Search Documents

By L. Li

Backfill is increasingly used in underground mines, as it can help reduce the environmental impact from mining operations. However, the primary objective of backfilling is to provide safe working space for miners, by improving ground stability conditions. As cement is often added to the backfill, a critical issue is the determination of the required backfill strength (cohesion) due to the binder. This value is usually obtained from a solution proposed by Mitchell and co-workers, in the early 1980?s, for stopes with an exposed backfill face. This paper presents a brief review of the Mitchell et al. solution, with some of its main limitations. Some of the recently developed solutions for backfill design are then summarized and discussed.

Aug 1, 2013

By P. N. Saavedra, E. A. Salamanca

"The maintenance strategies in the mining industry are changing from operative and periodic inspection strategies to a condition-based, predictive maintenance strategy centred in vibration analysis plus complementary techniques. Condition monitoring can also help to improve availability by being able to pinpoint and diagnose problems on operating machinery at an early stage. This reduces unscheduled downtime and production losses.However, in mining, for shovels operating in transient modes, with variable load and/or speed, the FFT (Fast Fourier Transform) standard approach is not directly applicable for analysis. This work illustrates how spectral order analysis and new transforms, called time-frequency transforms (TFT), allow us to monitor the shovel when it is working. Some practical examples showing the application of these analysis techniques to occasional vibrations measured on hoist and crowd transmission of a shovel are also presented. It is shown that at present, it is possible to carry out the vibration monitoring in the mining shovel while it is working, therefore avoiding the high cost of a loss of production which can occurr in traditional monitoring, where the measurement is taken while the shovel is out of production."

Jan 1, 2002

By F. A. McLean

Given a promising claim and the required financial backing to develop it, the first problem that confronts the mine operator is usually the selection of the necessary compressed air plant. The size and type of drive are questions that naturally follow, the former being determined largely by the amount of money available and the speed with which it is desired to carry on the programme of development. The type of drive, such as electric motor, steam or oil-engine, depends on local conditions and has an important bearing on the cost of operations. ns. Few prospective mine operators are fortunate enough to locate claims within the service radius of electric power-lines, although this is more likely to happen nowadays than formerly. In the majority of cases, however, some other form of prime mover is necessary. When wood or coal are available at moderate cost, a small steam-driven plant is usually chosen. Such plants are often arranged so that they can be converted to electric-drive should future developments at any time make this desirable. Many plants of this type are installed in northern Ontario mines. When wood or coal are costly or difficult to transport, oil-engine driven mining plants have many advantages in their favor, and are now quite commonly used. Oil in some locali-ties is considerably cheaper than wood or coal, and is much easier to transport over bad roads.

Jan 1, 1924

By P. Su

Friction stir spot welding of a range of Mg-alloys is investigated (AZ91, AZ31, AM50 and AM60). The peak temperatures during friction stir spot welding of all Mg-alloys are close to their solidus temperatures. Also, the apparent material viscosity of Mg-alloy sheet is lower than that when Al-alloy sheet material is spot welded. This is important since it means that the widths of the stir zones forming during spot welding of Mg-alloy sheet are smaller than those when Al-alloy sheet is welded (when identical welding parameter settings are applied). These lower apparent viscosity values must be taken into account during numerical modeling of the Mg-alloy spot welding process. The efficiency of energy utilization is very low when Mg-alloy sheet is spot welded and is of the same order as that when fabricating Al-alloy sheet. The energy generation contributions of the rotating pin and the tool shoulder are investigated. When the spot welding operation is carried out without the application of a dwell period, the contribution made by the rotating pin vis-à-vis energy generation is around 66%. The contribution made by the tool shoulder increases to about 65% when a dwell period of four seconds is incorporated during the spot welding operation. This increase results from a longer contact time between the tool shoulder and material within the stir zone, The failure load during overlap shear testing increases when the bonded area and the energy input increase during spot welding. Sample failure initiates from unbonded regions and from discontinuities at the edge of the stir zone. The formation tendency of discontinuities is increased when Mg-Alloy sheet is spot welded because of the limited deformation characteristics of the base material at lower temperatures.

Jan 1, 2006

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By L. H. Chen, Y. C. Chen, Leo Benyamin, W. C. Chen

"To investigate the evolution of fluid-driven fracture of rock-like material subjected to borehole fluid pressure and its consequential damage with regard to post-peak stabilization, micro-seismic activities have been monitored using nondestructive technique of acoustic emission (AE) corresponding to the macro-scale complete history of loading curve by setting the hollow cylindrical external circumferential strain to be a closed-loop feedback signal during servo-fluid-driven tests. Development of a novel fluidinduced loading system injected from internal borehole as well as monitoring system were equipped such that the initiation and propagation of micro-cracks enable to analyze experimentally. By programming/controlling either injection rate or fluid pressure, synthetic sandstones with low-permeability made by cement mortar were conducted in this study. It found that both the growth of macro-crack initialized intensively as reaching the breakdown pressure and the micro-seismic activities represented by AE locations show nice agreement. The experimental results in this paper provide better understandings of fluid-driven fracture mechanism.INTRODUCTIONFluid-driven fracture is a process of generating cracks by injecting viscous fluid into solid material. Conventionally, fluid-driven fracture tests have been performed by mining industry to measure the in situ stress (Haimson & Fairhurst, 1969) and fluid-driven fracture has been employed by the petroleum industry to recover oil and gas. Additionally, the mechanism of crack growth or the extension of existing cracks is important to the evolution of volcanic dikes over distances of a few kilometers (Lister & Kerr, 1991; Rubin, 1995), crack propagation in dams (Bolzon & Cocchetti, 2003) and the disposal of radioactive waste (Sun, 1969)."

Jan 1, 2015

By Oyku Selimoglu

The key to successful mine production plan and subsequent operation is efficient mine layout design and optimization. Pit layout design and optimization allow the delineation and extraction of mineable reserves and the minimum waste subject to slope stability, economic, quality and quantity constraints. Many design and optimization software packages have been developed to aid this intensive and challenging process. These packages include VULCAN, SURPAC, DATAMINE, GEMCOM, MICROLYNX, MEDSYSTEM and MINESIGHT. These software packages are developed as integrated computer-aided systems used for database creation, survey, geological and geostatistical modeling, mine planning and production optimization and environmental modeling. In Turkey, many mining companies still plan and design mine layouts with traditional hand methods. In this study, VULCAN has been used to design and optimize the Eti-Bor A.S. Kestelek Boran Open Pit Mine in Western Turkey. The main objective is to show the company the superior advantages of mine planning software for designing and optimizing mine layouts over the traditional hand methods. Drill hole data used by the company to estimate the reserves for planning are used in this study. The ore grade varies between %1,04 B2O3 to %47,33 B2O3. The pit toe and crest strings are projected using variable batter angles and berm distances. On the north side, batter angle is 180 and berm distance is 25 meters, on the south side, batter angle is 320 and berm distance is 15 meters. In addition to that open pit bench height is 10 meter. The concepts of block modeling are applied to the Kestelek open pit mine with detailed ore grade modeling for each block. The Lerchs-Grossmann?s algorithm is used to optimize this mine based on the block model, the economic block values for each block and the underlying field constraints. The results from VULCAN were similar to the estimates by hand. The reserve estimates from VULCAN is 13,192,870 tons compared with the hand estimate of 13,200,000 tons, overburden estimates of 15,622,889 m3 compared with 15,000,000m3 obtained by hand with a stripping ratio 1.18:1 (m3:ton) from VULCAN versus 1.14:1 (m3:ton) from hand estimate. Vulcan improves the efficiency, speed and reproducibility of the planning results. It provides mining engineers, geologists and surveyors with a cost-effective modular system for assessing and planning the mine layouts. Furthermore, Vulcan?s specific modules allow efficient access and manipulation of databases, open pit mine design, block models, optimized 3D mine layouts, and more. However, for competitive business in Eastern Europe, VULCAN should improve its software support. Effective training, help desk support systems and nearby distributors with just-in-time solutions to company problems will generate competitive business for VULCAN.

May 1, 2007

By Pascal Turcotte

_ Introduction _ LaRonde _ Controlling Instability in Haulage Drifts _ Failure mechanism in drifts walls _ Failure mechanism in drifts back _ Field Behaviour of Support Elements _ The ?Hybrid Bolt? _ Conclusions

Feb 1, 2008

By Alan D. Akerman

This paper describes the significant advantages and improvements in operational availability, reduced breakdowns, and overall cost reductions that can be achieved through the application of a Reliability Centred Maintenance (RCM) program, including Condition Based Maintenance (CBM) and Equipment Health Monitoring (EHM), in a mine environment. It uses a case study to illustrate the essential elements that constitute the basic requirements to establish such programs. This CBM case study analyzed the Load-Haul- Dump (LHD) vehicle sub-systems and their dominant failure modes, as a precursor to the development of condition indicators. The case study describes a disciplined process to enable condition indicator development and qualification in support of a CBM program. The identified condition indicators vary from readily applicable off-the-shelf monitoring systems and techniques, through to "leading edge" technologies that require further research and development. The paper also explores the developments that have been made in the combination of expert system software associated with modern computer based control systems, and the availability of "intelligent? sensor technology that complement the control system capability.

May 1, 2002

By L. Cifuentes, J. M. Casas

The treatment of aqueous CuSO4-H2SO4- As-Sb solutions by electrodialysis in order to separate and concentrate species of interest has recently been studied. Results show that it is possible to separate copper from arsenic in electrodialysis cells. The separation of copper from antimony is also possible. Transport rate ranges that could be achieved, depending on experimental conditions, are 0.2 to 0.6 mol per hour per square metre of membrane for copper, 0.65 to 2.8 for sulphate, and 0.016 to 0.03 for arsenic. Transport rates for antimony were inconclusive due to its very low solubility in the studied systems. Solution agitation and increasing temperature markedly increased the process rates. Advancements in this area require further work in both the thermodynamics (speciation) and kinetics of complex CuSO4- H2SO4-H2O systems, where impurities, other than As and Sb, and additives should be taken into account to gain a deeper understanding of the application of ED to copper electrorefining electrolytes

Jan 1, 2004

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By Subrata Dutta

Sindesar Khurd Mine is situated in Rajasthan, India, and operated by Hindustan Zinc Ltd, under Vedanta Group. The base metal mine is high in reserves of Lead, Zinc and silver and has been producing since 2007 with initial production of 0.3 mtpa. Recently the mine has gained prominence as a base metal underground mine in introduction of latest mining techniques and achieving high production at lowest costs. The promising Lead-Zinc reserves of Sindesar Khurd Mine (SKM) and high-tech exploration adopted by Hindustan Zinc Ltd (HZL), (Vedanta Group), raising the reserves and resources from a meager 9 Mt (1997) to 81 Mt (2012), has prompted HZL management to ramp up the mine production from 0.3 mtpa (2006-07) to 2 mtpa by 2013-14 with ambitious plans to reach 3.5mtpa subsequently (presently largest underground metal mine in India). The complete trackless system underground mine, recently equipped with latest leaky feeder communication system (unique in India), utilize modern drilling, mucking and hauling equipment aided with various utility/service vehicles. Excavation optimization and quality recovery maximization from the open and post filled stoping methods, continual expert analysis and feedback from International consultants like AMC (Australia) and SRK (UK), and involvement of renowned bodies in management excellence, have lead the mine towards highest productivity and lowest mine operating cost, earning the mine a prominent place in the global base metal industry. The paper deals with how the various challenges in mine planning and designing, mine development, operator skill, equipment introduction and maintenance, expertise availability, provide training and exposure to officials, prompt and effective communication/service, control of ground vibrations, maintain ventilation standards etc are faced in attaining high operational excellence and thus attain a record mine output/man shift (OMS) of 14 ton/man shift with targets to reach 20 ton/man /shift. Scientific designing using 2D/3D numerical mine-modeling techniques, faster stope sequencing with introduction of paste filling ( first time in India),latest leaky feeder communication system, control ground vibration to stringent standards using electronic delay system, faster raising techniques using raise borers to enhance development and ventilation, cavity scanners to monitor large stope voids, fast shaft sinking at 100 m/month(Chinese expertise) and maintaining adequate ventilation with close software monitoring are some of the highlights discussed in the paper towards achieving the targets.

Aug 1, 2013

When selecting a method for monitoring crack growth in pipeline steel, the sensitivity or crack-size resolution plays a dominant role. Even though there are several visual and non-visual methods, the direct current potential drop (DCPD) method is very effective for monitoring crack growth because of its resolution. This method has been used for the past few decades and has gained increasingly wide acceptance in fracture research as one of the most accurate and efficient methods for monitoring the propagation of cracks. Furthermore, most R&D experience has proven that the electrical potential method can be used in most "aggressive" environments. For these reasons, the DCPD method was selected to design a testing machine to monitor corrosion fatigue crack growth. The use of finite-element modelling is shown to facilitate the application of the DCPD method for monitoring crack growth in steels. The 2D model calibration provided a good description of the test data and proved more accurate than the analytic Johnson's formula.

Jan 1, 2005

By D. Berkley

The competitive pressure, the increasing energy costs and the environmental regulations impose substantial challenges to the definition of power plants serving industrial facilities. Primary mining and metallurgical facilities have even greater challenges because they are often located remotely, where the fuel supply can be a problem. The absence of a power grid imposes challenges on the reliability and quality of the electrical energy supply. In addition, the facilities usually require thermal energy too, not only electricity. This paper outlines these types of issues that have to be considered when defining a cogeneration plant integrated with a remote located industrial facility. It is addressed to the ?users? of cogeneration facilities rather than to ?generators.? The focus is on analyzing various site-specific design considerations to pre-screen the feasible cogeneration alternatives and minimize the number of options to be analyzed from the economics viewpoint. This approach could substantially reduce the engineering effort and schedule during the feasibility phase of the project. Part 1 of this paper (Berkley, 2003) provides a basic understanding of cogeneration plants of various types to establish a common language. Part 2 outlines and analyzes specific issues that could be of help in the definition of cogeneration installations for remotely located industrial facilities, with a focus on mining and primary metallurgical plants.

Mar 1, 2003

By T. G. Joseph, G. W. Hansen

"This paper considers the duty cycle of an electric cable shovel and correlations with measured passive seismic responses of the underfoot oil sands material in-pit. It has been observed that the cyclic activity during operation of any shovel in the oil sands environment causes the material to deteriorate and provide a less than ideal footing for this large item of equipment, whose dead weight approaches 1500 tons with a footprint of merely 75 sq. yd. Consequences are manifested in the form of carbody and side frame cracks, and associated downtime, maintenance activity, cost, and subsequent loss of availability.The objective of these considerations, as part of the Oil sands-Equipment Interaction Program (OsEIP), currently a joint venture between Syncrude Canada Ltd., James Progithin International (JPi) Ltd., Caterpillar Inc., P&H MinePro and the University of Alberta, is to identify and provide feedback to the manufacturer and end user of adverse shovel-ground conditions. This would enable the manufacturer to incorporate greater knowledge into the design process and the end user to direct operations in an enhanced proactive maintenance stance."

Jan 1, 2002

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By D. W. Rogers

Several commercial polyacrylamide flocculants most widely used in Western Canadian mineral processing plants have been analyzed chemically and compared in standardized settling tests as aids to thickening and clarification. Data are included for both dry and liquid-type flocculants. Percentages of active ingredients in these commercial products varied Widely. Performances were compared on the basis of: equal additions of active ingredients, nearly equal molecular weights and nearly equal degrees of ionic character. Based on zone settling velocities and supernatant clarities of siliceous slurries coagulated by lime additions, dry flocculants proved more economical than liquid flocculants. Using these same two criteria, the most highly anionic were more effective than either weakly anionic or non ionic polyacrylamide- type flocculants.

Jan 1, 1978

By D. S. Flett

"The current state-of-the-art of chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is reviewed. General considerations regarding the various flowsheet steps are examined and options discussed. Then, individual flowsheets are presented and discussed. Finally, the forward prospects for chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is considered and conclusions drawn concerning the likely application of this technology in the future. IntroductionHydrometallurgical processes for treating sulphide concentrates, in general, have received considerable attention over the last three decades or more. Many flowsheets have been developed, many pilot-plant studies have been undertaken and several processes are now successfully operating. For example, direct ammoniacal pressure leaching has been used by Sherritt Gordon Mines since the 1950s to extract nickel from pentlandite concentrates, the roast-leach-electrowin route is widely used to recover zinc from sphalerite concentrates and direct sulphuric acid pressure leaching of sphalerite concentrates has been successfully commercialized. Also, Duval Corporation operated a direct cupric/ferric chloride leaching process (Schweitzer and Livingston, 1982) with electrowinning to recover copper from chalcopyrite concentrates, this process (now closed) being the only chloride process which has been commercialized for a sulphide flotation concentrate. Despite these developments, it has long been considered, particularly for copper sulphide concentrates, that direct hydrometallurgical processes are in the main unlikely to be able to compete successfully with smelting for large-scale operations of simple high-grade single metal concentrates. As long as such concentrates can be produced commercially, smelting is likely to remain the principal processing route (Flett, 1981). This view is being challenged nowadays through pressure leaching developments made by Dynatec and CESL in Canada and the recent start-up of the Western Metals Gunpowder plant at Mt. Gordon in Queensland (Flett, 2000). Complex sulphide ores offer even greater opportunities because of the ability to produce a bulk sulphide concentrate from the complex sulphide ore with considerably higher metal recovery than is often possible from the production of individual metal sulphide concentrates from differential flotation. Interest continues to focus on hydrometallurgical solutions to these processing problems, particularly with regard to chloride hydrometallurgy. This paper, therefore, reviews current state-of-theart with respect to chloride hydrometallurgy"

Jan 1, 2002

By R. Loney, M. Militzer

There is a significant demand for new high strength steels with fine grain sizes for structural applications. One approach in this regard is to develop hot-rolled HSLA steels where refining the microstructure leads to increased strength levels, e.g. 700 MPa yield strength, that can be attained by suitable modifications of chemistry and processing. Here, an HSLA steel is investigated that contains 0.05wt%C-1.65wt%Mn-0.20wt%Mo¬0.07wt%Nb-0.02wt%Ti and approaches the above strength class. The ability to control and predict the mechanical properties of hot rolled steel depends strongly on the thermomechanical processes, which the steel undergoes. The final microstructure and, thus, the properties of the hot-rolled steel are a function of the austenite decomposition obtained during accelerated cooling on the run-out table and precipitation during coiling. The austenite-to-ferrite phase transformation under run-out table conditions has been investigated using a Gleeble 3500 thermomechanical simulator equipped with a dilatometer. The effects of cooling rate and initial austenite microstructure including the degree of work hardening on austenite decomposition kinetics and ferrite grain refinement have been quantified. Results show that grain refinement can be optimized by the presence of work hardened austenite and accelerated cooling. Based on the experimental results, a model is proposed to predict the transformation start temperature and the resulting ferrite grain size for run-out table cooling conditions.

Jan 1, 2004