Search Documents

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By Yum Xiaoquan, Turgut Yalcin

"A laboratory study was carried out to determine the potential role and effect of ultrasonic irradiation in the flotation of a Sudbury copper-nickel sulphide ore. The use of ultrasound was tested separately at the pulp preconditioning, collector conditioning and flotation stages. While no significant benefits were evident in the latter two cases, ultrasonic preconditioning of pulp improved the grade-recovery performance and had the prospect of reducing reagent consumption rates. Tests were conducted on both the normal and oxidized ore samples, and several variables were investigated, including ultrasound frequency (25 kHz and 45 kHz), ultrasonic power (up to 1.6 W/cm2), duration of ultrasonic treatment (up to 60 minutes), and the intensity of pulp agitation employed during the application of ultrasound. Ultrasound frequency of 25 kHz and duration of 15 minutes yielded satisfactory results. Changes were found to occur in the temperature, pH and Eh of the pulp during ultrasonic processing. The favorable effects of ultrasound observed in this study were attributed primarily to its surface cleaning capability.INTRODUCTIONThe use of ultrasound for the surface cleaning of objects is well known. Ore flotation is based essentially on the surface properties of minerals, and hence stands to benefit from ultrasonic treatment which may help restore mineral surface characteristics that might have been lost or modified through oxidation, etc. Expected outcomes of this method of treatment include improved flotation kinetics, higher recovery, better selectivity, and savings in reagent consumption, as has been demonstrated by various researchers (Aldrich and Feng 1999, Celik 1989, Ozkan 2002, Letmathe et al. 2002, Nicol et al. 1986)."

Jan 1, 2005

By B. V. Knelson

"GENTLEMEN:This paper will deal with centrifugal separation - theory and practical, and since the Knelson Concentrator is the only centrifugal concentrator with a properly fluidized bed, this paper will cover the Knelson Concentrator and its technical and structural advances over the last five years. As I am the person with the most experience in this line, I guess I am some kind of an expert; what kind I’m not sure, but some kind.This type of concentrator truly was developed because I’m lazy and I constantly look for easier ways to do things. My experience in the mining industry was very limited but I did realize in looking at placer operations, which is the application where I spring from, that it was tremendously labour intensive and my first reaction that ""my god, there must be some method or way-of handling product in a more efficient (and you can read that as being able to quickly recover very fine particle gold) way than was being shown at that time"". So, the Knelson Concentrator was born - about 6 or 7 years later. Our first attempt was a cone with about the same degree of slope as our present machine and since we had no knowledge of vibration dampening and centrifugal forces at that point, it was just an idea that this should work.Our first run was one of twenty minute duration. We did make that first machine variable speed by a mechanical belt system and we found that at about 240 rpms we were virtually shaking the gravel plant apart that we were attached to. So the first run was twenty minutes and back to the drawing board. However, that first run produced a concentrate so superior to anything we had seen previously, that we knew without any question, we were definately and accurately on the right track."

Jan 1, 1985

By Stephen R. Grano, Jon Glatthaar, Philippe Steinier, Christopher J. Greet

"The importance of the oxygen content of sulphide mineral pulps in determining which reactions occur, and their subsequent influence on flotation behaviour is grossly underestimated in most operating concentrators. While pH is routinely monitored, Eh and dissolved oxygen measurements are obtained infrequently. However, dissolved oxygen measurements in conjunction with other pulp chemical parameters (i.e. pH, Eh, and EDTA extractable metal ion analysis), can provide valuable insight into where and what type of reactions are occurring within a circuit. Unfortunately, these readings yield “instantaneous” measurements of the pulp chemical parameters.What is needed is a means of establishing how reactive a pulp is, and how this reactivity changes as components of the system are manipulated. Oxygen demand provides an opportunity to do this. Several attempts at measuring the oxygen demand of a pulp have been made in the past with varying degrees of success. Most notable among these are Noranda and BOC Gases.Learning from these experiences, Magotteaux have developed the MagO2 ® demand vessel to measure the oxygen demand of mineral pulps. This paper described the apparatus, and through a case study on Broken Hill lead/zinc ore demonstrates how the MagO2 ® demand vessel is used.INTRODUCTIONThe role of oxygen in flotation is complex. While a considerable body of work exists demonstrating the strong involvement of oxygen in the interactions between sulphide minerals and collector (Gaudin and Finkelstein, 1965; Gaudin, 1974; Woods, 1984; Laajalehto, Nowak and Suoninen, 1993), the presence of oxygen can also affect the oxidation state of sulphide and non-sulphide minerals, which can impact on their flotation behaviour. Further, sulphide mineral oxidation is related to their oxygen demand (Spira and Rosenblum, 1994)."

Jan 1, 2004

By Patrick Frenette

Résumé La Mine Goldex entrera en production au 2ième trimestre de 2008. Pour permettre une production de l?ordre de 6960 tpj, le forage ITH à une pression de 400 psi (28 bar) à été sélectionné. Il s?agira d?une des premières applications du forage ITH à cette pression sous terre. Cet article traitera des gains anticipés et montrera certains résultats préliminaires. Il sera aussi question du bras manipulateur utilisé pour manipuler les tiges de forage. Abstract The Goldex Mine will start production in the second quarter of 2008. In order to achieve a production of 6960 tpd, ITH drilling at 400 psi (28 bar) was selected. ITH drilling at this pressure will be one of the first underground applications. This paper will discuss the anticipated gains and show some preliminary results. The use of the rod handler will also be discussed.

Feb 1, 2008

By S. F. Featherby

"This paper traces briefly the historical development of coal handling systems to meet the needs of a rapidly developing thermal power generation technology. The wide range of operating requirements is demonstrated by comparing and contrasting the Wabamun GS of Calgary Power Ltd. and a typical modern Ontario-Hydro thermal plant. The problems of safe storage of large tonnages of coal in stockpiles are discussed, together with recommendations for stockpile management. The development of coal bunkers and their management is discussed in detail, together with future trends in the industry."

Jan 1, 1966

By Elizabeth Wademan

Recessions Eventually End ??Companies aggressively cutting production and inventories ??these will come in-line with demand ??U.S. home inventories are declining ??Housing becoming more affordable ??Global trade recovering after collapsing ??Lower oil prices should act as a stimulus Protracted Deleveraging Process Beginning ??Era of leverage-driven consumption is over ??Greatest destruction of consumer wealth since WWII ??Consumers will no longer be able to substitute capital gains for savings ??Shift towards savings will be a headwind to economic growth ???Paradox of Thrift?

May 1, 2009

By C. S. Maggs, L. Shwydiuk, H. W. Newcomen

The southwest wall of the Lornex Pit at the Highland Valley Copper mine has been experiencing slope displacements since 1978. Measures to manage the displacements on previous pushbacks have included stepping out, scheduling pushbacks to unload the crest of unstable areas, slope dewatering and mining with intensive slope monitoring. The final pushback on this wall is currently being mined and substantial modifications to the slope geometry could prove to be uneconomical. As a result, a campaign of surface water collection and diversion, horizontal drainhole drilling and deep well drilling is currently underway to maintain an acceptable degree of stability to the end of mine life. The various factors contributing to instability, including engineering geologic controls, rock mass strength, and surface and groundwater hydrology are presented. Movement trends, displacement magnitudes and stability analyses results are also discussed.

Jan 1, 2003

By E. A. Lowe, J. W. Smith, C. W. Overton

"The operations of Bethlehem Copper are situated in the south-central interior of British Columbia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Columbia.The minerals are chiefly chalcopytite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies some pyrite is present. Average grade of mill feed is 0.55% copper.History of Milling Operations Production commenced in December 1962 at a rate of 3,000 tpd in a plant that comprised two-stage crushing followed by rod and ball milling. Production ratings were increased to 6,000, 10,000 and 12,000 tpd by the addition of a further stage of crushing and more rod and ball mills. When the last expansion was completed tonnage throughput exceeded the 12,000 ton designed rate and was stabilized at 15,500 tpd.However, recovery did not meet expectations at the expanded rate because of coarse flotation feed. Capacity in the rod mill circuits exceeded the subsequent fine grinding capacity, resulting in poor liberation. Studies were initiated to improve recovery without decreasing throughput.Description of Operation Prior to Pebble Milling Crushing with primary, secondary and a closed tertiary stage proceeds at a scheduled 20.5 shifts per week. Fine ore screened on 1/2"" x 4"" apertures is stored in a 30,000-ton bin ahead of two 12.5' x 15' rod mills. Rod mill discharge joins secondary ball mill (one 10.5' x 14' and one 11' x 14') discharge for classification in a single 50"" cyclone which closes the secondary mills. Overflow from this cyclone is split between three third-stage ball mill-pump-cyclone circuits (two 11' x 14' and one 12.5' x 15'). Prior to addition of the two pebble mills the flotation feed was produced by this three-stage grinding system. Grinding criteria are shown in Table I."

Jan 1, 1975

By Barrie Robb

Outline 1. Mackenzie Aboriginal Corporation (MAC) 2. ACR background 3. ?Learning from Experience? project - What - Why - lessons 3. How Industry could contribute to sustainable Aboriginal communities 4. Concluding words What is the Mackenzie Aboriginal Corporation (MAC)? ? Aboriginal owned ? Established construction capabilities ? Commitment to development of northern resources ? Partners have extensive experience

May 1, 2008

By W. C. Zhu, C. H. Wei, L. L. Niu

With an increase of mining depth, a series of mining-induced hazards such as rockburst, coal and gas outburst, roof collapse, and water burst are getting more serious and more frequent. The intrinsic mechanism responsible for the occurrence of mining-induced hazards is the damage and unstable failure of rockmass or coal seam. The most distinct difference between deep and shallow levels is the so-called three ‘high’ (H3) conditions, i.e. high geo-stress, high fluid pressure and high geo-temperature. Therefore, the response of rock or coal to the deep mining operation is a phenomenon involving thermal (T), hydraulic (H), and mechanical (M) processes. Most importantly, mining excavation may vary the rock stress condition greatly, which may be a key factor to trigger the mining-induced hazards such as rockburst. In this regard, it is of great significance to clarify the damage and failure mechanism of rock and coal under coupled THM conditions, in order to clarify the rock failure mechanism responsible for the occurrence of mining-induced hazards. Thereafter, the mining-induced hazards cannot be predicted with confidence by considering each process independently. Of course, the requirement to include coupling of these processes depends on the specifics of the mining-induced hazards under consideration. For example, the water inrush is considered as a coupled hydro-mechanical (HM) process, in which the unstable failure of rockmass occurs under the combined contribution of geo-stress and water pressure. As for the coal mining at depth, in addition to high geo-stress and gas pressure in coal seam, the high geo-thermal condition that may greatly change the adsorption / desorption of gas and gas flow should be taken into account. Firstly, a general-purpose mathematical model for rock damage and failure process under coupled THM conditions is formulated based on damage mechanics principle, and it is solved by finite element method (FEM). In this model, the deformation and damage of rock, fluid flow and thermal transfer in rock would interact with each other, one process affects and initiation and progress of another. Then, the model is used to predict the mining-induced water outburst, where it is simulated as coupled hydro-mechanical (HM) problems. Based on the numerical simulation, the dimension of water-proof pillar is designed. Finally, the gas drainage from deep coal seam is numerically evaluated, where the coupled coal-gas interaction considering the effect of gas adsorption/desorption, gas flow in coal seam and geo-stress and geotemperature, is comprehensively taken into account. The proposed model could be used for clarifying the mechanism of mining-induced hazards in deep-level mining.

Jan 1, 2015

By R. Nendick

"IntroductionThe Ancient Egyptians recovered gold from the mud in the bottom of ponds by having teams of maidens sit around the pond dipping goose feathers dipped in grease into the mud. The gold would preferentially stick to the oily surface and was periodically washed off to give a gold concentrate. This was a forerunner of today's flotation processes.In Greek mythology Jason and the Argonauts pursued the Golden Fleece, which was a primitive form of gravity concentrate produced when gold ore slurry was passed over a sheeps fleece. The heavy gold settled and was caught in the fleece, producing a rich concentrate that allowed Jason & Company to perform the first recorded case of highgrading. The process was a forerunner of todays shuiceboxes used in placer mining.From these simple beginnings, gold metallurgy has progressed to a state where very complex flowsheets are proposed, sometimes to perform a simple metallurgical task. Figure (i) shows a hypothetical flowsheet to identify the range of unit processes that might be brought to bear on a refractory ore. The flowsheet identifies the three primary areas of gold metallurgical operations:Ore PreparationExtractionRecovery."

Jan 1, 1986

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By B. Ignasiak

Laboratory studies suggest that improvements of coke strength brought about by pre-heating caking coals before carbonization accrue from inadvertent oxidation rather than from other low-temperature changes in the coal mass. Controlled oxidation of highly caking coal, followed by laboratory carbonization, produces cokes which, in terms of a laboratory scale tumble test index, are equivalent to those obtained from prime metallurgical blends. Appropriately formulated blends of exhaustively oxidized and fresh caking coal similarly yield cokes with strength indices comparable to those of cokes made from the same coal after oxidation under optimum conditions.

Jan 1, 1979

By Sengpasith Houngaloune

Arsenic, which is a toxic and carcinogenic element, causes serious environmental problems throughout the world. It is also known as a major contaminant in the non-ferrous mining and extractive metallurgical industries, thus its disposal is one of the most important environmental issues for the mining and metallurgical industries. In order to ensure a safe disposal environment for the final wastes, stabilization of arsenic has been studied extensively with various approaches. Solidification/stabilization (S/S) represents one of the most effective methods to reduce the availability of arsenic in soil and waste by transforming toxic or potentially hazardous phases into less hazardous ones. Cement based S/S processes could reduce the solubility of arsenic in solid waste, using inorganic binders such as cement, lime, and pozzolanic materials. A new tailings management technique, called cemented paste backfill (CPB), has become widely employed for improving mining techniques and for tailing storage purpose and this technique could also enhance arsenic stabilization, by fixing the contaminants in the binder matrix. Disposal of arsenic in the form of scorodite (FeAsO4?2H2O) has been widely accepted as currently the most suitable method for stabilization and the safest known storage material. The Bio-scorodite process has been reported to be more economic and environmentally friendly method than the chemical crystallization processes. Retention of arsenic by schwertmannite (Fe8O8(OH)6SO4), a metastable ferric oxyhydroxy sulfate mineral, has gained more attention in the recent years. Schwertmannite has a large specific surface area and high capacity to adsorb arsenic in solution. Several researchers have reported that the transformation of schwertmannite to goethite could be retarded by the presence of adsorbed arsenic; therefore schwertmannite might be viable alternative for long-term storage of arsenic. In this paper, various approaches used in arsenic stabilization are reviewed with emphasis on the development in the recent years.

Aug 1, 2013

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By Sabry A. Sabour

Metal price is among the key variables in the open pit optimization and the economic evaluation process. The common approach to handle metal prices in open pit mine planning is to optimize the ultimate pit and the mining schedules using a fixed, flat metal price. In this respect, metal price is assumed to be known with certainty throughout the entire mine life, which in some cases can reach 80 years. Given the volatile nature of metal markets and the metal price cycles, the conventional pit optimization approach may generate sub-optimized mining plans, which results in either extra costs to mining projects or lost revenues, or both. Long-term operational decisions such as future pit expansions, beyond the currently optimized limits, cannot be handled using the pit optimization approach based on flat metal prices. There is a growing interest in the mining industry to model and manage such market uncertainty in the pit optimization as well as the project evaluations in order to maximize the value of mining operations. In this paper, the author will outline a practical approach to optimize the ultimate pit taking into account the volatility and variability of metal markets. The proposed approach uses a combination of the pit optimizer of the commercial MineSight package and a simulation-based economic modeling real options valuation approach employing the least-squares Monte Carlo algorithm. MineSight pit optimizer employs both the floating cone for initial optimization exercise and the standard Lerchs-Grossmann algorithm. In this paper, Lerchs-Grossmann option will be used to generate the pit shells. Real options valuation approach used in this study is based on generating multiple metal price scenarios. Metal price uncertainty is modeled using stochastic metal price models such as the geometric Brownian motion and the mean-reverting process. The mining operational scenarios corresponding to the simulated metal prices are then optimized using the least-square Monte Carlo approach. The objective is to maximize the discounted cash flow value of the project while incorporating the operating flexibility to revise the operating status of the open pit with time as new information becomes available. The focus of this work is on the practicality of the proposed uncertainty-based pit optimization approach and the difference it can make to the technical operational mining decisions. A case study of a hypothetical open pit poly-metallic mine is provided. The deposit contains copper, gold and silver grades. The run of mine ore is sent to the process plant that produces copper concentrate with copper as the main metal and gold and silver as the by-products. Four uncertain variables are considered here include copper, gold, silver prices and foreign exchange rate. Both copper price and exchange rate are modeled using the mean-reverting process while gold and silver prices are modeled using the geometric Brownian motion. The case study is performed using both the conventional flat price pit optimization approach and the proposed uncertainty-based one to compare results.

Aug 1, 2013

By Liang Zhen, Jian-Tang Jiang, Guo-Ai Li, Xiao-Ya Wang

"Deformation behavior of 2A97 aluminum alloy containing coarse secondary phases was studied using uniaxial hot compression (HC, 340–490°C, 0.4001–1 s-1). The flow stress could be described by a Zener-Hollomon parameter in hyperbolic sine function with the hot deformation activation energy of 237 kJ/mol. Based on the experimental data and dynamic materials model, processing maps were generated to demonstrate the hot workability of the alloy. The coarse secondary phases experienced dissolution by varying degree under different deformation temperature, which producing different effects on the microstructure evolution. When deformed at relatively low temperatures, a mass of fine grains shaped up in the original grains and grain boundaries, and the dominating deformation mechanism was believed to be dynamic recrystallization. As the deformation temperature rising to 490°C, most secondary phases disappeared and few recrystallized grains were observed, indicating that the secondary phases dissolved sufficiently along with dynamic recovery occurred during the hot deformation. Particle stimulated nucleation related to the coarse secondary phases was believed to promote the recrystallization and the recrystallization behavior was sensitive to deformation temperature.INTRODUCTION Al-Li alloys has received much attention as new promising structural materials in the aircraft and aerospace industries, due to their lower density, higher elastic modulus and improved fatigue crack growth resistance in comparison with the conventional commercial aluminum alloys (Ou Ling, 2015). 2A97 alloy is one of the 3rd generation Al-Li alloys targeting at comprehensive improvement of aviation aluminum alloy and applications for wing spars and ribs to other internal structures for transport aircraft. Al-Li alloys are usually formed by hot deformation, either by rolling or extruding. The deformation behavior and resulted microstructure evolution during the forming process mainly dominates the formability of the alloy and the serving performances as well. Therefore, the deformation behavior and microstructure evolution at elevated temperature need be made clear for optimizing the hot processing parameters and controlling microstructure evolution."

Jan 1, 2018