Search Documents

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

Rather like the mythical "Economic Man" "an employer" in this context must necessarily be an abstraction, and the views possessed by such an abstraction, a composite of many views known to have been expressed. Not even the complex Conciliation and Arbitration legislation in this country provides any helpful specifications, except in one peculiar particular. The Australian Conciliation and Arbitration Act provides an almost totally tautological definition, except in that one oddity referred to above. It is this : "An employer means any employer in any industry, and includes any person who is usually an employer in an industry, and also includes a Club." No doubt there is some perfectly justifiable reason for such specific and unique particularity in an otherwise meaning- less definition. That need not trouble us in this exercise.

Jan 1, 1982

Ultrasonic Extinction for High Resolution Particle Size and Concentration Analysis

Sep 13, 2010

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

The application of biogeochemical methods in mineral exploration in semi-arid to arid environments in Western Australia has been investigated in an area near Norseman.The study involved a comparison of trace element characteristics of rock, soil and plants in the vicinity of the Pioneer BB prospect, where nickel-iron sulphide mineralization occurs in a "greenstone" sequence of ultrabasic, basic and sedimentary rocks.Analyses of unweathered and partly weathered rock from diamond drill cores show the ultrabasic rock to be highly variable with respect to Ni, Cu, Co, Zn and Mn.Samples of weathered bedrock and overlying soil were analysed for total trace element contents and for the trace elements associated with secondary iron and manganese oxides. Approximately 30 per cent of the total nickel content of the weathered basic rock is associated with secondary iron and manganese oxides, compared with approximately 15 per cent in the weathered ultrabasic rock.The soil has a sufficient residual content to provide a reliable indication of the chemistry of the underlying rock. Total trace element analyses of the -89 mesh fraction show strong anomalies for nickel and copper over the mineralized zone. Important amounts of nickel, cobalt and, to a lesser extent, copper are apparently associated with secondary iron and manganese oxides in the soil.Melaleuca sheathiana (tea tree) has been used to study the relationship between soil and plant chemistry. No strong relationship between plant and rock type was observed. Analyses were made of leaves, twigs, wood, bark and roots, and all plant organs were found to have anomalous nickel and copper contents near the mineralized zone. Leaves were found to give the best contrast in the anomalous area and to show fewer erratic values than other organs. It is concluded that the uptake of trace elements by tea tree is low in the semi-arid to arid environment of Western Australia, but that analyses of the plants do reflect the presence of mineralization.

Jan 1, 1973

A commercial Philips X-ray Fluorescence (X.R.F.) analyser was converted to an experimental instrument suitable for determination of the accuracy to be expected of X.R.F. on line analyses of concentrator slurries. Problems with stability of slurry sample presentation were eliminated by a number of minor modifications.By the use of multiple linear regression techniques instrument calibration equations including error terms were determined for copper flotation feed slurries. Results indicated that the accuracy of copper and iron analyses of flowing slurry samples could approach that of static pressed powder samples.Possible means of reducing the error terms to a level of at least that of pressed powdel' samples involve alternative methods of compensating for the per cent solids in the slurry, Design is under way for installation of a plant unit.

Jan 1, 1968

Australia is not capitalizing on the raw gems and precious minerals that it produces in abundance. In particular, there is an unrealised value for diamonds due to lack of processing after mining. Australia could enhance the value of its raw jewellery products by developing and integrated jewellery industry. For instance, initiation of a diamond industry would require training programmes to educate people in the requisite skills, such as diamond sorting, cleaving, sawing, bruting and polishing. Equally important would be the training of people in design jewellery, manufacturing, and appropriate diamond grading and sales techniques. Future technological advances in diamond processing will decide where the major diamond processing centres of the world will be. Australia, for a relatively small investment, could develop a highly productive diamond processing capacity using the new technology available. Australia's geographical position, and advanced banking and communication facilities provide the potential for this country to become a major trading centre for diamonds. KEYWORDS: Argyle Diamond Mine, Diamonds, Diamond Production, Diamond Sorting, Jewellery Industry

Jan 1, 1989

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By R L. Brathwaite

The mesothermal quartz-scheelite lodes of the Wakamarina valley are one of twelve known mined or prospected gold-bearing areas in the Marlborough Schist. Recorded production was 556 kg gold, a little silver, and c. 390 t scheelite. 134 m of the 1800 m long Golden Bar reef are accessible in the No 2 level of the Golden Bar mine. The reef is a typical multi-banded mesothermal vein, mostly c. 1.75 m wide, enclosing narrow horses of schist country rock. Scheelite is sparsely distributed, and is more common in small veinlets in the hanging wall schist. The country rocks are textural zone I-1m schists of prehnite-pumpellyite to pumpellyite-actinolite metamorphic facies. Their geochemistry suggests they are part of the Caples Terrane, and of calc-alkaline volcanogenic arc origin. The associated Wakamarina Quartzite is strongly recumbent folded, and of the same metamorphic grade, with abundant pumpellyite, stilpnomelane, and garnet, presumably spessartine. Although it has geochemical signatures of a deep sea sediment, it is depleted in Cr and Cu, and greatly enhanced in K and Ti, when compared with a standard chert. It also has trace element characteristics of a calc-alkaline arc-related sediment. However, associated greenschist has MORB-like incompatible element chemistry. The Golden Bar reef lies within a steeply dipping, normal to transtensional dip-slip fault adjacent to a shallow-dipping mylonite shear zone, which, at least on the footwall side, is 040 m wide. The shear foliation has been severely dragged down to nearly parallel the Golden Bar reef within 1 m of the quartz lode. Preliminary structural analysis suggests that the shear zone is extensional. X-ray diffraction analyses of the wall rocks show a progressive depletion of amphibole, stilpnomelane, and pumpellyite towards the reef, and enhanced illite/muscovite and Kfeldspar adjacent to the lode, along with possible graphitic carbon within 10m. Two zones of intense quartz veining occur, one adjacent to the hanging wall for 12 m and one from 40 m outwards. Quartz vein systems in the country rock are complex and span from pre-schistosity to post-mylonite. They include multiple generations of quartz, actinolite, stilpnomelane, pumpellyite, albite, adularia, chlorites, illite/muscovite, calcite, and scheelite. Metal analyses across the Golden Bar reef showed gold values of 0.13.1 ppm, and low tungsten values, consistent with the observed sporadic scheelite occurrences. As and Sb are at background levels, but enhanced Cr (150 - 430 ppm) relative to the schists (30 - 41 ppm) suggests that the source hydrothermal fluids passed through and leached mafic to ultramafic rocks.

Jan 1, 1994

By T M. Brettell, D Sidea

The CSA Mine is located in Cobar, New South Wales and is operated by Glencore. Large scale underground production started from 1965, with zinc, lead, silver and copper extracted in the past. The current operations focus on copper, with a silver co-product.From 2014 to 2016, Cobar Management Pty Ltd (CMPL) undertook a major capital project to upgrade the primary ventilation system at the CSA Mine. This involved the development of ten raises using full-face raise boring from surface to a depth of 1450 m. The total length of the raises was approximately 2500 m. Geotechnical conditions were identified as a key project risk during the early planning stages of the project. Timely quantification of the geotechnical risks was required to minimise project delays and cost overruns. Geotechnical investigations were planned and conducted for each raise prior to pilot drilling and full-face back reaming.Nine of the ten raises had final wall camera and laser baseline surveys completed following full-face reaming. The surveys were conducted progressively, allowing ongoing back analysis and calibration of geotechnical evaluations as the project advanced.This paper presents the design and planning process of the raise bored excavations. It details the geotechnical investigation work undertaken to mitigate the geotechnical risks and the challenges and learnings from the project including the benefits of close collaboration between the parties involved.CITATION:Sidea, D and Brettell, T M, 2017. The CSA ventilation upgrade – geotechnical challenges and learnings, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 341–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Sheng-Hui X

This paper introduces a new coal-based rotary kiln process of DRI production - the CRIMM process, which is developed by Changsha Research Institute of Mining and Metallurgy in the past years. Its main features are the use of composite pellets (in rotary kiln). The process consists of preparation of pellets from iron concentrate and coating of coal on their surfaces. The new process is able to overcome a series of defects of the conventional coal-based rotary kiln processes. A continuous test was conducted using an experiment rotary kiln (-0.6;, x 3 m). TFe of the magnetic iron concentrate used in the test is 67.25 per cent. TFe of the product DRI is 88.54 per cent, MFe is 84.11 per cent, S and P are less than 0.02 per cent. The metallisation ratio of pellet is 95 per cent. The pellet power ratio is less than 0.3 per cent. The utilisation coefficient of rotary kiln is 1.3 t/m'-d. The overall recovery of iron concentrates is 99.7 per cent. Two small industrial plants using the CRIMM process are being set up in China. Their coal consumption can be decreased to 520 kg standard coal per ton DRI respectively.

Jan 1, 1999

By J Li, H Hooi, D Payne

Caval Ridge Mine (CVM) is one of the newly established open-cut coal mines of BHP in Queensland, where no tailings dam is planned to be built in order to minimise environmental impacts from mining activities. The waste streams from the Coal Handling and Processing Plant, including fine tailings dewatered by belt filter presses, coarse rejects, and mixed plant rejects, are co-disposed within waste dumps built with pre-strip and dragline spoils. Due to high rejects output (35 – 60% of feed) and low spoil to reject ratio (< 5) the large quantities of rejects bring significant geotechnical and operational challenges to CVM, which are exacerbated by increasing annual production rates and additional rejects from washing coal from an adjacent mine. Further in-house geotechnical review commenced in mid-2014 based on the initial geotechnical studies during the project stage of CVM between 2011 and 2013. The outcomes have enabled rejects disposal at CVM by constructing large belt filtered tailings cells, coarse rejects only dumps, and co-disposal of the mixed plant rejects at dump tip-heads. This paper presents the rejects disposal strategies at CVM from both technical and operational aspects. It also discusses future projects for belt filtered tailings moisture reduction including assessment of tailings clay mineralogy, as well as mixed plant reject co-disposal verification and optimisation.CITATION:Li, J, Payne, D and Hooi, H, 2018. Plant rejects disposal strategies applied at Caval Ridge open cut coal mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 50–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Craw, I M. Turnbull, R J. Norris, N Mortimer

The Otago Schist is being subdivided on a regional scale into structurally, metamorphically and lithologically distinct blocks. Differences between blocks are subtle, and difficult to map in the field. Boundaries are late-metamorphic or immediately post-metamorphic in origin, and are different from later brittle faults which disrupt the schist. Mapping of late-post-metamorphic structural discontinuities has direct application for basic grassroots exploration in the Otago Schist. The mineralised (and currently mined) Hyde-Macraes Shear Zone forms a regional scale boundary between a block dominated by politic schist and a block with massive psammitic schist, pelitic schist, and minor greenschist and chert. The HMSZ forms a metamorphic discontinuity, with garnet and biotite in the underlying schist, and neither index minerals apparent in the overlying schist. The HMSZ is also a structural boundary between domains with differing lineation orientations. The HMSZ can not yet be traced along strike to the northwest to the Rock and Pillar Range, where the only major discontinuities recognised are the Caples-Torlesse boundary and a normal fault separating low grade from high grade schist. Structural and lithological discontinuities in the Dunstan Range break the range up into distinct structural blocks, two of which are separated by the gold-mineralised Rise and Shine Shear Zone.

Jan 1, 1999

By Woodcock J. T

When an aqueous suspension of pyrite and manganese ore reacts with oxygen, manganese is dissolved by the ferrous sulphate and sulphuric acid produced by the oxidation of pyrite. The kinetics of certain steps in the overall reaction were studied. A rate equation for the oxidation of ferrous sulphate by gaseous oxygen was derived for the temperature range from 1000 to 200° C. An exact rate equation for the production of ferrous ion from pyrite could not be established but it was shown that the temperature, oxygen pressure, pyrite surface area, and the reduction of ferric ion by pyrite are important. A rate equation was derived for the reaction of manganese dioxide with ferrous sulphate. A major facfor controlling the rate was whether or not ferric oxide was formed by hydrolysis at the manganese dioxide surface.It was shown that if hydrolysis was prevented the factor cpntrolling the rate of the overall reaction ,was the rate of production of ferrous ion, and little ferrous ion was oxidised by oxygen. When hydrolysis of iron did occur, the overall rate was not a simplefunction of anyone factor and much ferrous ion was wasted by oxidation with oxygen.INTRODUCTIONIn another paper (Cornelius and Woodcock, 1958) the results of the reaction of an aqueous suspension of a manganese ore and pyrite with oxygen are reported. It is shown that the ferrous ion and sulphuric acid generated in situ by the oxidation of pyrite, dissolves manganese as manganous sulphate. To obtain a better understanding of the process as a whole, the kinetics of certain steps in the overall reaction were studied.When an aqueous suspension of a manganese ore and pyrite reacts with oxygen, the overall reaction may be conventionally represented by equation (1) (Cornelius and Woodcock, 1958).2Mn02 + 2FeSz + 6i02 + 2HzO= 2MnS04 + 2H2S04+ F'ez03 ... , .. (1)

Jan 1, 1958

This paper considers the application of recent laboratory gas sorption data to the understanding outburst phenomena in underground coal mining. Previous use of threshold limits based on gas content and coal rank are placed in perspective. Although this work focuses on overseas research and experience, parallels can be drawn for New Zealand coal settings, taking into account localised mining and geological factors.

Jan 1, 1994

By V Srinivasan, P Knights, C T. Farrelly

By 2025, with the widespread industry adoption of remote operation centres and advanced analytics, mining companies will find themselves making better, more informed decisions across the value chain. Process automation will drive significant business integration and reorganisation. Better collaboration between functions will make cross value chain optimisation a reality. Wherever possible decisions will be automated, based on analytical models and embedded in an enterprise decision management (EDM) architecture. This will take care of many of the minor day-to-day or the minute-to-minute decisions that consume operators and managers today. More flexible information technologies and architectures derived from the extensions to Web 2.0 and service oriented architecture (SOA) will solve many of the integration issues of today. The ongoing business imperatives for doing more with less people will make true collaboration with partners such as mining contractors, equipment vendors, transport providers, suppliers and maintenance contractors commonplace throughout the industry. All these organisations will be linked in and share common goals and objectives in real-time while providing visibility of internal constraints and available capability, allowing optimised decisions to be made across the extended enterprise. Humans will increasingly move to a more supervisory role and will use advanced collaboration to quickly solve complex abnormal issues that span the value chain out to the extended enterprise. The open collaboration and communication models instilled in the workforce through the widespread use of social networking technologies will drive thought leadership far beyond current æbest practiceÆ thinking. This will encourage the mining industry to extract the business value from rapidly converging fields of study such as environmental sciences, neuroscience, psychology, engineering, information technology and business finance. The future of mining will see a more uniform distribution of data savvy workers between the ages of 20 - 40, forcing a change in current operations. This group will drive the adoption of ubiquitous computing, augmented reality, presence and digital labelling. The enterprise will shift from a relatively static disparate set of functions to a digitally aware, integrated and interactive environment with information available, in context and just in time, to those who need it. The networked virtual enterprise will therefore be a reality.

Jan 1, 2008

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

THE flotation plant at Mount Lyell was erected, primarily, for the treatment of ore from the Lyell Comstock mine. These workings are situated over a mile in a direct line north of the North Mount Lyell mine, and are connected with the Reduction Work at Queenstown by a 2-ft. gauge steel tramway via the Queen River valley a distance of 7 miles. The property was purchased from the Mount Lyell Comstock Copper Co. After the disastrous fire in the North Mount Lyell mine in October, 1912, steps were immediately taken to make Lyell Comstock ore available for treatment, in order to relieve distress caused by any prolonged stoppage of work, and subsequently 13,032 tons of ore, averaging 3.38 %copper, 0.28 oz. silver, and 0.034 oz. gold; were smelted. When operations were resumed at the North Mount Lyell mine, it was evident that there was no economic advantage in smelting Lyell Comstock ore as compared with the higher value North Mount Lyell ore, which was also a better flux for the Mount Lyell pyrites, and that the future of the Lyell Comstock ore depended upon cheap mining and successful concentration of the ore. Therefore, extensive trenching and diamond-drilling was carried out, and a sufficiently large quantity of ore proved available for cheap extraction by open-cut methods. At the same time bulk tests by flotation were carried out at the Minerals Separation testing plant in Melbourne on different classes of ore from the Mount Lyell Comstock mine proper, followed by laboratory tests at Queenstown on all classes of ore available. All these tests demonstrated that the ore was amenable to the process, provided that it was ground finely enough. Plant erection was delayed by the general dislocation of business at the outbreak of war, but finally it became...

Jan 1, 1920

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952