Search Documents

By C. Fleming, J. R. Goode

ABSTRACT: Data were produced from two uranium project studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. In both studies, excellent metallurgical results were produced. The loaded resins were eluted with strong sulphuric acid and recycled through RIP circuits in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low. Metallurgical results from these two campaigns are presented, along with a case study economic analysis of RIP versus the alternative processes of counter-current-decantation or filtration and solvent extraction.

Jan 1, 2011

By R. H. Walton

"In recent years the recovery of copper from low grade oxide ores has received widespread attention. The cost of treating such ores using conventional technology, such as milling and flotation, is frequently prohibitively high and copper recovery is generally low. The introduction of heap leaching, solvent extraction (SX) and electrowinning (EW) has resulted in high recoveries, good copper cathode quality and low production costs. This technology has now been successfully applied on a worldwide basis.This paper reviews the various process and design options and gives approximate capital and operating costs for a 1.0% copper ore.INTRODUCTIONAs a result of the low copper prices that prevailed for much of the last two decades, aggressive attempts were made by the industry to cut operating costs. Under such circumstances heap leaching, solvent extraction and electrowinning, to recover low cost copper from oxide ores, has received particular attention and ultimately widespread acceptance.Low grade copper ore (typically containing less than 1.0% Cu), which could not be economically treated by other methods, is placed on heaps and leached with dilute solutions of sulphuric acid. The copper rich, pregnant solution, drains from the heap into a collecting pond and is pumped to a solvent extraction plant where it is purified and upgraded. The resulting solution, termed the pregnant electrolyte, passes to the electrowinning section where the copper is recovered as high grade cathodes and sulphuric acid is regenerated, (Figure 1).This paper specifically describes the processing of copper oxides. Other copper minerals such as chalcocite and chrysocolla are also leached by dilute solutions of sulphuric acid. In practice the oxide minerals are frequently associated to varying degrees with less easily leached sulphides, such as chalcopyrite. In some cases, once the oxidized capping of the ore body is removed, the oxides are totally replaced by more refractory sulphides. Under these circumstances the leaching recovery is significantly reduced. However the principles described here for solvent extraction and electrowinning are also applicable to solutions received from heaps containing sulphide minerals, which are leached more slowly and involve bacterially induced reactions."

Jan 1, 1990

By W. C. Risley

IN the year 1933, workings at the No. 12 colliery, New Waterford, of the Dominion Coal Company, Limited, had advanced to a point where additional ventilation would soon be required. Furthermore, development of the mine was being .made to practically double the output of coal. Consequently, authorization was given to sink a shaft to the workings. The location selected is on the west side of the mine, about one and a half miles from the slope mouth and on the Low Point shore, some 250 feet from high-water mark. The cliff at this point is 40 feet high, with the land rising on a slope of about 5 per cent to the shaft. Figure 1 shows the location with reference to the colliery workings. The strata through which the shaft was to be sunk were pretty well known from diamond-drill borings previously made, and it was believed that water would be encountered to a depth of at least 250 feet to 300 feet. It was planned, therefore, to seal-off the water by the pumping of cement grout under high pressure. This method was considered to be the most economical means of handling the water during sinking, and would also result in a permanently dry shaft. Figure 2 shows a cross-section of the strata. The permanent shaft hoist and fan were to be electrically driven, which would necessitate the construction of a transmission line between the colliery and the shaft; therefore, it was arranged that the sinking equipment would have electric drive. As all equipment, materials used in construction, and supplies were to be hauled by truck, a roadway 1,800 feet long was required from the main highway to the site, and as heavy loads would be hauled during the fall, winter, and succeeding spring, this road was ballasted with 18 inches of clinkered material obtained from a burned culm bank one and a half miles distant. Actual field work was begun by the Company's own forces early in October. Work preparatory to sinking-in addition to the roadway and trans-mission line-included the construction of the reinforced-concrete shaft collar and fan drift connection; the permanent timber headframe (which was to be used also as the sinking headframe); the permanent reinforced-concrete building to house the shaft hoist and fan drive; and the erection of temporary buildings and installation of all equipment for sinking and lining the shaft and for cementation.

Jan 1, 1936

"INTRODUCTIONGold tailings retreatment plants have been operated for many years throughout the world. Several large tailings retreatment facilities have been operated profitably in South Africa since 1976 and there are tailings retreatment operations in Canada currently in production with more in the feasibility stages.The Timmins Gold Tailings Project of ERG Resources Inc. was designed to treat 8,000,000 tonnes per annum of gold tailings for an eight month operating season, and commissioning of the operation began in July 1988. The payback period for this project is about 3 years which corresponds to an IRR of 30%.This report summarizes the metallurgical characteristics of the reclaim tailings, describes the process flowsheet which was developed to enable ERG to economically recover gold from the Timmins area tailings, and reviews commissioning activities."

Jan 1, 1989

By Peter Rubie, Toni Kojovic, Fengnian Shi

"Mining companies have recognized that characterization of ore breakage plays an essential role in the design and optimization of comminution circuits.Recently the Julius Kruttschnitt Mineral Research Centre (JKMRC) has developed a new breakage model incorporating the effect of particle size, and a new breakage characterization testing device, called the JK Rotary Breakage Tester (JKRBT), which allows rapid testing of particle breakage under high energy single impact and low energy repetitive impact conditions.Positive feedback received from mining company sponsors to the new technology has prompted the JKMRC to further validate the device and the model through a formalized validation program using machines designed and manufactured by Russell Mineral Equipment (RME). The first unit was installed and commissioned at the Anglo Platinum laboratory in Johannesburg in March 2007 and four more major mining companies will participate in the validation program in 2008, including Barrick, BHP Billiton, Rio Tinto and Teck Cominco. The results from validation tests at the JKMRC and Anglo Research have shown that the JKRBT generates statistically similar breakage parameters to the traditional Drop Weight Test, but with significant advantages over its predecessor. Application of the JKRBT in geometallurgical testing with the AMIRA P843 GeM project has confirmed the JKRBT device offers a rapid and consistent method for determining the hardness of drill core samples. The JKRBT has the potential to revolutionize ore testing, with applications in laboratory impact breakage characterization of rock samples, drill cores, coal and other materials. It also stands poised to significantly advance the process control and management of comminution circuits since the concept is readily adaptable to on-line ore hardness measurement.INTRODUCTIONMining companies have long recognized that the performance of a comminution machine such as a crusher or an autogenous / semi-autogenous grinding (AG/SAG) mill depends not only on the machine operating conditions, but also on the “hardness” of the feed material to be broken. This recognition has driven significant interest in laboratory particle breakage characterisation and testing. The laboratory breakage characterization tests can be roughly classified in two broad groups based on their primary breakage modes: tumbling and impact/compression. The famous Bond ball/rod mill tests (Bond, 1952 and 1961) represent the typical tumbling test and have become the industry standard for estimating the specific energy (kWh/t) of rod and ball mills. However, as the energy application in the single particle impact tests can be well defined and controlled, the latter have received significant attention in the last 30 years. It was estimated that mining companies worldwide spent over three million US dollars on single particle impact breakage characterization testing in 2006."

Jan 1, 2009

By Ken Norris

"Campbell Mine which has been in continuous operation since 1949 has undergone numerous operational changes in the past 3 years. This paper describes the process changes which have occurred at the Campbell Mill since 1991. The paper discusses the engineering, construction and startup of the effluent treatment circuit, the new oxide filtering and merrill-crowe precipitation circuit, and the changes to the pressure oxidation circuit. Particular attention is paid to startup problems and solutions to these problems. A review of the benefits and results of these process changes is also discussed. Future changes are also briefly reviewed with anticipated goals and expectations.IntroductionCampbell Mine is a gold mine 100% owned and operated by Placer Dome Canada. It is located in Balmertown, Ontario which is located 300 kilometres northeast of Winnipeg, Manitoba. The Campbell Mine has been in continuous operation since 1949, producing nearly 8,000,000 ounces. In 1993 Campbell Mine is budgeted to produce 289, 750 ounces of gold at a cash cost of $157 US/ounce. Daily mill tonnage is budgeted for 1,430 tons/day but has milled as high as 1,600 tons/day on a consistent basis. Recovery in 1993 is 93.4% and is budgeted to average 94.5% in 1994.In the 1992 edition of the proceedings of the Canadian Mineral Processors conference I described the changes that were made at Campbell starting in 1989. This paper continues where the 1992 paper ended and discusses the changes to the Campbell mill since that lime. The changes to Campbell since January 1992 have been numerous with capital expenditure in the mill exceeding $14.1 million. This paper describes three primary projects since that lime: the effluent treatment project ($5.5 million), the oxide leach/filtering and merrill-crowe project ($4.6 million) and the pretreatment project ($2.81 million). The focus of this paper is to highlight the justification of each project, the design and engineering, and some of the initial operational problems and solutions applied to those problems."

Jan 1, 1994

By P. G. Roden, G. A. Maki, P. J. Fullmann

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. The paper will deal with the various aspects of the project from conception to its present state. Key Words: stacking, mobile stackers, Linatex Separators, potash mill tailings, reclaim brine ponds, settling ponds, tailings pile. IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65% solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dikes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1986

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By T. Lu

Microwaves have considerable potential as an energy source in both mineral processing and metals extraction. In this research, the utilization of microwave radiation for the heating of a gibbsite type bauxite ore was investigated. Firstly, thermogravimetric studies were performed in order to characterize the dewatering processes of the ore. Secondly, both the real and the imaginary permittivities, which are the fundamental properties that determine the interaction of microwaves with any given material, were measured for the bauxite ore as a function of temperature. The changes in the permittivities were shown to be related to the dewatering processes. Subsequently, the effects of operating variables such as processing time, sample mass, particle size, microwave power, sample bulk density and carbon and magnetite additions on the sample temperature in a microwave field were studied. The results showed that under suitable conditions the bauxite ore could be readily heated. Therefore, there is considerable potential for the application of microwaves for the heating of bauxite ores.

Jan 1, 2007

By J. E. Nesset, J. A. Finch, Rosenblum. F., S. Somot

"In a previous presentation at the CMP, evidence was shown for the formation of hydrogen sulphide (H2S) in self-heating experiments on pyrrhotite-rich samples (Somot and Finch, 2006). Oxidation of H2S is strongly exothermic leading to the proposition that H2S is playing a key role in the self-heating process. Subsequently, tests in two weathering apparatus (I and II) were run under varying oxygen levels to further examine conditions leading to self-heating. To characterise their resulting self-heating capacity the samples from the weathering tests were subjected to a modified Stage B test using the self-heating apparatus developed by Rosenblum and co-workers (Rosenblum and Spira, 1995; Rosenblum et al., 2001). Results showed highest self-heating after weathering occurs under low oxygen conditions, supporting the H2S hypothesis. It was observed that highest heating rates are not directly related to highest weight gains of samples.INTRODUCTION“Sulphides” refer to several types of minerals containing sulphur in its lowest oxidation state of - 2. Self-heating is the spontaneous heating of a material without external heat input. It is well established that some sulphides will self-heat on exposure to moisture and oxygen (Farnsworth, 1977; Good, 1977; Rosenblum et al., 2001; Wu and Li, 2005). This process is highly exothermic and if the heat generated is not dissipated, combustion may occur when the temperature reaches the ignition point of the sulphide (typically 350-400 °C). The hazards of sulphide self-heating range from handling hot material, to sulphur dioxide release, to fires. The literature documents self-heating incidents underground, on ships and trucks transporting sulphide concentrates, and in mine waste (tailing) disposal areas (Stachulak, 1990; Lukaszewski, 1969; Headley et al., 1977). Lukaszewski (1969), Farnsworth (1977), and Good (1977) note that sulphide minerals can act as fuel to promote underground mine fires. Based on such findings, sulphide minerals could become classified as hazardous materials, making transport of concentrates and storage of mine waste subject to stricter and more costly regulation. The problem is one the industry is keen to avoid."

Jan 1, 2009

By W. T. Sampson

Introduction The Kirkland Lake (Ontario) property of Wright-Hargreaves Mines, Limited, - consists of four claims. The two main shear zones or 'breaks' of the Kirkland Lake camp extend through three of these claims, for a distance of approximately 3,500 feet. These claims are on the northeast side of the original lake. The water in this section of the lake has now been replaced with mill tailings. The degree of success of any completed undertaking, especially in the mining industry, reflects the personnel involved. I state with pleasure that the successful deepening of No. 5 winze from 6,400 feet to 7,272 feet was largely due to the co-operation and skilled workmanship of Shaft Captain J. Myelde and his efficient 'leaders'. This winze was sunk at a time when it was most difficult to obtain experienced shaftmen, with the result that the crews did not wholly consist of experienced men (although their desire to learn shaft sinking soon gave good results). This condition added greatly to the responsibilities and duties of those in charge, whose first consideration was for the safety of those engaged in the work, and I take great pride in recording that the entire sinking programme was completed without a lost-time accident. Location of Winze Due to the information obtained through deep diamond-drill holes collared below the 6,000-foot level being of sufficient importance to warrant further exploration, it was decided to deepen the existing No. 5 winze rather than sink another winze. This decision meant that the sinking must be co-ordinated with and proceed simultaneously with operations in the winze, where mining was being carried on between the 3,900-foot and 5,100-foot horizons, inclusive.

Jan 1, 1948

By A. J. Monhemius

"The paper reviews the history of modern iron control processes in hydrometallurgy. Particular attention is paid to the processes developed in the 1960s by the electrolytic zinc industry for the removal of iron from zinc sulphate leach liquors - namely the Jarosite, Goethite and Hematite processes. Problems faced by the industry in the safe disposal of the iron residues produced by these processes are discussed. The lessons learnt over the past half century by the zinc industry are projected on to the current efforts to develop hydrometallurgical processes for the treatment of copper sulphide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” is doomed to ultimate failure, unless and until methods are developed that can recover iron from solution in a form that can be directly utilised by the steel or pigment industries.INTRODUCTIONYou suddenly realise that age is catching up with you and that technology is moving on apace when you are asked to talk about the history of a process or a technology that you’ve grown up with. Such was my reaction when, out of the blue, I received an email last year from the chairman of the CIM’s Historical Metallurgy Committee, asking me if I would give a talk on the early developments of iron control in hydrometallurgy. Once I’d got over the initial shock of realising that I had now become living history, I was of course flattered that the invitation was to give a talk at the prestigious IMPC, a conference series that has been going for as long as I have been in the business. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, made the invitation even more appealing and appropriate, because I was the co-chairman of the First Symposium on Iron Control, together with my old friend, John Dutrizac (known by many as Dr Jarosite), which was held 30 years ago in Toronto.first became involved with iron at the very start of my career in hydrometallurgy – the research topic for my Masters degree thesis at UBC, back in the mid 1960s, was “Reductive leaching of Goethite with SO2”. My thesis supervisor was the late Professor Ian Warren, who himself was a protégé of Professor Frank Forward, one of the founding fathers of modern hydrometallurgy. Little did I realise at that time, now 50 years ago, that the problem of iron and how to deal with it in hydrometallurgical processes would be a theme that followed me throughout much of my 40-year career in academia."

Jan 1, 2016

By F. H. Hueston, R. S. Barclay

"Depending on the application, zirconia, fused magnesia and graphite have been found to be the most suitable crucible materials for melting uranium metal and its alloys. Although graphite has been found to be satisfactory for uranium and uranium alloy castings with cross sections of 4 square inches or greater, ceramic-type molds are superior for small sections and those shaped castings which prohibit the economic use of machined graphite molds. Heating cycles, addition mechanisms and furnace conditions for melting are discussed."

Jan 1, 1967

By G. M. Brownell

Introduction The Flin Flon mine is located on the boundary line between the provinces of Manitoba and Saskatchewan at a point about four hundred miles northwest of Winnipeg. A branch of the Canadian National railway provides the town of Flin Flon with direct transportation facilities. The property was staked in 1914 and, after a considerable amount of exploration; the Hudson Bay Mining & Smelting Company was organized and brought the property into production in November, 1930 (1). Mining is carried on by open pit and underground methods at the rate of about 4,400 tons per day. Production for the year 1934 was: 99,334 ounces of gold; 1,335,319 ounces of silver; 37,486,054~pounds of copper; and 49,427,280 pounds of zinc; in addition to small amounts of cadmium and selenium. The Flin Flon deposit is one of the largest low-grade ore deposits in Canada with complete hydro-electric and metallurgical plants for the production of blister copper and electrolytic zinc. Previous Work The development of the Flin Flon mine into one of the major mining operations in Canada has created a need for a more detailed geological study of the area. Practically all of the information published to date concerns the general surface features. It is the purpose of this paper to deal more specifically with the ore-body and its relationship to the enclosing rock as revealed by studies made possible through recent underground development. The earliest published report on the area is by E. L. Bruce (2), who made a reconnaissance geological investigation of the region for the Geo-logical Survey of Canada in 1914 and established the main. petrological units. Several years later the area immediately around Flm Flon was mapped in greater detail by F. J. Alcock (3). In the summer of 1934, the area of Missi sediments to the north and east of the mine was studied by J. W. Ambrose. His report has not yet appeared in print but his findings are of importance.

Jan 1, 1935

By Don A. Toth

Until recently, the fire protection systems used to protect mining equipment were based on generically designed, off the- shelf concepts. These systems were reliant on single agent approaches and were generally comprised of a series of small twenty or thirty pound chemical canisters that would discharge their contents when triggered by thermal detection means. As the equipment grew in capacity, the logic used to increase the protection was to add more chemical canisters to the system. Hydraulic excavators and large-scale mining trucks grew dramatically in size into the 1990?s and beyond; with this growth came the increase in major losses due to fire. This was evidenced throughout this period, and continues to be of great concern today. During this presentation you will learn of the significant changes that have come about as a result of this history. Today, dual-agent products, infrared detection and unit-specific, engineered systems are the primary phrases used when discussing how to best protect this equipment from fire loss. This session is a must for anybody looking to optimally protect their equipment assets and for those looking to renew and/or secure new insurance for high value equipment in the future.

Apr 1, 2005

By G. Bridgstock, S. S. Forbes, E. M. Elkin

"OPERATIONS at Canadian Cop-per Refiners Limited, since the refinery was established in 1931, have been described in previous papers ( 1,2). Since then the refinery has treated the entire copper output of Noranda Mines Limited and Hudson Bay Mining & Smelting Company Limited. With the commencement of production in 1956 at Gaspe Copper Mines Limited, this copper has also been refined. From the start of operations to the end of 1958, the following had been refined: copper, silver, gold, selenium and tellurium.Construction of new buildings and additions to other buildings have been needed to handle increased receipts. The refining capacity has been increased from 112,000 tons of copper per year to a total of 236,000 tons per year.The refinery is located at Mont-real East, Quebec, close to railway and highway facilities. Incoming materials and shipments, with some small exceptions, are handled by rail. Some finished products are sl1ipped by industrial flatcar to the adjoining plants of Canada Wire & Cable Company Limited and Noranda Copper & Brass Limited."

Jan 1, 1960

The common theme of these four objectives is declaration. Declaration tells the compiler that an entity exists and also provides the name and nature of the entity. Since everything you create has to be declared, you must know how to declare correctly and be able to make appropriate use of all the declaration tools available to you. This objective recognizes the importance of declaration by requiring you to know everything about Java declarations Write code that declares, constructs, and initializes arrays of any base type using any of the permitted forms both for declaration and for initialization. This objective addresses your understanding of all aspects of arrays. Arrays are the simplest possible data collection and are supported by all modern programming languages. However, Java?s arrays are different from those in other languages, especially C and C++, because they are actually exotic objects. This objective recognizes the importance of being able to make use of all the functionality of arrays. You will be expected to know how to declare, construct, and initialize arrays.

May 1, 2011

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By A. H. Anderson

THE travelling grate coking process was developed by Shawinigan Chemicals, Limited, at their Shawinigan Falls plant. The first production unit went into operation a month prior to the outbreak of the war. Since then a substantial part of the coke used in the manufacture of calcium carbide has been produced by this process. In the following will be given a short account of the development work, a description of the process and the equipment, a discussion of the properties of the coke, the economics of the process and its future possibilities. EXPERIMENTAL WORK The carbide industry is a large consumer of coke, one ton of commercial carbide requiring for its production 1,200 lb. This coke must meet certain specifications in order to be acceptable. It should have a low ash content, preferably below 8 per cent, and the sulphur and phosphorus content must not be above specified limits. The size of the coke is also important. If it is too large it has to be crushed before it can be used in the furnaces, and if it is too fine it may have to be screened and briquetted. In addition, it must be dry. Although it was generally possible to purchase coke, including petroleum coke, and coke fines, in the quantities required, it became increasingly more difficult as time went on to obtain coke of a suitable quality at an attractive price. It was therefore natural for us to look to coal carbonization as a means of basing the supply of the fundamental raw material for carbide manufacture on something more solid than the shifting conditions of the coke market.

Jan 1, 1944

By Gilles Landry, Mohamed Ourriban, Pierre Pelletier, Ahmed Bouajila, Claude Gagnon

"This paper summarizes the work carried out to develop and implement the gold cyanidation by size class (CSC) process, a novel concept aiming to reduce cyanide consumption.First, the authors will present the methodology and results of laboratory tests conducted to evaluate the response and the expected gains for the selected ore when submitted to the CSC processing. In the second part, focus will be on the methodology behind the CSC scheme development prior to its implementation at Sleeping Giant Mine concentrator. Finally, the evaluation of the modified circuit performance (operating since July 2007) will be addressed as a reduction of cyanide consumption by more than 30% and of free NaCN in the tailings by more than 50% is confirmed.INTRODUCTIONCyanidation is the most widely used technique to extract gold from hard rock ore. Its use of oxygen as an oxidant still makes it the cheapest process available after more than a hundred years. Unfortunately, gold cyanidation is known to be a slow process that requires high consumption of cyanide. In fact, cyanidation plants are designed with very long residence times (Habashi, F., 1967). Drawbacks of long cyanidation times are, among others, loss of gold in tailings, high reagent consumption and high capital investment and maintenance costs.Responding to their members expectations for the improvement of cyanidation process, COREM undertook a challenging R&D program covering the development of alternative concepts (processes) and the understanding and solving of mass transfer, gold passivation and process water chemistry problems. One of the interesting findings of the R&D program is a patent pending process technology based on the cyanidation by size class (CSC) concept (Côté and Ourriban, 2004; Gagnon and Ourriban, 2007; Gagnon and Ourriban, 2004).The new technology was tested at the Sleeping Giant concentrator, a plant member of COREM. The existing flowsheet was modified in order to implement the CSC process in the full-scale plant. The plant has been operated using the modified CSC based process since August 2007. Laboratory testwork was conducted prior to the industrial application in order to properly design the new process scheme. The modifications included:1) Reclassification of the grinding circuit product through an hydrocyclone2) Leaching of the coarse size fraction3) Addition of the fine fraction to the coarse leaching circuit tails."

Jan 1, 2009