Search Documents

By Zden[e]k P. Bažant

Due to their heterogeneity, most rocks fracture with a zone of distributed cracking ahead of the fracture front. This makes linear elastic fracture mechanics inapplicable. The present study describes a mathematical model in which the progressive microcracking is taken into account by strain-softening stress-strain relation. In a simpler version of the model, the triaxial strain-softening stress- strain relation is obtained by direct adjustment of the elements of the compliance matrix. This formulation is rigorous only if the principal stress directions do not rotate during fracture formation within the fracture process zone. As a more sophisticated and generally applicable model, the so-called microplane model which is an analogue of the slip theory of plasticity is outlined. Comparison with fracture data for various rocks are given.

Jan 1, 1984

By Johannes Moeljono, Werner Wenzel, Heinrich Wilhelm Gudenhau

As an important mechanism for increasing production of the suction-draft-sinter process, it has been shown that gas permeability through the sinter layer plays an important role. Methods to increase production rates have been indicated and suggestions for carrying out the process have been made to improve the rate of production, reduce the fuel consumption, and at the same time obtain a uniform sinter. Laboratory experiments were conducted at the Institute for Ferrous Metallurgy of the Technical University at Aachen to illustrate these methods. Methods of Increasing Gas Penetration Through Sinter Layers The following are of fundamental importance in determining the process cycle during the sintering of iron ores: 1) Generation of maximum temperature, since its form and range determine sinter quality. 2) Propagation velocity of the temperature maximum which controls the attainable output. 3) The convective heat transfer which influences the velocity of travel of the temperature maximum.

Jan 1, 1974

President Howe: It is, of course, not easy to discuss off-hand the paper which Mr. Becker has presented with so much lucidity. I will only make one remark, which is outside of the line of his argument, and concerns merely a passing allusion in his paper. Mr. Becker speaks of the fact that glass breaks with a flat or conchoidal fracture, and that steel shows a rough or " cupped " surface of frac-

Jan 1, 1895

By Lawrence F. Rooney

One of Edgar Allan Poe's stories that haunts my subconscious is the Masque of the Red Death. These days, whenever I join a group like this, especially during the cocktail parties, I see myself and others as those mythical swingers seemingly isolated from the plague. The world, but this country especially, has had a ball plundering, spending, and wasting its natural resources for 100 years. And, as in days of yore, it is fitting that we end this ball with spectacular fireworks: trips to the moon, so that our grandchildren, huddled in their caves along the Ohio, will better understand how it all began.

Jan 1, 1970

By Richard A. Hawkins

O the American coal man, Australian coal mining most appear to have little, if any, influence on American coal-mining practice and to bear little relation to it. Actually, the relationship has been close, for Australian operators have carefully studied American practice by reading American technical publications, by consulting American engineers, and by visits to Ameriean operations. They have leaned heavily on America for their supply of mechanization equipment and many American mining-machinery manufacturers are active in that country, supplying its needs and furnishing technical assistance. Australia's influence on American coal mining has been obscure and probably negligible. However, it seems reasonable to assume that this influence will increase. The wartime development of air transportation will inevitably bring these two countries into much more intimate contact than existed in recent years. American servicemen. many of them former miners and coal-mining technicians, have visited Australian operation, while stationed in that country, have talked with operators and men over there, and undoubt-

Jan 1, 1945

By William I. Busenbark, Elmer C. Newman

At Bingham Canyon, the world's largest open-pit copper mine, annual grease consumption is in the neighborhood of 109 000 kg (240,000 lb), all of which was 544 (120-16) purchased, warehoused, and distributed in 54-kg (120-1b) and 180-kg (400-1b) drums. While perhaps a menial and mundane chore, grease distribution shows on the ledger as a significant expense item. To improve labor and cost performance, Kennecott maintenance engineers undertook a study to find the most direct method for moving multi purpose grease (MPG) from the refinery to the point of final consumption. What they found was a direct vendor system for hulk grease so simple and flexible that long-established drum distribution is being phased out in favor of the newer method throughout 75% of the operation.

Jan 9, 1977

By D. J. McAdam, G. W. Geil, D. H. Woodard, W. D. Jenkins

.In a series of papers, the authors and their associates have shown that the resistance of a metal to fracture is a function of all three principal stresses. Consequently since a technical cohesion limit is defined as the technically deter-minable resistance to fracture under a specific stress system, the technical cohesive strength comprises an infinite number of technical cohesion limits corresponding to the infinite number of possible combinations of the principal stresses. As shown in the previous papers, the technical cohesive strength increases with plastic deformation, with decrease in temperature, and with increase in the strain rate. The technical cohesion limit, therefore, is affected by the same factors that affect the flow stress,$ namely, the stress system, plastic deformation, temperature, and the strain rate. The effect of each of these factors on the fracture stress is qualitatively the same as its effect on the flow stress. The effect of any of the factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. Since the term "fracture stress" has come into general use with the same significance as technical cohesion limit, the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. In the general investigation described in the previously-mentioned papers, 10-18,20,21,23 the influence of the stress system on the fracture stress was studied by means of tension tests of notched specimens. When a circumferentially notched cylindrical specimen is subjected to longitudinal tension, the minimum cross section is under transverse radial tension. The mean radial stress increases with the depth and sharpness of the notch, but is always less than the longitudinal stress. The greatest principal stress (S1), therefore, is longitudinal, and since the radial stress is effectively equal to the circumferential stress, the transverse principal stresses are equiaxial in that plane (Sz = S3). By the use of notched specimens in tension tests it was shown that the fracture stress increases with increase in the radial stress ratio (s3/s1) The evidence is based not only on the results of tests to fracture at various constant temperatures, but also On results of two-stage tests, in which each specimen was plastically deformed a predetermined

Jan 1, 1949

By H. V. Flagg

OPERATION of a modern steel plant presents a curious anomaly. Large-scale operations, in which large volumes or heavy weights of materials are involved, are not usually subject to close control or narrow specifications. On the other hand, operations that call for a high degree of precision are usually carried out under carefully controlled conditions with delicate, precise machinery and tools, and production is made secondary to quality. In a modern steel mill both extremes are taken as a matter of course. A strip mill making auto-body sheets must supply its customers with sheets that all come within a tolerance of plus or minus 0.003 in. in gauge at any point from side to side or end to end, and without blemishes either of color or surface. Sheets that were considered par excellence as recently as ten years ago could not even find a market today. Such exacting requirements have made necessary a nicety of control that approaches the watchmaker's art. Notwithstanding this necessity for precision, the scale of operation is stupendous.

Jan 1, 1940

By Pierre de P. Ricketts

Having had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

By Pierre de P. E. M. Ricketts

HAVING had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

Jan 1, 1876

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By G. M. Crosby

Seven mines with important production records in the Coeur d'Alene lie adjacent to the Gem stocks —the Frisco (Gem), Hercules, Interstate, Rex (Sixteen to One), Success (Granite), Sunset, and Tamarack. Old records are incomplete, but available data given in Table I show these mines have produced 10.550,721 tons of ore containing more than 50 million oz of silver, more than 1.5 billion lb of lead, and about 1 billion lb of zinc (approximately 1.25 million tons of lead and zinc combined). Average ore grade is 4.8 oz of silver per ton, 7.2 pct Pb, and 4.6 pct Zn. This impressive production represents about 12 pct of the District's yield. At present metal prices, with modern beneficiation, the gross value would be more than $400 million. THE GEM STOCKS The Gem stocks, considered to be outliers of the Idaho batholith of Late Cretaceous age, are located in the northern half of the Mullan quadrangle, and extend from the town of Gem, Idaho, along a strike of N30°E for a distance of approximately five miles. They occur as two major masses of monzonitic rocks commonly referred to as the North stock, which covers an area of 1.1 sq miles, and the South stock, which covers 2.6 sq miles. The areal pattern is roughly club-shaped, the North stock representing the handle and the South stock the head of the club. Two and a half miles west and five miles northeast are two groups of smaller stocks, isolated from the main masses but of the same general rock type. This discussion is limited for the most part to the North and South stocks. At the north end, where the intrusion is about 3200 ft wide, the walls are about parallel and dip very steeply west. At the south end, where the mass is about 7000 ft wide at surface, the walls dip away from each other at moderately steep angles. An aeromagnetic survey' detects and outlines with surprising accuracy the two main stocks. as illustrated on the magnetic contour map (Fig. 2). Of particular interest is the location and shape of the magnetic anomaly representing the South stock. The anomaly is centered over the south end of the outcrop, and a westerly extension joins it with a smaller anomaly over the Dago Peak stocks. The latter anomaly, likewise, is located over the south end of the isolated stocks. This pattern suggests the intrusion has greater extent at depth to the south and west. Though correlation between the Dago Peak stocks and the larger masses is suggested, the controversial aspects of the Dobson Pass fault, which separates the two areas, casts doubt on a correlation. Topographically the monzonite stocks are ignored by the drainage pattern indicating these rocks, and the invaded rocks of the Lower Belt Series react similarly to erosion. The drainage patterns of Nine Mile and Canyon creeks cut indiscriminately across the monzonite-Belt contact, resulting in both valleys and ridges in the southern end of the intrusion. Nine Mile Creek traverses diagonally the entire five-mile length of the stocks. The monzonite rocks of the intrusion are referred to locally as granite, but granite is rare and the rocks comprise a wide variety of types. Their characteristics, described in detail by F. L. Ransome and F. C. Calkins,' are summarized by P. J. Shenon.' The principal rock type is coarse-grained, light gray, porphoritic monzonite containing black crystals of hornblende. Pyroxene, epidote, and titanite

Jan 1, 1960

By P. L. Allsman

A method of analyzing blasting action indicates that major cost savings are possible by revising practice and bringing the classical blasting formulas up to date; difficult problems such as taconite and throw-breakup can be attacked by engineering Denonation pressure — the peak pressure developed by the explosive reaction; "shatter blasting." Average detonation pressure — the average pressure over the time the reaction continues; "heave blasting." Radial presswe — the stress in a radially expanding sphere about the detonation. Corresponds to the diminishing peak pressure. Lateral stress - the stress in a circumferential direction, induced by outward movement of the rock away from the detonation. Limiting stress or Slim— the rock property at which failure will occur in the case at hand; may be tensile or compressive strength, or combinations. Recent developments in explosives technology, following the advent of nuclear explosions, have led to a rather complete understanding of their action. A survey was made for the purpose of uncovering any knowledge which might be applicable in the mining and quarrying industries, the principal users of explosives. Although no revolutionary techniques have become apparent, much basic data pertaining to blasting — fortunately not classified — have been developed by recent research, from which a good general understanding of the process can be derived. It is hoped this explanation of the scientific principles governing explosive action, together with a proposed analysis of blasting practice, will further the development of mining engineering. NATURE OF THE REACTION: The phenomenon of explosion, termed detonation, is in reality a rather complex chemical reaction, and as such is completely explainable by physical and chemical laws. Detonation is characterized by high temperature and pressure, extreme rapidity — often being complete within one microsecond — and most importantly by formation of a shock pulse which accompanies the reaction zone. As with any chemical reaction, there is a critical value of temperature and pressure below which detonation can not occur; this is termed the "critical point". Whereas an explosive substance will decompose slowly at ordinary temperature, with the formation of gases which readily dissipate; at elevated temperature the reaction is considerably speeded. If pressure is suddenly applied at some point in an explosive medium, adiabatic compression results, and the temperature is locally raised. When the temperature becomes high enough the decomposition will be so rapid that the gaseous products do not have time to dissipate, but contribute to a further build-up of pressure. This, in turn, furthers adiabatic temperature rise over a widening area, and with any heat generated by an exothermic reaction, causes a rapid increase in temperature. Both temperature and pressure are spontaneously built up in this manner until the critical point is reached, resulting in detonation. The values of pressure and temperature necessary to create detonation are established by the unusual nature of the process. If temperature alone is raised above the critical point, without sufficient increase in pressure, deflagration or "low-order detonation" occurs. In the true, or "high-order detonation", the shock pulse resulting from the violent decomposition becomes an integral part of the reaction, and itself aids in increasing the detonation

Jan 1, 1961

By OTTO HERRES

TITANIUM is estimated to be the ninth most plentiful element, ranking after iron, aluminum, and magnesium, and ahead of copper, lead, and zinc. Vast quantities of titanium are widespread throughout the world in ore deposits and beach sands. Before the war, processing plants were operated in England, France, Italy, Czechoslovakia, Norway, Russia, Australia, United States, and Japan. In spite of its widespread occurrence, however, the U. S. Department of Justice has held the titanium industry to be a world monopoly and action was taken in the Federal court during the summer of 1945 to enjoin international patent and marketing agreements and to restore free competition. Possibly the rather surprising lack of public familiarity with this industry of international importance arises from its astonishingly rapid development and growth in the strong hands of some of the greatest chemical companies in the world, including the important foreign companies, Imperial Chemical Industries (British), Montecatini (Italian), I. G. Farben (German), and Titan Kogko Kabushiki Kaisha (Japanese). The rapid growth of the titanium industry in the United States is indicated by a tenfold increase of ore imports in the 1930 to 1940 decade before the war began to affect shipments from overseas. The fact that the industry formerly derived practically all ore for chemical processing in American plants from foreign sources probably also accounts for lack of general public knowledge of titanium. In 1939, to meet the requirements of increasing demand for the white pigment. titanium dioxide, more than 250,000 tons of titanium concentrates moved to this country, principally from the Travancore coast of India where the ilmenite concentrate from the beach sand runs as high as 60 per cent in titanium dioxide. Global warfare put a stop to shipping and thus gave rise to the development of titanium mining on a substantial scale in the United States during 1941.

Jan 1, 1946

By WILKES BARRE

AS PREVIOUSLY announced, the semi-centennial meeting of the Institute is to be held at Wilkes-Barre, Pa., on Sept. 12, 13, 14, and 15. An interesting program of technical sessions and excursions is now being prepared by the Local Committee. At the time of going to press the program had not been completed in sufficient detail to permit its being pub¬lished in this number. The detailed program will be published in the September MINING AND METALLURGY, which will be printed in time to be distributed before the Wilkes-Barre Meeting. It may be said in advance, however, that the Com¬mittee has progressed so far in its work that we are assured of one of the -most notable meetings the Insti¬tute has held and that members will miss a rare .treat if they do not attend. The many trips and excursions, as well as the banquet, will be -given to the members as a compliment from the members of the Local Com¬mittee. . . The paper by Howard Eavenson on the Lynch Plant of -the United States Coal and Coke Co. will be illustrated by lantern slides and moving pictures. One of the most appropriate discussions will be that opened by Prof. J. F. Kemp on the Stratigraphy of the Anthracite Region; this also will be amply illustrated.

Jan 1, 1921

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By W. P. Sykes

In connection with a study of tungsten steels, Honda and Murakamil reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. Materials The iron powder used in preparing the alloys was obtained as follows : Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000" C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 per cent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon. The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly for several days at temperatures up to 1500' C. and for shorter periods

Jan 1, 1926

By H. C. Heard

The review by Professor J. C. Jaeger (Chapter 1) briefly summarizes and discusses a select group of papers by various workers dealing primarily with aspects of fracture in brittle rock materials. Professor Jaeger's treatment is primarily concerned with the correlation of phenomenological and theoretical failure criteria with empirical results from short duration tests at ambient temperatures and generally at low lithostatic and interstitial fluid pressures. As engineering rock mechanics becomes more concerned with new techniques of mineral exploration and production at increasingly greater depths in the crust, it is well to be aware of the effect of the environment -that of the superposed stress field upon the lithostatic and interstitial fluid pressure, the temperature and the duration of the loading upon the failure of rocks either by fracture or flow. All results to be discussed here are from laboratory tests on small homogeneous samples, thus caution should be used in the direct extrapolation of these results to large inhomogeneous rock masses having quite different boundary conditions in the earth. The purpose of this supplement is to briefly point out the major effects of these parameters as examined singly, with all others held constant, and to cite some recent results which apply to the main theme on the brittle failure of rocks. The total stress field imposed upon a small volume of porous and permeable rock in the earth's crust may be thought of as the sum of an applied differential stress, plus a lithostatic pressure, plus an interstitial fluid pressure. The differential stress portion may be completely specified by nine components, six shear and three normal. If the small volume element is in rotational equilibrium, by suitably choosing our coordinate axes we may resolve these nine components into the three principal com-

Jan 1, 1967

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or book- keeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. T he emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1964