Search Documents

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

Modelling and Simulation to Design a Flotation Circuit for Gold Concentration

Sep 13, 2010

Effect of Anionic Surfactant on Silica Particle Attachment at the Oil-Water Interface Controlling particle attachment is crucial where powdered solids come into contact with oil and water. Particles are trapped in a deep energy well at the oil-water interface, stabilising emulsions. Here it is shown that adding anionic surfactant causes dramatic changes to the bulk and interfacial structure of silica particle-stabilised oil-in-water emulsions. Exposing particle-stabilised drops to surfactant concentrations above the critical micelle concentration enhances the rate and extent of creaming and flocculation. Mixing particle-stabilised emulsions with surfactant solutions causes drop fragmentation. As the surfactant concentration increases, the average drop size decreases and particles are displaced from the interface during the mixing process.

Sep 13, 2010

Reverse Cationic Flotation of Iron Ores - Floatability of Amphiboles at Depression of Iron Oxides by Starch

Sep 13, 2010

Distribution of Settling Velocity of Irregular Particles and its Effect on Jig Separation Efficiency

Sep 13, 2010

By J E. Everett, F Grobler

This study considers realistic data for a planned open pit iron ore mine, but is applicable to any open pit situation. By interpolating drill hole data, grades are generated for a rectangular block model. Each blockÆs grade designation vector has components for each analyte (chemical element or compound) influencing ore value. Interpolation by means of geostatistical kriging leads to each block being assigned its expected value, and thus underestimates the overall grade variability. Alternatively, interpolation by means of conditional simulation is a method that implements random sampling from an infinite population of solutions. Each conditional simulation has appropriate overall grade variability, but estimating any blockÆs mean and variance requires sampling from multiple conditional simulations. For a block model, an ore/waste selection criterion maximises the expected tonnage at a target grade. This criterion is a linear composite of the grade components, with positive coefficients for the beneficial analyte (iron) and negative coefficients for the deleterious analytes (such as silica, alumina and phosphorus).Although conditional simulation gives the same expected grade as kriging for each block, the expected maximum tonnage of ore selectable at a target grade may differ from that obtainable from the kriged solution. We apply the linear composite selection criterion to each of 25 conditional simulations, as well as to the kriged block model. The resulting distribution of product tonnage is confirmed to have an expected tonnage that is over 20 per cent greater than that of the kriged model. The method also enables a selection probability to be computed for each block, and thus a probabilistic pit boundary distribution to be identified and used in mine planning. Proposed extensions will consider risk-based scheduling of the multiple selection solutions through minimisation of a derived æstress factorÆ and treating the mining process as an iterative system with actual or artificial ædepletionsÆ modelled in line with the mine plan, using the updated state (with new information) to re-evaluate the mine plan for subsequent periods.CITATION:Everett, J E and Grobler, F, 2013. Risk-based ore selection from conditionally simulated block models, in Proceedings Iron Ore 2013 , pp 149-156 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Following the Coalbrook Colliery disaster in 1960, Salamon and Munro (1967) established the well known empirical coal pillar strength formula in South Africa. This formula has prevented further violent multiple pillar failures. In 1996, a back analysis of the collapsed and uncollapsed cases in Australia led to the development of the Australian empirical coal pillar strength formulae. The original collapsed and uncollapsed coal pillar database of Salamon and Munro (1967) was updated in 2006. This study introduced various strength formulae for different coalfields and seams in South Africa through back analyses of collapsed and uncollapsed cases. Today, the resultant pillar strength formulae from these previous studies and the behaviour of coal pillars are mostly well understood and applied with confidence. However, it was assumed in the previous studies that the behaviour of pillars is not time dependent; therefore, the formulae established do not provide an associated time to failure of coal pillars. This paper attempts to evaluate the so called 'Geometrical Limits' concept to provide the Australian coal mining industry with a tool to assess the long-term behaviour of bord and pillar workings where the pillars are prone to failure due to spalling of ribs. In order to achieve this outcome, the principles of the safety factor concept and the probability of failure calculated using the coal pillar strength formulae have also been evaluated and practical design examples are presented in this paper.

Nov 25, 2010

Recycling of Process Water in Sulfides Processing and Flotation Selectivity

Sep 13, 2010

By N H. S Oliver

Five major veining events have been identified within the area surrounding the Mount Whaleback microplaty hematite deposit. These veining events can be directly correlated to the established deformation history of the Hamersley Province (Brown et al, in press). Vein formation temperatures of 203 to 231¦C have been obtained from primary fluid inclusions within veins which formed around the postulated time of ore formation. Preliminary proton induced x-ray emition (PIXE) analysis of these inclusions indicates KCl is the dominant salt species with varying levels of Ca, Fe, Ti, Mn present. It is suggested that some of these veins may have formed from feeder or effluent fluids from microplaty hematite ore formation.

Jan 1, 2002

By R N. Robson, A B. Christie, I J. Graham

Strategy development by the minerals industry identified the fragmented management of mineral resources as a significant impediment to the discovery and development of New Zealand Æs mineral resources. The total gross value of New Zealand Æs potential resources of coal and minerals is estimated at about $400 billion, but their potential value is not being realised. The management of minerals is now largely under the control of 86 local authorities (regional and district councils) and the lack of recognition of the significance of the sector has lead to inconsistencies in the way minerals are managed. The industry strategy influenced science funding for minerals, with the result that the 'mineral wealth' component now includes research on making better use of resource data in minerals management. Initially this research has targeted Otago and Northland regions where a number of initiatives are now in progress.   In Otago the Regional Council has budgeted to contribute $1 million towards a regional geophysical survey to advance mineral exploration and the management of subsurface resources in the region, to work cooperatively towards improving public awareness of the significance of minerals to regional economic activity, and to better coordinate policy-making for minerals at regional and district levels.   Crown Minerals, and the Far North and Whangarei district councils are considering providing funding support for an economic study of the mineral potential of Northland, building on a mineral resource assessment undertaken by GNS Science. Enterprise Northland is adding minerals to their list of potential growth sectors, and is supporting the operation of a Northland region minerals focus group.   Regional development agencies and local authorities have shown that they are willing to include mineral resources in their development strategies and to provide for them in policies and plans when supplied with information and assisted with technical support.

Jan 1, 2006

Certain Molybdenum Resources in Indonesia Mineralogical and Processing Study

Sep 13, 2010

By M Fahey

Large volumes of tailings are produced annually by the goldmining industry of Western Australia. This material ishydraulically discharged into large storage facilities usingsub-aerial deposition methods. Much of the gold comes fromhighly weathered rock, resulting in tailings with significant claycontents. Consolidation of these materials can be very slow,particularly if occurring under the effects of self-weight alone.To optimise the consolidation behaviour of the tailings, disposalstrategies can take advantage of the effects of evaporation byallowing each tailings layer to dry before the next layer isdeposited. In the last 20 years, much of the gold processing inWestern Australia has utilised saline groundwater. As the salinetailings dry, the surface will develop a thin salt crust. Laboratorytests have shown that these crusts can drastically reduce thesurface evaporation, adversely affecting the behaviour of thestorage. This problem has been the focus of an extensive researchprogramme, with the objective of obtaining a fullerunderstanding of the mechanisms controlling the coupledconsolidation and evaporation behaviour of saline gold tailings.Part of this study involved site investigations of a wide range ofstorages to ascertain their current states. Methods of gainingaccess to the tailings following deposition were developed.In situ testing and high quality sampling were conducted on each storage and samples returned to the laboratory for analysis. These investigations have enabled full characterisation of the storages to be accomplished. Examples of data are shown herein and the implications of the results are discussed.

Jan 1, 2001

By M Brady, O Salisbury, C Claassen, B Beamish, H Baxter

Monitoring for signs of elevated spontaneous combustion in the active goaf behind the longwall face is crucial for early intervention of any potential heating incidents. Typically, trigger action response plans (TARPs) are established at the start of longwall mining and often are only reviewed when triggers are activated frequently and become ‘nuisance alarms’, or in the worst case scenario after a heating event. Narrabri Mine has adopted a proactive approach of reviewing the longwall active goaf spontaneous combustion monitoring TARP at the commencement of each longwall block and prior to reaching a known ‘mylonite zone’ of crushed coal, which is associated with increased coal oxidation. The review is based on information recorded from the monitoring data of the previous longwall blocks as well as interpretation of relevant spontaneous combustion propensity results for the coal. This has resulted in the mine implementing a zoned TARP approach for each longwall block covering both the longwall retreat through normal undisturbed coal and the zone where the goaf is influenced by the increased coal oxidation associated with the mylonite coal. The consequence of this approach is that it has removed the issue of having nuisance triggers being activated during mining through a known increased oxidation zone, while maintaining a high awareness of indicators of spontaneous combustion.CITATION:Baxter, H, Claassen, C, Salisbury, O, Brady, M and Beamish, B, 2015. Implementation of a zoned trigger action response plan associated with changing mine conditions at Narrabri Mine, in Proceedings The Australian Mine Ventilation Conference, pp 113–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The transgressive sedimentary sequence of the Noumea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanics of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend froIn early mafic to younger evolved intermediate lithologies. The rhyolites are consistently calcalkaline. There is no evidence of mixing of the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to spreading in the New Caledonia Basin and involved reactivation of an earlier esozoic subduction zone.

Jan 1, 1995

Adsorption Isotherm Measurement of Sodium Oleate on Haematite Using Differential Thermal Analysis

Sep 13, 2010

Owing to improvements in computer capacity, it is now possible to undertake fully coupled or partially coupled, three-dimensional (3D) hydromechanical Finite Element (FE) simulation of mines, including explicit representations of large numbers of discontinuities. The analysis requires fewer assumptions than uncoupled analysis or two-dimensional (2D) analysis, but may require a change in how hydrological data is collected. The way hydrological data is incorporated in stability assessment and the approach to uncertainty in hydrological information also requires discussion. The current procedures for this type of analysis are discussed, along with some practical difficulties and teachings from early applications. A work flow for integration of 3D hydromechanical modelling with pit planning and some considerations for the management of uncertain data are also proposed.

May 1, 2010

By R Crookes

Mine to Mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian Mining Industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in NorthernQueensland, Australia, has espoused the Mine-to-Mill concept and isactively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROMstockpile. A blasting improvement program was undertaken betweenErnest Henry Mining, Thiess Contractors and Orica Explosives tooptimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance ofindividual blasts are needed before it is possible to optimisefragmentation or the downstream processes. These include suchspecialised Orica Explosives tools as SABREX, POWERSIEVE, andPOWERLINE and commercially available drill monitors. As importantare the more common still and video camera, borehole loggers,measuring tapes, surveying equipment such as face profilers, and ahigh-speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design - only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as theunderstanding grew and practices have been implemented resulting inreduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution.The continuous improvement program continues...

Jan 1, 2000

By A D. Campbell, G R. Power

The objective of the draw strategy in a caving mine is to maximise economic return by minimising waste dilution3 and maximising ore recovery4. The draw strategy must also include suitable controls for air blast and mud rush hazards and is highly constrained until continuous cave propagation has been achieved. This paper details a three-year project at the Ernest Henry Mine (EHM), which used cave flow simulation software to develop a draw strategy that increased the mine value by 32 per cent.Dilution and ore loss can be significant in sublevel cave (SLC) operations and result in poor recovery and considerable economic losses. To minimise dilution and ore loss, cellular automata software was used to simulate cave flow over the mine life. The optimisation project required mining footprints for various cut-off grades to be developed. Draw strategies for each mine footprint were then generated using a range of shut-off grades. Economic assessment of each scenario was then conducted to determine the mine footprint and corresponding draw strategy that generated the highest NPV (net present value). The iterative simulation process was improved by developing automated software functions in the flow modelling software to reduce time taken to generate and assess life-of-mine (LOM) draw strategy scenarios.In addition to improving the NPV of the mine, the optimisation project also enabled a decrease in the mine cut-off grade which increased the ore reserve and extended the mine life. Overall, an iterative process of mine planning, cave simulation, economic evaluation and geotechnical analysis was used to significantly increase the economic return of the SLC whilst ensuring caving risks were controlled to an acceptable level.CITATION:Campbell, A D and Power, G R, 2016. Increasing net present value by a third at an operating sublevel cave mine using draw strategy optimisation, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 167–174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A model was developed of a CIL/CIP circuit for recovery of gold and silver. The model uses a simple two rate representation of the leaching kinetics. Parameters for the leaching kinetics may be simply obtained by sampling the feed to a circuit and the tailings from each tank and assaying the solids for both gold and silver to obtain the assay profiles of the solids down the tanks. The parameters in such a leaching model would be expected to be a function of the ore type, the grind, whether oxygen was used and the general chemical environment. These parameters are primary inputs to the model for any simulation. Standard power law relationships are used to express the practical equilibrium between the gold and silver cyanides adsorbed on the active carbon and the tenor of the solutions. The parameters for this may be derived from solution and carbon assays for the same set of samples. The model is constructed by writing a mass balance for gold and silver in and out of each tank in the train and for the circuit overall. Other inputs to a simulation are the feed rate of ore, per cent solids of the slurry in the tanks, gold and silver loadings of the input æbarrenÆ carbon and the rate of movement of carbon through the circuit counter-current to the slurry. With appropriate practical parameters the simulation is able to reproduce typical tank profiles.

Jan 1, 2004

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010