Search Documents

By R. A. Sudisman, T. Yamabe, M. Osada

"Geological material can be subjected to some different loading conditions, mainly due to three inter-related physical processes which are mechanical, thermal, and hydrological. Freezing and thawing process of rock that occurs in sub-zero temperature condition may contain some or all those three physical processes depended on its initial condition. Those inter-related physical processes may lead the ground into failures. Therefore, understanding the physical properties such as deformation process of geological material under freezing and thawing condition is required for the artificial ground freezing projects and engineering construction activity in the natural cold region.In order to study the strain characteristic of rocks during freezing and thawing process, a series of freezing and thawing experiments of core samples of three different rock types and mortar has been conducted under varying temperature from -20 °C to +20 °C. Four core sample types are Sandstone, Granite, Tuff, and Mortar with 50 mm diameter and 50 mm height, which were naturally dried before the freezing-thawing experiment. Freezing-thawing experiment was conducted by submerging the vinyl covered core samples into a temperature-controlled liquid coolant box. Firstly, temperature of liquid (brine solution) was set at -20 °C so that the temperature of subjected sample was decreasing to as low as -20 °C. And then the temperature of brine was returning to initial room temperature after the coolant system was stopped. Strain gauge and thermo couple were attached on the core’s perimeter to measure strains and temperature changes.Sandstone and Mortar samples show relatively similar results than other two samples. Both presents linearly shrink with the temperature decrease and expand almost to its initial condition with the temperature increase. Granite shows less-linear strain-temperature relationship during thawing process, while the Tuff sample shows abrupt strain increase during thawing process on the temperature higher than +10 °C. Thermal expansion value of each rock types were obtained by fitting the major strain-temperature relationship on -19 °C to +10 °C temperature range. Overall, anisotropic deformation was observed on the entire samples and possible mechanisms for each hysteresis characteristic are discussed, which need to be confirmed by further experiments."

Jan 1, 2015

By W. R. Horn

"WHAT I PROPOSE TO DO is to review or report very briefly and generally on the most important subject areas of environmental concern within the mining industry and to indicate the progress being made. First, however, it seems to me both appropriate and necessary to refer to what I said in an address to the CIM Annual Western Meeting, in November 1971, in Vancouver. At that time, I tried to convey: that the awareness and alertness of this far-flung and diversified industry was sharply on the up-swing; that the knowledge of helpful technology for the abatement of pollution by water and solids was significantly increasing; that most mines were doing something about it; that many had already achieved a recycling of process water to a really significant extent; that progress was being made - though not without considerable difficulty - on the large-scale neutralization and subsequent chemical treatment of acid- and metals-bearing waters; that increasing work was being done by individual mining companies on methods for the vegetation of completed tailings impoundments; and that it had been possible to develop a meaningful estimate of the amount of money to be spent by the industry on environmental control measures during the period 1971-75 (as much as $500,- 000,000 ) . Reference was also made at that time to the constructive work in hand toward the fixation, elimination or dispersion of sulphur from smelters and to the considerable attention which was being given by the indust(y itself toward in-plant problems, e.g., dust and noise. Finally, note was taken of the fact that the inclusion of environmental control costs in the pre-operational financial provisions of new mining operations is now established practice."

Jan 1, 1973

By G. Reuben Yourt

THIS paper is chiefly a description of the improvements in dust control chat have been brought about in the assay office grinding room at Wright-Hargreaves. The fume exhaust systems are briefly included because they also are important to the health of the employees. There are three chief factors which determine the efficiency of a dust control system: First, the amount of time and thought spent in designing it. Second, how close! y it is kept up to date with the growth of the plant-a system that is adequate for the number of machines operating when it is installed may fall short of fulfilling its purpose as the plant expands. Third, unless someone is held directly responsible, a system is likely to get out of repair and gradually lose its efficiency-this can easily be detected by regular dust surveys. In designing the present system at Wright-Hargreaves, the object kept in mind was to reduce the dust concentration of all operations to a safe limit, chat is, well under 300 particles per cubic centimecer of air. By doing this, a condition would be attained chat would make it possible to discontinue the use of respirators, which at best are not very comfortable and do not remove all of the hazardous fine-dust particles.

Jan 1, 1941

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By Jiuhua Xu, Yuling Xie, Fenglei Bie, Neng Jiang

"Abstract - The Xiaoqingling Mt. area is one of the most productive gold districts in China. The gold-bearing quartz veins are controlled by a series of east-west shear zones within the Archean Taihua Group, and related to the late Yanshanian (Cretaceous) granite. The major metallic minerals are native gold, electrum, pyrite, galena, chalcopyrite and sphalerite, with gangue minerals dominated by quartz, sericite, ankerite, and calcite. The host rocks are mainly amphibolite, plagioclase gneiss, and migmatites. Principal alteration is sericitization, silicification, pyritization, and carbonization.There are four generations of hydrothermal quartz in altered rocks of gold deposits. The earliest generation of quartz, (Q1), occurs in altered amphibolite gneiss and migmatite, and typically contains fluid inclusions with halite crystals (type A) and two phases, (L+V), of fluid inclusions (type B). The salinities of type A inclusions are 32 wt% to 52 wt%, with dissolution temperatures of halite crystals being from 155°C to 465°C. The second generation of quartz, (Q2), occurs as a fine-grained aggregate associated with sericite, and has small (less than 3 µm) type B inclusions. The third generation of quartz, (Q3), occurs in mylonitic, intensively altered rocks and specially beresite (a type of rock composed of quartz, sericite, and pyrite) near the veins, and contains large amounts of CO2-rich fluid inclusions (type C-fluid inclusions with liquid CO2 and type D-fluid inclusion with high density CO2). The CO2 contents of type C range from 72.6 to 87.4 mol% in gas phases, and 35.7 to 68.3 mol% in liquid phases, based on Laser Raman analysis. The homogenization temperatures of fluid inclusion type A and C are from 215°C to 380°C, and from 210°C to 325°C, respectively. The minimum trapping pressure of fluid inclusions is estimated as 80 MPa to 170 MPa for type A, and from 57 MPa to 190 MPa for type C, which approximate to those of fluid inclusions in vein quartz.The ?18O of quartz are from 10.4‰ to 11.0‰ for Q3 of altered rocks, and from 10.7‰ to 12.8‰ for stage I quartz. The calculated ?18O of fluid inclusions varies from -1.3‰ to 6.0‰. The ?D of fluid inclusions ranges from -67‰ to -59‰ and from -81‰ to -48 ‰, respectively. It is concluded that the water in the hydrothermal fluids both reacting with wallrocks and precipitating orebodies could have been mainly of magmatic and/or metamorphic nature. However, local meteoric water might have been important in late mineralization, because of a distinct oxygen-shift toward the meteoric water. The ?34S values for pyrite of the ores range from -7.1‰ to +7.1‰, with an average of +2.9‰. Those of other sulfides (chalcopyrite, galena, and sphalerite, range from -12.5‰ to 8.3‰. The ratios of lead isotopes for galena of the ores are: 17.06 to 17.31 (206Pb/204Pb), 15.43 to 15.74 (207Pb/204Pb) and 37.58 to 38.45 (208Pb/204Pb). In summary, ore-forming fluids in the Wenyu-Dongchuang gold deposits may have originated from a mantle and/or lower crust source, and ore materials were derived from the Precambrian basement, the Taihua Group."

Jan 1, 1998

By M. Silver, R. H. McCorkell

The effects of covering materials on radon emanations from uranium mine mill tailings were investigated. Granular materials with air in the spaces allow radon to pass freely. Moist covers of compost or soil decrease radon emanation from tailings. Water-saturated covers were more effective, and freezing the tailings with these covers further decreased radon escape. Water itself is a poor radon barrier probably due to circulation. Plants had no effect on radon emanation through soil. Although radon diffusion through water-saturated powders appears to be very slow and inefficient, about 25% of the radon escaping from the grains in water-saturated tailings diffuse to the surface and emanate when no cover is present. The radon escaping from tailings through covers of water-saturated compost or soil is no more than could be accounted for by radon produced in the covers themselves.

Jan 1, 1987

By Matthew Janes

Advantages: Clean samples Low sample disturbance Very low spoil Versatile Fast Penetrates all formations Resonant Drill 100 or 150 kW Self tuning to resonance Rotation to 100 rpm Increased depth in dense soil Increased productivity Reduce water use Reduce casing plugging

May 1, 2013

By J. K. Szymanski

"RÉSUMÉPour maintenir de bonnes performances technique et économique dans l’exploitation par chambres vides (open stope) il est primordial d’assurer un contrôle efficace des limites réelles des chantiers d’abattage. C’est pour cette raison que, de plus en plus souvent, les opérateurs miniers utilisent un dispositif de laser (Cavity Monitoring System: CMS) qui permet de mesurer les dimensions réelles de chantiers en vue de calculer principalement la dilution et les pertes du minerai ainsi que d’autres paramètres. Malheureusement, il n’existe présentement aucune méthodologie commune, qui permettrait d’interpréter ces résultats selon les mêmes critères pour faciliter d’évaluations juste et précise de la réalisation par rapport à la planification en vue d’en apporter de corrections, dans les différentes opérations minières, si nécessaire. Dans la première partie du présent article on discute les principales séquences d’exploitation utilisées dans l’extraction par chambres vides. Par la suite, à l’aide des sections transversales et longitudinales on illustre toutes les phases des travaux miniers. Ceci en vue de permettre au lecteur de comprendre mieux c’est qui peut se passer effectivement dans les chantiers d’abattage. Par après on donne les définitions générales de principaux facteurs de performance technique. Finalement, l’exemple numérique, élaboré à partir des résultats de l’arpentage au laser effectué par la mine Bousquet 2 dans un chantier d’abattage, donne les détails concernant les définitions ainsi que les valeurs de nombreux facteurs de performance technique, qui pourraient être utilisés, par après, par les opérateurs miniers dans le suivi de leurs exploitations souterraines."

Jan 1, 1997

By M. S. Badollet

"The study of the physical properties of asbestos minerals requires a careful isolation of the fiber from the wall rock and, at a later stage, a comparison of these physical properties with those of fibers that have passed through the milling and beneficiation processes.The effects of mineral impurities, loss of fiber length and the formation of extreme fines (asbestic and/or associated minerals) often show up in the formation of special asbestos products as well as in the commercial production of asbestos papers, mill-boards, asbestos cement products, plastics and insulation materials, and in the filtration of blood plasma and wines.Numerous test methods have been developed in Canada and in England for use in the asbestos industry. Special treatments of asbestos fibers have been used to improve their physical and chemical properties and to eliminate impurities.Numerous problems connected with the use of asbestos fibers are discussed, such as the effects of asbestos on filtration, surface area, surface treatments using organic or inorganic materials, the surface charge on the fiber, the presence of magnetite and air pollution elimination. Biological studies on finely ground asbestos, when dispersed in 0.9 per cent sodium chloride solution and then sterilized and injected into hamsters, show that by reducing the dose, the tissue damage can be largely avoided. In these experiments, Arizona asbestos fibers were carefully extracted from the wall rock, finely ground, and examined chemically and micros-copically for any mineral impurities that might be present so that any effect on the hamsters would be directly due to the presence of the asbestos. The harsh Arizona fiber induced more extensive tissue response than the soft fiber when tested in hamsters."

Jan 1, 1969

By C. W. Jr. Waterman

INTRODUCTION MY SUBJECT is one which would require several speakers and many hours of time for adequate presentation in all its many facets. Because of the widely varying market requirements and coal seams mined, the coal industry of the United States bas of necessity employed many types of preparation facilities to satisfy its needs. Predominance of Baum-type jigs, however, bas marked the mechanical cleaning installations since the early thirties, and these machines continue to hold the lead. CLEANING As a matter of record we find that, at the end of 1948, we had 480 mechanical cleaning plants in operation. Of these, 19 used air cleaners only,?400 used water washers only, . and 61 used dry and wet washers in combination . Due to the increased use of spray water underground on cutting and mechanical mining equipment, there has in recent years been a marked downward trend in dry cleaning installations. In fact, the moisture in dry-cleaned fines has been increased to such an extent by spraying that recent dry cleaning installations have incorporated thermal drying ahead of the dry cleaning units in an effort to overcome the varying and increasingly higher moisture percentages in their raw coal feeds. While on the subject of dry cleaning, it might be well to bring to your attention one of our most recent developments in this art. I refer to the McNally-Brusset vacuum jig.

Jan 1, 1951

By H. W. Kasaini, E. Bourricaudy, T. Larochelle

Rare Element Resources Inc., a U.S. based company, has developed a three-stage process for producing a +98% mixed REO powder from hard rock feedstock (-48 mesh, 2.9-4.8% REO) consisting of bastnaesite and ancylite minerals. Firstly, the whole ore is digested in chloride media at low temperature in counter-current flow mode. Secondly, the rare earths (REEs) are selectively precipitated as oxalates directly from an impure pregnant leach solution (PLS). Finally, significant amounts of free acid and water are recovered from the REE-depleted filtrate and subsequently recycled within the process. Excess heat from the oxalate calcination process is captured and reused in the plant. Due to the low leach temperature (45 ºC) and moderate acid dosage (240-297 kg/t, HCl), rare earth oxides (REOs) are preferentially leached out of fine solids leaving most of the base metals (Ba, Fe, and Al ) in the residue. Selective recovery of REEs from the PLS is achieved by mixing dilute oxalic acid (33% H2C2O4) and PLS at elevated temperature (85-95 ºC). The REEs plus thorium are precipitated as oxalates (REE2 (C2O4).xH2O) while the base metals are left behind in the barren filtrate. Multiple batch and pilot test results have confirmed that 50-80% of the oxalic acid can be recovered from the REE-depleted PLS through low-temperature crystallization (10-15 ºC). Typical leach efficiencies of critical rare earths at 45 ºC range from 85-99% (average 93%) while oxalate precipitation at high temperature increases the crystal size of RE oxalates (>450 microns, d80) thereby improving filtration. The economic benefits of this process include elimination of flotation and magnetic separation Capex and driving hydrometallurgical Opex down to $6- 7/kg, REO produced. As part of a comprehensive risk mitigation strategy, Rare Element Resources Inc has operated multiple pilot plants at SGS in Lakefield, Ontario, Canada to optimize counter-current leaching (CCL), REE oxalate precipitation (OXP), and thorium removal circuits. This paper presents pilot testing data from CCL and REE OXP circuits.

Jan 1, 2016

By W G. Forbes

SOME 20 years ago, upon finishing second year at the University of Manitoba, I was faced with the choice of whether I wanted to be a geologist or a chemist. Accordingly, I sought out Professor Brownell, Head of the Department of Geology, to ask him what a geologist did. His reply contained the statement that following graduation one went out into the field in northern Canada for 5 to 15 years to reduce to practice what had been learned at university. To a young man, very socially conscious, even one year, let alone 5 to 10, in a small mining community sounded like being banished to a monastery in the Himalayas and thus I turned to chemistry. Moving to the present, last month I asked a geologist, and then a mining engineer, what does the fresh graduate in their field do these days? The reply was: usually serve an apprenticeship for an indeterminate period either underground or in the field learning the job.

Jan 1, 1965

The use of QemSCAN in providing mineralogical input to detailed ore and product characterization has proved of immense value in recent years. In this paper, a brief review of selected Cu-case studies is presented to demonstrate the versatility of automated, quantitative mineralogy by QemSCAN. This versatility ranges from measurement and analysis strategies through to data processing and presentation. As a rapid diagnostic service, it is common to find that only grain size, the degrees of liberation and/or ore mineral modal mineralogy are of interest. By contrast, the detail afforded by the simultaneous determination of both gangue and ore minerals can alert mineral engineers to fatal flaws and attributes deleterious to processing that are directly a function of silicate and other gangue mineralogy. Examples of the latter effects include the influence of micaceous minerals and acid consuming species, while the former include fluorine minerals, which can provide both processing and environmental challenges.

Jan 1, 2007

By F. E. Senftle

Introduction The usual laboratory methods of uranium analysis are either tedious, time-consuming chemical procedures or elaborate physical methods requiring sensitive equipment. There is thus an urgent need for a method of estimating the uranium content of ore samples by approximate analysis in the field. When a new property is being developed, it is desirable to know, with the least possible delay, the uranium content of channel samples in order to guide the diamond drilling and digging operations. Prospectors, too, require approximate analyses of their hand specimens to evaluate their discoveries. To satisfy the demand for these types of analyses, several field procedures have been tried. Two general plans can be followed. One is fast but will yield only a rough estimate. The other is slightly longer but, if done carefully, will give an assay probably within 10 per cent of the true value. For field operation it is necessary to strip the more accurate laboratory methods of analysis of all refinements because of the limited equipment and skilled techniques at hand. Most of the corrections normally applied, with the exception of that for equilibrium, will not alter the gross analysis to any appreciable extent. When uranium atoms in pitchblende disintegrate, they break down into other radioactive elements, and eventually the number of elements being formed is equal to the number breaking down. The ore is then said to be in equilibrium. Certain geological processes, however, such as leaching, may selectively remove some of these elements and hence reduce the radioactivity of the ore sample. The ore is then said to be out of equilibrium. The field analysis may then be in error by as much as 50 per cent since the apparatus is calibrated with standards that are in equilibrium. However, such a large error due to loss of equilibrium is the exception, and in most cases uncorrected field types of analyr.is are justified.

Jan 1, 1949

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

By K. Mayhew, R. Bruce, A. Heidel, G. P. Demopoulos

"Teck and Aurubis are working together to commercialize a technology for the processing of copper arsenic sulphide concentrates that is economic and sustainable with regards to the environment and community. The pressure hydrometallurgical approach is a desirable option as mineral extraction and arsenic fixation can take place in a single autoclave vessel. A test work program was carried out where a range of copper concentrates with varying arsenic grades was processed under CESL leach conditions. This paper discusses the stability character (in terms of arsenic) of the resulting residues and their mineralogy. The basic ferric arsenate sulphate phase (BFAS; otherwise known as type 2) was identified as the main arsenic carrier. All CESL residues demonstrated high stability (<1 mg/L As) through a range of aggressive (pH and ORP) environmental leach conditions.INTRODUCTIONArsenic deportment and control in the copper industry needs an integrated approach involving each stage of the value chain, i.e. exploration, mine operation, refining process and mine closure. Teck Resources Limited (Teck), Canada’s largest diversified mining company and Aurubis, Europe’s largest copper producer, have formed a partnership to advance the application of CESL copper-gold technology for the development of high arsenic bearing copper resources (Bruce et al., 2011).Among the options for arsenic control in the metallurgical treatment of copper concentrates is the precipitation of ferric arsenate, which is widely accepted as the most suitable method for stabilizing arsenic (Ferron and Wang, 2003). The pressure hydrometallurgical approach to processing arsenic bearing copper concentrates is a favorable option as mineral extraction and arsenic fixation can take place in a single autoclave vessel. Under CESL pressure leaching conditions (150 °C, 1380 kPa) high copper extraction and arsenic (V) fixation is possible.Within the pressure leach autoclave, arsenate and ferric iron react to form scorodite type phases. The precipitate formed under CESL conditions is dependent on the Fe (III) /As (V) ratio and the tenor of cations and anions, particularly excess sulphate (Gomez et al., 2011a). Previous studies on CESL residues have found arsenic to be present as crystalline scorodite (FeAsO4.2H2O) (Bruce et al., 2011), basic ferric arsenate sulphate (BFAS: Fe(AsO4)1-x(SO4)x(OH)x·(1-x)H2O, where 0.3<x<0.7), and/or arsenate adsorbed on to hematite (Gomez et al. 2011b). Although not a focus of previous work, scorodite was the predominant precipitate formed when the concentrate Fe/As was <1.5 (Mayhew et al., 2010), and BFAS was the predominant precipitate when the concentrate Fe/As was >10 (Gomez et al. 2011b)."

Jan 1, 2012

By P. F. Berry

X-ray fluorescence analytical techniques are fairly well established in the mining and metallurgical industries. In recent years, instruments utilizing radioactive isotopes have been developed which, owing to their more compact size, greater reliability and independence of substantial power supplies, are often preferred to X-ray tube installations. Analyses can now readily be carried out in the field, on the factory floor and in otherwise difficult locations. This paper describes many examples of radioisotope X-ray fluorescence for the analysis of metallic minerals, finished metals and alloys and also for the continuous measurement of metallic coatings, such as tin and zinc, on steel. Radiation scatter techniques are also described for certain analyses and for thickness and density measurements.

Jan 1, 1967

By P. W. Billwiller

Abstract The Britannia Mining and Smelting Company, Limited, have replaced diamond drills with percussion drills and tungsten: carbide bits for most of their blast hole drilling operations and have thereby reduced ore breaking costs. Two-inch Carset bits .are used, with one-inch hexagonal Atlas Chippewa alloy steel in 3-foot .and 6-foot lengths. Locally made couplings of Atlas SPS 245 alloy steel connect the rods. The machines used are 31½-inch automatic leyners with lugged or anvil block chucks. For drilling holes below the horizontal, the lugged machines with special adapter rods made from 114- inch solid round Atlas SPS 245 are required. These rods are lugged at one end and a water hole is drilled for six inches into the other end. Over this rod is placed a water swivel which permits the water or air to be sent directly into the steel. A decreased cost per foot, increased footage per shift, and the use of standard equipment and crews are some of the main advantages of tungsten carbide drilling over diamond drilling. Introduction Long-hole drilling with percussion drills and sectional steel was introduced in several American mines some twenty-five years ago. It did not prove very successful, however, because the rapid gauge loss in steel bits necessitated the use of very large starter bits. This in turn rapidly fatigued the straight carbon-steel then in use, made it difficult to maintain the couplings, and resulted in a slow drilling rate. The introduction of the tungsten carbide insert bit and alloy drill still has changed this picture and opened real possibilities for the application of percussion drills to blast-hole drilling. If this type of bit had been perfected ten years ago, much of the research work and experimenting done to apply diamond drills to ore breaking would have gone toward developing the application of the tungsten carbide bit to this problem.

Jan 1, 1950

By C. H. Bucknam

Net carbonate value (NCV) characterization methods for acid generation potential measurement originated from studies on the Carlin Trend during the 1990&apos;s and have been subsequently standardized through cooperation of the Acid Drainage Technology Initiative Metal Mining Sector and the American Society of Testing and Materials International. The paper describes the evolution and standardization of the NCV methods, the importance of mineralogy in interpreting the results and application of the methods to implementation of the Global Acid Rock Drainage (GARD) Guide.

Jan 1, 2011

By Graham Walker

A new Code of Practice for the brake performance of off -highway vehicles was established in Alberta in 1976. Vehicles loaded to gross vehicle weight must be capable of stopping with mechanical brakes five times in quick succession on a grade of 10 per cent from a speed of 28 miles per hour. Comparative trials of various brake systems have been carried out and some combinations capable of meeting the Code are identified. Some problem areas in truck braking are reviewed and potential developments indicated.

Jan 1, 1977