Search Documents

By Gearge C. Wallick

This paper describes experimental procedures for the calibration of capillary tubes to be employed as comparison standards in gas flow-rate measurements and considers several types of flow which were observed in the calibration of seven capillaries of varying diameter. It is shown that under certain experimental conditions deviations from Poiseuille flow are observed which may not be attributed to turbulence, and that this flow behavior may be described empirically by introducing the classical kinetic energy correction into the Poiseuille equation. INTRODUCTION Techniques have been developed for the measurement of the volume rate of flow of nitrogen through glass capillary tubes as a function both of the differential pressure applied and of the absolute gas pressure. Capillary tubes thus calibrated are frequently used to determine the rate of gas flow through a porous sample in the measurement of slip-corrected permeability. The purpose of this note is to describe the calibration procedure and to discuss some observed deviations from the ideal flow behavior predicted by the Poiseuille equation. EXPERIMENTAL PROCEDURE The volume flow rate of nitrogen as a function of the differential pressure was determined experimentally for a series of seven glass capillary tubes of varying diameter. As is shown in Table 1, the capillary radii in the series ranged from 0.004 cm for K1 to 0.07 cm for K7. The capillary tubes were cut from capillary tubing purchased on special order from several manufacturers and the bore radii were determined by microscopic measurement. The gas volume flow rate was measured for each capillary tube at a series of differential pressures in the range from 0 to 3 cm of mercury and at average absolute pressures of 1.0, 2.5, 4.0, and 6.0 atm. Experimental Procedure for Small Capillaries A schematic diagram of the apparatus used to calibrate the three smallest capillaries, Kl, K2, and K3, is shown in Fig. 1. By means of a standard Ruska Instrument Corp. volumetric pump (equipped with a synchronous motor drive, two stages of gear reduction, and a quick-change lathe gear box), nitrogen was displaced by mercury from a metal cell immersed in a constant-temperature bath. The pump, the line to the cell, and a part of the cell were filled with mercury. As mercury was forced into the cell, it displaced nitrogen which passed through the capillary tube being calibrated and into a large container with a volume of approximately 30 liters. Since the volume of this container was very large compared to the total volume change of the gas resulting from the action of the displacement pump, the absolute pressure of the system was essentially constant throughout any one run. Prior to any determination this pressure could be set at any desired level by means of an auxiliary nitrogen cylinder. The differential pressure across the capillary was measured with a Meriam Red Oil manometer and recorded together with the corresponding pump displacement rate which was equal to the gas flow rate. By repeating this process for a series of different displacement rates at each of the absolute pressures of interest, the data necessary for plotting the calibration curves for capillaries K1, K2, and K3 were obtained. All calibration measurements were made in a constant temperature room to minimize errors due to temperature fluctuations. In each run. the flow was maintained until equilibrium was established. Experimental Procedures for Large Capillaries The flow rates through Capillaries K4, K5, K6, and K7 required to obtain the pressure drops desired were larger than could be obtained from available constant displacement pumps, and it was thus necessary to employ an alternative calibration procedure. The arrangement of apparatus used in calibrating these capillaries at an average pressure of one atmosphere is shown in Fig. 2. Each capillary was calibrated by flowing nitrogen through the capillary and recording the differential pressure as a function of the flow rate. 'The differential pressure was measured with a Meriam Red Oil manometer and the flow rate was determined by collecting the effluent gas over water at constant pressure and recording the increase in volume per unit time after an equilibrium had been established. Appropriate corrections were made for the

Jan 1, 1953

By Tomek Ulatowski

This presentation discusses the necessary ingredients for the creation of an acceptable credit structure, i.e., the structure that enables the borrower to attract the funding from different groups of lenders. As the amount of debt in the capitalization of new projects increases, it becomes quite critical that the mining venture sponsors obtain funding in a manner which maximizes the project economics. Attention normally is focused on the inherent operating cost characteristics of a venture such as the cost of mining, milling, transportation, smelting, and refining. The projected costs are derived from lengthy feasibility studies often taking millions of dollars and years to prepare. For a variety of reasons as the amount of equity directly provided by the sponsors declines, the balance must be made up from external credit sources. As a result, once the project becomes operational, debt service requirements assume crucial importance. For most new ventures, in the early years of production, the total amount of periodic debt amortization charges together with the projected interest expenses equals or exceeds the total operating cost. Utmost care must be taken, therefore, to reducing these costs which will then increase the chances for the implementation of the project. Project sponsors must carefully evaluate different funding sources in terms of their potential economic impact and, concurrently, evaluate alternative credit structures in order to be able to attract the selected funding vehicles. In this presentation I will discuss credit sources in the order of their relative appeal; i.e., from the standpoint of maximizing rates of return to the project owners. The tenor of the credit, that is the period from signing a loan agreement to the time of last repayment under the loan agreement, is undoubtedly the most important variable in evaluating the attractiveness of debt sources. Therefore, I will begin by discussing debt sources with the longest maturities and will end with a description of credits with relatively shorter tenors. The availability of different funding possibilities will naturally depend on the geographic location of the proposed venture, the creditworthiness of the borrower and the sponsors, the project economics, and finally the actual liquidity conditions in the capital markets at the time that the funds are committed. U.S. LONG-TERM DEBT MARKET - PUBLIC OFFERINGS AND PRIVATE PLACEMENTS The long-lived nature of most mining projects dictates that the majority of the mine financing be raised from long-term sources. In today's world capital markets U.S. debt issues probably carry the longest maturities available. The maturities can range from 5 to 40 years. Various types of long-term corporate debt instruments can be differentiated from one another by their terms, seniority as to claims against the assets of the issuer, legal form, and whether issued privately or through a public offering. The terms of these debt issues vary widely. For example, the interest rate which is typically fixed at the time of issuance, is determined by the credit quality of the issuer, the maturity, the average life, the seniority of the debt, the quality of control covenants or type of assets pledged as security, and other exogenous factors such as: economic policy, general level of interest rates and cur-rent level of financing activity. The entire principal amount of the debt may be due and payable at maturity (known as a "bullet" maturity) or, more typically, through periodic repayments in equal or staggered amounts. Almost all such debt issues allow for prepayment at the option of the issuer, but require varying amounts of repayment penalties. Disbursements are made over a relatively short period after signing of the debt documentation which may not coincide with the actual funding needs of the project. Financial covenants can be quite stringent, covering areas such as the issuer's financial leverage, working capital, payment of dividends and other distributions, merger and acquisition activities, and limitations on the disposition of property. Long-term debt issues may also be distinguished by the seniority of their claims against

Jan 1, 1985

By Samuel B. Christy

The present paper is a continuation of a study of the reductionworks of New Almaden, the first part of which was published under the title " Quicksilver-Reduction at New Almaden," in the Transactions of this Society, vol. xiii., p. 547.* Frequent reference will be made to some of the data there given. The following is an outline of the contents of this paper: I. Condensing appliances used at New Almaden: a. Brick condensers, b. Iron condensers—flues and " water-backs," c. Glass and wood condensers, d. Friction-coudensers—filters and revolving screens, e. Flues, towers, and chimneys. II. Analysis of condensing-systems. III. Temperature of condeusers. IV. Product of condensers. V. Treatment of soot. VI. Losses of treatment: a. Nature of losses, b. Composition, weight, and volume of dry gases, c. Volume of wet gases, d. Specific weight of quicksilver vapor, e. Vapor-loss at various temperatures. VII. Comparison with New Almaden practice. VIII. Comparison with results at Idria, Austria. IX. Comparison with results at Almaden, Spain. X. Future improvements in quicksilver-condensation. I. Condensing Appliances. The complete condensation of mercurial fumes in a large way presents numerous practical difficulties, familiar to all who have had to retort amalgams. In condensing the quicksilver-fumes discharged

Jan 1, 1886

By C. W. Sherman, John Chipman

IN the mathematical statement of the law of mass action, the activity of each substance consumed or produced in a reaction is used to obtain a numerical constant which is characteristic of the equilibrium of that reaction at the given temperature. The activity in many cases is equal to, or proportional to, the concentration. If this is the case, any units denoting concentrations, such as weight percentage or mol fraction, may be substituted in the equilibrium expression. It is even permissible to use mixed units provided only that each unit is that used in defining the activity of the corresponding substance. The indiscriminate use of concentration units in writing equilibrium constants sometimes leads to very erroneous results. On the other hand, what appear to be contradictory results from similar investigations often might be resolved if the activity is the quantity that is used to determine the equilibrium constant for the reaction in question. De-sulphurization serves as an important illustration. Sulphur in lron and Steel The control of the sulphur content of the finished product is one of the oldest and broadest problems in the metallurgy of iron and steel. In general, this control must be exercised through the action of a slag, and for this reason experimental studies of the distribution of sulphur between slag and metal have assumed considerable importance. Under slags of the type found in the basic open-hearth furnace the ratio (% S)/[% S] does not in general exceed about 8. Under blast-furnace conditions, however, de-sulphurization ratios of 50 to 100 are readily obtained, and under laboratory conditions using similar slags, the ratio may be as high as 400. The fact that blast-furnace metal is much more readily desulphurized than is molten steel rests upon two distinct phenomena. The first of these is connected with the slag reaction. In the open-hearth furnace, the equilibrium in the following reaction places a definite limit on the sulphur content of the slag: S + 0-- = 0 + S- - where the symbols underlined indicate elements dissolved in the liquid metal, while slag constituents are represented as ions. The high oxygen content of the open-hearth bath prevents this reaction from proceeding far enough to effect good desul-phurization. In the blast-furnace process, however, the oxygen activity is limited by the presence of carbon in the metal and in the coke bed and the controlling reaction becomes: S_+O- + C_=S- + CO(gas) [2] The second phenomenon which contributes to the easier desulphurization of blast-furnace metal is the effect of high concentrations of other elements. These elements, notably carbon, silicon, and phosphorus, increase the thermodynamic activity of sulphur several fold. As a result of this increase, the escaping tendency of sulphur from the metal phase is increased and its removal facilitated. Previous Studies It becomes, therefore, a matter of importance to determine the effects of various elements upon the activity of sulphur in the melt. The experimental approach to this problem has been made through the equilibrium between sulphur in the melt and gaseous atmospheres containing hydrogen and hydrogen sulphide. The reaction and its equilibrium constant are written as follows: S + H2(gas) =H2S(gas);K1 = -- [3] Pn2 • as where the symbol a, represents the activity of the sulphur in solution in the metal. The understanding of the chemical behavior of sulphur in steel and pig iron rests on a firm knowledge of the binary system Fe-S. A number of studies of the equilibrium have given closely agreeing results from which the activity and free energy of the dissolved sulphur may be found. The recent paper by Sherman, Elvander, and Chipman1 includes a discussion and quantitative comparison of the results of several of the significant researchesr-" on dilute solutions of sulphur in iron. The results of this study indicate that the relationship between the ratio Ph,s/p+ and the percentage of sulphur in solution is not a linear one. This

Jan 1, 1953

By H. C. Fiedler

The development of cube-on-edge secondary re crystallization texture in Si-Fe strip depends upon the ability of inclusions, such as manganese sulfide, to restrain nomal grain gvowth. The ability of inclusions to perform this function is shown to depend upon their size and distribution. The desired uniform dispersion of many small inclusions is obtained by controlling the cooling rate from above the solution tempmature of the inclusions or, alternatively, by drastic 'quenching from above the solution temperature followed by heat treating at a lower temperature. The development of the cube-on-edge secondary recrystallization texture in Si-Fe strip depends upon both establishing the proper primary recrystallization texture and having inclusions to restrain normal grain growth. It has been suggested that the first requirement is met with a texture which, though weak, is near (110)[001]. A mechanism for secondary recrystallization originally proposed by ielsen' is consistent with the presence of this primary texture. It is visualized that a secondary grain appears where two adjacent grains happen to be sufficiently similar in orientation to be capable of behaving as a single large grain. This pair of grains will grow at the expense of its smaller neighbors as a consequence of its having lower grain boundary free energy. Other explanations of the origin of the secondary recrystallization texture have been offered,' and it can be concluded that the mechanism is not fully understood. Nevertheless, it is apparent that operationally the necessary primary recrystallization texture is obtained simply by interposing an anneal during the cold reduction to final gage. The role of inclusions in the development of the secondary recrystallization texture has been demonstrated by May and Turnbull4 in a comparison of a high-purity heat and a heat containing manganese sulfide. They showed that the driving force for secondary recrystallization is inversely proportional to the diameter of the matrix grains and that the function of the inclusions is to maintain a small matrix grain size. Other inclusions, such as various sul- fides,')' silicon nitride,8 and vanadium nitride,' titanium carbide,'' and vanadium carbide," have been shown to be effective in promoting secondary recrystallization to the cube-on-edge texture. There is also evidence that silica inclusions in Si-Fe strip made by powder-metallurgy techniques perform this function.' This report is concerned with the second of the two requirements for secondary recrystallization, namely the importance of the metallurgical control of the size and therefore number of inclusions. While the concepts involved are simple, they are fundamental to the making of this material. EXPERIMENTAL PROCEDURE A heat containing 3.27 pct Si, 0.026 pct S, 0.06 pct Mn, and 0.004 pct C was made in an air induction furnace from electrolytic iron, 98 pct ferro-silicon, electrolytic manganese, and iron sulfide. The heat was divided between graphite and baked-sand molds with a cavity 2-5/8 by 5 in. and with walls 2-3/4 in. thick. Slabs, 1 in. thick and 2-5/8 by 5 in., were cut from the ingots and hot-rolled either in the as-cast condition or after one of the heat treatments described later. After pickling, the 80- to 100-mil-thick hot-rolled band was, unless otherwise noted, heat-treated for 5 min at 900°C before being cold-rolled to 25 mils. After a heat treatment of 1 to 3 min at 860°C, the strip was cold-rolled to 12 mils, the final thickness. The percent cube-on-edge texture was determined by dividing the maximum torque as averaged from four samples by the maximum torque of a 3-1/4 pct Si-Fe single crystal having the (110) plane in the plane of the sample. The torque measurements were made in a field of 1000 oe on 1-in.-diam disks. RESULTS AND DISCUSSION The importance of the thermal history of the ingot is evident in Fig. 1 from the appearance of strips heat-treated in a temperature gradient. The sample

Jan 1, 1964

By J. S. Vanick

An extremely hard, tough, and strong, white or chilled cast iron has been applied for the past several years to industrial and mining services in which its unusual properties have been confirmed by its ability to deliver in many instances much better performance than plain chilled iron, or other wear-resistant materials. It is being produced regularly by alloying a good base composition of chilled or white cast iron with essentially 4 to 6 per cent of nickel and 1 to 2.5 per cent of chromium. Such a material can attain a hardness exceeding 600 to 750 Brinell as against 380 to 530 for corresponding grades of plain chilled iron. The strength is approximately doubled and the toughness significantly increased. These properties make it especially useful for many applications requiring a high hardness for resistance to wear, abrasion, attrition, deformation; to some extent to high compressive loading and to a lesser but important degree to corrosive action. A wide variety of commercial castings is being successfully produced from this iron, ranging in size from the small grain-grinding plates or burrs through medium-sized castings such as sand pumps up to large, heavy castings such as rolls for metal rolling or cement grinding. The composition of this white cast iron may be roughly bracketed within the range shown in Table 1.

Jan 1, 1933

By P. Chiotti, J. T. Mason

Thermal, X-ray, metallographic, and resistivity data were obtained to establish the phase diagram for the Yb-Zn system. Six intermetallic compounds and five eutectics have been identified. The compounds position at 695°C. No evidence for the compound YbZn,, was observed. Whether this compound is stabilized or inhibited by small amounts of impurities is uncertain. SEVERAL aspects of the Yb-Zn system have been reported in the literature. Much of this work deals with the crystallographic identification of some of the compounds. The YbZn compound has been reported by Iandelli and palenzonal and the YbZn, structure and thermal data for the composition range between YbZn and Yb3Znll have been reported by Michel et al. A compound of uncertain stoichiometry in the range 60 to 68 wt pct Zn with a cubic structure has been reported by Kuz'ma et aL4 The YbzZn17, YbZn,,, and YbZn13 compounds have been reported by both Kuz'ma et a1 and Iandelli and Palenzona.' YbnZn17 has also been identified by Laube. This investigation was undertaken to establish the phase diagram of this system. Ytterbium in many respects behaves as an alkaline earth rather than a rare earth metal6 and it is of interest to note the resemblance between the Yb-Zn system, the Ca-Zn,' and typical rare earth-zinc systems.g'10 MATERIALS AND EXPERIMENTAL PROCEDURES The materials used in this investigation were Ames Laboratory ytterbium and Bunker-Hill slab zinc, 99.99 pct pure. Analyses of the ytterbium showed 38 ppm Ta, 82 ppm 0, and 15 ppm N with Ca, Cu, C, Mg, Al, Si, Cr, Fe, Ni, Sc, Y, Er, Tm, and Lu all less than 50 ppm. The ytterbium was dehydrogenated by heating in tantalum under vacuum for 8 hr at 900°C. The metal was kept under argon except when being cut with shears and when being weighed. Tantalum was found to be a suitable container for alloys in the composition range between ytterbium and Yb2Zn17. With higher zinc concentrations the tantalum was penetrated by the alloy and failed after several days at temperatures of 600" to 700°C. Approximately 20 g of zinc and ytterbium metal were sealed under argon in *-in.-diam tantalum cruci- bles equipped with thermocouple wells. The crucibles were in turn sealed in stainless-steel jackets. The alloys were equilibrated in an oscillating furnace and given various heat treatments in a soaking furnace. The steel jackets were removed and differential thermal analysis data were obtained under an atmosphere of argon. The thermal analysis apparatus was calibrated against the melting points of pure zinc, aluminum, silver, and copper and found to give thermal arrests within 1°C of the accepted melting temperatures for these elements. The thermal analysis apparatus has been described in an earlier paper.g Alloys were further heat-treated as necessary and subjected to metallographic examination and X-ray diffraction analysis. Most alloys were etched with Nital (0.5 to 10 pct nitric acid in alcohol). EXPERIMENTAL RESULTS The results of the thermal analysis are summarized by the points on the phase diagram, Fig. 1. Six compounds and five eutectics were observed. The eutectic temperature and compositions in weight percent zinc are 491°C and 12 pct, 645°C and 32 pct, 687°C and 54 pct, 742°C and 67 pct, and 750°C and 77 pct. The compounds YbZn, YbZn2, Yb2Zng, Yb2Zn17, and YbZnll melt congruently at 650°, 751°, 75Z°, 754", and 755"C, respectively. The compound Yb3Znll undergoes a peritectic decomposition at 695°C. The transformation and melting temperatures for the ytterbium were observed to be 797" and 817°C. re-

Jan 1, 1969

By H. S. McKnight

One phase of Canada's rapid development in mining and metallurgy during the past few years has been the creation of Canadian Copper Refiners Ltd., and the establishment of its modern electrolytic copper refinery at Montreal East, Quebec. Canadian Copper Refiners Ltd. is made up of three well-known metal firms whose combined activities cover the entire industry from the mine to the market. They are Noranda Mines Ltd., Toronto, Nichols Copper Co., New York, and British Metal Corporation, Ltd., London. Noranda Mines is the principal owner and provides the greater part of the raw material received by the refinery for treatment. Nichols Copper Co. designed and built the plant and is operating it under contract. British Metal Corporation acts as sales agent and markets the refinery's products. Montreal East was chosen as the site of the new refinery only after a careful survey had been made of the entire eastern part of Canada. The location chosen offers many advantages, chief of which arc the relatively low costs of power, labor, fuel and bupplies, and the fact that it is situated on Montreal harbor, the nearest seaport to the points of origin of the ram materials. All incoming material is received by rail. A majority of the plant's product is exported through the port of Montreal to European markets, being handled to the docks in railroad cars. A large proportion of the product is delivered by means of an industrial railway to the adjacent rolling mill of the Canada Wire & Cable Co., Limited. The refinery was designed to treat primarily the copper produced by Noranda Mines, Ltd. and Hudson Bay Mining &. Smelting Co., Ltd., and its rated capacity is 75,000 short tons per year. A general layout of the plant is shown in Fig. 1. Its capacity can be readily doubled, as shown by the dotted lines. Figs. 2 and 3 are sections taken through the furnace department and the tank house respectively. Except for the main office and laboratory and an auxiliary building containing the stores, warehouse, change rooms, compressor room and machine shop, the entire plant is under one roof. The type of building construction consists of reinforced concrete foundations supported on concrete piles, a steel structure covered with Robertson Protected Metal siding and a 3-in.

Jan 1, 1934

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies' of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed, to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1,2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1947

By A. P. Woods, J. A. Elias, A. J. Heckler

A method is described by whichX-ray pole figures and axis density figures may be plotted automatically. The X-ray data are obtained using a Siemens texture gonionleter and the Schulz reflection method. Composite sampling methods are used to obtain a full quadrant of the pole figure. The contour lines of the pole figure and axis density figures are drawn using a computer-controlled x-y plotter. The computer program used to draw the contours was obtained from ZBM. POLE figures used to describe crystallographic orientations of poly crystalline sheet materials are usually plotted manually from X-ray diffraction output in the form of a strip chart recording of the intensity distribution of a given crystallographic pole in physical space. Today's computers and associated plotting equipment now make it possible to plot pole figures and axis density figures automatically. Inverse pole figures have been determined by mathematically "inverting" X-ray pole figure data.'-' In general, these methods require complicated, time-consuming numerical calculations. A more economical but less accurate method is to determine the axis densities of low-index crystallographic poles using an X-ray diffractometer. When these axis densities are plotted in a unit stereographic triangle contour lines can be drawn to represent the axis density distribution. This can now be done automatically. Computers were used to plot pole figures by a method developed by Holland, Engler, and powers.' In their method intensity ratios based on a random standard sample were obtained from a strip chart recording, and the stereographic (x, y) coordinates of these ratios were determined by a computer. Symbols characteristic of different intensity ratio levels were then plotted using an automatic x, y plotter and intensity contours were drawn manually. The present paper describes a method by which pole figures and axis density figures have been automatically plotted from digital data obtained from a Siemens X-ray unit. Plotting was accomplished using an IBM 1620 computer and a Calcomp 563 digital plotter. COMPUTER PROGRAM The computer program was obtained from IBM Systems Reference Library, No. 1620-CS-05X, and was designed to plot contour maps from randomly distributed data. It consists of a set of twelve separate subprograms, four of which were used in this work. The program takes a given distribution of data points and by a numerical method determines the values at mesh points of a square grid system superimposed over the input data. The output data from this program is in a form suitable for input to the contour plotting program. A smoothing program is also available which calculates new mesh point values from a continuous function fitted to neighboring mesh points. The degree of smoothing depends on the number of points around a given grid point which are used to adjust or smooth the grid value. The contour plotting program is designed to allow the user to specify the interval, scale, and annotation of the contours to be plotted. EXPERIMENTAL PROCEDURE Pole Figure Data Points. Diffracted X-ray intensities were determined using a Siemens texture goniometer and the schulzs reflection method. Due to geometric

Jan 1, 1968

By James Johnston

Synopsis.-A description of the working of the mills of this company and the metallurgical practice in vogue, by which a remarkably. complex silver ore, averaging 54 oz. of silver per ton (run-of-mine ore), is treated to give a 95.66 per cent. extraction. The main features of the, processes are: The cyanide amalgamation of the high-grade ore. The cyanide treatment of the low-grade ore, after extremely fine grinding and close classification, in a caustic soda solution. The use of a wet desulphurizing process to break up refractory silver minerals. The substitution of aluminum dust for zinc dust as a precipitant. The recovery and shipment of over 13,000,000 oz. of silver in bullion at. 997 to 999 fine since this metallurgy was inaugurated, about 2.5 years ago. On the completion and successful operation of the mill to treat their . high-grade ore,1 the Nipissing Mining Co., under the general management of R. B. Watson, started a series of investigations of the possible treatment of the low-grade ore by the cyanide process, so that they would be in a position to market only silver bullion. These tests were run in July, 1911, on a large scale, by G. H. Clevenger, on an average mixture of Nipissing ore. The results obtained by a partial amalgamation followed by cyanide treatment gave an extraction varying from 90 to 93 per cent. and were sufficiently encouraging to warrant Charles Butters, the company's Consulting Metallurgist, in recommending that the new low-grade ore mill under contemplation should be a cyanide mill, instead of a concentrator. The cost of such a mill, capable of treating 200 tons per day, to obtain a 90 per cent. extraction at a working cost of $3 per ton of ore treated, was estimated at $250,000.

Jan 1, 1914

By H. R. Peiffer

The increase in electrical resistivity, ?pT,at 78°K was measured as a function of elongation, E, at 78°K for a 2 pct (approximately) by weight finely divided alumina in silver material. The amount of increase in electrical resistivity (?pT) is a function of the amount of alumina present and can be represented by: ?pT = cen where c and n are constants. The constant c increases and the exponent n decreases with increasing alumina content. Approximately 33 pct of the resistivity increase is recovered upon annealing at room temperature. RECENTLY, dispersed phase alloys' have shown promise for use at elevated temperatures. These materials have a high creep resistance, a high-temperature strength considerably above that of the pure matrix, and a high electrical conductivity. These materials also show other properties such as retardation of re crystallization and resistance to flow even above the melting point of the matrix.' It is believed that high-temperature creep is retarded in these materials because the dispersed phase blocks the motion of dislocations. According to schoeck3 and also Weertman,4 the rate controlling process is the climb of dislocations around the dispersed phase particles. Any mechanical property of these materials, or any other material for that matter, can be explained on the basis of defect structures and their interrelations. It would certainly be interesting to learn something about the effect of a dispersed phase on dislocation densities and also their effect on point defect concentrations following cold work. This is the purpose of the research discussed herein. The method used was the measurement of the electrical resistivity as a function of elongation at low temperatures. This scheme has already been applied to the studies of pure metals.5 Electrical resistivity measurements conducted on pure metals such as copper, silver, gold, and so forth, have indicated that defects such as vacancies and dislocations are formed during deformation.5 It has been shown by van Bueren6 that the resistivity change, ?p, should increase with elongation, E, according to the following relation: Ap=Al/2 + B£3/2 where A and B are constants of the system; ?p is in µ? cm. The first term refers to the amount of resistivity change associated with line defects and the second term with the change associated with point defects. A later calculation yielded exponents of 3/4 and 5/4, respectively.6 Manintveld7 has shown that the resistivity of copper increases with strain according to a 3/2 power law, whereas van Bueren has shown that the resistivity of silver increases according to a 5/4 power law. Assuming then that van Bueren's calculations are correct, it appears that line defects contribute very little to the electrical resistivity. There is some doubt, however, as to the validity of van Bueren's expressions for all cubic metals.' In fact, the data on copper and silver are not conclusive. In this in-

Jan 1, 1962

By McQuiston. F. W., E. C. Tveter

Sulfide mineral flotation has been applied to all naturally occurring sulfides and several synthetics. Of even more importance is the fact that economic separations are now being made between sulfides of essentially all the different metals. The variety of methods and minerals involved in such practice make it difficult to characterize them except in terms of general factors which influence the practices used. Ore grade and mineral composition are the major factors determining the processing method and the extent to which processing must be carried to achieve optimum economic return for a given ore. Since the choice of treatment is also affected by such factors as mine location, shipping charges, smelter schedules, each ore is a separate problem even though mineralization may be similar; The dissemination of minerals in the ore naturally determines the fineness of grind required for liberation. However, since grinding costs are a major part of most milling costs, emphasis has been placed on means of rejecting gangue minerals at the coarsest size possible. This has led to increased flotation of middling products or bulk concentrates for subsequent regrind and retreatment. Reagent development has also played an important part in present plant practice. Relatively few new frothers and collectors have found application during the past 25 years and many have disappeared. In general practice, re- agent combination choice is now fairly consistent with the type of collector being chosen on the basis of the mineral to be floated, the frother on the basis of pulp alkalinity, and the modifiers primarily on the basis of minerals to be rejected. REPRESENTATIVE FLOTATION PLANTS The milling operations described in this chapter have been selected primarily to illustrate these differences in ores and processing methods for the major types of ore minerals. The compositions of these minerals are shown in Table 1. These concentrators were chosen as representatives, both on the basis of geographic location and mineral content of the ore treated. At least one mill is included from each of the major producers, but the primary object was to show the practice employed for the various ore minerals and the different approaches to the middling problems encountered. The individual plants which have contributed data to this study are listed in Table 2, with a summary of their operating data, and are discussed in the order shown.

Jan 1, 1962

By M. B. Bever, A. K. Jena

Equations for the heat effects of additions of mixtures of multicomponent phases to a solution have been derived in terms of the enthalpy interaction coefficients. By these equations and the measured composition dependence of the heat effects on addition of mixtures of Ag-Cd solid solutions and elemental gold to liquid tin-rich solutions, values of the enthalpy in-teraction coefficients in tin-rich solutions at 541°K have been obtained. Analysis of these results in terms of the regular solution theory and the quasichemical theory suggests that near the melting point of the solvent association in the solution becomes important. SEVERAL recent papers have discussed the nature of dilute solutions on the basis of measured enthalpy interaction coefficients. l-3 These coefficients contribute to the understanding of the constitution of solutions and can be used for the evaluation of thermo-dynamic data of multicomponent systems. Their experimental determination, however, is laborious. This communication reports values of the enthalpy interaction coefficients of silver, cadmium, and gold in liquid tin-rich solutions obtained from the measured heat effects of additions of mixtures of Ag-Cd solid solutions and elemental gold to liquid tin-rich solutions. These measurements were made in the course of the determination of the heats of formation of Ag-Cd solid solutions reported in a concurrent publication.4 THE HEAT EFFECT OF AN ADDITION TO A SOLVENT This analysis is concerned with the addition of a mixture of multicomponent phases from the temperature To to a solvent of known composition at temperature T. If Nmixture << Nsolvent, where N designates the gram-atoms involved, the heat effect per g-atom of mixture added can be expressed as (HT - HT )i = difference in heat contents of component element i in the mixture at T and To Q = heat effect on solution of the mixture at temperature T Also1 Q = S Xi [2] where ?Hi ,T,x = relative partial enthalpy per g-atom of i in solution at temperature T and composition of the solution x x = average of the atom fractions of the added material in solution before and after the addition The relative partial enthalpy ?Hi per g-atom of an element i in a dilute solution composed of a solvent 1 and the solutes j = 2, ... m is related to the interaction coefficients by the following equation5 ?Hi - ?Hi-?Hi,x1-1 + S n1ixj+ . . . +S...S...S nrixn2... Xnji...Xnmm+... [3] vhere Xj = atom fraction of solute j in the solution nri = the rth order enthalpy interaction coefficients, which can also be represented by the more general designation5 L(i)n2,n3...nm and nj may have any positive integral value or zero. For identification of various rth order interaction coefficients, nri is written as nn2i2,...nij,...nmm. Eqs. [1], [2], and [3] combine to give the following general equation for the heat effect on addition of a small quantity of a mixture to a large quantity of a dilute solution n = _?ga ?Ha,To + ? Xi(HT - HT o)i a. i + ?xi?Hi,X,i?1 + ??xnjixj + . . . + ???. . .?. . .?xinrix2n2. . . xnji. . . xnmm+ . . . [4] The first term on the right-hand side of this equation is the heat of decomposition at the addition temperature of the phases present in the mixture, the second term is the heat required to raise the temperature of

Jan 1, 1970

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn&apos;s for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

Page Bronze Bearing Metals. By G. H. Clamer............... 162 Pennsylvania Railroad Anti-friction and Bell Metals. By F. M. Waring .. 166 The Tin-plate Industry. By D. M. BUck. Discussed by G. H. ClameR, J. W. RICHARDS............................ 168 The Aluminum Bronze Industry. By W. M. Corse............ 171 Bronzes, Bearing Metals, and Solders. By G. K. BURgess and R. W. Woodward. Discussed by G. H. Clamer, R. T. Roberts......... 175 Babbitts and Solder. By G. W. Thompson................ 184 The Cadmium Supply of the United States. By C. E. Siebenthal. Discussed by M. L. Lissberger, C. W. Hill, F. F. ColcoRd.......... 185 Solder, Its Use and Abuse. By M. L. LissbergeR............ 192 Bronze Bearing Metals G. H. ClameR,* Philadelphia, Pa.—Unfortunately, prior to the war no serious attention was given to the conservation of tin, notwithstanding that this country is practically dependent upon outside sources for its entire tin supply. Tin is of vital importance in many industries, but it is surprising how many and how excellent are its substitutes when we become acquainted with them. Tin has always been a relatively high-priced metal, and it is part of the human attitude to associate high prices with high standards; it is not until the price of a commodity becomes well-nigh prohibitive that we hunt for substitutes, because the idea of substitution seems always to involve an assumption that the substitute must necessarily be inferior. The history of the development of bearing bronzes is a striking example of this policy. In the early days, copper-tin alloys were almost universally used, the idea then being prevalent, which is still held by many, that a bearing to resist wear must be hard, and the harder the better. The favorite bronze bearing contained 90 per cent. copper and 10 per cent. tin; frequently, in service which was considered severe, even higher proportions of tin were used. Such hard alloys have great resistance to compression, but as a rule they had a very wide factor of safety in this

Jan 1, 1919

By M. J. Sinnott, J. C. Tobin

A technique for collecting and analyzing the small quantities of gases desorbed on heating metal powders has been developed. The gases collected from copper powders of various types of manufacture have been analyzed and found to contain H2O, CO2, and SO2. The quantities of gas evolved vary from 0.05 to 1.0 milliliter, under standard con-ditons of temperature and pressure, per gram of powder. The source of the gas has been traced to surface films on the powder. IN the powder-metal industry it is recognized that the presence of gases in the powders affects the processing and resulting properties of the sintered product. Several sources for these gases are possible; namely, chemical reactions with the sintering atmospheres, inclusion. of gases during compacting, dissolved gases in the metal powder, and sorbed gases on the metal-,powder surfaces.1, 2, 3 Since the quantities of the gases are relatively small, no direct attempt has been made to collect and analyze them nor to isolate their source. The work that has been done has been concerned with the dimensional stability of the product., its porosity, density, or mechanical and physical properties. Conclusions are drawn on the basis of studies of this type as to the probable effect of gases on these properties. 4, 5, 0 In the present investigation an attempt has been made to obtain quantitative data on the analysis and quantities of gases associated with copper powders manufactured in different ways. Apparatus was constructed to collect gases evolved from loosely packed powder samples on heating to various temperatures under a reduced pressure of helium. The powders were outgassed thoroughly in a vacuum prior to starting the collection operation in order to eliminate mechanically entrapped gases and to prevent the possible reaction of the powder with these gases. Experimental Procedures Materials—The major portion of the investigation was carried out on a single heat of water-atomized, oxygen-free, high-conductivity copper. A relatively coarse fraction of this powder, 20 to 100 mesh, was tested as a mixed powder and as various graded size fractions. The microstructure of this powder showed equiaxed grains and was clean and free from oxides and oxide eutectic. The particle size, as determined

Jan 1, 1959

By William H. Shockley

Though China has been widely explored by mining engineers during the past dozen years, comparatively little has been published concerning its mineral resources. The few moilographs scattered through the transactions of various societies contain far less information than the private reports made to the numerous syndicates which have sent out engineers. The best general account of the geolopy and mineral resources of China is to be found in the works of von Richthofen,&apos; a remarkably gifted observer. The observations recorded here in this paper were made in the service of the Pekin Syndicate (which has kindly given me permission to publish them), during the first months of 1898, among the coal- and iron-fields of southeastern Shansi. This is one of the largest anthracite-regions known, the area being

Jan 1, 1904

By David White

Attention has been given to the sources and supply of the raw vegetal matter and the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic dct,ris, and of the biochemical changes undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of this debris, and the deposition, as sediments, of the undecom-posed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal so1ution. Biochemical Changes End in Peat Formation The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly uncon-solidated, and their water content is great, amounting to over 85 per cent, near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed. Geochemical and Geophysical Changes in Buried Deposits Subsequent Changes " Dynamochemical" The changes which subsequently take place through dehydration, lithification, and simultaneous progressive chemical alteration, by which organic sediments are advanced to brown lignite, subbituminous, bituminous, semianthracitic, and graphitic ranks, are geochemical and geophysical, and the process, which really is metamorphic,2 takes place under dynamic influences. In fact, the essential changes, including loading,

Jan 1, 1925

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

A mathematical model is developed for flotation in a countercur-rent column where continuously generated air bubbles rise through a downward flowing pulp. The model is based on the assumption of axially dispressed plug flow of both the liquid and air-bubble phases. An appropriate flotation-rate expression, which takes into account the changing concentration of solid particles on the bubble surface, is formulated and applied to the column flotation process. Although a complete solution of the resulting equations is not possible for the general case, solutions for specific limiting cases have been obtained. From these, it is possible to predict theoretically the dependence of the column performance on certain variables. Specifically, concentration profiles as a function of height in the column have been calculated for various values of the characteristic dimensionless parameters. The effect of axial dispersion on the perforance of the equipment is pointed out. In recent years, there has been considerable progress in delineating the fundamental physicochemical principles underlying the unit operation of flotation and in advancing methods for kinetic analysis and process modeling of flotation.&apos; In general, nearly all such process research has been concerned with the analysis of conventional flotation equipment and circuits. From these investigations, the possibility of developing and designing flotation apparatus for more efficient separation appears limited with conventional equipment. How- ever, recently there has been an attempt to apply coun-tercurrent flow techniques to flotation in the context of a flotation column.- some of the results from pilot-plant studies2 indicate possibilities for success of this process at least in obtaining higher-grade concentrates though not higher recoveries. A flotation column operates on countercurrent principle in which bubbles continuously generated at the bottom of the column rise through the downward flowing slurry. A schematic diagram of the flotation column is shown in Fig. 1. The physicochemical principles of bubble-mineral attachment, using this flotation column, are essentially the same as those which prevail in conventional equipment, the only differences being in the flow patterns of the various phases. The salient operating feature of the column as compared to those of a conventional cell is that neither mechanical nor turbulent pneumatic agitation is employed. The column is

Jan 1, 1971