment to an air bubble is observed at pH 4.5 and 6.5. At a pH of 10.5, no attachment is observed, whether in the presence of the reagents or not. This analysis, although initial, will be used to initiate flotation tests, in order to facilitate the selective recovery of fergusonite. INTRODUCTIONRare earth elements (REE) are increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. An article in the New Scientist highlighted the importance of a number of REE, many of which most people are be unlikely to have heard mentioned (Crow, 2011). From batteries (lanthanum and cerium) to magnets (dysprosium and neodymium) and lighting (yttrium), the REE are crucial to the advancement of technology and energy saving devices. For example, neodymium is finding most use in the high end magnets that keep the motors turning that power wind turbines and electric cars. In the case of yttrium, the demand outstripped the supply in 2010, emphasising the need to develop deposits containing this and other REE (Crow, 2011). The impact of our dependency on REE has become even more apparent with the reduction in exports by China, which currently controls 97 % of the world’s rare earth production (Pitts, 2011).With the increasing demand for rare earth elements (REE), there is a drive to exploit the known resources around the world. However, the physical beneficiation of the rare earth element bearing minerals is a subject which will require a great deal of investigation to fill the knowledge gaps surrounding these developing rare earth projects. There are numerous articles on REE mineralogy as well as the hydrometallurgical processing of REE concentrates (Alex, Suri, & Gupta, 1998; Peter Gromet & Silver, 1983; Ring et al., 1993; Schnetzler & Philpotts, 1970; Uda, 2000), however a common feature amongst these resources is the lack of detailed descriptions of the physical beneficiation processes required to concentrate REE-bearing minerals. There is work being conducted into reagents and methods for use in recovering some rare earths from their associated ores (Bulatovic, 2010; Ni, Parrent, Cao, & Liu, 2011), but much more in-depth research is required."

Jan 1, 2012

By G. W. Harris, P. Mousset-Jones, J. Daemen

"To minimize ore dilution induced by blast movement in surface mines, it is necessary to quantify such movement. This will enable more accurate location of the grade boundaries beneath the surface of a blasted rock pile before excavation. A method has been developed and tested to accurately measure the direction and magnitude of subsurface blast movement. This technique uses a cesium vapour gradiometer and a real-time, differentially corrected GPS system to locate pre- and post-blast position of magnetically enhanced target objects placed within blastholes inside a bench. The procedure developed does not require the blasted rock to be disturbed, and the movement information is available within a sufficient time to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m, with the overall accuracy being measured as ±1 m (horizontally) and ± 1.2 m (vertically). IntroductionOre dilution is a critical concern for many mining operations. In some instances, it may be the cause of considerable mineral loss. Where the mineralization is finely grained, sedimentary and disseminated in nature, and exhibits no clearly defined visual ore/waste boundary, there is a heightened possibility for ore grade dilution. In most modern open pit gold mines, it is economically desirable to minimize dilution in the production process through the practice of selective mining by defining pre-blast ore digging boundaries, called digging polygons, on the preblast bench area. The polygons’ positions are defined by sampling the production drill holes, with the resultant assay and survey data being used to estimate the areas of specified grade content within the bench. Once the ore is blasted in the bench, the pre-blast locations of these digging polygons are flagged as designated areas on the broken ore pile. The purpose is for the loader operator to be able to recognize which areas of blasted rock are to be sent to the appropriate processing facility or to the waste dump."

Jan 1, 2001

"In the present study, the reduction behavior of composite pellets comprising of iron oxide, synthetic graphite and slags were investigated in a laboratory-scale horizontal tube furnace. Two different types of slags indicating silicate base and aluminate base slags were chosen to examine the effect of slag chemistry on the reduction behavior of pellets. Slag composition of binding materials has influences on the reactions occurring in composite pellets during direct reduction. In-situ high temperature visualization approach was used to observe the slag / iron / carbon interactions at 1773K (1500°C). The off-gases were measured by means of infrared analyzer to determine the reaction rates of the pellets. Different physical appearances during the in situ reaction inferred a strong correlation between the slag composition and internal reactions. In addition, compression tests were conducted to examine physical strength of the pellets. This investigation was carried out to establish feasibility of physical property control of pellets by selecting optimum slag compositions of binding materials INTRODUCTIONCurrently, most of the iron ore mines have facilities that make an ore more usable for the blast furnace operation by improving its physical properties (e.g. pelletizing and sintering). However, during the process, a large amount of fuel is supplied to indurate materials which consequently deteriorate energy efficiency and produce more CO2 emission. Along with increased interests, direct reduced iron (DRI) making process; simply without coke oven or sintering process, has opened the era of clean and environmental friendly iron making process. While some of the established DRI technologies such as Midrex and HYL were restricted to certain locations where natural gas is abundant, coal based technologies using Rotary Hearth Furnace (RHF) such as FASMET and ITmk3 have been developed with regardless of expensive fuel deposit. In addition to the direct use of pulverized non coking coal and fine iron ore, RHF process also has advantages of utilizing waste materials such as EAF dust, biomass and recycled plastics. Nevertheless, there are still many challenges in the coal utilizing technologies as the unprocessed coal and the waste materials contain huge volatiles and ashes. Although recent investigations on volatiles in a RHF process (Sohn and Fruehan, 2005, 2006) have indicated the benefits of coal in terms of iron oxide reduction and have shown feasibility of multi-layer process, carbon composite pellets still have disadvantages because of its weak mechanical bonding strength. As the mixed system with carbon and oxides generates intermediate gases (e.g. CO and CO2) between solid particles, it is difficult to keep its physical state without the help of binding materials. In this reason, industries have been tried to use various binding materials such as bentonite, kaolinite and Portland cement. However, they are still struggling to find out new materials that provide not only sufficient mechanical strength but also metallurgical properties, such as porosity, reducibility and swelling throughout the reduction reaction. Recently, Canadian researchers (Aota et al, 2006) observed enhanced mechanical strength of pellets by using high alumina cement as a binder and concluded that the method could be used to recycle EAF dust as well, but in depth mechanism of reinforced strength has not been concerned. Most of the ashes coming from binders formulate certain type of slag during the reduction process due to its incombustibility. Thus, observation and regulation of slag property is an essential for the control of carbon composite pellet. Yet, only a little thermodynamic consideration from the perspective of slag chemistry has been adapted in the iron and steel making industries as ash has been easily ignored for its tiny proportion. In this study, effect of CaO-SiO2- Al2O3 slag system on the reduction of iron oxide was investigated in terms of"

Jan 1, 2012

By J. Clark

Erosion control during the mining cycle can be more effectively planned using Erosion and Sedimentation Control Plans (ESCPs). This raises the issue of who should develop an Erosion and Sedimentation Control Plan Guidance document (ESCPG) to standardize the content of ESCPs. A search for ESCPG documents in Canada revealed no examples for mine sites. In the U.S. there are a number of regulatory authorities who developed such documents for mine sites, including EPA. An ESCPG is expected to result in: (a) plans will be more standardized (b) more clarity and efficiency for those generating ESCPs; (c) assisting regulators tasked with reviewing/approving ESCPs; (d) providing guidance for the mine effluent permitting process relative to sediment control; (e) providing a basis for developing and including ESCPs in the Environmental Assessment (EA) phase and the mine economic assessment; (f) applying and optimizing ESCPs above the ?watersheds? of sediment ponds; (g) utilizing the ESCPG document for ?exploration? sites; (h) lowering the risk of adversely impacting water quality downstream of mining activities; (i) providing a methodology for determining the need for sedimentation pond(s) during the construction and production phases; and (j) providing a clear environmental sustainability message relative to sediment control if the mining industry takes the lead in developing an ESCPG. ESCPs will proactively create increased administrative (regulatory) efficiency in the EA and sub-EA reviews relative to erosion control and sediment release from mine sites. This also assists the new initiative in BC, One Project, One Process (OPOP) and synchronous permitting (a variation of concurrent permitting): as an example, enhanced erosion control planning at the EA phase then allows the synchronous permitting initiative to proceed efficiently, particularly for the mine permit (Ministry of Energy, Mines and Natural Gas) and effluent permit (Ministry of Environment). Approximately twenty more management plans (e.g. ARD/ML, explosive management, emergency response, hazardous waste, sediment pond operation, environmental effects, environmental sampling, etc.) may also be entered into the EA process to create increased efficiency, and then feed into the synchronous permitting effort. The BC OPOP initiative also adds support to the Canadian Federal ?One Project, One Review Process? approach. The ESCP and a sediment pond management plan will also address the Canadian Metal Mining Effluent Regulations requirement for all discharges from mine sites to meet a grab sample of 30 mg/L Total Suspended Solids.

Aug 1, 2013

By M. L. Trépanier

"Engineering and technical services are supplied by the Engineering Department, located at Thetford Mines, Quebec, approximately 60 miles southwest of Quebec City. The department serves the three operating mines in the Thetford area, the Asbestos Hill mine at Putuniq, Nouveau Quebec, and the Nordenham plant at Nordenham, West Germany. The Engineering Department is responsible for supplying the following services. 1. Administration and coordination of capital projects. 2. Engineering, design and drafting services for in-plant changes or improvements. 3. Preparation of geological plans for mine planning and ore reserves determinations. 4. Short-, medium- and long-term mining plans. 5. Rock mechanics studies and monitoring. 6. Grade control monitoring. 7. Environmental control engineering and construction. Details of the organization and services rendered will be the basis of the paper."

Jan 1, 1976

By M. J. Scoble, H. L. Francis, D. F. Salter, G. R. Baiden

Intelligent ore delineation refers to the ability reliably to characterize the geological setting of a mineralized body and its grade distribution. This necessitates using all available geological information in a timely and efficient manner, such that effective geological control is achieved. The importance of geological control is paramount to improving the efficiency and competitiveness of underground mines. As a result, the development of new geosensing tools designed to provide more reliable and timely information should be a priority. However, as the sensing tools advance then so, too, must the decision support system in order to allow the full benefits of these tools to be achieved. One potential system considered able to provide this architecture is ’true 3D-GIS’ (Geographical Information System). GIS promises to provide a seamless data flow and to connect information currently unavailable to the underground mine operations by bringing together previously disparate and spatial data sets in a visually effective and timely way. This paper considers the potential revolution GIS offers over the flow and use of data in mining by focusing on the integration of geosensing data and GIS to facilitate intelligent ore delineation.

Jan 1, 2000

By L. M. Lowe, D. B. Chambers, D. G. Feasby

"Potentially economic deposits of rare earth elements (REE) often contain elevated levels of naturally occurring radioactive materials (NORM), primarily thorium and uranium and their associated radioactive decay products. The concentrations of NORM usually exceed typical background levels of natural radioactivity, sometimes by factors of ten or more, and can be of concern relative to occupational radiation protection and the management and disposal of REE mineral processing and metallurgical wastes. This paper provides a summary of the radiological issues normally encountered in the REE concentrate production industry. In addition to an introduction to background radiation and radioactivity, including the thorium and uranium radioactive decay series, radiation levels expected to be encountered in REE concentrate production are outlined. The occupational, environmental and regulatory aspects of REE production related to NORM, including radiation dose limits, radioactive waste disposal guidelines, and threshold VALUES (for the application of transport regulations, are presented.INTRODUCTIONConcurrent with the increasing demand for new sources of rare earth elements (REE) to meet modern industrial needs, there is also an increasing awareness of the radioactivity associated with the REE ores and resources. This is an especially important consideration in addressing questions from the public and local communities who are often concerned about “radiation” and “radioactivity”. Public concern is heightened by reference to legacy issues that arose during times of less regulatory oversight; as well, the benefits of modern technologies, practices and regulation are overlooked. Such concerns are also often inflamed by unfounded claims by non-governmental organizations (NGO’s). Thus, it is important that all concerned have a full understanding of just what the potential risks from radiation associated with REE are, or are not. This paper provides an overview of the sources of radioactivity, the potential implications of radiation and radioactivity in the REE industry, and a brief discussion of established and reliable methods of managing exposure to radiation and radioactivity."

Jan 1, 2012

By Redhead Robert J.

"In 1991, the Canadian Council of Ministers for the Environment (CCME) charged its Waste Management Task Group with developing a nationally coordinated strategy to measure, monitor, and achieve the objective of decreasing the generation of waste (solid and hazardous) by50% from 1988 levels by the year 2000.With the encouragement of the CCME, which viewed hazardous waste as largely an industry problem, a committee, the “Industry Action Group”, representing eleven industry trade associations with a strong interest and involvement in hazardous waste was recruited.The Municipality of Markham, Ontario was also recruited (Appendix 1)."

Jan 1, 1996