Search Documents

By F Shi, W Huang, D Seaman, K Runge

High Voltage Pulse (HVP) technology is a novel process that could potentially be the step-change needed in ore processability in the mining industry. The propensity of high voltage pulses towards mineral-enriched ore particles during treatment makes this technology selective and has the potential to enable ore pre-concentration by size separation. In this study, the potential for pre-concentration of a low grade copper-gold ore sample subjected to HVP pretreatment is investigated and compared to that achievable after mechanical breakage in JKMRC’s rotary breakage tester (JKRBT). The data show that a better pre-concentration result can be achieved after HVP processing than conventional breakage. The gold pre-concentration potential is much better than that observed for copper. 4D HVP pre-concentration characteristic curves were produced to assess the metallurgical performance possible as a function of energy input. The case study shows that when targeting a nominal metal recovery of 90 per cent for gold, the HVP pre-concentration technique can split the low grade ore (0.9 ppm gold and 0.28 per cent copper in the feed size 26.5-37.5 mm) into two components – a low grade oversize material (0.3 ppm gold and 0.15 per cent copper) and a high grade undersize material (1.0 ppm gold and 0.3 per cent copper). The mass split to the low grade is 23 per cent. Under this mass split scenario, gold recovery to screen undersize is 90 per cent and copper recovery is 85 per cent. The HVP treatment of this feed size requires a specific energy (spark) of 2.8 kWh/t.There is further research that would be required before industrial uptake of the HVP pre-concentration technology would be possible. This paper also outlines the research challenges that need to be overcome.CITATION:Huang, W, Shi, F, Antonio, C, Runge, K and Seaman, D, 2018. High-voltage pulse pre-concentration study using a low-grade copper-gold ore, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 327–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

Heatings, fires and explosions in New South Wales (NSW) and Queensland coal mines since 1972, are reviewed. Geological and mine settings are outlined. Where available, gas analysis and critical decisions are discussed. This paper updates work by NSW Department of Mineral Resources (1995) and the Queensland Department of Mines and Energy in a report on fires and explosion in Queensland coal mines (Richardson and Ham, 1996). Incident data has important applications in terms of evidence-based risk assessment and identifying key issues to be integrated into competency based training programs. Predictive indicators are reviewed in terms of coal parameters in seams where the incidents occurred.

Jan 1, 2005

By B Hannah, M Uriarte, F Labarca, C Madore, G Ganapathi, L Martin, T Haase

BechtelÆs Mining and Metals projects across the globe are executed in remote arid and semi-arid countries where providing even basic water supplies impose considerable challenges. Opportunities for water conservation measures using a Six Sigma initiative were proactively pursued to address the potential business impacts of limited availability of water resources. The initiative investigated areas driving water-optimisation during concrete operations and camp management. This paper details the water conservation evaluation of alternatives and cost/benefit analysis based on current and predicted water usage for development projects. Optimisation of water consumption through institutionalising more prescriptive standards for camp design and defining water conservation requirements have resulted in a new standard specification. Based on our projected mining project workload across the globe, it is estimated that for the period 2012 - 2015, a potential 5.5 M m3 water savings resulting in US$11 M could be realised for construction camps and savings of 4 M m3 of peripheral concrete process water resulting in potential cost savings of US$8 M could be achieved as a result of these revised standards.CITATION:Haase, T, Hannah, B, Ganapathi, G, Martin, L, Madore, C, Labarca, F and Uriarte, M, 2013. Water conservation at construction projects, in Proceedings Water in Mining 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Mauk, J Rowland

The Karangahake epithermal Au-Ag mine consists of two main lodes, the Maria and the Welcome/Crown hosted in Miocene andesites. Mineralisation is strongly constrained to major structures and is genetically linked to dynamic tectonic processes. Two main periods of faulting are represented in the deposit: 1. NE striking right-lateral/normal oblique linked spatially and temporally with the mineralising system, and 2. ESE striking right-lateral/normal oblique post-mineral faulting that displaces the lodes. Paleostress analyses performed on a limited kinematic data set indicate NW-SE extension during the formation of the vein system. Veins and lodes strike NNNE and accordingly contain a strike-slip component. The kinematics of vein formation at Karangahake is broadly consistent with that of other deposits within a NNE-trending belt of deposits. Oblique shear on deflecting structures will create zones of compression and dilation. Dilatant zones created on steep structures create fluid pathways potentially focussing large volumes of fluid from deep parts of the system into dynamic structures.

Jan 1, 2003

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G P. F Chitombo

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have been identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By J Robertson, D Williams, H D. Plewes

The co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material (Co-Mix) with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retaining capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimise acid generation and metal leaching. When compacted, Co-Mix materials have low volume change characteristics with respect to total stress and matric suction together with high shear strength. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures or a full depth waste repository. The theoretical properties of Co-Mix blends are investigated. The results of a laboratory program to characterise the physical and hydraulic properties of co-mixed tailings and waste rock are presented. Various ratios of tailings were blended with different waste rock materials. Hydraulic conductivity tests were conducted at confining pressures ranging between 0 and 400 kPa. The saturated hydraulic conductivity for the Co-Mix materials was found to vary between 4 + 10-5 m/s and 5 + 10-9 m/s depending on blend ratio, waste rock type and confining pressure. These results together with other physical properties show excellent hydraulic and strength characteristics can be achieved for Co-Mix materials.

Jan 1, 2003

By Chitombo GPF

The dilution of blasted ore with cemented backfill materials has been recognised as a significant factor influencing the economics of some underground metalliferous mining operations. Several mechanisms have heen identified as possible causes of fill failures. The purpose of this study was to determine the possibility of damage as the result of one mechanism, that of production blasting adjacent to bodies of cemented hydraulic fill (CHF). A vibration amplitude transfer function has been developed to model the transmission of blast vibrations from the source, through ore, across the ore to CHF interface and into the CHF mass. The model may be applied in the near field. The model has permitted estimation of vibration amplitude at a point in a CHF mass, to which damage criteria may be applied. A number of assumptions and simplifications have been made to render the problem relatively tractable. Ore and CHF material characteristics recorded by a number of authors were utilised to formulate preliminary damage estimations. A simple application of the amplitude transfer model indicated that a zone of plastically deformed CHF would be produced, and would extend to a distance of approximately 0.5 metres from the interface into the CHF. A sensitivity analysis was also conducted, that indicated that the zone of plastic deformation would be more extensive given appropriate conditions. Recommendations for further model development and future laboratory and field investigations have been made.

Jan 1, 1998

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

By A Morris

The Express Rail Link (XRL) will provide high-speed rail services from Hong Kong to Guangzhou and a connection to the national high-speed passenger rail network serving major cities throughout Mainland, China. The HK$ 67 B (NZ$ 11.5 Billion) project is of great strategic importance for Hong Kong and is being implemented to a very tight schedule, from early 2010 with completion targeted for 2015.The works include a 15 platform terminus station in West Kowloon, 26 km of twin track tunnels from the terminus to the Hong Kong/Shenzhen boundary at Mai Po, tunnel vent shafts/adits/emergency rescue siding and a stabling siding facility. Trains on the Hong Kong section are intended to operate at speed up to 200 km per hour and up to 350 km per hour on the Mainland section.This presentation will provide an overview of the entire XRL project, with a focus on the challenging geotechnical and spatial constraints on the tunnel works. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By G T. Jemwa, F Rousseau, F J. Wolfaardt, J A. M Rademan, P W. Smit

Mining companies are increasingly faced with the challenge of reducing operating costs while maximising throughput and profitability. At the same time, the grade and quality of treated ores are becoming poorer and more variable, resulting in suboptimal process performance.It is now widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In particular, progress in plant automation and control systems has seen a trend towards unified frameworks for control and optimisation of mineral processing plants. These frameworks seek to seamlessly integrate different roles and tasks involved in process operations - IT, automation, plant maintenance and operations. An integrated solution framework for reducing process variability, increasing process efficiencies and maximising plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis ægapÆ evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.Resolving these problems can potentially avoid unplanned downtimes, process instabilities and other operational surprises, thus ensuring optimal plant throughput and optimal process behaviour for improved recoveries. Integrating control systems and plant automation with advanced analytics to analyse and optimise processes enables operations to achieve reductions in the variability of key process parameters. In addition, early detection of equipment malfunction or suboptimal process conditions leads to improved equipment availability and reliability. Ultimately, these operational gains reflect in profitability because of plant throughput and recovery gains. These benefits are demonstrated using data from a South African gold mining operation, where such an integrated asset and process health monitoring framework for process optimisation has been implemented.CITATION:Jemwa, G T, Wolfaardt, F J, Smit, P W, Rademan, J A M and Rousseau, F, 2013. Towards an integrated framework for asset and process health monitoring and optimisation on a milling circuit, in Proceedings World Gold 2013, pp 137-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A H. Gray

Gekko Systems Pty Ltd engaged in the test work, design, manufacturing and commissioning of the pre-concentration plant at Silver Standard Resources Inc’s Pirquitas mine in the north western Jujuy province of Argentina. Testing of the ore at coarse feeds of between 2 and 12mm returned probable recoveries of up to a total of 95% silver into 50% of the mass fed to the InLine Pressure Jigs (IPJ’s). The plant has been designed and built based on the test results to include a preparation screen to bypass the fines that are naturally higher in grade and repulping of the coarse which is then pumped to three parallel trains of 2-stage IPJ roughing-scavenging. The target 50% yield to concentrate passes over a dewatering screen and the solids are returned back to the mill feed conveyor. The IPJ tails are transferred to a dewatering screen and solid rejects are stockpiled off the end of a transfer conveyor. All dewatered underflow products are processed via hydrocyclones to recover dirty water for use back into the IPJ circuit and return entrained fines to the fines bypass line.With the sulphide orebody being processed, the results from operations to date have shown that plant performance is matching the original laboratory sulphide ore testwork data. The objective of the pre-concentration step is to both reject gangue and achieve grades between 300-400g/t Ag to the float circuit as flotation recoveries are maximised within this range. The plant currently achieves overall upgrades of approximately 150% of feed grade with the IPJ only circuit producing an average 180% increase from calculated feed grade.

Aug 8, 2011

The history and milestones in the evolution of support systems utilised in the mass-mined chrysotile mines of Shabanie and King are discussed in detail. The use of block caving, false footwall or sublevel caving mining methods brings with it some major support problems, which are exacerbated, in our low rock strength mining environments. The paper discusses the various support elements and systems that have been used successfully or otherwise in these operations. Some predictions for the future of rock reinforcing in our ground conditions are highlighted, in relation to geomechanics, levels of mechanisation and production risk analysis.

Jan 1, 2000

By J E. Everett

Ore selection is generally a highly subjective task, with emphasis on producing product with a consistent target grade matching a perceived market requirement. A composite selection criterion ‘Comp’ (a linear function of the grade vector) can be used to maximise ore tonnage at a specified target grade (in Fe and contaminants) extractable from a block model. The blocks correspond to the selective mining units, with grades interpolated from diamond drill hole data. An iterative procedure has been developed to identify the coefficients and cut-off value for the composite function ‘Comp’, maximising potential ore tonnage at target grade.Commonly, target grade is predetermined by marketing; however, there is no guarantee that maximising ore tonnage at a specified target grade maximises the potential value of the mine. If the value of ore could be expressed as a linear function of the grade components, then these coefficients would be appropriate for the selection criterion ‘Comp’. The cut-off value for ‘Comp’ would correspond to the marginal cost of production; all blocks with a ‘Comp’ score above the cut-off would be classified as ore; and the cumulative grade of these ore blocks would be the average product grade over the life of the mine.Unfortunately, no such value function for iron ore is generally available. Methods for estimating the value function are discussed, using the spot price and sensitivities based either upon operational tolerances for Fe and the contaminants or upon published price differentials. This approach has been applied to an anonymous Pilbara deposit with about one million blocks averaging 1.1 kt. It is shown how the optimal target grade, cut-off grade and maximum tonnage can all be explored as a function of marginal cost and iron ore price. Alternatively, given marginal cost and an iron ore price, the effects of changing the tolerances (and therefore the relative costs of the contaminants) can also be explored.It is suggested this procedure can enable informed decision-making for an iron ore mine. Rather than setting final policy for the entire life-of-mine, the method enables target grades and tonnage estimates to be revised by re-computation as the mine life proceeds to recognise changes in market conditions and knowledge about the resource.It should be emphasised that this paper is concerned with ore selection rather than ore sequencing. Appropriate ore selection is a necessary but not sufficient condition for maximising value. Having identified the set of blocks that potentially maximise value, the sequence in which they are mined will present a trade-off between producing at constant grade and extracting high value ore early. The sequencing issue is not considered here. It is shown that optimum ore selection for an open pit mine is independent of any consideration of discount rates, although ore sequencing will depend upon the time value of money if the product grade is to vary across time.CITATION:Everett, J E, 2015. Ore selection to maximise value, in Proceedings Iron Ore 2015, pp 443–448 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By V A. Maltsev, V I. Panin

The question of prediction and prevention of dynamic events û rock bursts (RB), tectonic rock burst (TRB) and mining-induced earthquakes (MIE), induced by large-scale mining, are discussed. The mine itself and the host geological environment are taken as a natural-technical system (NTS) whose evolution is characterised by alteration of the adaptation-bifurcation (catastrophes) periods. So, to predict TRB-MIE means to predict the limiting NTS states that are determined from the NTS geological monitoring data, and to prevent the said events means to control the processes of rock deformation and failure within the critical zone. The study considers particular examples of how TRB-MIE-events are predicted and prevented in apatite mines, Kola peninsula, Russia.

Jan 1, 2000

Ok Tedi Mining Limited has recently completed the first phase of a trial to compare the performance of D26B Krebs cyclones in different configurations to the new Warman 650 mm CAVEX cyclones. From 1992, rougher flotation feed size has increased from the target d80 grind size of 150 ¦m with increasing SAG mill throughput. At high SAG mill throughput, operators have difficulty maintaining the target cyclone feed pressure and must increase the cyclone feed density, thus resulting in a coarsening of the cyclone split. Warman International have developed the CAVEX high capacity cyclone. The new CAVEX cyclones, when compared to the Krebs units appear to:produce a measurable increase in volumetric flow for the same pressure drop; maintain or decrease the proportion of coarse particles reporting to overflow; and lower the overflow density. In all plant trials to-date, the CAVEX cyclones appear to be superior to the standard Ok Tedi Krebs cyclones. Further testwork is planned to evaluate modified Krebs cyclones (with recent design improvements) against the CAVEX cyclones.

Jan 1, 2000

The Black Star lead and zinc ore-bodies, situated in the western zone of mineralisation at Mount Isa occupy an area 2000 ft. long with varying widths from 100 ft. to 300 ft. The strike is N5°W, and the average dip 60° West.To test at depth the potentialities of this area, an extensive diamond drilling campaign was commenced on 16th October 1927. It was continued, with from one to six machines working, until the end of 1931. During this period, 26 inclined holes, with an average depth of 1224 ft, and a total footage of 31,828 ft. were completed. A vertical hole, 2452 ft. deep, for comparative purposes, has been omitted.These drilling operations came directly under the charge of G J Gray, General Superintendent of Mount Isa Mines, and, in the early stages were supervised by E. D. McDermott, of the Mining Trust, London. The foremen, who were in charge of various sections of the drilling operations, were: H Vale, F Bray, J Winston and A A Sanstedt.

Jan 1, 1932

By M Runkel, J Hammerschmidt, A Holmstr÷m, A Charitos, J Gnntner

"Roasting of sulfide concentrates and refractory ores is an important process step in the production of metals and chemicals. Sulfides of iron, zinc, copper and other metals are oxidised with air between 600 and 1000¦C into metal oxides or sulfates and gaseous sulfur dioxide. Roasting of gold concentrates and ores is a typical processing step used to produce a porous calcine suitable for cyanide leaching. During roasting, elements posing problems are removed through: oxidation (carbon, sulfur, arsenic and antimony) or volatilisation (mercury, chlorides and tellurides, as well as arsenic and antimony).This paper focuses on the environmental aspect of roasting using fluidised bed technology. The approach is to show that roasting is an attractive solution for refractory ore pretreatment since, on the one hand, it is an efficient technique yielding high gold recovery rates, while on the other it is able to comply with current stringent international environmental regulations. In that respect, roasting is compared to alternative processes, ie pressure oxidation (POX), bio-oxidation (BIOX) and ultra-fine grinding (UFG). Roaster high gold recovery rates are ensured through roasting-leaching test work, which allows the derivation of respective roasting parameters that are easily achieved in an industrial plant. On the other hand, key elements of the roasting process are analysed, which make it an efficient and sustainable technology, ie the possibility for energy recovery, the removal of off-gas impurities during the different gas cleaning steps (handling of arsenic, mercury emissions and further hazardous dust and gas emissions) and the treatment of the SO2-gas in order to produce sulfuric acid, and finally the treatment of the effluent produced. The processÆs environmental aspects are summarised by listing roasting emission values that comply with international regulations.CITATION:Charitos, A, Runkel, M, Gnntner, J, Holmstr÷m, A and Hammerschmidt, J, 2013. Roasting - a study on environmental aspects, off-gas, effluents and residue treatment, in Proceedings World Gold 2013, pp 509-518 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013