Search Documents

By A. W. Hull

The new valves described in this article are the latest product of the Research Laboratories of the General Electric Co. Some of them are still in the laboratory stage, others have already found important applications. Some of the larger ones, which have graduated from the laboratory, are waiting for their apprenticeship in industry, there to refine their frailties and complete their preparation as electrical servants. The career that awaits them, though dimly foreseen, appears fascinating. And as surely as history repeats itself, scenes still more romantic, now beyond the horizon, will unfold as we approach them. This is the romance of science. Counting Electrons Let the smallest tube lead the march of review. It is a special Pliotron, designed to measure currents smaller than any yet detected. It goes by the unromantic name of Pliotron FP-54. Fig. 1 shows this miniature tube—miniature in performance rather than size, for it is the size of an ordinary radio receiving tube. Its appearance has nothing distinctive, except the quartz beads above and below the plate, which support the grid. They minimize insulation leakage. In principle, the FP-54 is like any grid-controlled high-vacuum electron tube; but in structure and operating characteristics it is entirely special. An extra "space-charge" grid, maintained at 3 volts positive with respect to the filament, holds back the small but pernicious current of positive ions emitted by the filament; the normal plate voltage is 6 volts, grid bias 3 volts, thoriated-tungsten filament temperature 1700" K., plate current 40 microamperes. These conditions are essential to the avoidance of grid-currents, which may consist not only of insulation leakage and positive ions from the hot filament and from residual gases, but of high-speed electrons from the filament, photo emission from the grid due to the light of the filament, and electron emission caused by X-rays generated by the impact of electrons on the plate.

Jan 1, 1932

By John H. Bassarear, A. A. Dor

INTRODUCTION Primary grinding mills as defined in this paper, are autogenous or semi-autogenous rotating, tumbling mills having a coarse feed with a top size usually varying from 150 to 300 mm (6 to 12 inches). Most frequently, the feed to these mills is the product of primary crushing plants but in some cases run of mine ore is used as feed such as at Benguet, McDermitt, L-Bar Sohio, Bear Creek and others. The size of the largest lumps in the mill feed is principally determined by limits set by the mill feed trunnion diameter and by the type and size of conveying equipment used for handling and of bins and stockpiles used for storage. The use of primary mills in mineral processing plants has expanded very significantly in the last twenty years, and they have been successfully applied to the treatment of a wide variety of ores in both wet and dry grinding applications. In the present state of technological development for primary grinding mills, there is a wide choice of acceptable options with respect to type and size, grinding flowsheet and grinding media. The choice of the optimum combination which would result in the most satisfactory condition of operation, from the standpoint of both metallurgical results and costs, depends on the nature of the ore, the required characteristics of the grinding products and on various geographic and economic circumstances. The effects of such factors and considerations on the choice and sizing of primary grinding mills and flowsheets are reviewed and discussed in the following pages. PRIMARY MILLS SELECTION Inherent Characteristics of Primary Grinding Primary grinding is complex because it involves several comminution mechanisms which occur simultaneously and to some degree interfere with one another. These mechanisms of impact, attrition and abrasion have been described earlier. The relative importance of these three main grinding actions and their mutual balance resulting in a continuous uniform operation of the mill depend to a very large extent on the nature of the ore and its physical properties. Homogenous, single mineral ores will behave quite differently from heterogenous ores consisting of different minerals bound together along defined

Jan 1, 1982

By Richard Akerman

(Translated by FREDERICK PRIME, JR., Professor of Metallurgy in Lafayette College, Easton, Pa.) [THE attention now being paid both in this country and Europe to the greatest economy in the working of the blast furnace, and the eagerness with which all thoughtful men in the iron business look for any new information which will tend to throw light on this sub¬ject, is a quite sufficient excuse for presenting this paper to the Amer¬ican Institute of Mining Engineers.] I. It must be borne in mind that when two bodies unite to form a chemical compound, heat is almost always evolved. In order to

Jan 1, 1873

By John J. Egan, A. B. Kinzel, Walter Crafts

The demands of the petroleum and chemical industries for steels to be used in pressure vessels and similar structures at artificially low temperatures are continually increasing, and the writing of proper specifications with suitable tests becomes increasingly important. Likewise, the selection of suitable steels for such applications is of increasing concern to the metallurgist. It is generally recognized that highly alloyed steels of the austenitic stainless type retain their properties even at very low temperatures and represent the best technological solution of the low-temperature steel problem. However, in many instances less expensive carbon or low-alloy steels suitable for service within limited temperature ranges are available. The problem thus becomes one of defining the various factors involved in the production and fabrication of these less expensive steels and determining the temperature ranges in which their properties justify engineering application. Most of the applications involve welded structures, and the heat effect of welding as well as the nature of the weld metal are matters of prime concern. The first problem that the metallurgist faces is the determination of the type of test to be used as a criterion of the performance of the steel in low-temperature service. It has been generally recognized that the static properties of steel as determined in the ordinary tensile test undergo a gradual and relatively slight change as the temperature of test is lowered in the range of current interest; i.e., from room temperature to minus 120' C. It is further generally recognized that the behavior of steel under impact involving notch sensitivity is definitely affected at the lower temperatures. While the major subject of this paper is the effect of grain-refining deoxidizers, of low-alloy additions and of welding on the low-temperature notched-bar impact properties, an inquiry into the general behavior of steel under low-temperature impact testing is included. This is a pertinent portion of the investigation and the results thereof are

Jan 1, 1937

By W. H. Bassett, C. H. Davis

ALTHOUGH brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other. words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. . In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent. copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,1 the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.

Jan 1, 1928

Jan 1, 1915

By Robert Keeney

Before the outbreak of the war in 1914, the only electric-furnace smelting plant operating on a commercial basis west of the Mississippi River was an electric pig-iron plant in California; rare metal ores were not smelted, concentrates of molybdenum, tungsten, uranium, and vanadium ores being shipped east for reduction. Practically no- chrome ore was being mined, and only comparatively small amounts of manganese ore. Today there are two electric smelting plants in California, one in Washington, one in Iowa, and four in Colorado; two plants are under construction in California, and one in Montana. Ores of manganese, chromium, molybdenum and tungsten are now smelted in the West, and although uranium and vanadium concentrates are still shipped to the East, they will probably be treated in western plants in a short time. The four electric-furnace plants in Colorado are listed in Table 1. TABLE 1.-Electric Smelting Plants in Colorado Capacity, Company, Location Kilowatts Products . Tungsten Products Co Boulder 800 Ferrotungsten, ferromolybdentun. Boulder Tungsten Production Co. . Boulder 400 Ferrotungsten. Ferro Alloy Co Utah Junction 1200 Ferrochrome, ferrotung-sten. Iron Mountain Alloy Co Utah Junction 3000 Ferromanganese. Power for all of these plants is supplied by the Colorado Power Co.

Jan 8, 1918

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By Ian Wark

IN the paper on the development of the flotation process at Broken Hill (Australia) prepared by the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy and published in its Proceedings for 1930 (N. S. 80), it is stated that the concentration of ores by flotation has been established on a commercial basis in Australia since 1904 and that differential flotation was practiced at Broken Hill in 1912. Since then, progress in flotation practice throughout the world has been rapid, and during recent years the knowledge of the reactions between comparatively modern so-called chemical promoters or collecting agents and the mineral surfaces has been broadened by the published accounts off many investigators, particularly those working in American universities. Because of the benefits the Australian mining industry has derived from the flotation process, it was felt that the industry should take some part in the efforts that are being made to extend the knowledge of the principles on which the flotation process is based. Accordingly, early in 1930, three Broken Hill mining companies-the Broken Hill South, the North Broken Hill, and the Zinc Corporation-together with the Electrolytic Zinc Co. of Australasia, Ltd., and the Mount Lyell Mining & Railway Co., established a laboratory in the chemistry department of the University of Melbourne for the purpose of investigating the principles underlying flotation. Subsequently, the Burma Corporation, Ltd., expressed a desire to cooperate. The two authors are directly employed and controlled by these six organizations, and the cost of the investigation is divided equally among them. The research has been carried out under the general direction and in close cooperation with Harry Hey, chief metallurgist for the Electrolytic Zinc Co. of Australasia, Ltd., and the authors desire to place on record their indebtedness to him for his ever willing help and constructive criticism.

Jan 1, 1932

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By B. W. Howlett, M. B. Bever, Somnath Misra

The heats of Formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 and the heats of solution of tellurium and selenium in liquid bismuth have been measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides have been measured in a constant temperature gradient calorimeter. The thermo-dynamic quantities are interpreted in relation to the stability of the compounds and the nature of the solid-liquid transition. THE selenides and tellurides of several elements of Group VB of the periodic system are of interest because of their electronic properties. The compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 are semi- conductors; they also have gained prominence in the fields of thermoelectricity and photoconductivity. However, little is known about their thermody-namic properties. As part of a research program on the thermo-dynamic properties of intermetallic compounds, the heats of formation of the compounds Sb2Se3, Bi2Se3, Sb2Te3, and Bi2Te3 were measured in a liquid metal solution calorimeter. The heat capacities near the melting point, the heats of fusion, and the melting points of the two tellurides were measured in a constant temperature gradient calorimeter. The results, in addition to their intrinsic interest as thermodynamic quantities, contribute to an understanding of the stability of the compounds and the nature of the solid-liquid transition. 1) EXPERIMENTAL 1.1) Materials. Samples of the compounds SbzSe3 and Bi2Se3 were prepared by melting the elements in stoichiometric proportions in evacuated Vycor capsules followed by quenchinn in water. They- were then annealed in vacuum for 12 hr at 550°C. A sample of Sb2Te3, consisting mainly of one large grain, supplied by the Lincoln Laboratory,

Jan 1, 1964

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By B. G. Klugh

(New York Meeting, February, 1913.) THE present paper represents a preliminary investigation of the ultimate structure of iron-bearing materials which have been subjected to heat treatment for the purpose of agglormer-ating the fines, or for chemical changes, or for both. Primarily, the object of this inquiry was to determine the relation of the microstructure of each of these materials-to its specific susceptibility to the action in the blast-furnace. It is hoped that this small contribution will serve as a nucleus to a line of research that will throw some light upon the debated questions involved in blast-roasting. Thus far the investigation has been conducted along lines of analogy of known principles, rather than through the applica-tion of any well-defined system of microscopic petrography. This is obviously due to the fact that we are dealing with materials which are the artificial products of a new art, rather than with the natural materials from which the essence of the pure science has been evolved. In the limited tune allowed for this research, it has been conducted upon those materials the chemical content of which allows of their use commercially in the blast-furnace.

Jan 5, 1913

By D. B. Kibler

Pill Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County this area is approximately 100 miles long and varies from 2 to 30 miles 1n width Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon Marion County, in the year 1888, by Albertus Voight who lived within a few hundred yards of the spring Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County Phosphate was found in many places as "outcrops " Looking for outcrops was the first method used by the early prospectors in searching for deposits Several years passed before any systematic method of prospecting was used EARLY MINING The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from 1/2 to 1-yd capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907 From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers At some places, the overburden was loaded into side-du nip skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine The maximum depth of overburden that could be economically removed by hand labor mules and scrapers was approximately 15 feet About 1905 one of the companies erected a producer-gas powerhouse near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden From the year 1888 through the year 1939, approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for the export trade Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today only three companies are operating These

Jan 1, 1941

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

By A. A. Bauer

The ?-to-? transformation has been studied in zirconium alloys containing 22 to 70 wt pct U. In this range of compositions the ? phase can be retained by quenching. Transformation to ? occurs by a nucleation-and-growth process. The diffusion of atoms to preferred lattice sites to yield a partially ordered structure apparently controls the rate of reaction. Alpha uranium and a zirconium precipitate from the supersaturated E phase initially formed in alloys outside the equilibrium E phase composition limits. ZIRCONIUM-Uranium alloys have long been of interest for reactor-fuel applications because of the low thermal-neutron cross section of zirconium. Considerable information is available on the various properties and behavior of these alloys1 although there had been a number of areas where information was incomplete. As part of a program to provide more detailed knowledge in these areas, the presently reported investigation was undertaken. The constitutional diagram of the zirconium-uranium system is shown in Fig. 1.' The system is distinguished by a region of complete solid solubility between the body-centered cubic ß-zirconium and ? uranium phases and the existence of an intermediate phase in the vicinity of 50 wt pct U. This intermediate phase, designated as E, is reported3 to have a primitive hexagonal structure with a = 5.03 and c = 3.08A. The structure is partially ordered with zirconium atoms at the 0, 0, 0 position and zirconium and uranium atoms located randomly at the 1/3, 2/3, 1/2, and 2/3, 1/3, 1/2 positions. While the E phase may be nominally designated as of UZr2 stoichio-metry, the random distribution of uranium and zirconium atoms permit a considerable range in composition. Of interest in the research performed were alloys in the range from 20 wt pct (10 at. pct) to 70 wt pct (47 at. pct) U. In this range of compositions the body-centered-cubic ? phase can be retained either completely or partially on quenching. The nature and kinetics of transformation of the ? phase were the subject of study. Proceeding concurrently with the presently reported work was an investigation by Kearns4 which has since been reported. Kearns studied alloys containing 50 to 60 wt pct U prepared from sponge zirconium. While the work reported here is for alloys prepared from crystal-bar zirconium and the techniques of study are to some extent dissimilar to those employed by Kearns, general agreement so far as results and interpretation can be reported. Experimental Techniques—Alloys were prepared and the transformation of the ? phase studied during interrupted-quench and quench-and-temper isothermal heat treatments by means of hardness measurements and X-ray diffraction and metallographic techniques. The isothermal transformation of the ? phase on quenching and tempering was investigated further employing dynamic-modulus measurements. Electrical resistivity and limited Hall coefficient measurements were also obtained as part of the study. Alloy Preparation and Heat Treatment— Alloys containing 15, 20, 22, 30, 40, 45, 50, 55, 60, and 70 wt pct U were prepared from as-reduced uranium and crystal-bar zirconium. The alloys were double arc melted by consumable-electrode are-melting techniques. The final ingots were forged and rolled at temperatures between 790" and 840oC to 1/4-in. rod and 1/8-in. sheet. Chemical analyses of the fabricated alloys were

Jan 1, 1961

By R. M. Howe, J. Spotts McDowell

Preparation and Use.—Magnesite is an important refractory in open-hearth, heating, and electric furnaces for steel-making and in many of those employed in the metallurgy of copper and lead. It is sold in the form of brick, finely ground "furnace magnesite" for bricklaying, and dead-burned grains for making and repairing furnace bottoms. The latter are a mixture of granules varying in size from pieces of about 5/8 in. (1.6 cm.) diameter to very fine but sandy particles. Dead-burned magnesite results from calcining the crude or lightly burned mineral at a temperaturc that will not merely drive off practically all the CO2, but will also cause sintering of the particles. During this process the pieces shrink considerably and become hard, dense, and inert to atmospheric moisture and CO2; under-burned material, on the other hand, will hydrate on exposure to the air. A small percentage of ferric oxide seems to be necessary for the production of a satisfactory sinter; from 4.5 to 8 per cent. in the dead-burned grains is considered the most desirable amount. Dolomite has been little used for brickmaking in the United States, but it is prepared for use in the granular condition calcined or "double-burned" and is the principal ingredient of several materials offered for sale under various trade names for refractory purposes. Dolomitic refractories are almost wholly confined to the open-hearth and electric furnaces, where they are used for fettling and as substitutes for magnesite. Much more magnesite and dolomite are used for basic open-hearth steel-making than for all other refractory purposes. The hearth of the furnace is usually built up of magnesite brick and dead-burned grain magnesite so laid that the brick base is protected by a working bottom of the granular material. The latter is sintered into place in layers 1/2 to 1 in: (1.25 to 2.5 cm.) thick to a total depth of 12 to 18 in. (30 to 45 cm.) at the center of the furnace. After each heat, burned dolomite is thrown against the banks as high as it will stick, and all holes in the bottom are Glled. At most plants such holes, at the end of each week, are also carefully filled with dead-burned grain magnesite. For temporary

Jan 1, 1920

By C. S. Barrett, O. R. Trautz

PREVIOUS investigations have shown that lithium is body-centered cubic from near its melting point to the temperature of liquid air1,2,3 Nevertheless there was an incentive to search again for a transformation at low temperatures: C. Zener4,5 has remarked that the low value of the elastic modulus (11 - C12)/2 of body-centered cubic metals and alloys implies a rapid increase in free energy with decreasing temperature, which would favor the occurrence of a transformation; also the shear movement to which this modulus applies is one that can transform a body-centered cubic structure into a slightly distorted face-centered cubic structure. It was confirmed that lithium does not transform spontaneously at liquid nitrogen temperature, but it was found that a transformation can be induced at this temperature by cold working the metal,6 and at slightly lower temperatures a different transformation occurs spontaneously. Transformations were also found in solid solutions of magnesium in lithium. THE NATURE OF THE TRANSFORMATIONS Before presenting a detailed treatment of the technique used and the specific data obtained, it would be well to give a brief survey of the general characteristics of the transformations. A new crystal structure begins to form spontaneously in a specimen when it is cooled below a critical temperature. In lithium the structure appears to be close-packed hexagonal; in the Li-Mg alloys most of the diffraction lines (but not all) are near those for hexagonal lithium. The transformation proceeds as the temperature is lowered and soon stops if the temperature is held constant or raised. The course of the transformation on cooling is indicated by the curve at the lower left of Fig I. This curve is drawn in stepped fashion because the transformation goes by discrete steps with audible clicks. Because of the similarity to the decomposition of austenite into martensite in steels, it seems appropriate to designate the beginning of the spontaneous transformation on cooling as the Ms point. On heating to room temperature after the low temperature treatment only the usual BCC structure is found. On heating, the low temperature modification begins to disappear at a temperature which will be designated as Ac. The transformation on heating is halted when the rise in temperature is halted. The temperature must be raised 40 to 50°C above Ac before the reversion is complete-an interval which is sensitive to the rate of heating and to the time of holding at temperatures above Ac. This behavior on heating thus has similarities also to the formation of martensite in the cooling of steels.

Jan 1, 1948

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957