Search Documents

By J. R. Eastwood

"H.D.P.E. Piping in the Mining IndustryThere has been much use· ms.de of high density polyethylene pipe in the mining industry over the past several years. This is not only in new installations but al.so in areas where other piping materials such as wood, transite, concrete and steel have worn out and failed.The uses of H.D.P.E. in the mining industry are as follows:Tailings disposal linesMine water supply linesTailings water return linesHydraulic backfill linesPit drainageCorrosive liquid supply and disposal linesH.D.P.E. pipe has many advantages for both underground and above ground installations. It is tough, flexible, weather resistant and inert which makes the pipe suitable for many installations."

Jan 1, 1975

By C. Arson

"Optimizing hydraulic fracture injection parameters in order to maximize hydrocarbon extraction and to avoid extensive borehole spalling is still an open issue. In this paper, the Differential Stress Induced Damage (DSID) model is employed to simulate the anisotropic damage distribution around pressurized boreholes drilled in fractured shale. The loading path is purely mechanical: excavation and fluid injection are simulated by stress relaxation followed by pressurization. We investigate the effect of pre-existing fracture orientation, in-situ stress and injection pressure on the propagation of anisotropic damage during pressurization. Finite Element results indicate that (1) damage initiates and develops when the ratio of two in-situ stress component deviates from 1, and the magnitude of damage is proportional to this stress deviation; (2) For a given in-situ stress field, damage initiates for a certain threshold of injection pressure, and the damage zone extends as the injection pressure increases; (3) A pre-existing fracture only affects the damage zone locally; the orientation of that fracture does not affect the damaged zone, which is controlled by in situ stress and injection pressure.INTRODUCTIONHydraulic fracturing is used to increase shale permeability and to enhance hydrocarbon extraction. In order to maximize the extraction ratio and to avoid wellbore spalling and clogging during fluid injection, the parameters related to injection for each particular site need to be optimized. Therefore, it is necessary to clearly understand how shale responses upon excavation and pressurization.It is well known that breakouts grow in the direction of minimum compression and that plastic deformation around wellbores tends to arrest breakouts (Zoback et al., 1985). Laboratory acoustic emission tests revealed that fractures propagate along the direction of maximum compression stress, and fractures (breakouts) are surrounded by the Excavation Damaged Zone (EDZ), in which rock properties are weakened by the presence of micro cracks (Eberhardt et al., 1999; Martino et al., 2004). The anisotropy from orientated foliations and cracks may influence the development and propagation of fractures and breakouts (Everitt et al., 2004). Sonic televiewer logs proved that during hydraulic fracturing, fluid injection further alters the stress distribution (Evans et al., 2005). Shale natural fabric strongly affects the evolution of the EDZ around boreholes."

Jan 1, 2015

By K. Kudo

Magnesium rods of 99.95% purity and approximately 6 mm in diameter were continuously cast at rates of between 15 and 25 mm/min by a heated mould process and their mechanical properties evaluated. It was found that rods cast at 15 and 20 mm/min consisted of a single crystal, while rods cast at a speed of 25 mm/min were multi-crystalline and showed a unidirectional structure. Although room temperature tensile ductility to fracture varied widely, it was found that with an appropriate crystal orientation, cast rods can exhibit elongation by as much as 215%.

Jan 1, 2006

By Laura Mottola

This paper outlines a framework for ensuring the success of the implementation phase that follows research and development of new mining technologies and systems. It is based upon recent and past lessons learned that have demonstrated the critical challenges to effective technology transfer, which frequently receive inadequate attention within the culture of the mining business. The paper focuses on mining automation implementation challenges and then outlines a Roadmap which is proposed as an integrated framework to deal with the key aspects of people, process and technology. This framework is built upon: assembly of a Strategic Team to develop a Roadmap; fully understanding the business requirements of the technology initiative; defining Key Performance Indicators in a Balanced Score Card; performing a Stakeholder Analysis to identify the affected groups; and finally developing a master Project Plan to execute the Roadmap.

Oct 1, 2009

By K. Duckworth

The treatment of Turam data by conventional procedures does not permit the interpreter to make any estimate of induced current magnitudes. This problem may be overcome by using an alternative data treatment procedure. It is shown that the conventional and alternative procedures are equally satisfactory in terms of their ability to provide the location of line currents and estimates of conductor quality. A full description and evaluation of both procedures is presented in conjunction with field examples to show how the alternative procedure may assist interpretation when used to complement the conventional approach.

Jan 1, 1973

By Sang-Kyun Woo

The electric power conduit (EPC) in Korea has been constructed since 1978. Facing the challenge of safety and sustainability of the EPC, it is urgent to develop an inspection strategy and maintenance system for the structure based on the concept of life-cycle management. This paper introduces the newly developed mobile inspection and diagnostic system of the EPC. The novel aspect of this particular system is the integration of non-destructive mobile inspection techniques with BIM (Building Information Modeling) and LBS (Location-Based Service). BIM is an ideal tool and platform for developing an inspection and diagnostic system, and RFID (Radio Frequency Identification) is a useful tool to construct USN (Ubiquitous Sensor Network) for LBS. The goal of this research is to establish an EPC inspection and diagnostic system concept based on BIM and LBS using RFID. In this research, a BIM model of OPENTBM tunnel for EPC will be established to show the integration of 3D CAD with the inspection data. An EPC?s maintenance database, which includes the deterioration types of the structure, inspection records, and repair methods, was designed to interact with the BIM. The system will be implemented by the BIM with the related database, in which the construction geometry and all related information are stored. The proposed system was designed to utilize the inspection and diagnostic system under the USN environment using RFID in EPC directly.

Aug 1, 2013

By Matthew P. Wickham

The use of existing mine records in conjunction with an appropriate classification scheme can be used successfully to identify and characterize the composition of existing waste rock facilities where traditional approaches based on sampling may be impractical or costly. This paper describes an alternative approach used in an acid rock drainage investigation at a porphyry copper mine with numerous waste rock dumps of varying ages and composition. The approach integrated detailed lithologic and mineralogic information about the ore body and overburden materials with records of pit development and dispatch. A waste rock characterization matrix was developed for the site to meaningfully classify lithology and mineralogic composition of the waste rock. The approach resulted in a focused geochemical testing program and facilitated interpretation and application of the test results.

May 1, 2002

By Gordon G. Duncan

Historical Sketch Occurrences of native copper have been known along the Arctic coast of Canada, especially in the vicinity of the. Coppermine river, since the early part of the eighteenth century (See map, Figure 2, insert). In 1769, Samuel Hearne, a clerk of the Hudson's Bay Company at Fort Churchill, was sent to explore the 'copper mines' from which natives had been reported to secure copper for tools, fishing spears, etc. After two successful attempts, he reached the Coppermine river in 1771, accompanied by Indian guides. This hazardous trip was indeed a remarkable feat when one considers the vast distance covered, a great deal of which was barren lands. At Bloody falls, (See Figure 1) on the Coppermine river, Hearne's Indians swooped down on a party of sleeping Esquimaux, who gathered there each summer to fish, and murdered the entire band encamped on that side of the river. Hence the name of the falls. Hearne's knowledge of minerals was undoubtedly limited. He reported having seen the copper mines from which the natives were securing the copper, but he failed to prove the economic possibilities of the copper occurrences or to give an accurate description of any deposit. Sir John Franklin visited the area in 1821. He and other members of his expedition, namely, Richardson, Back, Kendall, and Hood, reported native-copper float to occur in the vicinity of the Coppermine river and Bathurst inlet.

Jan 1, 1931

By Yun-Soo Lee, Su-Hyeon Kim, Hyoung-Wook Kim, Joon-Hyeon Cha

A7075 aluminum alloys have high strengths but poor corrosion resistance. In order to improve the corrosion resistance, a clad sheet is suggested, that is the A7075 alloy sheet bonded to A1XXX or A6XXX aluminum alloy sheets which are surface layers with good corrosion resistance. Mechanical properties of the clad sheets are determined by the combination of the component layer sheets, and thermomechanical treatment should be precisely designed when the strengthening methods of the core and the surface alloys are quite different. In the present study, three-layered A6022/A7075/A6022 clad sheets were fabricated by roll bonding process. Simplified processes incorporating a twin roll casting were also suggested in order to reduce the processing cost. Several temper methods composed of rolling, annealing, solution treatment, and aging were suggested in order to optimize the mechanical properties of the sheets. The strengths of the clad sheets were compared with the bare A7075 and bare A6022 sheets.

Jan 1, 2015

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By Michel Fontaine, Bruno St-Cyr

"The mission of the CENTRE DE RECHERCHE INDUSTRIELLE DU QUEBEC (CRIQ) is to stimulate economic development by guiding businesses in their pursuit of innovation.With a comprehensive approach to their needs, CRIQ provides businesses with expertise based on the most recent developments and insights in the fields of:Research and Development ServicesAutomation and production processesDevelopment of industrial equipmentEnvironmental biotechnologiesTesting and Product Qualification Services Industrial and Technological Information ServicesConsultancy and competitive intelligence servicesIndustrial information bankStandardization ServicesElaboration of standards and product certificationSystems registrationEXPERTISE COMPETENCE, INNOVATIONSince its founding in 1969, CRIQ has been involved in over 100,000 projects. The results of its research and development services have enabled it to build over one hundred pieces of equipment, almost all still in operation today. CRIQ has been and remains the driving force of innovation and expertise on the industrial scene, offering highly competitive solutions to a clientele from numerous industrial sectors.CRIQ became a crown corporation operating on a commercial basis on June 30, 1997. This change in its corporate structure has enabled it to put a marked emphasis on trade and implement an array of new operational practices.The formation of marketing companies with private partners, the opening up to corporate business and international markets, the new directions for internal research and the strengthening of its marketing component are among the activities CRIQ has initiated over the last fiscal year to finally reach its cruising speed."

Jan 1, 2000

By Denis Thibodeau

The selected mining method for the Rodeo lower Zone is slot and slash. Initial design indicated that the stope height should be limited to a maximum of 18 m, thus six levels were needed to extract the ore. Higher stope height in the Rodeo Lower Zone means less development thus less capital required to extract the available reserves. It was proposed to eliminate one level by establishing 30 m and 24 m level intervals. To ensure that no stability problems will be encountered by eliminating one level, a Matthew analysis, based on diamond drill core information, was performed for the Lower Rodeo Ore Body. In addition, comparisons between the rock mass quality of Meikle Main Zone below 1825 L and Meikle East Zone between 1600 L and 1750 L with the rock mass quality of the Lower Rodeo were made

May 1, 2002

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end-use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here, we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilization to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilized to produce more effective dispersant systems which allow the preparation of added value, higher solids and finer particle size calcium carbonate slurry products. IntroductionConcentrated aqueous dispersions of fine particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently, more than 10 Mt of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e., its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximize the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimize drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003

By R. E. Gilmore

PREAMBLE THIS PAPER comprises material presented in two separate 'Papers at the British Commonwealth Scientific Specialist Conference on Fuel Research held in London, England, in July, 1950. These papers are now available for publication in Canada, since only essential parts of the conference discussions, in addition to the resolutions resulting therefrom, will be published in the official Proceedings of the Conference. Inasmuch as the information presented concerns Canadian organizations and training facilities for fuel research, it should be of general interest to Canadian scientists, and especially to the Coal Division of the Canadian Institute of Mining and Metallurgy. Part I, the alternate title of which is Facilities in Canada for Fuel Research and for Exchange of Information and Staff, does not include research on peat, oil shale, petroleum oils in general, and natural gas, and omits studies of the geology, constitution, and production of coal. Special reference is, however, made to research on the heavy crude oils and bitumen of the Western Prairie Provinces, and particularly to their production and treatment to produce crudes for oil refinery processing.

Jan 1, 1951

By M. Pekguleryuz, S. A. Argyropoulos

"The recovery of additions in light metals is an important parameter influencing consistency of the finished product, which ultimately means cost. Recovery is a function of many parameters such as assimilation speed, addition density, addition practice, liquid metal processing conditions, etc. In liquid metal processing operations, it is desirable to have the maximum possible recovery at the shortest possible time.In this paper a new index will be presented, namely, the rate of recovery (RR). This index quantifies the addition recovery and introduces the time dimension in the recovery increase. As such, the RR equips the liquid metal practitioner with an accurate picture of addition assimilation in liquid metals. Results will be presented on how this index is applied to a variety of additions in liquid aluminum. IntroductionThe data on addition assimilation kinetics offer a valuable parameter describing how fast a given addition enters the metal bath. These data may be expressed as gr m-2 s-1 of additive for a set of experimental conditions which might include bath temperature and degree of bath agitation among others. However, the liquid metal processing practitioner is more interested in the recovery of additions. In other words, the point of interest is the percentage of the used addition entering the metal bath. Ideally, the addition recovery can reach the 100% level. However, in practice, the addition recovery never or rarely reaches that level. Many factors can contribute to this. Some of these factors can be slow assimilation kinetics, addition density, addition practice, turbulence of the melt, etc. In some cases, sloppy addition practices can contribute to low recoveries, or even worse, to erratic recoveries.In this paper a new parameter is introduced. This parameter relates the maximum addition recovery observed over the time needed to achieve this maximum recovery."

Jan 1, 2002

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By T S. Cochrane

A variety of practical tests have been tried in the mining industry to determine the support properties of mine roof bolts. Such tests include torsion wrench readings, hammer blow tests and the use of plates with built-in tension indicators. This paper gives some details of pull tests with a hydraulic jack, as carried out in coal mines of western Canada. M A~Y criteria exist for establishing the efficiency of roof bolting, and the one adopted de-pends on the nature of the problem and on the individual leanings of the investigators. Consequently, sufficient studies have not been made from a common viewpoint or under similar geological and techno-logical conditions to compare these methods of evaluation. However, regardless of whether certain tests provide sufficient factual data to form a basis for theoretical research on bolting or not, many of these tests can and do provide a positive means of judging the suitability of chosen roof bolting techniques and equipment under definite geological conditions.

Jan 1, 1963

By Kathleen A. Altman

"This paper supplements the information provided annually at the Canadian Mineral Processors Operators Conference regarding the education of Mineral Processors in Canada. The purpose of the paper is to provide information regarding the engineering accreditation process in the United States and the universities that offer programs in Mineral Processing and Extractive Metallurgy in the U.S.There is a critical shortage of trained Mineral Processors and Mining Engineers world wide. The Society for Mining, Metallurgy and Exploration (SME) formed a task force to evaluate the national needs for trained engineers and to track the number of engineers who graduate from U.S. universities each year. The statistical information for Mining Engineers is well-developed. The current effort is to assemble similar information regarding students who graduate with expertise in Extractive Metallurgy and Mineral Processing as well as to explore the limitations of the accreditation system in the United States and its impact on the education of Mineral Processors. The long-term objective is to develop a data base regarding Mineral Processing programs and Mineral Processing graduates that is as complete as the one that has been maintained by the Canadian Mineral Processors.INTRODUCTIONIn the United States engineering curricula are accredited by ABET, which was formerly known as the Accreditation Board for Engineering and Technology. The objective of ABET accreditation is to ensure that educational programs in applied science, computing, engineering and technology meet quality standards set in conjunction with the professional organizations that represent professionals in the industries which hire students graduating from those educational programs. For example, the Society for Mining, Metallurgy and Exploration (SME) is the lead society for accrediting Mining Engineering programs in the U.S. For Materials Science and Metallurgical Engineering programs, the lead society is The Mineral, Metals and Materials Society (TMS). SME is a cooperating society for accrediting Metallurgical Engineering programs. Cooperating societies for the accreditation of Materials Engineering include the National Institute of Ceramic Engineers (NICE), the American Institute of Chemical Engineers (AIChE) and the American Society of Mechanical Engineers (ASME)."

Jan 1, 2008

By J. O. Pitts

"Background The preponderance of Canada's coal resources is located in areas remote from high demand domestic users and at some significant distances from deepsea ports. This places great demands on the transportation system and has forced the coal and the transportation industries to adopt highly efficient methods of handling the product and hauling it to market position. Most of the coal not consumed in minemouth thermal power stations is carried by rail over lines operated by the two transcontinental railway systems, Canadian National and Canadian Pacific. These rail networks are extensive and have the advantage (as compared to most other North American railways) of being able to handle coal movements from origin through to destination without interchange to other rail carriers. Coal SourcesWith exception of the coal produced in Cape Breton, Nova iScotia, all the significant shipping volumes in Canada emanate ifrom mines located in the three most westerly provinces. Figure I ishows the geographic distribution of the major mining operaitions shipping coal to domestic and export markets. The prinicipal routes and the tonnages carried (1980 calendar year) are ialso indicated. iThe 1980 shipping data are summarized in Table I. Saskatchewan lignite began moving from Bienfait to Thunder Bay by CP Rail unit trains in mid-1981 at the rate of one million tonnes per year. The product is handled through Thunder Bay Terminals and delivered directly to a nearby Ontario Hydro electrical generating station."

Jan 1, 1985

By D. W. R. George, J. L. Stewart

Developments in the last decade, which have contributed to increased productivity and decreased coke rates in the iron blast furnace, are reviewed. Future progress in blast-furnace practice is also considered.

Jan 1, 1966