Search Documents

By P Moser, P Schimek, F Ouchterlony

This paper summarises the findings of 27 model-scale bench blasts in magnetic mortar, which were conducted from 2011 to 2014 at the blasting site of the Montanuniversitaet Leoben.The aim of the study was the investigation of the influence of blasthole delay times in small-scale bench blasts on the face characteristics and cracking damage created in the surrounding rock, which affects the fragmentation in subsequent rows.The test specimens or blocks, which were produced out of magnetite concrete, were roughly 1:100 in scale to normal bench blasts. The confinement of the testing blocks at the sides and back ensured the similarity to normal bench blasts with regard to the wave transmission into the surrounding rock. The specimen contained three or four rows with five blastholes each and were shot row by row, with virgin (undamaged) material in row 1 and increasingly damaged or preconditioned material in the following rows.The tested delay times varied between 0, 28, 73 and 140 µs, which corresponds to 0, 0.4, 1.0 and 2.0 ms/m of burden.The evaluation of the material properties showed that the use of magnetite concrete eliminated the inhomogeneous behaviour of rock, but some unexpected differences of the individual production cycles were still detected.The characteristics of the bench after each blast was evaluated along three horizontal lines out of a 3D model of the bench face. The tested delay time sequences of the virgin (first row) and single preconditioned blasts (second row) produced more overbreak for longer delays, while the third-row shots resulted in a smoothened surface independent of the chosen delay.The introduced damage after every blast was evaluated by an observation of irregularities on the newly blasted bench face. The visible cracks at the top of the testing blocks were documented and divided into several crack families according to their angle, length and origin. The remaining block was broken out of the blasting site after blasting, cut into several horizontal and vertical slices and dye penetrant spray was used to visualise the cracks created. Some of the detected crack families showed an influence of the delay time. The calculated mean crack density and mean crack intersection density showed that longer delays resulted in a higher degree of damage.The fragmentation results were well reproduced by the basic three-parameter Swebrec function. The observed improvement of fragmentation in the second- and third-row blasts was linked to the preconditioning of the burden for the following row while blasting the actual row. With the exception of the simultaneously initiated blastholes, the blasts showed coarser fragmentation for the shortest delays, while the longest delays generated the finest fragmentation.CITATION:Schimek, P, Ouchterlony, F and Moser, P, 2015. Influence of blasthole delay times on fragmentation as well as characteristics of and blast damage behind a remaining bench face through model-scale blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Crawford G. R, Wold M. B

The application of the hydraulic fracturing technique to the measurement of in situ rock stress from underground excavation is discussed; including relevant theoretical considerations, equipmenl details, experimental technique and analysis procedures. Examples of the application of the technique at three Australian coal and metalliferous mining operations are given. The results obtained from these applications are compared with corresponding results obtained from overcoring tests conducted in close proximity at each site. Generally good correspondence in a wide variety of rock types is indicated. Experience gained with hydraulic fracturing at several underground mining sites has indicated it to be a quick, cost effective means of gaining an understanding of the in situ stress field in sufficient detail for many mine planning functions.

Jan 1, 1990

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

By A Li, H Jinto, M Laxman

The behaviour of tailings under cyclic loading has an impact on the stability and deformation of tailings dams and a good understanding of the cyclic behaviour of the tailings under earthquakes is important for tailings engineers and tailings operators for the design and safe operation of tailings dams. This paper presents an investigation into the cyclic behaviour of tailings using both laboratory cyclic direct simple shear (DSS) testing and numerical modelling. The laboratory testing involved cyclic DSS tests on gold tailings and zinc-copper tailings under different loadings and loading frequencies. The gold tailings specimen tested at a higher loading frequency and a higher cyclic stress ratio experienced spontaneous liquefaction during cyclic shearing and the zinc-copper tailings specimen tested at a lower loading frequency and a similar cyclic stress ratio exhibited ductile behaviour and liquefied due to cyclic mobility. The liquefaction behaviour of the tailings was modelled using an advanced constitutive model (UBCSAND), which was developed specifically to model soil liquefaction and strain softening under cyclic loading. The constitutive soil model presents the nonlinear soil behaviour under dynamic loading using a hyperbolic stress-strain relation. Dynamic analyses were carried out using a finite difference program FLAC. The cyclic stress-induced excess pore water pressures measured in the laboratory were modelled using numerical simulations of the laboratory tests under different loading conditions. The results of the non-linear dynamic analyses demonstrated the capability of numerical modelling of cyclic shearing induced excess pore water pressure and the onset of the spontaneous liquefaction. The laboratory investigation and numerical modelling technique provided the key properties and parameters for the dynamic analyses to assess the stability and deformation of tailings dams under design earthquake events. More importantly, the laboratory tests and numerical modelling provided some insights into liquefaction behaviour of the tailings during earthquakes. CITATION:Li, A, Laxman, M and Jinto, H, 2018. Liquefaction behaviour of tailings under cyclic simple shear testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 250–262 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C V. Deutsch

"Geometallurgical variables often cause problems to conventional geostatistical workflows. There are many variables; some are compositional and some are non-additive. They often show: complex multivariate relationships undersampling relative to conventional grade variables unequal sampling; that is, all variables are not available at all data locations.A variety of approaches have been developed over the years, but geostatisticians remain mostly focused on modelling rock types and a few grade variables with an abundance of data. The problems are reviewed and a chained workflow is presented where appropriate techniques are employed in sequence to permit reliable spatial prediction of geometallurgical variables. The spatial models may be used to assess the value of additional data, for prediction of process performance, for improved mine planning and other optimisation tasks. The chained workflow will include data transformations such as ratios and normal scores that make the variables amenable to geostatistical modelling. Data imputation techniques to account for missing values are considered with special consideration to spatial correlation with the available data. Decorrelation techniques such as the principal components, min/max autocorrelation factors and projection pursuit multivariate transformation are employed to manage massively multivariate modelling. Full distribution modelling must be considered to avoid biases in the prediction of non-additive variables. The post-processing of geometallurgical models must be streamlined for robustness and efficiency. The precise workflow varies according to the specific purpose of the study. Guidelines and thoughts on best practice are presented.CITATION:Deutsch, C V, 2013. Geostatistical modelling of geometallurgical variables - problems and solutions, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 7-16 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By Kasai H, Hibi T, Matsuishi S

Coal oil mixture (COM), a liquid fuel pro- duced by mixing together coal and heavy oil on the 50-50 basis, has been brought to a level of practical use in Japan, being actually employed by a oil fired system at Yokosuka Thermal Power Station of The Tokyo Electric Power Co., Inc. A COM Production Plant, built in Onahama which is located about 160 miles from Yokosuka, required COM to be transported by sea. Mitsubishi Heavy Industries, Ltd. therefore performed a series of studies to develop a spe- cialized COM carrier, the world's first of its kind. Long lasting high stability is of pri- mary importance to successful use of COM. Much have been done in the way of research on stability of COM in the static storage, and the mechanism of COM static: stability is almost completety known. On the other hand, the knowledge about the COM dynamic stability, such as the stability while being transported aboard the COM carrier at sea, is still limited at the moment. The motion of COM aboard the COM carrier and how COM would settle were studied by tests. A visualization test on the COM behavior under dynamic motion was also performed and the mechanism of COM dynamic stability was analysed. The tests showed that the ship rolling motion had @n effect of promoting the settling of coal content of COM in the cargo hold. And studies were also made to device a method for esti- mating the settling quantity of coal during sea Transportation.

Jan 1, 1987

By P Breuer, D J. Robinson, A McFarlane, L L. Kuhar

Increasing global demand for commodity metals and capital and the greater operating costs of mining and metal production present significant challenges for the metals mining industry. Current conventional technologies may not be feasible for processing deposits of declining grade, challenging mineralogy or those that occur at increasingly greater depths. To overcome these issues, the development of a step-change technology such as in situ recovery (ISR), which reduces mining and avoids milling costs, may be vital in ensuring future economic metal production. ISR has been used extensively to treat porous soft rock deposits such as the water-soluble salts, sylvite and halite. Although ISR has typically been used for mining conventionally uneconomic uranium ores, it has also been used less frequently for the treatment of other restricted permeability hard rock deposits, such as those containing copper and gold. The reason for the limited uptake of the technology for hard rock mineralisations is primarily due to low natural rock porosity and permeability and hence poor response to available lixiviant. However, additional challenges include solution containment, management of groundwater and regulatory, ecological and societal requirements and expectations. CSIRO has focused on understanding the challenges of hard rock ISR and identifying global capabilities that can contribute to developing the essential enabling technical areas required to realise ISR. Specific focus areas include geochemistry and advanced resource characterisation; drilling and controlled rock-breaking technologies; solution chemistry and environmentally benign lixiviant systems; lixiviant delivery systems and ‘subsurface mixing’; subsurface hydrology and reactive transport mechanisms and models; downstream processing options; legal, social and environmental aspects; and techno-economic modelling. This paper will discuss ISR challenges including industry feedback focused on addressing this issue, gaps preventing ISR from being applied in practice, capabilities to overcome these gaps and the development of a collaborative approach to making hard rock ISR a reality.CITATION:Kuhar, L L, Breuer, P, Robinson, D J and McFarlane, A, 2015. Making hard rock in situ recovery a reality, in Proceedings Third International Future Mining Conference, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By X S. Li

The modern mechanical excavation machines have enough power for cutting hard rock. The ‘bottle neck’ which limits the use of machines for hard rock excavation is ‘cutting tool’. To cut hard and abrasive rock, CSIRO has been developing Super Material Abrasive Resistant Tools (SMART*CUT). SMART*CUT technology replaces the tungsten carbide (WC) tip of conventional pick with thermally stable diamond composite (TSDC) and attaches the TSDC tip to steel tool body with CSIRO worldwide patented bonding technology. This paper introduces the key features of SMART*CUT, compares its performance with conventional WC tipped tools, discusses the challenges faced by SMART*CUT and the further developments needed for successful application of SMART*CUT to mining industries.

Nov 22, 2011

By M Watkinson

Tube bundle monitoring systems have come a long way from their first introduction to coal mining in the late 1960s/1970s. Early developments in the United Kingdom (UK) commenced with single gas analysers (carbon monoxide) and quickly moved towards introducing oxygen analysers and methane analysers for improved analysis, in particular the calculation of air-free results. Recommendations were made in the early days as to how and where to run tubes and on the matching of sample pump and purge pump pressures. Current Australian installations are commonly based on a four-gas multianalyser, infrared for carbon monoxide, carbon dioxide and methane, and paramagnetic for oxygen. These systems are controlled with programmable logic controllers (PLC), with component monitoring as an integral part of the software. This paper discusses the development of tube bundle systems from the 1960s to the current date and looks at the advantages and disadvantages of the installations, along with making operational recommendations to be considered with the siting of the analyser building, running of tubes and maintenance of the system.CITATION:Watkinson, M, 2015. Developments in tube bundle gas monitoring, in Proceedings The Australian Mine Ventilation Conference, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The performance of the Australian Mining Industry over the past 10 years using key indicators of production, revenue, aftertax return investment, together with key cost elements, market changes and ore reserves is briefly reviewed. The elements of competitiveness are discussed forthe industry and the effects of Government charges and policies relating to existing operations are outlined. There is a demonstrated need for improvements in competitiveness in direct and indirect costs and for improved access to resources for the mining industry to continue to grow and add to Australia's economic growth.

Jan 1, 1987

By L Stitz, S Kinnear, L D. Fabbro

Sensitive and tolerant species of macroinvertebrates were present across a wide range of conductivity concentrations in the Isaac River catchment in Central Queensland, indicating the need for further ecological studies in the field to underpin the development of regionally-tailored guidelines for conductivity. The Isaac catchment has naturally high conductivity, but there is also increasing pressure on resource companies to ameliorate saline mine water discharge. Recently, catchment management efforts have included a revision of the water quality guidelines that are specific for the broader Fitzroy catchment. These guidelines include the use of macroinvertebrates as indicators of ecosystem health, but developing and applying such guidelines first requires a good understanding of macroinvertebrate ecology and population dynamics, ideally from field validation. To date, studies of macroinvertebrate tolerance to conductivity in southern freshwaters, as well as in laboratory-based ecotoxicological tests conducted in Queensland, have suggested that ranges exceeding 1000 ¦S/cm are likely to have negative impacts on survivorship of all taxa. However, these results may not be transferable to natural populations of macroinvertebrates from the Isaac, where the naturally high-conductivity water may allow the opportunity for adaptation. To test this, macroinvertebrate assemblages were examined at a series of sites in the upper Isaac River catchment at the end of the dry season in 2012. Patterns in the assemblages were examined together with water quality parameters, in order to gauge the ability of macroinvertebrates to survive at conductivity concentrations exceeding 1000 ¦S/cm. The specific conductance of the field sites ranged from 477 ¦S/cm to 9791 ¦S/cm and a total of 39 families from 13 orders were identified. Species richness was not significantly different between sites of differing conductivity. Macroinvertebrate populations were dominated by Dipterans as well as the traditionally more pollution-sensitive families Ephemeroptera and Trichoptera. There was an absence of any correlation between conductivity and species richness (P > 0.050), suggesting that macroinvertebrate taxa richness occurs independently of conductivity, at least in this particular cohort of mining and/or grazing influenced ephemeral systems in Central Queensland.CITATION:Stitz, L, Fabbro, L D and Kinnear, S, 2013. Macroinvertebrate tolerance across a range of conductivities in the Isaac River Catchment (Central Queensland), in Proceedings Water in Mining 2013 , pp 135-142 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P Kirsch, P Jagals, D Viswanathan, J Shandro, R LaBouchardiere

The planning, design and operation of mines must include the development of positive environmental, community and land-use benefits if it is to achieve good corporate social responsibility and minimise detrimental impacts throughout the life of the mine. Life-of-mine (LOM) planning should, therefore, consider conducting mining activities in the best socially, environmentally and economically acceptable manner, from the commencement of exploration to post-closure of the mine. Current knowledge of LOM activities in relation to public health (life-of-community, or LOC) impacts neither fully captures the full suite of human health and well-being impacts, nor comprehensively informs society on these issues. This knowledge gap is becoming more apparent as public antipathy is increasing towards mining activities within Australia, Canada and globally. The purpose of this paper is to present preliminary and informative results of a literature review to gain insight into the extent of available public health and well-being knowledge associated with mining development. LOM development must also benefit the LOC, in that it must aim to minimise detrimental impacts, and maximise beneficial (including health) impacts on all associated communities. Health planning and programing for mitigation of potential adverse health impacts of mining should extend beyond the scope of work-related injury and illness (resulting from chronic exposure to harmful substances, infectious and lifestyle illnesses), to the health and well-being of workersÆ families and extended associated communities. By mapping the available but rather scarce literature on LOC areas to recognised LOM stages, this review found shortcomings and imbalances regarding research reporting on mining and its health-related impacts in the worker-to-community continuum.CITATION:Kirsch, P, Viswanathan, D, LaBouchardiere, R, Shandro, J and Jagals, P, 2012. Health impacts extend from the life of a mine to the life of a community - Knowledge gaps, in Proceedings Life-of-Mine 2012 , pp 161-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

The activiltion of sphalerite with electrolytically generated copper ions from a copper electrode instead of the usual practice of the addition of copper sulphate was studied in the laboratory. A large surface area of copper was provided by lining three sides of a bench flotation cell with copper sheeting. The lining was connected to the positive terminal of a low voltage d.c. source, and the cell impeller to the negative terminal.Sphalerite was effectively activated by this arrangement and was subsequently floated using xanthate as the collector.Flotation results comparable to those obtained with 1 lb/ton CuS04.5H20 (0,255 lb/ton copper) were obtained using 0·1062 lb/ton of electrolytic copper and 0·488 kWh of electrical energy. The wastage of copper due to the formation of insoluble precipitates was found to be dependent on the length of time the current was passed. Maximum current was passed for the shortest time to minimize wastage.

Jan 1, 1973

By X Li, W McKeague, M S. Powell

This paper explores the importance of operators in the overall efficiency of mineral processing plants. With the potential of future control configurations becoming more remote, it is time to review the implementation of control and utilisation of operators. This paper is based on a preliminary review of operators and control room operations and clearly shows that, in the minerals industry, operations are typically run in a reactive mode (with a focus on ensuring equipment operation), rather than in a proactive mode (with a focus on optimising the process performance). The primary reason for this misguided approach is the short sighted thinking applied to the challenges of designing technology and organisational tools capable of addressing the essential operational needs: an approach which inevitably results in a disconnect between people and technology. Contrary to the popular approach of replacing operators with expert systems, the thesis of this paper is that the shift to more complex circuits, with higher demands on processing capability and control, will require the actual upskilling of operators. Experience in mineral processing and other industries indicates that expert systems cope well with small changes but are typically unable to respond to major changes in feed material and this is where the expert operator becomes crucial. Providing operators with ongoing high level training in process understanding, and restructuring how they interact with the plant and interface with the control system is the approach being proposed here - an approach surprisingly underutilised and often absent in the minerals industry today.CITATION:Li, X, Powell, M S and McKeague, W, 2012. Unlocking processing potential by empowering our operators, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 333-340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By Y Lanwin

The Australian mining industry, a cornerstone of the nation’s economy, is on a journey towards greater equity and inclusion. Th paper introduces a comprehensive exploration of how universal design principles, stemming from architectural roots, have evolved through automation and digital technology into the more encompassing frameworks of inclusive design and equitable design. The paper proposes a practical framework for those involved in work, facilities and equipment design in the mining industry to identify and assess for equity and inclusion. Universal Design emerged in the 1960s with a primary focus on architecture, aiming to create spaces accessible to people of all abilities. Its foundational principles sought to ensure equitable use, flexibility, simplicity, perceptibility, tolerance for error, low physical effort and optimal spatial considerations. Over time, these principles evolved and expanded beyond physical spaces, finding applications in various fields, including technology, education and transportation. In response to advancements in technology and a growing understanding of the multifaceted nature of diversity, Universal Design evolved into Inclusive Design. Inclusive Design goes further than mere accessibility, considering a broader spectrum of users with varying cognitive, sensory, cultural and socio-economic backgrounds. It emphasises user centred design, customisation options, diverse user research and continuous iteration. Equitable Design emerged as a framework that addresses not only the diversity of needs but also systemic disparities. It emphasises fairness, justice and the elimination of structural inequities. Equitable Design encompasses accessibility and affordability, representation and diversity, ethical considerations and community engagement. This paper will explore the applications of these design principles through a series of case studies including village and on-site facilities, remote operations and office based work design and technology design. By applying these frameworks in a mining context, the paper proposes that mining companies and suppliers can improve diversity, equity and inclusion leading to safer, more engaged and productive workplaces.

Apr 16, 2024

By ALAN J. HARGRAVES

It is normal that Shepherd and Rixon, in their contributed discussion (this issue) see differences with Hargraves (1983), as it exemplifies the present uncertain situation worldwide, a situation expected to remain until better understanding and wider agreement lead to the real goal of the prevention of instantaneous outbursts of coal and gas.

Jan 1, 1983

By M Szwec, P Corbett, P Sheffield

Centennial Coal operates the Springvale and Angus Place longwall mining operations that extract coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale and Angus Place mines have a history of difficult geotechnical conditions, where mining operations are conducted with a thick coal roof interbedded with numerous claystone units and relatively high levels of vertical and horizontal stress. The combination of a relatively high stress regime and weak laminated roof has led to numerous roof failures throughout the mine’s life.Following underground roadway development, the mine roadways can experience high levels of roof movement that can lead to roof falls. Two-point wire extensometers (known as ‘telltales’) are extensively used for roadway condition monitoring. Along with extensive other geological and geotechnical data, monitoring data is used to prepare geotechnical hazard plans that are then used in all areas of mine planning to allow for safe and efficient operation of the mine.This paper presents a case study of the use of a new software tool that allows time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. It can be used in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological/geotechnical data to allow correlation of monitoring data with risk factors.CITATION:Corbett, P, Sheffield, P and Szwec, M, 2014. A new tool for extensometer data analysis and improved understanding of geotechnical risk factors, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Q Yu, G Ren, Z-Y Chen, J Yang

The wedge shape theory of the rock fragmentation range in bench blasting is presented according to the dynamic characteristics of rock fragmentation by blasting in open pit under the condition of hole-by-hole initiation. The finite element software ABAQUS was used to analyse the rock fragmentation mechanism. The rock mass stress contours, crack propagation and damage evolution of different moments were obtained. The results showed that the wedge shape theory of blasting is closer to the rock fragmentation in hole-by-hole blasting and is useful to the design and calculation of charge weight.CITATION:Yang, J, Chen, Z-Y, Yu, Q and Ren, G, 2015. The wedge theory of borehole charge design for bench blasting and its numerical simulation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 169–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014