Search Documents

By Håkan Schunnesson, Kirsten Holme

"When mining high grade, narrow ore bodies, the mining method often implies a very detailed knowledge of the ore contacts to avoid unacceptable ore loss and waste rock dilution. During the past decade, the use of microprocessor based drill monitoring equipment has become an accepted technique, even for percussive drilling. On the basis of the recorded drill performance, such as penetration rate, torque pressure, thrust etc., a fast evaluation of the lithological sequence of the ore zone can be made. In order to evaluate the potential of percussive drill monitoring to pro-vide detailed information of the geometry of the ore body, the technique was tested in the Viscaria copper mine in Sweden during 1996.To provide understandable information to the mine geologist, great emphasis was placed on the separation between the drilling response generated by variations in rock conditions from variations caused by the operator and the drill system. Due to the complicated geology in Viscaria, the drilling response presented to the geologists was separated in two independent signals, one representing the hardness of the rock and one representing the in homogeneity(fracturing) of the rock. With those signals a good separation between different rock types in the ore horizon was achieved.The experience from the Viscaria copper mine is that drill monitoring not only can be used to locate contacts between rock types, but also to characterize rock conditions and, often, also to specify the exact rock type present. Because it is possible to get the drill monitoring information very quickly it is a valuable complement to diamond drilling for increasing the specific knowledge of the geology and the ore body."

Jan 1, 1997

By F. E. du Plessis

"The distinction between data suitable for process control and data subject to aliasing only becomes quantifiable with the availability of rapid real-time measurements. Expecting the dynamics of flotation to vary for different ore types, process flows and equipment types; a study was conducted to compare the dynamics of different flotation processes. The results shed light on the critical sampling intervals required for process control which in turn allows process stabilization and optimization. The technology used for the in-line measurements is based on diffuse reflective spectroscopy and has been introduced into the mineral processing industry over the past ten years. It has been widely implemented in the sulphide flotation industry in South Africa for the real-time measurement of grade.BACKGROUND AND OBJECTIVE A study was conducted by Du Plessis and Keet (2010) to quantify the minimum sample frequency required for grade and/or impurity control. The study was based on chromite data collected at 15 second intervals from the concentrate line of a flash float cell in the Platinum industry. The data captured the natural process variation of the entrained chromite through water recovery due to changes in feed parameters and flotation performance. It was found that the minimum rate of sampling required from the studied flash float concentrate was 2 minutes. This sampling interval time accounted for 90% of the variance in the process data. It was further found that a sampling interval time of longer than 4 minutes produced data with no significant correlation to reality. The dynamics of the flotation process has been misjudged in the past but can be quantified with the availability of real-time grade measurement based on diffuse reflective spectroscopy. The objective of the study was to compare the dynamics of different sulphide flotation processes through the comparison of maximum sampling interval times required to combat aliasing. All data were collected from single stream analyzers that are currently installed at mineral concentrators. The technology used is based on diffuse reflective spectroscopy."

Jan 1, 2012

By Richard W. Hutchinson, Robert W. Hodder

"Pyritic massive sulphide deposits lie conformably above submarine volcanic rocks, and beneath siliceous and manganiferous iron formations. The massive bodies are often zoned, with a barren pyritic top grading downward into pyrite with sphalerite, and occasionally galena, and a chalcopyrite-rich base. They are frequently brecciated, like the lavas beneath them, which contain pyrite and chalcopyrite as coatings on joints and fractures and as dispersed grains. The lavas also exhibit propylitic, argillic and silicic alteration. These sulphide deposits appear to have formed on sea bottom from fluids escaping through the lavas during periods of exhalative and sometimes explosive volcanism. The process may be comparable to the present deposition of base metals from hot brines in the Red Sea. Some porphyry copper deposits resemble the altered, sulphide-impregnated lavas which lie beneath bodies of pyritic massive sulphide. In porphyry copper deposits, pyrite and chalcopyrite occur as veinlets and dispersed grains in intensely fractured tuffs, flows, sub-volcanic intrusions or other host rocks, characterized by propylitic, argillic and silicic alteration. Metal zoning is present; sphalerite and galena often occur in manganiferous veins peripheral to a shell of pyritic veinlets which encloses the mineable zone of chalcopyrite-bearing veinlets. This sulphide distribution appears to have formed from hydrothermal fluids escaping, either passively or violently, from solidifying magma. The fluids may be comparable to hot brines encountered by drilling in the Salton Sea area of California.There are also important differences between massive sulphide and porphyry copper deposits. The former usually occur in differentiated, mafic-to-felsic subaqueous volcanic rocks, whereas porphyry copper deposits are often associated with shallow plutons and subaerial volcanic rocks of intermediate to felsic composition. Calcic-sodic metasomatism accompanies the massive sulphides, whereas potassic metasomatism characterizes the porphyry cop.per deposits. Further, ages of massive sulphides range from Archean (Keewatin) to Tertiary, but porphyry coppers are Triassic to Tertiary in age. These similarities and differences suggest that massive sulphide and porphyry copper deposits are related tectonically and metallogenetically. The former were generated during early stages of crustal evolution, particularly in Archean time, and were repeatedly derived during early stages of younger, individual tectonic cycles. In contrast, the porphyry coppers developed during the later stages of crustal evolution - later in terms of both absolute age and relative age within younger individual tectonic cycles. They appear in younger rocks generally, and specifically in rocks involved in events of the middle and late tectonic stages of orogenic belts. The massive sulphide deposits are of early-magmatic eugeosynclinal affiliation, whereas the porphyry deposits formed in late-magmatic, predominantly subvolcanic settings at the edge of continental plates, where contemporaneous exhalative volcanism was mainly a subaerial phenomenon. Transitional types of deposits exist and are found on continental margins with flanking eugeosynclinal sequences."

Jan 1, 1972

By H. Reimer

The rates of return on investment are examined for several major Canadian mining companies. Because we are dealing with a highly cyclical industry, subjected to widely fluctuating metal prices, rates of return are examined over a 20-year period. Conveniently, the first decade examined reflects the period when the industry enjoyed incentives to develop deposits; during the second decade, incentives were reduced and the industry became the most heavily taxed industry in Canada. The high rates of inflation since 1973 have distorted the real rates of return on investment if one considers replacement cost.

Jan 1, 1977

By J. M. Wolverton

CONSIDERABLE interest has always been taken in Safety-First and First Aid at the Sullivan mine. Even during the early days of development, Safety-First committees periodically held meetings, while lectures in first aid were given to any employees interested in the work. In 1929, a Safety Department was organized, and all accident-prevention and first-aid work was put in charge of a full-time Safety Engineer. An extensive programme has gradually been developed, the value of which can best be indicated by the reduction of the accident rate from 18.4 shifts lost per 1,000 shifts worked for non-fatal accidents and two fatalities for 1927, to 3.24 shifts lost per 1,000 shifts worked and no fatalities for 1936. SUPERVISION All work connected with accident prevention or first aid is under the jurisdiction of a central committee, known as the Accident Prevention Committee, which meets regularly once a month. It consists of all superintendents, department heads, foremen, and shift bosses, and is presided over by the Safety Engineer. At these meetings, the accident records of the previous month are reviewed and all accidents carefully analyzed and discussed. All proposed changes in the safety rules or in the accident tprevention programme are taken up and passed upon. Complaints or suggestions from the Safety-First Committee and the Employees Co-operative Committee, dealing with safety, are discussed and passed upon or a subcommittee is appointed to investigate and take any action found advisable. The question of underground ventilation and dust control, which recently has become a very important problem, always receives considerable attention.

Jan 1, 1937

By Martin Grenon

This paper presents two case studies where fracture set orientation was quantified using three methods: a simple fracture pole grouping, a Fisher distribution and a Kent distribution. The three fracture orientation representations were then used as inputs for kinematic slope stability analysis. Differences showed up in the probability of sliding for all instability modes considered.

Aug 1, 2013

By K. Muehlenbachs, J. U. Stemler

"Abstract - The Boston deposit is a recently discovered Archean lode-gold deposit located approximately 700 km northeast of Yellowknife, in the southern portion of the Hope Bay volcanic belt. Primary H2O-CO2-NaCl fluid inclusions associated with gold mineralization at Boston are of low salinity (4.6 ± 1.4 eq. wt.% NaCl, n = 182) and contain pure CO2. Homogenization temperatures of liquid-phase inclusions average 270° ± 33°C (n = 141), but some fluid inclusion assemblages contain coexisting liquid- and vapor-phase inclusions that homogenize near critical conditions, suggesting phase separation. In these groups, liquid-phase inclusions homogenized at 299° ± 25°C (n = 24), and vapor-phase inclusions homogenized at 338° ± 28°C (n = 18). These temperatures overlap within error, and a median temperature of ~320°C is taken as representative of trapping conditions within the veins. An approximate pressure of 2-3 kbar was estimated from fluid inclusion isochores at this temperature. Stable isotopic compositions of carbonate minerals from the mineralized zones range from -4.7‰ to -3.1‰ in d13C, and from 11.2‰ to 12.8‰ in d18O; quartz ranges from d18O = 12.8‰ to 14.9‰; and pyrite ranges from d34S = 2.1‰ to 3.5‰. The d18OH2O, d13CCO2, and d34SH2S values of the fluid calculated from these minerals at 320°C are 6‰-9‰, -2.4‰ ± 0.6‰, and 1.5‰ ± 0.5‰, respectively, and are intermediate between metamorphic and magmatic compositions. A unique source for the fluids cannot, therefore, be constrained from these data. Petrographic and geochemical data for the Boston deposit are consistent with data from other Archean lode-gold deposits worldwide, implying that the Boston deposit formed in a similar environment and from similar types of fluids. These results suggest that the Hope Bay volcanic belt may represent a major new mesothermal gold belt in this part of Nunavut. Sommaire - Le gîte Boston a été récemment découvert à environ 700 km au nord-est de Yellowknife dans la partie sud de la ceinture volcanique de Hope Bay, il s’agit d’un gîte d’or filonien d’âge Archéen. Les inclusions fluides primaires de H2O-CO2-NaCl associées à la minéralisation aurifère du gîte Boston présentent une faible salinité (4.6 ± 1.4 eq. pds.% NaCl, n = 182) et contiennent du CO2 pur. La température d’homogénéisation des inclusions à phase liquide est en moyenne de 270° ± 33°C (n = 141), mais certains assemblages d’inclusions contiennent des phases liquides et gazeuses coexistantes qui s’homogénéisent dans des conditions quasi critiques, suggérant qu’elles résultent d’une séparation de phase. Dans ces groupes, les inclusions de phase liquide s’homogénéisent à 299° ± 25°C (n = 24) et les inclusions de phase gazeuse s’homogénéisent à 338° ± 28°C (n = 18). Ces températures se recoupent à l’intérieur des limites de l'erreur de mesure, et nous considérons qu’une température médiane de ~320°C est représentative des conditions de piégeage dans ces veines. Les isochores permettent d’estimer une pression d’environ 2-3 kbar à cette température. La composition des isotopes stables des carbonates dans les zones minéralisées s’étend de -4.7‰ to -3.1‰ pour d13C et pour de 11.2‰ à 12.8‰ pour d18O; les valeurs de d18O pour le quartz varient de 12.8‰ à 14.9; et les valeurs de d34S dans la pyrite vont de 2.1‰ à 3.5‰. Les valeurs de d18OH2O, d13CCO2, et d34SH2S du fluide calculé à partir de ces minéraux à une température de 320°C est de 6-9‰, -2.4‰ ± 0.6‰, et 1.5‰ ± 0.5‰ respectivement, reflétant des conditions intermédiaires entre des compositions métamorphiques et magmatiques. Il n’est donc pas possible d’identifier une source unique pour ces fluides à partir de ces données. Les données pétrographiques et géochimiques du gîte Boston sont similaires à celles d’autres gîtes d’or filoniens ailleurs dans le monde, ce qui implique que le gîte Boston s’est formé dans un environnement similaire à partir des mêmes types de fluides. Ces résultats suggèrent que la ceinture volcanique de Hope"

Jan 1, 2006

By G. K. Herzog

THE problems relating to the construction and use o{ mining equipment are basically the same as those pertaining to equipment in other industries. It is true that much mining equipment is subjected to an unusually severe combination of shock, high stresses, abrasive wear, and corrosive ? conditions, but in other industries, also, equipment must operate under similar adverse conditions, so that their experiences may readily be applied to the problems of the mining industry. Steel and iron are for obvious reasons the most suitable materials for the construction of the greater part of the equipment used in the mining industry. For a large percentage of uses, the ordinary plain carbon-steels and ordinary or unalloyed cast-iron are, and probably will continue to be for a long rime, entirely satisfactory materials. There are, however, many. conditions which cannot be satisfactorily taken care of by these materials, and alloy steels and irons must be used where the greatest possible economy is desired. In general, alloy steels and irons are used where it is necessary or economically desirable to use materials possessing properties superior to plain carbon-steel or ordinary cast-irons, such as: (a) better strength (b) better wear resistance (c) better corrosion resistance (d) better resistance to high temperatures (e) better resistance to low temperatures or combinations of two or more of these advantages. There are also conditions where materials having other special properties are required, such as, for example, certain magnetic or electrical properties for electrical machinery; but in the great majority of cases, one or more of the five advantages listed are the most desired.

Jan 1, 1938

By J. R. D. Gravel, D. A. Poland

"The induration of iron ore pellets has always utilized prefired pellets to protect the pallet cars from the environment of the induration furnace. This paper presents the process used to obtain superior upper sidewalls. These heat resistant castings are used on induration pallet cars, and their life improvements by as much as 400% is a significant step towards the reduction of the prefired (or hearth layer pellets.) The benefit to the industry in the removal of the hearth layer is improved overall productivity. IntroductionThe Iron Ore Company of Canada (IOC) operates with production facilities located in Labrador City, Newfoundland and Sept Iles, Quebec. It has recently been acquired by North Limited, an Australian based resource oriented company. Prior to its acquisition, IOC has examined several methods of operational cost reductions. One of these was an examination of indurrating pallets. Pallets are composed of numerous assemblies and sub-assemblies. The examination of the upper sidewalls began as an intent to increase the operational life of the component. The anticipated net effect was to be a reduction in the overall pallet maintenance cost. All of the components and assemblies have undergone a severe scrutiny. IOC has found that the success of the project has depended upon not only the technical competency of all parties involved, but also upon the ability to share risk, to be innovative, and to find a partner with whom the development can proceed without fear and yet with accountability. IOC has found in Cast Steel Products (CSP) such a partner in the field of pallet development. This paper will undertake to explore the progression into the arena of partnering between IOC and CSP. CSP and IOC met in the fall of 1994. The work of re-engineering the pallets began with an initial order for 36 pallets in March, 1995. The work on the upper sidewalls involved segregation of the effect of alloy development versus physical geometry development. The nature of partnering between the two companies allocated alloy development to IOC and physical geometry development to CSP, yet no advancements were made in either area without the close co-operation or the involvement of both partners."

Jan 1, 1999

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By J. A. Finch

In this paper, the author offers a personal view of what the next 30 years holds for mineral processing. Restating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining ?mineral processing ?extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro- and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but this author anticipates that the new lines will come from the waste management business. The paper concludes with the examination of the “research cycle” and identification of growth in small “high tech” companies and university research centres

Jan 1, 1998

By S. Banisi, J. Marois, A. R. Laplante

"This paper compares the behaviour of gold and ore in the grinding circuit of Hemlo Gold Ltd. Particular attention is given to grinding kinetics, classification behaviour, and liberation. For grinding kinetics, laboratory grinding of gold flakes and silica, 840-1200 um in size (14/20 mesh), was also performed to provide a standard for comparison and to study in a controlled environment the mechanisms of breakage, folding, smearing and impacting.Grinding kinetics were characterized at laboratory scale with breakage and selection functions. The breakage function showed that 75% of gold disappearing from the 840-1200 um class reported to the 600-840 um; this figure is much higher than for silica ( 46%) or most other minerals, and implies that comparatively fewer fine fragments are produced from the breakage of gold flakes, on account of gold's malleability. The selection function of silica was four times that of gold. At plant scale, the ratio of the selection function of ore and gold increased from 6 for at 50-100 um to 20 at 500-1000 um.Observation of original flakes and their fragments with the scanning electron microscope showed that the main mechanism of ""grinding"" from the 840-1200 um to the 600-840 um class was folding rather than actual breakage. This was confirmed by a measure of individual flake weight. The postulated breakage cycle is that relatively globular flakes become increasingly serrated through grinding; they can then regain their original shape through folding and reflattening into cylindrical and spherical shapes, as the majority does; however, some fragments will at this point undergo actual breakage. Photographic evidence is presented to support the proposed mechanisms.Smearing of gold unto silica was observed when silica was ground after a gold, and embedding of silica into gold flakes when gold was ground after a silica. Both mechanisms occur whenever gold and harder minerals are jointly ground, and result in ""unliberation"" of gold. It is postulated that smearing of gold onto other minerals plays an important role in explaining how gravity recovery can increase overall gold metallurgy, especially when used ahead of flotation.Classification of gold in the primary hydrocyclones takes place at a much finer cut-size than ore, 20 vs. 57 um. This and the slower grinding kinetics result in high gold circulating loads in the primary loop, 6700%, and a gold content in the primary cyclone underflow (PCUF) is twenty four times that of the ore. The gold size distribution for primary cyclone overflow is much finer than that of the ore, although they are essentially similar in the PCUF.Liberation, or more accurately ""gravity recoverability"", was assessed with a 7.5 cm (3"") Knelson concentrator. It varied between the thirties for the primary mill discharge and two cyclone overflows, to highs of 89 to 92% for the PCUF and secondary mill discharge, 89 and 92%, respectfully."

Jan 1, 1991

By James D. Bittner

Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. The environmentally friendly process can eliminate wet processing and required drying of the final material. The process requires little if any pre-treatment of the material other than grinding and operates at high capacity ? up to 45 tonnes per hour by a compact machine. Energy consumption is low, approximately 1 kWh/tonnes of material processed. Since the only potential emission of the process is dust, permitting is typically relatively easy. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs. The triboelectric particle charging is effective for a wide range of materials and only requires particle ? particle contact. The small gap, high electric field, counter current flow, vigorous particle-particle agitation and self-cleaning action of the belt on the electrodes are the critical features of the ST separator. The high efficiency multi-stage separation through charging / recharging and internal recycle results in far superior separations and is effective on fine materials that cannot be separated at all by the conventional electrostatic techniques. Since 1995, this triboelectric process has been extensively used for the beneficiation of coal fly ash with eighteen separators in place and over 100 machine-years of operation at locations in the US and Europe. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash.

Nov 1, 2011

By M. P. Hay

"For a model to be successful it must address the concerns and needs of a target audience. Further, the model must demonstrate the same patterns of behaviour as the real system, and need only be complex enough to meet this objective. If the model is too complex it can become unusable to those who need it most.With this in mind, SUPASIM has been developed for the practical metallurgist requiring only laboratory flotation rate data as input. Some 35+ successful plant simulations have been completed since 1985. The approach of SUPASIM is to characterise an ore, organise information in an understandable way and add structure to the complex flotation situation and hence support the metallurgist to interpret the relationship between variables and optimise the flotation process.The paper describes the basis on which the model was developed and sets out to provide an insight into interpreting laboratory flotation kinetics and their physical meaning in a production plant and the influence floatable gangue has on float performance and plant design. A case study illustrates how the ratio of slow floating mineral to gangue can influence circuit design and improve recovery on a plant scale.INTRODUCTIONThere is an enormous amount of useful data in the results of a laboratory scale rate test. Each variable of fraction and rate, for mineral, metal and gangue has a physical meaning in the plant. The link between float kinetics and the plant in respect of recovery, grade, pulp density, pulp flowrate, residence time, number of stages of cleaning and circuit configuration has been established by the author in the process of developing SUPASIM."

Jan 1, 2005

By M. C. Bétournay

Hydrogen fuel cells are a known technology, having been applied to stationary (e.g. equipment, buildings, and power plants) and vehicle applications (e.g. transit buses and space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and greenhouse gas emissions. To date, however, fuel cells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuel cells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuel cell type of choice for the industry, the proton exchange membrane, would function at the range of surface operations, and use hydrogen that is stored under low pressure and risk. A small fuel cell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, Inco, the Ontario Ministry of Labour, Sandia National laboratories, and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter, as well as from shock and vibration provided to the unit in underground conditions at Inco?s 175 Orebody minesite and Stobie mine. The test results provided will show that the unit was not affected by the underground conditions; physically and electrically, the unit performed without any reduction in operation or adverse effects imposed

May 1, 2005

By G. Bonnell, W. Lidkea, M. C. Bétournay, E. Edwardson

"Hydrogen fuel cells are a known technology, having been applied to stationary (e.g equipment, buildings, and power plants) and vehicle applications (e.g transit buses and space shuttles). There is currently a growing need to provide alternate power systems to diesel fuel for underground mining vehicles to improve underground air quality and reduce production costs and greenhouse gas emissions.To date, however, fuel cells have not been exposed to underground mine air and physical conditions. A testing program was carried out to provide information on the vulnerabilities of fuel cells as part of a number of proof-of-concept projects to apply hydrogen power to underground mining vehicles. The fuel cell type of choice for the industry, the proton exchange membrane, would function at the range of temperatures encountered in underground and surface operations, and use hydrogen that is stored under low pressure and risk.A small fuel cell stack was tested in a cooperative project between CANMET, the Fuelcell Propulsion Institute, Inco, the Ontario Ministry of Labour, Sandia National laboratories, and H-Power. This article will review the tests carried out to measure the effects from high humidity, mineral dust, diesel emission gasses and diesel particulate matter, as well as from shock and vibration provided to the unit in underground conditions at Inco’s 175 Orebody minesite and Stobie mine. The test results provided will show that the unit was not affected by the underground conditions; physically and electrically, the unit performed without any reduction in operation or adverse effects imposed."

Jan 1, 2005

By J. E. Scott, L. M. Heaman, R. A. Creaser, G. S. Salazar

"Schaft Creek is a calc-alkaline porphyry Cu-Mo-(Au) deposit located in northwestern British Columbia. The deposit formed in a volcanic arc setting, likely on a back-arc rifted continental fragment. It is hosted by Late Triassic basaltic to andesitic volcanic rocks of the Stuhini Group (Stikine Terrane), and is associated with porphyritic granodiorite dikes emanating from the nearby Hickman batholith. The age of the Hickman batholith is approximately constrained here by a composite U-Pb zircon date of 222.1 ± 9.6 Ma, which is in broad agreement with a well-constrained age for mineralization at Schaft Creek of 222.0 ± 0.8 Ma (Re-Os molybdenite). The deposit is in most respects typical of calc-alkaline porphyry systems, but displays silica-poor sericite-chlorite alteration in mafic country rocks in place of classic phyllic altera¬tion. The deposit comprises three distinct, but related, zones: the northern Paramount zone, the Main zone, and the West Breccia zone. Two phases of mineralization are observed. The first phase occurs as hydro-thermal veins and breccias, and minor disseminations. It consists of bornite, chalcopyrite, molybdenite, and pyrite with potassic and sericite-chlorite alteration. The second phase is minor and consists of veins of molybdenite ± specularite, as well as Cu-Pb-Zn sulfide veins without any significant corresponding alteration. Extensive structural modification has affected the deposit both during and after its formation.Schaft Creek est un gîte porphyrique de Cu-Mo-(Au) calco-alkalin situé dans le nord-ouest de la Colombie Britannique. Ce gîte s’est formé dans environnement d’arc volcanique, probablement situé sur un fragment continental bordé par un bassin d’arrière-arc. Le gîte est encaissé par les roches volcaniques basaltiques à andésitiques du Groupe de Stuhini (Terrane de Stikine) d’âge Triasique tardif, et est associé à des dykes de granodiorite porphyrique provenant du batholithe de Hickman avoisinant. L’âge du batholithe de Hickman est estimé par un âge U-Pb composite sur zircon de 222.1 ± 9.6 Ma, lequel est grossièrement en accord avec l’âge de la minéralisation de Schaft Creek, estimé a 222.0 ± 0.8 Ma (Re-Os sur molybdénite).Ce gisement, bien qu’à plusieurs égards typique des systèmes porphyriques calco-alcalins, présente une altération en séricite-chlorite pauvre en silice dans l’encaissant mafique a la place de l’altération phyllique classique. Ce gîte comprend trois zones distinctes bien que connexes : la zone Paramount au Nord, la zone Principale et la zone West Breccia. Deux phases de minéralisation sont observées. La première phase se présente sous forme de veines et de brèches hydrothermales ainsi qu’en disséminations mineures et consiste en bornite, en chalcopyrite, en molybdénite et en pyrite avec une altération potassique et en séricite-chlorite. La seconde phase est mineure et consiste en veines de molybdénite ± spécularite ainsi qu’en veines de sulfures de Cu-Pb-Zn sans association à une altération particulière. Le gisement a été profondément modifié par la déformation a la fois durant et après sa formation."

Jan 1, 2008

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By N. Bahrani

Photogrammetry surveys were used to document a footwall slab failure that occurred at a surface coal mine located on the eastern slope of the Rocky Mountains. Photographs taken before and after the failure provided the pre- and post-failure geometry of the slope and the failed slab. A 2D finite element model was constructed using slope profiles. The model contained joint elements that represented the bedding surface upon which the slab slid and the model was used to analyze the footwall slope. The in situ stresses, rock properties and the bedding surface shear strength and stiffness properties are discussed. The process of mining out a valley and exposing a highwall was modelled. As expected, elastic valley rebound occurred in the model, but shear stress and shear displacement reversals along the slip surface were also observed. The modelling results provided new insight into shear strength degradation that occurs when the pit floor approaches and then passes a specific point in the highwall.

Jan 1, 2009

By B. R. Boardman

Project Environmental Approval is a multi-faceted issue. From a mining perspective, it is a costly item because of avoidable time delay. The government perspective is that the approvals are a necessary part of meeting departmental requirements to ensure that the wellbeing of other uses of the environment is maintained. This paper outlines some of the problems inherent in the environmental approvals process and makes recommendations to both the proponent and government about improving the efficiency of the process.

Jan 1, 1978