Search Documents

By James E. Gingrich

The new Track Etch technique for uranium exploration has been utilized in several survey programs conducted during the last few years. The results from these programs have been very encouraging, and new uranium ore bodies have been discovered by using this new technique. The method is being used in several exploration programs in various locations around the world. This exploration technique utilizes small pieces of special radiation-sensitive plastic film to detect the presence of radon gas which is released by uranium ore bodies. Because of the selectivity and sensitivity of the technique, ore bodies not normally detected with other surface or airborne monitoring methods are found. Since no large equipment or special training of personnel is needed, the technique is easily used in field operations. The basis for the Track Etch method, its application in field exploration programs, and the results obtained to date in locating uranium ore bodies are discussed.

Jan 1, 1976

By Robert L. Wilson

Computation of reserve tonnages, stripping ratios, and grade of ore has long been a revolting aspect of the young mining engineer's job. Weeks at the desk calculator may turn into months before a single job is completed. Then many additional hours are necessary to check the calculations. During the last decade, computing machines have been widely publicized as instruments which will accomplish fantastic feats. Tales of their magical qualities have overshadowed their most basic characteristics-that of being a labor-saving device. Prior to a discussion of the electronic calculator's use on a mining problem, it may be well to point out that these machines are neither magic nor will they replace the judgment of an experienced engineer. In short, the "mighty morons," as the computors are sometimes called, are excellent labor savers but must be used correctly. They are not a substitute for thinking.

Jan 6, 1961

In 1975, the US produced 10 900 tons (12,000 st) of U3O8 from ores whose grade ranged from a low of 0.160% to a high of 0.196% U3O8. By the early 1980's if the current mining projects described here are allowed to go on stream, Australia will be able to produce at least 10 900 tons of U3O8 annually from ores whose grade ranges from a low of 0.150%to a high of 2.300%. As pointed out in the previous article, this initial rate of production could have been reached now-giving an immense boost to the depressed Australian economy. So, let's have a close look at current mining projects.

Jan 1, 1977

The war story of the engineer corps at home and in France is told officially for the first time in the advance sheets of the War Department's brief history of American war efforts. Many of these accomplishments have been published before as isolated incidents, but they gave no idea of the extraordinary duties modern warfare has laid upon engineering troops. In the engineering units that reached the other side, there were seven regiments and two battalions of railway construction engineers; five battalions for maintenance of way; two battalions for maintenance of railway equipment; four regiments and one battalion to operate the main American railways in France; three regiments to operate light railways and their repair shops; two regiments to operate the regular railway repair shops; two regiments and six separate battalions on general construction work; two regiments for storing and transporting engineer supplies; a forestry regiment; a light-railway construction regiment; a roadbuilding regiment; a water-supply regiment; a mining regiment; a quarrying regiment; a technical regiment for surveying and sound ranging; three survey and printing battalions; two railway transportation battalions; an electrical and mechanical regiment; several separate companies to operate cranes; a camouflage service; five inland waterway companies, to operate canal boats and the like; five pontoon trains and a pontoon

Jan 6, 1919

By John C. Smock

While I was engaged in the preparation of a catalogue or list of mineral localities of the United States, east of the one hundredth meridian, for the U. S. Geological Survey, the thought occurred to me that an arrangement or classification of the iron-ore districts of the eastern part of our country according to their geological horizons would be an interesting topic for a paper, and would furnish a basis upon which to arrange many facts brought out by the constant development of our iron-mining districts. Our text-books of mineralogy, geology, and ore-deposits describe the iron-ores and the

Jan 1, 1884

By John A. Church

AT a time when the treatment of gold and silver ore9 by fusion, in opposition to the mill-process, is attracting so much attention in this country, it may be useful to consider what is done in a well-conducted foreign work. For this purpose I will ask the reader to accompany me to Lend, in Austria, a small but thoroughly organized

By R. H. Barham, G. W. Nabor

Linear aquifers, either limited or essentially infinite, may be encountered in reservoir engineering practice. In areas where faulting fixes reservoir boundaries, the fault block reservoir may have an aquifer of limited extent whose geometry is best approximated as linear. An infinite linear aquifer can occur as a regional feature whenever water movement through the aquifer member is constrained to one direction. Such constraints can arise from major faults, facies changes or pinchout of the member. Miller* pointed out that linear aquifers have received only meager attention in the past. He analyzed the performance of finite and infinite aquifers, developed working equations and curves, and presented examples. While Miller's curves may be used fairly easily, a separate one is required for each size of aquifer. In this paper, Miller's equations have been used as a starting point. By modifying them slightly, they can be reduced to a form which yields a single working curve, applicable to any size of aquifer. Thus. interpolation between curves is eliminated and accuracy is improved. Miller's results for finite aquifers covered only the boundary condition of no flow across the outer aquifer boundary. This paper also includes the case of constant pressure at the outer aquifer boundary.

Jan 1, 1965

By William B. Plank

THERE are 19 pct fewer undergraduate and graduate mineral engineering students enrolled in the ECPD accredited schools of the United States this year than there were a year ago. The figures are: 8727 this year and 10,674 last year. The entire engineering group in both countries numbers 171,070, as compared with 184,547 last year and 252,250 in 1947-48, the peak year. This is a decrease of 7.3 pct since last year, less than half as much as the decrease in the mineral engineering group. These figures on engineering enrollment for the current year, 195.1-52, in colleges of the United States and Canada were prepared jointly by the U. S. Office of Education and the American Society for Engineering Education. The seriousness of the situation is shown. by the reported demand for 60,000 to 90,000 engineers this year for civilian and defense industries and only 35,800 will graduate next June. Many of the 1952 graduates are subject to Selective Service, having been granted deferments while in college, and ac- [ ]

Jan 1, 1952

By Thomas Egleston

The adoption of the regenerative principle for burning fire-bricks, pottery, etc., has been delayed beyond what would naturally have been expected, because there bas been until recently little necessity for high heat in burning such material. But the introduction of pro-

Jan 1, 1887

By Harold E. Thomas, Samuel S. M. Chan, Nicholas Bada

The U.S. Bureau of Mines has developed a technique for locating and evaluating bedding plane cracks in mine roof by an air-injection and hot-film flow logging technique. It is ultrasensitive to cracks and is especially useful for detecting the early stage of crack development. Potential applications include: (1) correlation with roof sag measurements, (2) locating cracks for grouting, (3) comparison of mechanical and resin roof bolt effectiveness, and (4) possible delineation of the fracture zone to confirm the arch hypothesis. The required equipment is inexpensive and simple to operate.

Jan 1, 1975

By W. F. Baldwin

The timing circuit generally employed in Carter Reservoir Behavior Analyzers consists of a synchronous motor driven cam which actuates a microswitch. A mechanically actuated timer of this type has several inherent disadvantages, among which are the following: 1. The first time interval may not be of uniform length, depending on the exact position of the cam at the conclusion of a previous run. 2. The positioning adjustments on the microswitch lever arms are critical and require periodic readjustment. 3. The mechanical system is subject to wear which will ultimately impair its accuracy. It was therefore considered desirable to devise an alternate method which would eliminate these difficulties without introducing others that would be equally troublesome. This note describes the design of an electronic timing device which has been incorporated in the analyzer constructed by the Field Research Laboratories of Magnolia Petroleum Co. The electronic timer circuit is built around a simple neon glow tube relaxation oscillator, the complete circuit diagram of which is shown in Fig. l. The operation of the circuit is as follows: Condenser C, is charged to the critical firing voltage of the neon glow tube VR-75 by battery B1 through resistors R1 and R2. When the neon glow tube fires, the condenser C, is discharged, The charging cycle then repeats itself,

Jan 1, 1950

By Desmond De Villiers Oxford, Peter H. Williams

Nchanga Consolidated Copper Mines, Ltd., is one of the four mines operated by the Anglo American Corp. in Northern Rhodesia, now the independent nation of Zambia. Today Nchanga is the second largest single producer of copper in the world, accounting for more than 200,000 long tons of copper annually at a monthly milling rate of 430,000 tons of ore. The average mill-head grade is about 5.20% total copper, of which approximately 60% is copper sulfide. The remainder, referred to as "acid soluble," is copper oxide. Nchanga mines three separate orebodies varying in grade and sulfide-to-oxide ratio. Ore is processed in two separate grinding circuits feeding into three separate flotation circuits. A fourth flotation circuit treats leach plant residue for additional recovery of sulfides.

Jan 1, 1965

By John J. Reed

The mines of southeast Missouri's Lead Belt have been in operation since 1864, almost 100 years. During this period about 10 pct of the total ore available has been left in place as pillars, and this now represents the best ore reserve left to the older mines. St. Joseph Lead Co. has been investigating various plans of pillar recovery for several years. The example to be described is only one possible approach under a specific set of conditions. Conditions vary greatly in the different areas within the Lead Belt, and the same approach would be entirely in- adequate in certain other areas, but there are important sections where this system is clearly applicable.

Jan 7, 1959

By James K. Greenlee, David W. Wisecarver

It is estimated conservatively that some 14 billion tonnes of coal reserves in the United States exist in beds considered steeply dipping, i.e. at pitches or slopes in excess of 15O - a slope too steep for practical use of mobile wheel or crawler drive mining equipment. Past attempts to mine these steep reserves are limited owing to production difficulties and high costs, an expected result when mining of slopes must be done conventionally and mining on strike with mobile mining equipment is restricted because of limited cross sectional opening and operating room. In Europe, these adverse conditions are countered through the use of the longwall mining method. In fact, longwall mining is employed along pitches up to 55°. However, both operating and administrative - conditions in foreign steep seam coal mines differ from ours in that (1) the mine does not necessarily have to make a profit and (2) single entry development of retreat mining panels is acceptable practice. In the United States development can be done with a minimum of two entries only, provided belt haulage is not used during development.

Jan 1, 1981

By O. C. Wheeler

There was an increased amount of activity in the oil business in Colombia during 1934 over that of the past several years in point of production, development and exploration. The Tropical Oil Co. continued to be the only company operating on what may be called a commercial basis, although the Gulf, through its subsidiary, the Colombian Petroleum Co., was actively engaged in exploratory and developmental work on its Barco property in eastern Colombia. The Socony Vacuum interests acquired an option from Sr. Luciano Restrepo on a concession in Las Monas-Sogamoso River area and carried out geological investigations on these lands during the year. Colombian Petroleum Company The activities of the Gulf in exploration and development in Colombia during 1934 were confined to the Barco concession. The following information is furnished through the kindness of Mr. E. S. Bleecker, Chief Geologist of the South America Gulf Company. Two strings of tools were kept in operation throughout the year on the Petrolca (Tarra) structure. Three wells were completed, including one deep test, all of which were producers from one or more of the three zones which have been defined in the Lower Cretaccous limestone formation. On the Rio de Oro structure, some 45 miles northwest of Petrolea, a complete camp has been established on the Catatumbo River, about

Jan 1, 1935

By AIME AIME

FOR the following notes and pictures we are indebted to Sumner S. Smith of Oakland, California: Gold was discovered on Squaw Creek in the fall of 1927 by an Indian named "Paddy Duncan," and most of the stream was staked by natives. This stream is about 12 miles in length and flows into the east fork of the Alsek River, 10 to 15 miles below the old Dalton Post in British Columbia, near the international bound-

Jan 1, 1929

By Hallan Marsh

THE subject of this paper is apt to bring to mind wells ranging from 6000 to over 8000 ft. in depth. However, it is uncommon to pump wells at depths greater than about 5000 ft. Fig. 1 shows the number of wells being pumped at various depths by one company in Southern California. FIG. 1.-NUMBER OF WELLS BEING PUMPED BY ONE COMPANY FROM VARIOUS DEPTHS IN SOUTHERN CALIFORNIA. A few companies have a very few wells pumping at depths greater than this. This paper will deal with wells between 3000 and 5500 ft. in depth. Most California oils at these depths are between 25° and 35 gravity. The subject is so broad that it will be necessary to omit many interesting phases, and to treat others very briefly. Power, power transmission equipment, power efficiency, counterbalancing, sucker rods, pumps and volumetric efficiency will be discussed.

Jan 1, 1928

By Colin Fink

TANTALUM and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTa206), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore, becoming (Fe, Mn)O.(Ta, Cb)205. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and silica.1

Jan 1, 1931

By Richard H. Sprute, Dennis J. Kelsh

Slow-settling, fine-grained suspensions can often be dewatered and densified by applying direct current between buried electrodes. Although water removal rates and power expenditures depend on physical and chemical properties of the treated slurries, metal mine tailings from Idaho, Colorado, and Mexico have responded well in laboratory testing, as have 29 samples of ultrafine coal waste from mines in nine states. This Bureau of Mines report reviews field tests at two Idaho metal mines and describes the recent installation at the Henderson molybdenum mine near Empire, Colorado, and the treatment of coal sludge at a Clinchfield Coal Co. preparation plant near Dante, Virginia.

Jan 1, 1980

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, which lay about 1100 ft to the south. This vein system has been explored and mined over 9000 ft horizontally and 4800 ft vertically. In 1950 continued exploration led to the discovery and development of replacement orebodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma mine and follow the strike and the 30º east dip of the host limestone. Strike length of the ore bodies varies from 250- 500 ft and thickness from 15-125 ft. The orebodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is characteristic of portions of the replacement beds. In many instances the ore is blocky, badly fractured and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 6, 1973