Search Documents

By M. O. Pekguleryuz, D. S. Aydin

The high temperature oxidation and ignition resistance of Mg-(0-6) wt% Nd alloys have been investigated via isothermal and continuous heating experiments conducted in air atmosphere. Alloy composition is observed to be effective in low levels (~ 0.5 %) in the ignition temperature (Ti) of the alloys; the Ti of pure Mg increased from 630 °C to 770 °C with 0.5 wt% Nd addition. However, no noteworthy improvement was achieved with further additions up to 6 wt% Nd. The initial microstructure was observed to determine the oxide structure on the surface due to the differing oxidation behavior of the phases (a-Mg + Mg12Nd intermetallics). It has been found that the formation of a Nd-depleted region at the subsurface due to extensive Nd oxidation at the oxide/intermetallic interface lowers the protective ability of the oxide scale.

Jan 1, 2015

By Viraj Parekh, Kinnor Chattopadhyay, Sina Mostaghel, Xiao Zhang

Electric arc furnace steelmaking is a dominant approach in North America and controlling EAF emissions is a key issue today because of stringent permit limits imposed by various regulatory bodies. In the present study, an attempt has been made to mathematically model EAF emissions, and use the models as a predictive tool for fine tuning the process. CFD modelling has been used to model various fume release scenarios, and optimize the exhaust conditions for maximum capture. Thermodynamic calculations have been used to analyze various chemical reactions which lead to the emissions of hazardous air pollutants with special emphasis on Zinc, Lead and Manganese.

Jan 1, 2015

By Hamid Mahmoudabadi

In the present paper, the performance of four approaches based on neural networks and geostatistical method for grade estimation are compared and analyzed their performance to find a proper method. Four methods, Multi Layer Perceptron neural network (MLP), Radial Basis Function (RBF), General Regression Neural Network (GRNN) and Ordinary Kriging (OK) are selected for ore grade estimation of variable Fe in an iron deposit located in Iran. For each method, two diagnostic statistics are calculated: Mean square error (MSE) and correlation coefficient. The results show the superiority of the General Regression Neural Network.

Oct 1, 2009

By A. Elsayed

Lightweight metals such as magnesium show potential in replacing aluminum alloy castings for engine cradles, cylinder heads and transmission cases. Unfortunately, magnesium alloys are susceptible to entrapping oxides and other impurities during casting that hinder strength and ductility. The current study examined various filter sizes and configurations with the aim of improving the mechanical properties of permanent mould cast AZ91E. The unfiltered casting had a yield strength, tensile strength and ductility of 93.3 MPa, 153.3 MPa and 2.2 % respectively and increased to 96.5 MPa, 167.0 MPa and 3.1 % with the use of a fine mesh filter within the well of the mould. The increased strength and ductility was likely due to the filtered castings containing fewer inclusions on their fracture surfaces as compared to the unfiltered castings.

Jan 1, 2011

Safe underground mine backfilling with hydraulic fill requires efficient fill drainage and stable fill retaining walls or bulkheads. If any or both the above two requirements are not satisfied, such a backfilling operation creates unsafe conditions and may lead to backfill retaining wall failures. Mine backfill retaining wall failures are always associated with economic losses, fatalities and interruption to mine production. Mining industry wants to either reduce or eliminate these fill retaining wall failures. The fill retaining wall failures could be effectively avoided through the use of fibre reinforced shotcrete fill retaining walls and engineered drainage systems through the retaining walls. This paper presents the experience of the author in developing, implementing, and monitoring several hundred fibre reinforced shotcrete fill retaining walls at a mine in Australia with the highest safety standard. The details on the mine backfill drainage system and fibre reinforced shotcrete fill retaining wall designs are also presented.

May 1, 2007

By Goutam H. Shahani

Today, the mining and mineral sectors are being impacted by highly fluctuating supply ? demand, extreme price volatility and tremendous market uncertainty on a world-wide basis. This pattern is expected to continue for the foreseeable future. In particular, large consumers of tonnage quantities of industrial gases (oxygen, nitrogen) all have to make informed investment decisions in this uncertain economic environment. Plant owners ? operators need to carefully examine their current and future industrial gas needs in order to develop the most cost-effective industrial gas plant configuration. This can be done by partnering with an experienced engineering company that offers a complete technology portfolio for producing industrial gases. Ideally, the mineral and engineering companies have to work together as a single team to identify the most efficient and economic plant design. This includes an in-depth assessment of capital and operating costs, in order to deliver an optimal solution, taking plant reliability and process safety into account. It is important to consider all the industrial gas needs at a given manufacturing complex, in conjunction with available utilities and infrastructure to develop the best possible long term solution. Oxygen (O2) requirements include: oxygen enriched and oxy-fuel combustion, smelting and hydrometallurgical operations. Nitrogen (N2) is used for annealing. All of these industrial gas requirements have to be examined at a given site over a long term horizon in a holistic manner. Cryogenic air separation was first practiced at a commercial scale in 1902. Since then, the technology has been constantly refined to reduce cost; and improve reliability and flexibility. Today, using advanced engineering techniques, including proprietary process simulation, and modern fabrication techniques, it is possible to build air separation plants that are both low cost and high quality at the same time. It is important to work with an engineering company that owns a complete portfolio of industrial gas technologies, functional engineering capabilities and a variety of plant solutions. Such a partnership can quickly identify a ?sweet spot? for a given situation. By drawing on experience gained from hundreds of projects, it is possible to quickly optimize a given requirement. In situations where a customer wants a complete solution it may be appropriate to provide an air separation plant on a turn-key basis. This will enable the mining and mineral processor to focus on their core business. By using global procurement and construction capabilities it is possible reduce cost and improve project execution, thereby making industrial gas plant procurement simpler and cheaper for the mining and mineral sector.

Nov 1, 2011

By Mika Muinonen

"Dewatering of nickel concentrate at the INCO Thompson integrated mine-metallurgical site takes place within the smelter plant. The eight original 60 foot diameter cable torque thickeners of which four were operational and eight Dorrco internal drum filters have been replaced with a single Outokumpu high rate thickener and a single Lasta pressure filter. The modernization has resulted in a filter cake which has a more stable and lower moisture content. Control of the entire dewatering process has been improved and costs have been reduced.Typical filter cake produced from the Dorrco filters during processing of high tonnages of Birchtree mine ore was ~20% moisture vs. ~13% moisture for concentrate produced from the Thompson mine ore. The high moistures were correlated with the amount of fine magnesium silicate gangue in the concentrate. As Birchtree ore processing rates have increased, this filter cake moisture became unacceptable because of material handling problems and the impact on furnace metallurgy. The Dorrco filters were replaced with the Lasta filter in 2003 that has consistently produced filter cake at ~11% moisture.This paper summarizes the piloting, design, installation and commissioning of the modernized dewatering circuit.INTRODUCTIONThe Thompson integrated nickel processing facility was built in 1958 and originally consisted of a mine-mill-smelter and, soon after, a refinery.Nickel concentrate is pumped from the mill as a dilute slurry directly to the smelter facility ~200 meters along an unheated pipe trestle. Originally, nickel concentrate was de-watered using up to 8 conventional 60-foot diameter thickeners and 8 internal vacuum drum filters."

Jan 1, 2006

By Charles Taschereau

The statements made in this presentation contain certain forward-looking statements concerning potential developments affecting the business, prospects, financial condition and other aspects of Canada Lithium Corp. The actual results of the specific items described in this presentation, and the company?s operations generally, may differ materially from what is projected in such forward-looking statements. Although such statements are based upon the best judgments of Canada Lithium Corp. management as of the date of this presentation, significant deviations in magnitude, timing and other factors may result from business risks and uncertainties including, without limitation, the Company?s dependence on third parties, general market and economic conditions, technical factors, the availability of outside capital, receipt of revenues and other factors, many of which are beyond the control of the Company. Canada Lithium Corp. disclaims any obligation to update information contained in any forward-looking statement. Toronto Stock Exchange: CLQToronto CLQOTCQX: CLQMFOTCQX: CLQMF

May 1, 2011

By M. K. Mishra, U. M. R. Karanam

Relative to slender pillars, larger size pillars exhibit improved strata control. Fly ash, though traditionally treated as a waste product, is emerging as an alternate engineering material. This paper deals with the development of a strong fly ash composite material with additives. The geotechnical properties of this fly ash composite were determined and used to trap model core pillars, which resemble squat pillars. The trapped samples were tested under uni-axial loading in the laboratory and the results showed higher load-bearing capacity of the model core pillars. The reinforced fly ash composites provide lateral confinement and exhibit improved post- failure behaviour of the model cores.

Jan 1, 2008

By D. E. M. Plaumann, B. S. Fee, R. D. Hansen, R. R. Klimpel

"The steps from experimental curiosity through to commercial product can be slow and tortuous in spite of the quality of the technological advances offered by the new development. Data generation and interpretation need to be done in lab tests as well as full-scale evaluations and, in each, the advantages of the new reagent must be clearly identifiable and measurable.The Dow Chemical Company has patented a novel new collector for the flotation of zinc. Fl (2-hexylthioethylamine hydrochloride) has several unique structural features that suggest atypical mechanisms for zinc collection. Laboratory data have demonstrated significant flexibility with respect to grade and recovery balance at dosages lower than those typically used for xanthates.In mill trials, the same phenomanon is evident - the choice between high grade and high recovery allows one to select the desired quality of zinc concentrate. One trial in particular was run over a three month timeframe and Fl gave improvements in recovery of 2.5% and a reduction in lead levels with less than 0.5% loss in grade. The dosages of other reagents in the flotation circuit were also reduced.Data demonstrating improved recovery and grade in lab trials will be discussed. Extensive data from the mill trial will illustrate how Fl works in both rougher and cleaner circuits."

Jan 1, 1990

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By M. G. Dellow, D. W. Hendriks

"In early 1988 the decision was made by Noranda Minerals Inc. to install pressure filters at the GECO mill to replace the vacuum disk filters and bunker-C fired rotary kiln dryers. Two filters were installed, one for copper concentrate and one for zinc concentrate. Completion of the project was scheduled for the third quarter of 1989. The filters were made operational in October 1989. Some work remains to be done yet on loadout conveyors for total project completion. Capital expenditures for the project have been approximately $2,700,000 to date. The paper describes the selection criteria for the filter, the installation, startup and associated problems.1. INTRODUCTIONThe filter model chosen for the project was the Verti-Press model VP-50-6(7) (Figures1 ,2 and 3) by Filtra Systems of Farmington Michigan, USA. The decision to purchase the Filtra Systems filter was based on gaining familiarity with a different, mechanically simpler pressure filter than the Larox design and to a lesser extent a necessity for repairs to the the disc filter, rotary kiln dryer system used at the GECO operation for its' copper and zinc concentrates. The fact that it is manufactured in North America was an important consideration. The same basic principles of pressure filtration as the Larox machine are used but the implementation is quite different and somewhat simplified with some interesting innovations. 2 filters were installed to allow direct and immediate comparison of the same machine on both fine and coarse materials. Copper concentrate is reground for cleaning on the flotation circuit while zinc is not. Screen analysis of composited samples of concentrates for 1988 indicated that expected copper concentrate would be approximately 66% minus 400 mesh and zinc 50% minus 400 mesh (Tables 1 & 2).The filter is composed of six horizontal chamber module layered vertically and held together in a frame by 1 O large bolts; torqued down to 4000 ft-lbs. 6 individual belts are used; each with its own drive system. The belts themselves are of a 3 piece design with a filter cloth portion, a support belt and a rubberized intermediate portion. They are held together with steel clipper lacings. A basic description (1) of the filter operation is as follows. ""The horizontal filler chamber is closed by hydraulically pressurizing seals across each end of the filter chamber to 200 psi. The feed pump then pumps slurry into the filter chamber. Suspended solids are retained on the filter belt and the filtered solution drains into a lower drip tray and flows from the filter by gravity. At the end of the filtration or feed cycle, a rubber diaphragm in the filter chamber is pressurized hydraulically to 100 psi pressure. This removes all free liquid from the filter chamber and the filter cake. After the diaphragms are retracted the filter cake is blown with compressed air to remove any residual cake moisture. The seals are then retracted and the belt is advanced to discharge the filter cakes. During the cake discharge the belts are washed with a spray header located at the drive end of the filter. The belt assemblies move one (1) complete revolution during the cake discharge cycle. The cycle automatically repeats until the filter is shut down by the operator."

Jan 1, 1990

By Marcel Labbé

La largeur de l?armature peut être modifiée selon les besoins du client entre 48 " et 64" de largeur totale, donc 2 sections de 24" à 32". Ceci permet à l?opérateur d?effectuer le démantèlement de l?équipement pour le déplacement dans les endroits restreints. Le déménagement d?un niveau à un sous-niveau devrait se faire dans un quart de travail de 8 heures. L?option de largeur permet au client de choisir un équipement adapté à son environnement de travail (1). La largeur de la table de forage peut être modifiée selon les besoins du client entre 48" et 96". Cette particularité permet une meilleure stabilité, et plus de précision dans le forage (2). Il y a 4 pattes hydrauliques à chaque coin pour la stabilisation lors de forage (3). La table de forage a 360° d?angle de forage sur 3 côtés du transporteur. La table peut sortir de chaque côté du transporteur de 40 ½" à partir du centre du transporteur pour faciliter la mise en place de la foreuse dans les endroits difficiles d?accès. La plage de forage est considérablement agrandie. Cette caractéristique qui fonctionne hydraulique, permet à l?opérateur de forer sans être obligé de changer la position du transporteur pour des changements de trous. Tous les types de foreuse peuvent être installés sur cette table de forage (4). Sa petite dimension lui permet d?accéder, par des monteries de 30" de diamètre, à des sites de travail de 2,5 mètres de hauteur et largeur. C?est un équipement adapté aux gisements filoniens. Ce genre de gisement est de moins en moins rentable pour les compagnies minières. La mécanisation des ces gisements va permettre de les rentabilisés en augmentant la productivité et la santé du travailleur, en réduisant la dilution (5). Les manettes de contrôle de la foreuse, les mouvements de la table de forage ainsi que le déplacement du transporteur ont été installés selon les recommandations d?un ergonome. Des recherches ont été effectuées par ce spécialiste sur les cas d?accident survenus avec l?utilisation de ce genre d?équipement. Il a déterminé les positions le plus confortable que l?opérateur doit prendre pour éviter les douleurs prolongées (6). Le système de roulement est composé de 4 roues pleines installées sur 4 planétaires de 9000 à 15000 livres de capacité munis chacun d?un moteur hydraulique. Des freins ont été installés sur les planétaires pour assurer la sécurité de l?opérateur et faciliter le positionnement du transporteur lors du forage. Des roues rétractables peuvent être installées pour faciliter l?accès sur rail (7). Ce transporteur peut être alimenté par une puissance électrique plutôt que par une puissance pneumatique. Cette puissance électrique est fournie par un Power Pack qui transforme l?énergie en puissance hydraulique. Ce type d?alimentation est employé lors du forage de développement, mais il peut aussi être utilisé pour le forage long trou. Cet avantage permet au client qui a un problème de pression d?air d?utiliser l?électricité. Par contre si vous utilisez l?électricité mais que dans un secteur isolé le gros courant électrique n?est pas accessible vous pouvez utiliser votre équipement en utilisant la puissance pneumatique. Le changement d?alimentation énergétique se fait facilement (8). Cet équipement est construit pour effectuer 4 types d?activités : forage de développement de niveau et sousniveau avec l?installation d?un bras porteur, forage et pose de câbles d?encrage pour soutènement de terrain, forage de production long trou et forage de monterie ascendante et descendante. L?avantage est que vous investissez dans un seul équipement au lieu de 2 ou 3. Cet avantage vous fait économiser dans votre budget d?équipement. En plus cet équipement est construit pour de dure travaux et ne contient aucun système électronique (9).

May 1, 2001

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By Paul Voigt, Mike Hourn, Glenn Stieper

Sable Zinc Kabwe Limited ("Sable") is a base metal processing plant, two kilometres south of Kabwe Town in Central Province, Zambia. The region has a rich history in mining and minerals production, being a major lead and zinc producer from the 1900s up to the mid-1990s. In 2006, a copper plant was built at the Sable processing site to treat third-party copper and cobalt oxide ores and concentrates. The oxide leaching plant included whole ore leaching, solvent extraction and production of 8,000 tpa LME Grade A copper cathode. The plant was placed on care and maintenance in 2014, and Glencore Plc ("Glencore") took the opportunity to convert the plant using a minimal budget, to an Albion Process™ plant to treat local refractory copper concentrates unsuitable or uneconomic for smelting. The Albion Process™ plant comprises an M100 IsaMill™ operating in acidic conditions such that raffinate from the downstream process is recycled back to slurry the concentrate delivered to site thus maximising copper tenor in solution and reducing water consumption. The finely ground concentrate feeds an oxidative leaching plant using the existing stainless steel oxide leach reactors converted to Albion Process™ duty by fitting HyperSparge™ supersonic oxygen injectors and gas dispersing agitators. The leached slurry is then directed to the existing solid/liquid separation equipment, and the PLS is then sent to the existing SX/EW plant. The plant also allows for cobalt recovery from the raffinate. The plant was designed based on testwork on regional copper concentrates. The plant was designed to toll treat a range of concentrates, and so the design was flexible With the flexibility of the Albion Process™ being one of its distinct advantages, the plant was ideally suited for tolling regional concentrates. The plant was commissioned and ramped up in six weeks using low-grade Zambian copper concentrate, and produced exclusively LME Grade A copper with over 99% leach recovery in the Albion circuit. INTRODUCTION The Sable Zinc Kabwe Limited ("Sable") process plant is located 2 km south of Kabwe town and 140km north of Lusaka in Central Province, Zambia. In 1902, rich deposits of zinc and lead were discovered with mines and processing plants operating in and around the town until mid-1994. In 2000, the Kabwe Mine tailings dams were sold to Sable, a newly established company, as part of a purchase deal for other plots and facilities. Up until 2004, Sable produced zinc cathodes in an SX/EW plant treating wash plant tailing material. In 2004, Sable was acquired by the South African mining company Metorex Limited ("Metorex"), and in 2006 a copper/cobalt SX/EW plant was built to produce copper cathode from malachite ore supplied from the Democratic Republic of Congo. In 2011, Jinchuan Group International Resources Co. Ltd acquired Metorex and Sable was in turn sold to a subsidiary of Glencore Plc ("Glencore").

Jan 1, 2019

By B Lumsden, B Lacouture

"Red Dog is one of the largest zinc mines in the world both in terms of reserves and annual production. In 2013, Red Dog produced 551,300 mt of contained zinc and 96,700 mt of contained lead. The mine, which is located in Northwest Alaska, is a partnership between Teck Alaska Incorporated, the operator of the mine and NANA Regional Corporation Inc, the local land owner. The Aqqaluk deposit, which is the current source of ore, has an average grade of 15.8% Zn, 4.1% Pb and 73 g/t Ag with the main minerals being sphalerite, galena, pyrite, barite and quartz. Surveys of the zinc flotation circuit at Red Dog identified that a substantial amount of fully liberated, sub 20 micron sphalerite particles were being lost to final tailings. As a means of improving fine sphalerite recovery, a four month plant trial of magnetic conditioning was conducted in the zinc retreat circuit. Magnetic conditioning technology has already been commissioned in several concentrators around the world to agglomerate fine paramagnetic minerals, increasing their probability of bubble collision and recovery in a flotation cell. The results of the four month plant trial at Red Dog showed that at a high level of confidence, a 1% increase in zinc recovery or zinc recovery and zinc concentrate grade combined was achieved with magnetic conditioning. The resulting economic benefit, which is also at a high level of confidence, is significant to Red Dog and therefore, magnetic conditioning has been permanently incorporated into the Red Dog zinc flotation circuit.IntroductionRed Dog is the largest zinc mine in North America and represents approximately 29% of North American zinc concentrate production. The mine is located in northwest Alaska, approximately 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The remote location makes the mine accessible only by air or seasonally by ocean-going barges. Red Dog is a partnership between NANA Regional Corporation Inc, the land owner and Teck Alaska Incorporated, the operator of the mine."

Jan 1, 2016

By Fred Delabbio

There are presently several issues that the mining industry is facing, such as underground air quality, deep mining and green house gas emissions, which could be addressed by the application of alternate energies. Several aspects must be considered by the industry in any drive to introduce new technologies within the context of a producing underground mine. This article presents several operational and support aspects that will evaluate the relevance of alternate energies, with emphasis on hydrogen power systems: operational drivers, commercial supply of technology, site supply system requirements, health and safety, capital and operating costs, mine production, corporate philosophy, and role of government. It is concluded that introduction of alternate energy technology requires a step-wise progression: Applicability to the industry, proof of concept testing, development of generic infrastructure, power systems and regulations, whole system studies and detailed studies of cost and risk versus benefits. The current initiative to apply fuel cells is at the proof of concept stage, entering the generic infrastructure stage.

May 1, 2007

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986