Search Documents

By R. W. Thompkins

The two largest contributors to silicosis in machine men are dust from drilling and dust from blasting. With the advent of the shatter-cut method of blasting, the evils of blasting dust were greatly reduced. The problem of dust from drilling has been attacked from two different angles: (1) The adoption of dustless frontheads or enlarged water tubes, both of which have proved capable of reducing dust concentrations; and (2) The adoption of better ventilation. Many operators are loath to adopt dustless frontheads or enlarged water tubes on Leyner drills because of the increased repair costs on drills, and also because it has been found difficult to enforce 'the proper usage of dustless machines: for example, workmen sometimes plug the vents in the fronthead.

Jan 1, 1943

By Jae-Chun Lee, Rajiv Ranjan Srivastava, Min-seuk Kim, Byung-Su Kim

Recycling of spent hydrotreating catalysts (HTC) can potentially contribute towards the sustainable extraction of metal values. Treating such materials by hydrometallurgical methods to separate metals from the leach liquor of either acid/alkali media is a major step. In the present study, separation of molybdenum from HCl leach liquor of spent NiMo type HTC has been investigated by applying solvent extraction using Cyanex-923. For this, the chloride solution containing 973 mg/L Mo, 254 mg/L Ni and 1634 mg/L Al was taken as the aqueous feed. The parameters including contact time, concentration of the extractant, acid and chloride, and phase ratio were varied to investigate their effect on the extraction efficiency. The McCabe-Thiele plot suggests that > 99% Mo-loading using a 2-stage extraction process. From the molybdenum depleted solution, nickel was selectively extracted by Cyanex-301 leaving Al in the raffinate.

Jan 1, 2014

By Ahmad Ghahreman, Lin Li

"In this study, the Fe(II)/Fe(III) redox reaction kinetics on the surface of pyrite, have been investigated in a 0.5 mol L-1 sulfuric acid solution for a temperature range of 22 to 65°C. Based on mixed potential theory, chronoamperometry is introduced to study the Fe(II)/Fe(III) kinetics by subtracting the current density of pyrite oxidation in an iron-free acidic solution from that in an iron-containing solution at the same applied polarized potential. Tafel behavior was established by this method to analyze the kinetics of the Fe(II)/Fe(III) redox reactions. The results showed that exchange current densities increased slightly with temperature, however remained on the order of 10-5 A cm-2. The activation energy for Fe(II) oxidation and Fe(III) reduction on the pyrite surfaces was calculated to be 102.0 and 32.7 kJ mol-1, respectively. Anodic transfer coefficients also increased, from 0.24 to 0.39, with increasing temperature, which indicates a weakened n-type semiconductor property at higher temperatures. Electrochemical impedance spectroscopy measurements have indicated that at lower anodic over potentials the charge transfer is the rate determining step of pyrite oxidative dissolution in sulfuric acid solution. In the presence of Fe ions, the major contribution of the total current density comes from the Fe(II)/Fe(III) redox reaction. INTRODUCTION Pyrite, an abundant sulfides mineral in the nature, is commonly considered a valueless gangue mineral frequently associated with other valuable sulfide minerals such as chalcopyrite, or metals such as gold, or coal (Lin & Say, 1999). Pyrite oxidation has been the subject of extensive research in view of gold metallurgy, as oxidation of pyrite is the initial step to break down the pyrite lattice and expose the encapsulated fine gold particles (Gasparrini, 1983). Fe(III) ion and dissolved oxygen (DO) have generally been considered as the two most important oxidants with respect to pyrite oxidation, having been studied extensively in previous research (Zheng, Allen, & Bautista, 1986; King Jr & Lewis, 1980). The process of pyrite oxidation can be viewed as a series of reactions amongst pyrite, ferrous, ferric and oxygen in which pyrite is initially oxidized by the dissolved oxygen in water forming ferrous (Eq. 1), and then the ferrous also is oxidized by he dissolved oxygen to form ferric (Eq. 2). The ferric, produced by reaction 2, then could potentially oxidize pyrite (Eq. 3) and convert to ferrous."

Jan 1, 2017

By D. Perednis

Fuel cells with thin samaria-doped ceria (SDC) electrolyte films deposited onto an anode support using spray pyrolysis were fabricated. The SDC films were deposited onto porous NiO-YSZ substrates at deposition temperatures between 400°C and 450°C. The influence of process parameters such as deposition temperature, flow rate, type of salt and salt concentration on the quality of the film was studied. A smooth dense film was successfully deposited using the precursor cerium ammonium nitrate and samarium nitrate dissolved in butyl carbitol (33.3 vol.%), 2-methoxy-l-propanol (33.3 vol.%), and ethanol (33.3 vol.%) solvent mixture. A deposition rate of 125 nm/h was achieved.

Jan 1, 2005

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By Donald L. Mordell

Introduction A very large part of the world's fuel resources are in solid form, as various grades of ?coal, but an increasing proportion of fuel demands on this Continent and else-where are having to be met by liquid fuels. Convenience and, in many cases, cost weigh heavily in favour of the liquid: fuels, and there are many fuel burning applications where the use of coal would be impractical, such as for automotive or air transport. By extrapolating the present trends one might conclude that, in future years in Canada and the United States, coal will be used only in a few power stations close to coal fields. If such a state of affairs should arise, it will obviously prove embarrassing to those accustomed to make their livelihood from the winning and marketing of coal, but it is perhaps not so obvious that it must also prove an embarrassment to the nation. The major reasons for this are two in number. Firstly, if present coal production is to be replaced by oil production, a large capital expenditure is necessary, which must inevitably be paid by the consumer; and secondly, in times of emergency, large amounts of oil fuels are required for military purposes which cannot be achieved with solid fuels. It is obviously unwise, therefore, to discontinue the use of coal for those non-military jobs that it can do. If we examine the major fuel markets we find that there are three: Domestic heating Steam generation Transport by air, sea, and land For domestic heating, the extreme convenience of oil, in spite of its greater cost, has captured much of the coal market.

Jan 1, 1952

By M. J. Bunyard, I. Mullany

"The pressures on mine operators are varied and constantly increasing, declining ore grades, more remote locations and increasing environmental concerns. The challenge facing the mining industry is to find new ways to process ores which are more efficient and less costly and to control them better. This requires a fundamental rethink in the way in which projects are developed, it is no longer good enough to just copy what has been done before. The process starts with the surfacing of the primary underlying constraints for the project and the establishment of new design principles to address these. The generation of new design criteria and processing options follows the well-established path of brainstorm, focus, brainstorm, refocus and economic evaluation. The aim is process intensification, doing more with less, as early as possible and better use of plant data. The methodology requires a complete geometallurgical understanding of the orebody to facilitate the evaluation of viable processing options. Examples of early stage processing considered are blast optimization and ore sorting to reject waste and reduce processing costs. Mine to mill integration, which starts with the optimization of blasting for separation, offers another way to significantly reduce operating costs and increase efficiencies.VALUE MODEL The mining industry has, over the past decade, experienced an unprecedented cycle of increased commodity prices and investments in new mining and processing capacity followed by a market collapse and fall in prices and confidence. Whilst there are now some signs of a return to investment in new capacity, the metals and mining industry is still wrestling with eroding margins and investor demand that companies achieve the full value of their assets. Metals and mining companies must work on all available levers to deflate their costs back to more manageable levels and capture the full value for their products. Levers include optimizing external spending, re-thinking make vs buy trade-offs, debottlenecking, improving availability and operating time of key equipment, more accurate and agile planning processes, value-in-use optimization, and tighter performance management. Figure 1 is a diagrammatic representation of a company’s value model. The three goals of a successful mining enterprise are social acceptance, environmental acceptance and sound financial returns to shareholders. Some of the KPI’s used to measure the success or not of achieving these goals are shown in the translation layer."

Jan 1, 2017

By Marlin E. Sandlin

NORTH-CENTRAL United States is now, and will continue to be, a natural market for Canadian crude oil. This area is a natural market for many basic reasons. There are no physical barriers along the border of our countries. This market is in dose proximity to Canadian production. This market is already joined by crude oil pipe-1,ines to numerous producing areas of Canada. The tariff barriers are reasonable. We are not handicapped by mandatory quota restrictions. There are many of us who desire lo sell Canadian crude oil in this market. Further, and what is really important, there are many of us who desire to buy Canadian crude oil for this market. It is fundamental that for crude oil to be sold in the world market, it must ?be sold at competitive prices. At the same time, it is important that such competitive price must result in a fair price for the crude oil at the we1lhead. The factors of nearness to market, cheap pipe line transportation, and reasonable United States tariffs, all tend to make ?possible a competitive market and a fair wellhead price.

Jan 1, 1958

By E. Dernedde

Cell rooms of aluminium smelters have large openings in the sidewalls and in the roof. These openings provide a high ventilation rate, which removes heat and contaminants emitted by the reduction cells and thereby ensures acceptable working conditions inside the cell room. However the large openings make the airflows through the smelter building sensitive to the wind. In this study equations for the airflow through the openings of a smelter building exposed to crosswinds were developed and verified against plant measurements. The equations were then used to estimate the airflows through a two-storeyed smelter building containing VS Soderberg cells. Wind protection by wind-covers over the sidewall openings and by upwind buildings made the airflows through the building less sensitive to the wind. Physical and mathematical modelling showed that working conditions inside the wind-protected cell room would be acceptable for crosswinds at speeds up to 16 km/h. These predictions were confirmed by measurements taken in a VS Soderberg smelter.

Jan 1, 2007

By Henry Lepp

Introduction A shaft sinking operation carried out at the Viking Yellowknife mine in the spring of 1947 presents certain features, especially as regards speed of sinking and low cost, that may be of interest to Institute members, and especially to those who are not familiar with conditions and costs in the Northwest Territories. After collaring, the inclined, two-compartment shaft was sunk 130 feet by four miners in twenty-eight days at a direct cost of only $53.19 per foot. All things considered, this is a remarkable performance, even if it does not actually establish a record. The property is at Morris lake, some forty-five miles north of Yellowknife. Formerly owned by Athona Mines (1937), Limited, it was acquired by the then newly incorporated Viking Yellowknife Gold Mines, Limited, in 1947. Surface work and diamond drilling in 1946 disclosed a number of veins and masses of quartz in a sill of diorite which lies conformably within sedimentary rocks. The sill strikes N.30°E. and dips at 70° to 85° southeast, and has a mean width of 40 feet over its explored length of 3,000 feet . Both the quartz and the diorite carry gold and are mineralized with pyrrhotite and lesser amounts of galena, sphalerite, chalcopyrite, and arsenopyrite. Of thirty-five holes drilled in the mineralized zone, the core from twenty showed visible gold. Sampling of drill cores indicated several ore shoots in the north and central parts of the sill. Assays, however, were somewhat erratic, possibly due to the fairly widespread presence of visible gold, and it was decided that the deposit could best be explored by underground sampling. Accordingly, late in 1946, plans were laid for the sinking of a shaft.

Jan 1, 1948

By Robert H. Clark

Introduction During the last twenty years, science and industry have been strenuously endeavouring to discover new sources and new kinds of liquid fuels and to work out suitable chemical methods for their production. One of the new possibilities for the production of liquid fuel on a large scale is law-temperature carbonization of various grades of coal. The use of alcohol as motor spirit, in spite of its relatively low calorific value, is being widely investigated. Its production by fermentation of sugars, its recovery from the sulphite liquors of the paper industry, its production directly from wood and also from calcium carbide, have all been considered. At present the most promising line of investigation would appear to be the further development of those technical processes which yield liquid fuels from coal; since science has shown the possibility of preparing all kinds of liquid fuels and even the complete conversion of coal into oils. The present paper will consider briefly: 1. The production of primary tar by low temperature carbonization of coal. 2. The hydrogenation of coal. 3. The synthetic processes of Dr. Franz Fischer.

Jan 1, 1928

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By Dennis Hoffmann

"Abstract - Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa , were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, Al, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/Al, Si/Fe, Fe/Mn, La/Ce and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnet­ and amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+ Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By Richard Dawson

Presentation Outline? Northeast BC Coal Fields Overview and History ?New mines and projects in development ?Design Issues for steeply dipping footwall slopes ?Design issues for angle-of-repose waste rock dumps

May 1, 2006

By A. Ghasemi

An alumina-silica coating was deposited on a nickel substrate by sol-gel process, and the structures and composition were evaluated, The sols were made from aluminium and silicon alkoxide, and an acid catalyst including HCl, To produce adherent silica coatings on nickel, various additives such as surfactant, viscose additive and drying control chemical additives were introduced to the system, and appropriate drying and firing cycles were applied after dipping in solution. The hot corrosion and oxidation resistance of the coating at different temperatures were investigated, The structure and uniformity of the coatings were examined by scanning electron microscopy (SEM), The results indicate that a uniform coating of alumina silica can be produced on a nickel substrate by optimizing the composition and process variables of the sol. Coatings can protect substrates from oxidation and hot corrosion at different temperature up to 1000°C, but is not very effective for hot-corrosion resistance at 1000°C.

Jan 1, 2005

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By C. J. Hall

This paper presents a basic motive column analysis of natural ventilation and shaft resistance, using the density depth diagram. The method makes use of tables showing the state of the air as determined by thermodynamic analysis. Several theoretical examples are given.

Jan 1, 1968

By W. A. Roliff

The renewed interest of the past few years in the Appalachian and Michigan oil provinces has not, as yet, created any marked increase in activity in Southwestern Ontario. During 1960 development drilling in-creased somewhat over 1959, but exploratory drilling decreased slightly. More attention was devoted to the deeper horizons, but lake drilling de-creased considerably. Oil production reached a new peak and gas production increased slightly. During 1960 an interesting oil and gas discovery was made in the Cambrian and gas discoveries six miles off-shore in the eastern part of Lake Erie were made in the Clinton-Cataract zone of the Silurian. This paper reviews activities during 1960, summarizes the discoveries made to-date and the pertinent exploration data relating to the prospects of the region and discusses some of the economic aspects of exploration and development. D URING the last few years there has •been a marked renewal of interest in the old petroleum

Jan 1, 1961