Search Documents

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

Selection of mining methods, stope dimensions and stoping sequences is usually based on comparisons with other similar orebodies or rocktypes. Rock mechanics principles assist the process, which can be further improved by application of rock mechanics' models - in particular, computer based stress analysis techniques. These models vary in capabilities and potential application but, basically, can be subdivided into techniques which only model the surface of excavations, and those which model the total volume to be analysed. To address the wide range of geometries, stoping methods and sequences, and geomechanical environments at Mount Isa Mines, a number of models have been developed. By presenting examples of their actual and potential application it is demonstrated that appropriate use of these techniques will assist in the determination of mining parameters and improve ore recovery. Examples presented cover sequencing in tabular and massive orebodies, location of shafts and shaft pillars, and backfill and hanging-wall stability. It is concluded that surface techniques are more appropriate for regional analyses and volume techniques are more suited to analyses of detailed, local geometry. Colour computer graphics should be an integral part of data preparation, and results interpretation and Presentation.

Jan 1, 1986

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

By L Dawson, S Carr-Cornish, N Boughen, K Moffat, S Masterson

The risk and consequences of community rejection and loss of a social licence to operate is well articulated (Moffat et al 2018), however, the means for systematically managing this risk are less established. At the local scale, a mining operation is said to have a social licence to operate (SLO) when it achieves ongoing acceptance or approval from the local community and other stakeholders who can affect its profitability (Graafland, 2002). Without this social acceptance, it is very difficult for a business to operate effectively or profitably. It is well understood that social (or community) acceptance of a mine and its associated operations is a reflection of the quality of the relationship a company has with their host community (Thomson & Boutilier, 2011; Lacey & Lamont, 2014; Parsons et al., 2014; Moffat et al., 2015). Community relations are an integral part of successful mining operations and where these interactions are effective, they tend to foster mutual understanding, trust and support between a company and the host community (Kemp et al., 2006; Holley & Mitcham, 2016). Research further demonstrates that where such interactions are perceived to be procedurally fair, the increased trust created in these company-community interactions tends to lead to higher levels of acceptance of mining operations (Moffat & Zhang, 2014; Lacey et al., 2017).The challenge, however, is how to listen systematically to communities that mining and associated operations; communities that are often located across vast geographic areas and with diverse demographics. To date, traditional methods deployed to both guide and evaluate community engagement and social investment activities have been challenged to reflect the nature of the phenomenon they seek to observe, the voice of community. For example, detailed baseline surveys of community attitudes every three years by companies, as is the requirement within the policy frameworks of most large miners, provide rich insights but do not reflect the dynamic, temporal nature of the relationships that underpins their SLO. These processes typically are largely opaque to communities and distinct from the company’s engagement activities. The CSIRO Local Voices project was developed with Rio Tinto to go some way towards meeting this challenge of how to listen to the voice of community systematically. CITATION:Moffat, K, Dawson, L, Carr-Cornish, S, Boughen, N and Masterson, S, 2018. Listening to Local Voices – a systematic approach for understanding what a social licence to operate means for Rio Tinto in the Pilbara, in Proceedings Life-of-Mine 2018, pp 8–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Pratt V, Davis K

Challenges facing middle management in the 1980's and beyond are not confined to business matters such as industrial relations, government and legal constraints, corporate takeovers, and commodity marketing. More particularly they deal with people issues and the interrelationship of corporate/ family relationships. There is a need for corporations to acknowledge the growing conflict between corporate/family roles being brought about by such matters as equal opportunity, double professional marriage partnerships, personal mobility and the increasing stress faced by managers as a result of current demands and expectations being placed on them. While the main responsibility for managing professional life as well as the relationship between professional and private life rests with the individual executive, corporations nevertheless have a major responsibility to assist these executives in this management process. Corporations in Australia are taking steps to address this situation but much more needs to be done. This was highlighted in the March 1985 "Middle Management" course with its associated Spouses Programme presented jointly by Australian Mineral Foundation and The Australian Administrative Staff College. Effective communication is at the heart of the matter but no amount of training on this subject will bear fruit unless there is an associated commitment by executives to improve the effectiveness of their communi- cation process both in their corporate and family roles.

Jan 1, 1986

By Wall J, Platell R, Knight P

The Argyle diamond mine is located in the East Kimberley area of Western Australia, some 100 km south of the town of Kununurra. The diamondiferous Argyle olivine-lamproite diatreme was discovered in August 1979. Production began in December 1985 at a planned throughput of 3 Mtpa to recover 25 million carats of diamonds. Presently, Argyle is the world's largest producer of natural diamonds and produced over 40 million carats in 1993 from seven million tonnes of lamproite ore treated. Two phases of evaluation have been carried out. The first in 1981-82 was designed to prove around 60 million tonnes of ore to justify the establishment of a mine with a minimum life of 20 years. The second phase, in 1989-90 involved drilling the orebody to greater depths to provide data on which to plan the final pit design. The final pit contained 120 million tonnes of ore at 5.3 carats per tonne (ct/t) grade. Mining of the planned pit will extend the mine life to around the year 2004, following which it is possible that a further cut-back could be mined. There is also the potential for future underground mining. A substantial amount of geotechnical work has been undertaken due to the fact that the pit will be nearly 500 m deep and is located in a mobile zone causing abnormally high residual stresses to occur in the pit walls. The occurrence of low strength rocks at depth in the pit walls further complicated the situation. Hydrogeological investigations were done to determine pit dewatering requirements and to assess the effect of dewatering on pit wall stability.

Jan 1, 1994

By R Berry, J Hunt, T Kojovic

Geometallurgy aids the understanding of orebody variability through the integration of geological and processing information, thereby enabling spatial mapping of processing (eg comminution or separation) performance across a deposit. In order to do this, estimates of quantitative geometallurgical attributes are needed so that continuous downhole profiles can be generated for each attribute, providing vital data for the development of processing domains through geostatistical modelling. However, as traditional comminution tests are high cost and/or require large samples, current practice typically results in insufficient data density and distribution of comminution indices making it difficult to model and map deposit scale variability. The aim of this work was to find a method to estimate comminution indices based on data that is widely available at mine sites. This data includes mineralogy and chemistry of drill core samples, plus logging information such as lithology and alteration. Work to date indicates that comminution parameters such as semi-autogenous grinding (SAG) Power Index (SPI), Bond Work Index (BWI) and A*b (Julius Kruttschnitt Mineral Research Centre (JKMRC) drop weight test (DWT) Index) can be modelled using chemical and/or mineralogical data. The estimated hardness indices can then be propagated into the mine site database and used in the definition of processing domains that map inherent variability across a deposit. The estimates can thus provide geometallurgical inputs for spatial modelling, mine planning and optimisation initiatives.CITATION:Hunt, J, Kojovic, T and Berry, R, 2013. Estimating comminution indices from ore mineralogy, chemistry and drill core logging, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By C Young

In the vast expanse of Western Australia’s mining sector, a critical issue has come to light: many mining operations overlook the power of a Broad-Brush Risk Assessment (BBRA) to uncover their critical risks. This oversight has led to a cascade of challenges, where some mining endeavours find themselves grappling with: - Unidentified and unmanaged fatal risks, casting a shadow of uncertainty and heightened compliance risks. - A bewildering landscape where the concept of critical risks remains enigmatic, with some mistaking the risk register for the BBRA. - A fog of confusion surrounding the guardianship of these critical risks, leaving safety responsibilities blurred and undefined. Yet, the solution lies within our grasp. An effective BBRA empowers organisations to: - Pinpoint with unwavering certainty every ‘true’ critical risk. - Clarify ownership for each critical risk, ensuring accountability and swift action. - Create a prioritised roster of critical risks, illuminating the path to safer operations. - Lay the foundation for essential follow-up actions like bow-tie analysis, the identification of critical controls, and the fortification of the safety and health management system. Join us in this presentation, where we delve into the heart of an industry-leading BBRA process. Discover practical insights that will enable your organisation to craft and implement BBRA strategies, bridging the gaps in your journey toward preventing fatalities and fortifying safety protocols.

Apr 16, 2024

By A Audétat, W T. Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Middle and Lower Yangtze River metallogenic belt is one of the most important polymetallic resource areas in China. Iron oxide-apatite deposits, mainly distributed in Ningwu and Luzong volcanic basins, are a distinct type of iron deposits in this region. These deposits have a close temporal and spatial relationship with Mesozoic dioritic porphyries and are characterised by magnetite-apatite-pyroxene/actinolite ± anhydrite assemblage and large-scale sodic-calcic alteration.Widespread multiphase inclusions in pre- to main-mineralisation stage pyroxene and garnet in Meishan (in the Ningwu basin), Luohe and Nihe (both in the Luzong basin) iron deposits were trapped at ~780°C in extremely saline brines (~90 wt per cent NaCl equivalent), consisting of Na (13–24 wt per cent), K (7–11 wt per cent), Ca (~7 wt per cent), Fe (~2 wt per cent), Cl (19–47 wt per cent) and SO4 (3–39 wt per cent), based on petrologic, microthermometric, Raman spectroscopic studies and laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) analyses of natural fluid inclusions and synthetic analogues. The high Cl/Br, Na/B and S/B ratios in brine inclusions and the heavy sulfur isotopic values of anhydrite and pyrite (d34SAnh = +15.2 to +16.9‰, d34SPy = +4.6 to +12.1‰) suggest a significant contribution from both halite- and anhydrite-bearing sedimentary rocks. The involvement of evaporites caused the production of large amounts of high-salinity brines with apparently enhanced capacity to extract iron from the dioritic intrusions.According to their geologic features and the above characteristics, these iron oxide-apatite deposits are considered to be a special type of iron oxide copper gold (IOCG) deposits characterised by high contents of Na, Ca, Cl and SO4 in the ore-forming fluids. Moreover, we believe that evaporite-bearing sedimentary basins are more prospective than evaporite-free ones for these kinds of deposits.CITATION:Li, W T, Audétat, A and Zhang, J, 2015. The connection between evaporites and iron oxide-apatite deposits, Yangtze River, China – laser ablation inductively coupled plasma mass spectrometry analysis of Na, S, Cl and Br in fluid inclusions, in Proceedings PACRIM 2015 Congress, pp 623–630 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Y Shougu

Many mine accidents will affect the mine ventilation system when they occur. At present, there is a lack of monitoring means to capture the occurrence of accidents in time by monitoring the ventilation system, so as to take emergency measures to reduce the loss of personnel and property. Pressure wave is an elastic wave existing in air. Most accidents in mine will cause obvious changes of pressure wave. It is an innovative idea to monitor the occurrence of accidents in mine by measuring pressure wave. The development and functions of the pressure monitoring device and related software are introduced in detail. The pressure wave monitoring test is carried out in San Xavier underground mining laboratory, and the D-wave and S-wave waveform data are collected. The waveform characteristics are analysed, and the main frequency distribution of the pressure wave is found to be within 1 Hz by using FFT. At the same time, the influence of the propagation distance of the pressure wave on the waveform is analysed. The propagation velocity of D-wave and S-wave are roughly calculated, and they are 279.6 m/s and 397.3 m/s respectively. S-wave is slightly faster than D-wave. Although there are errors and uncertainties in the test, the test verified the feasibility of the existence and collection of pressure waves in the ventilation roadway, and provides a method for the future study of the propagation of pressure waves in the mine ventilation system.

Oct 12, 2022

By B Manda, K L. Sandvik, K Musiwa

Mining and processing of pyrite ore at Iron Duke Mine, north east of Zimbabwe, generates large quantities of acidic mine water as a result of the oxidation of iron sulfides on exposure to air and water used in the drilling and blasting operations. The acid mine drainage (AMD) contains elevated levels of dissolved Fe, Al, Mn and sulfate and has characteristic pH values ranging from about 0.50 to 3.00. Handling and disposal of such a drainage places significant impacts on the economics of the mining operation due to the corrosive nature of the drainage on infrastructure, the limitations placed on water reuse and discharge to the environment under a new law governing effluent discharge. Treated sludge at Iron Duke is chemically unstable, changing pH from ~7 to ~3 within four days after deposition in the evaporation ponds. The effluent does not meet the permitted level of neutral pH, 500 mg/l sulfate and less than 2000 mg/l total dissolved solids. Excessive acid seepage from the evaporation ponds has resulted in contamination of the ground water below the ponds area, which shows high mean annual levels of iron (368.67 mg/l), sulfate (1702.89 mg/l) and low pH (2.86) in addition to other pollutants. This poor quality seepage infiltrates into the nearby Yellow Jacket River, contaminating the public water source. Furthermore, a deterioration of the land area and vegetation adjacent to the tailings dump is also observed. Understanding the controls on the neutralisation of acidic drainage and long-term sludge stability after placement in evaporation ponds is essential to minimise costs of closure requirements and for the protection of environment and human health. This study examined the effects of the master variables pH, redox potential, acidity and alkalinity on acid neutralisation. The results indicate that ferrous hydroxides are not as stable as ferric hydroxides and that proper oxidation of iron also leads to better sludge stability, higher treatment efficiency and a manageable sludge viscosity. Metal hydrolysis and secondary mineral formation at the evaporation ponds under a wide range of pH and redox conditions is responsible for equilibrium shifts in metal reactions, resulting in high potential for metal leaching and mobility. Mechanisms of metal attenuation are also discussed.

Jan 1, 2006

By P Breuer, A Simons

The sulfidisation, acidification, recycle and thickening (SART) process is currently being used at NewcrestÆs Telfer Gold Mine to recover cyanide and copper from the cyanidation tails of the pyrite concentrate carbon-in-leach (CIL) process. While the process has been effective at attaining high recoveries of cyanide and copper, the Telfer SART plant has experienced higher than expected sulfide additions to achieve these recoveries. This paper details the results of surveys on the Telfer SART plant, which show that residence time appears to be causing the high sulfide consumptions. The paper also details the results of laboratory scale experiments which confirm the observed residence time impact during the acidified stage of SART.CITATION:Simons, A and Breuer, P, 2013. The impact of residence time on copper recovery in Telfer Gold MineÆs cyanide recycling process, in Proceedings World Gold 2013 , pp 189-196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By Schiller J. C, Both R. A

Base metal mineralisation occurs at several locations within the regionally metamorphosed Kanmantoo Group on the southeastern flank of the Mount Lofty Ranges between Kanmantoo and Strathalbyn, 50 km southeast of Adelaide. Sulphide mineralisation is of three main types (Seccombe et al, 1985):1. copper deposits, at the Kanmantoo and Bremer mines, South Hill prospect and several minor occurrences,2. lead-zinc deposits at Aclare, Wheal Ellen, Strathalbyn, St. Ives, Scott's Creek, and Glenalbyn mines,3. pyrite-pyrrhotite mineralisation of the Nairne pyrite deposit and many other pyritic schist units within the Kanmantoo Group.Syntheses of folding, metamorphism and stratigraphy of the Kanmantoo Group were given by Kleeman and Skinner (1958), Offler (1960, 1963), Offler and Fleming (1968), Marlow (1975), Mancktelow (1979) and Parker (1986). Studies of the general relationships of mineralisation to structure in the Kanmantoo area were given by Grasso and McManus (1954), Mirams (1962), Poole (1969), and Lindqvist (1969).Several conflicting views on the origin of mineralisation in the Kanmantoo Group have been proposed. Thomson (1975) considered much of the mineralisation as a late-stage product of regional metamorphism and he, like Parker (1986) and Lambert et al (1987), stressed the importance of major lineaments as an ore control. However, Lindqvist (1969) and Verwoerd and Cleghorn (1975) tentatively suggested a syn-sedimentary origin to the Kanmantoo copper deposit and Jensen and Whittle (1969) and Seccombe et al. (1985) on the basis of sulphur isotope data proposed a bacteriogenic sulphur source and a sedimentary origin for sulphides in the Nairne pyrite deposit. The latter suggested that most copper deposits represent stockwork, vein or disseminated zones within subsurface vents whereas massive mineralisation at Wheal Ellen and Aclare mines probably accumulated on the ocean floor.This paper presents new geological information on the structural and metamorphic setting of the base metal deposits and attemptsto relate this information to previous regional studies of the Kanmantoo Group. Estimates of pressure and temperatureof peak metamorphic conditions based on silicate mineral stabilities are considered in relation to various silicate and sulphidegeothermometers which have not previously been applied to rocks in the Kanmantoo Group.

Jan 1, 1988

FOR some time past keen interest has been shown in both America and South Africa in the mining drill-steel problem. This interest has extended to Australian mining fields, and Australian drill users, ever desirous of increasing efficiency, are vigorously attacking the problem. The writer has recently been engaged in the investigation of the problem on two of ,the biggest mining fields in Australia, and has formed very definite conclusions concerning the causes of many drill-steel casualties. He puts these views forward in the hope that they may be of interest to, both drill manufacturers and drill users. The subject is here dealt with mainly from the aspect of the properties of the steel and the modifications of these properties whensubjected to various manipulations. It is generally admitted that the drilling machine has greatly increased in power and efficiency during recent years, and the consequence is that the machine is demanding better service from the steel. This is being impressed on the drill users by an increase in steel casualties. This fact has led many mining people to the view that the machine has developed so rapidly that the steel maker has not been able to keep pace, and that consequently the steel isfailing by fatigue 0:1; so-called crystallization. This view is rather depressing. The writer, on the other hand, is inclined to discountenance fatigue as a serious factor under good normal working conditions where the steel is carefully manufactured and supplied to the user under suitable structural and sound conditions, and has subsequently received kind treatment at the hands of the drill sharpener and the drill user.It is not reasonable to attribute failures to fatigue until it has definitely been proved that the steel is fundamentally sound and is in the best structural condition to resist the stresses it is called upon to withstand, and, this being so, that all fundamental principles of...

Jan 1, 1923

By M A. Etheridge

The evolution of economic precious metal and copper-gold deposits in high-level igneous terranes is dependent on very efficient fluid focussing. This is most readily achieved by contemporaneous deformation, igneous intrusion and hydrothermal activity. Mineralisation in these environments generally occurs in fault and fault-vein arrays developed in the cover sedimentary and volcanics sequences above older regional scale fault systems. Such reactivated fault systems are particularly prone to developing tile complex fracture arrays, extreme local dilation and dramatic increases in permeability that are necessary to efficiently focus hydrothermal fluid and produce large mineral deposits. The arc systems of tilePacific rim are typically structurally and tectonically complex. At any given period in the evolution of an arc system, it may be dominated by extensional, compressional or strike-slip deformation. Indeed, it is common for the tectonic environment to change repeatedly through the development of a single arc segment. As a result, structures formed in one tectonic environment are commonly complexly reactivated in quite different environments later in arc evolution. These complexly reactivated structures have greater potential to localise extreme fracturing, dilation and fluid flux than primary structures. Application of this knowledge to practical exploration requires an understanding of the primary geometry of the controlling fault systems, the fault movements during reactivation, intrusion and mineralisation, and the consequent location and geometry of dilational sites. Simple 2D lineament analysis and targeting on lineament intersections does not suffice. Chemical processes that results from structurally focussed fluid flow may also contribute to permeability enhancement and further enhance fluid flux. Two main types of chemical feedback are important. The first involves selective dissolution of minerals during alteration and tile consequent production of increased porosity and permeability. The second occurs where alteration changes the mechanical properties of tile rock mass, especially where it leads to a greater propensity for fracture (eg by silification). In near-surface environments (< ~1 km), geomorphic processes complement fault systems in focussing fluid flow to develop sub-horizontal bodies of mineralisation, such as the giant Ladolam gold deposit (>42 million ounces of gold).   Along with classification schemes which stress crustal level, host rocks and alteration assemblages, the styles of high level 'epithermal' and reated deposits must also be considered in respect of their controlling co-active fault structures. Such structural understanding, combined with understanding of tile chemical processes involved (eg host rock reactivity), provides a major tool for exploration particularly in terrains obscured by deep weathering. Geological interpretation based on integration of field mapping with magnetic, radiometric and other remotely sensed imagery provides a powerful complementary tool to the traditional geochemical and geophysical targeting techniques. Timely and effective geological input is capable of reducing exploration risk and providing a more cost-effective basis for drilling and development. Examples of deposits associated with fault reactivation in extensional, compressional and strike-slip settings within arc systems are discussed in this context.

Jan 1, 1995

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

By A Fitzpatrick

An integrated and dynamic water balance and water quality model for a proposed base metal mine has been created using the GoldSimÖ software package. The model was initially developed to address the water quality of the Tailings Management Facility pond and how pond discharge would potentially affect downstream water quality. However, due to changing project objectives, the modelling has expanded over time through an iterative process to encompass the full mine site and all receiving environment water quality. The model results have been used as part of the mine planning/design process but are also intended to be used for the environmental impact assessment and permitting process. The model has been built to allow for changes to input terms to be readily made as additional data becomes available. The model results serve as a prediction of water quality and the potential project impacts to the receiving environment water quality. This paper presents the process by which data from a wide variety of sources was used to construct the model and how the model results were used to guide development of a conceptual water management plan. In addition, the role of the model in establishing proposed discharge criteria will be highlighted. The model has been delivered as a fully functional application with the intent that the end-user can be other than the modeller, the development of this aspect shall also be covered. CITATION:Fitzpatrick, A, 2012. Predictive site-wide water quality modelling as a tool for mine planning and permitting - A recent Canadian example, in Proceedings Life-of-Mine 2012 , pp 71-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By N J. Potter, N W. Brand, J M. F Clout

The increasing demand for iron ore with low concentrations of trace elements, puts increasing pressure on iron ore producers for high-quality material. Understanding the mineralogy, petrography, chemistry, and mineral association of iron ore deposits is becoming increasingly important to provide iron ore products that meet the ever-increasing standards of steel mills. Limited attention has been paid to documenting new orebodies beyond bulk RC drill chip assays and product specification data. Therefore, limited information is known about the spatial distribution of minor and trace elements at the hand specimen scale, and elemental deportment within different ore and gangue minerals. In this study, samples from high-grade microplaty hematite, supergene-enriched martite-goethite and hematite iron ores are examined for their elemental and mineral associations. These samples contain distinctive minor and trace element distributions, with the mapping of deleterious elements (eg Zn, As, Cu) enabling the deportment and abundance within the ore and gangue minerals to be assessed. Results from this study show a diverse range of minor and trace mineralogy that are present in typical iron ore samples, in abundances below the detection limit of routine XRD scans, that host the deleterious elements, including but not limited to, sphalerite (Zn and S), chalcopyrite (Cu and S), xenotime (P and Y), apatite (P and Ca), cryptomelane (K and Mn), barite (Ba and S), alkaline feldspar (K, Al and Si) zircon (Zr and Si) and chromite (Cr and Al). The presence of these minerals and associated deleterious elements, even at low concentrations, has implications for producers, with the ongoing restrictions and tightening of environmental constraints in shipped iron ore products. By understanding the distribution and location of these elements within the iron ore, steps can be considered to maintain increasingly higher quality iron ore supply around the world.

Nov 8, 2021

By R Goddard

An alternative stoping method has been adopted for narrow vein stoping at the Tasmania Mine in Northern Tasmania. Colloquially described as ‘Radial-in-Reef’ (RiR) stoping, the method employs the drilling of radial rings in the plane of the Reef from a drill stub located at the geographic centre of the proposed stope panel.Production from the Western Zone of the Tasmania Reef has been undertaken remotely from the Reef since 2007, after a detailed geotechnical engineering analysis indicated that the integrity of the sill drives could not guarantee an acceptable level of confidence should an anticipated seismic event occur within a radius of 10 m. The key tenet of the remote mining approach was the exclusion of personnel from sill drives once stoping had commenced. The remote mining method had to be ‘retrofitted’ to four existing stoping blocks totalling 11 sill drives which totalled 160 m vertically. The remote mining method proved to be complex, cumbersome and very expensive. However, the ore was extracted successfully.By early 2010, previously developed ore had largely been exhausted and the future development with an orebody open at depth presented the opportunity to review the current extraction method. However, the new extraction method needed to maintain the tenet of excluding personnel from sill drives of active stoping blocks, but seek opportunities to reduce the difficult and costly aspects of the previous method. The new ‘Radial-in-Reef’ stoping reduced the development requirement from six to two drives per ore block. Cost implications aside, the significant reduction in prestoping extraction ratio was expected to also reduce the likelihood of seismicity. Transverse production rings were designed to be drilled radially from a drill stub mined from a mid-stope footwall drive. Stopes totalling up to 7000 tonnes were planned be fired in a single electronic blast. Extraction was designed to take place from a basal sill drive under teleremote operation. At the time of writing, the method was under trial.

Mar 21, 2011