Search Documents

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of SO2 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 3/4 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no SO2 could be detected in the gases. In all cases the depth of bed was 4 1/2 in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which SO2 determinations were made could not be measured, but has been calculated from the SO2 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on SO2 concentration in sintering under ordinary conditions show a high SO2 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum SO2 concentration is obtained 2 ½ min. after

Jan 1, 1942

By R. I. Jaffee, J. W. Roberts, D. N. Williams

DISPERSION hardening as an alloying process has aroused increasing interest in the past few years. This alloying procedure, in which an insoluble phase is dispersed randomly through a metal or alloy, is believed to be especially suited for the attainment of creep strength at elevated temperatures since the dispersed phase is metallurgically stable. Another advantage is that the physical properties of the matrix phase, such as electrical conductivity, remain relatively unaffected by alloying. These two characteristics resulted in interest in the applicability of dispersion hardening to copper and copper alloys. A study of copper alloys prepared by powder metallurgy methods has shown some strengthening from oxide dispersions.' However, powder metallurgy processing would not be economical for large scale production of dispersion hardened copper-base alloys. Therefore, the research described in this article was initiated to examine methods of forming dispersion alloys which would not require powder metallurgy processing. If powder metallurgy processing is to be avoided, a method must be found by which the dispersion material can be introduced into and dispersed through the melt before casting. When the dispersed phase is an oxide or similar nonmetallic, it is extremely difficult to form a satisfactory liquid: solid dispersion since successful mixing requires that the melt wet the dispersed phase. It is almost impossible to force a nonwetted particle beneath the melt surface. This difficulty can be avoided, however, if the oxide particles are produced in molten copper by reaction within the melt. The problem would then reduce to maintaining randomness until solidification. Four procedures were considered for producing an oxide particle within molten copper by reaction. In all cases, the intent was to react oxygen (0) with a reactive metal (X) to form an oxide (XO) within the copper melt. These reactions were as follows: 1) (Cu-X), + (O)g (Cu)1 + (XO)S [1] 2) (Cu-X)1 + (Cu2O)s (Cu)x + (XO)S [2] 3) (Cu-OK)1 + (Cu-X)1 (Cu)1+(XO)9 [3] 4) (Cu-OK)1 +(X)s (Cu)1 +(XO)s [4] The reactions were carried out in an 8-lb melt of 99.98 pct Cu maintained in the vicinity of 2200oF by induction heating. Where possible the amount of the reactants was controlled to give 1 to 5 vol pct oxide. Mechanical stirring during the reaction period was used to minimize agglomeration of the reaction product. The presence of a reaction product was determined metallographically by study of an ingot cast from the melt at the end of the reaction period. Reaction [I] was studied by dissolving aluminum in the melt followed by forcing oxygen through the melt. The melts became quite sluggish during the reaction period suggesting that A12O3 was formed. However, the reaction product rose out of the melt rapidly, possibly due to the flushing action of the oxygen stream, and little dispersed phase was formed. Reaction [2] was examined by dissolving aluminum, silicon, or nickel i; the melt and then adding Cu20 (melting point 2250F). This procedure was unsuccessful. Although Cu2O was easily stirred into cop-

Jan 1, 1961

By Iley B. Browning, Louise Barton Freeman, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

• Pellets of concentrated iron ore have been smelted in the blast furnace by Armco and the results proved satisfactory. Various percentages of pellet burdens were tried and it has been found that charges up to 70 pct pellets are workable. •In the reorganization of the Department of the Interior, two new assistant secretaries were appointed and the work divided between the four assistant secretaries. C. Girard Davidson will head a division of mineral resources including the Bureau of Mines, Geological Survey, Division of Oil and Gas and Division of Geography. •Germanium, one of the rarest of metals and a wartime strategic material, has been discovered almost in the shadow of the Capitol. The only catch is that the scattered nature of the deposits makes profitable recovery extremely doubtful. Nevertheless, experts have tabbed the concentration in the District of Columbia area the world's second richest known concentration of the element. • Cakes of mica, weighing up to 500 lb, have been formed at the Colorado School of Mines by a new "cool hearth" method. The process avoids use of crucibles and contains the molten mica in a basin of unmelted raw mixture from which the melt was derived. Crystallization takes place in this melting basin which forms a center pool surrounded by a solid cool mass of the unmelted raw mixture. • William 1. Baxter, of the International Economic Research Bureau, predicts a period of deflation because of war-essential restrictions on consumer credit and materials use. He stated; "the recent prosperity was based mainly on the sales boom in autos, homes, and household accessories." •Two subsidiaries of United States Steel have decided to build four new ships immediately to augment iron ore and limestone carrying capacity on the Great Lakes to meet demands created by the national defense emergency. •The Norfolk and Western Railway is making a complete change over to coal to drive its locomotives. •A national roster of scientific personnel similar to the one used in the last war will be established by the Office of Education, by agreement with the National Security Resources Board. The new unit, the National Scientific Register Project, will make studies of the Nation's scientific manpower supply and recommend steps to increase the numbers of skilled personnel where needed. •National Lead Co. will start construction immediately of new facilities at St. Louis, Mo., for production of titanium pigments for paints. Producers of titanium pigments have been under considerable pressure to meet all demands from paint manufacturers, particularly for titanium dioxide. •The basic criteria for deferment of reservists in civilian occupations are (1) the Department of Labor List of Critical Occupations, and (2) the Department of Commerce List of Essential Activities, both of which were announced Aug. 3. Fundamentally, the reservist deferred must be engaged in a critical occupation which is necessary to a highly essential activity, and he will be deferred only until he can be satisfactorily replaced in that occupation. A delay in call to active duty, it was emphasized, may not be considered as an indefinite exemption from military service.

Jan 9, 1950

By R. V. Riley

IN the metallographic examination of the alloys of iron and silicon, several investigators1-' have reported on the occurrence of an unusual type of etched structure, particularly in the alloys of higher silicon content. This, the so-called "barley shell" structure, has been observed with iron-silicon alloys over a wide range of silicon content, and under certain circumstances it can be seen upon the micro-sections of pure iron. The barley shell structure may be demonstrated most easily with iron-silicon alloys in the range 8 to 20 pct Si after etching in a hydrofluoric acid base etchant. Two etchants which produce the structure are: Corson's reagent, which is 2 parts hydrofluoric acid, 1 part nitric acid, and 2 parts glycerol; and picric acid reagent, which is 1 part hydrofluoric acid and 1 part saturated solution of picric acid in alcohol. Both when freshly prepared and used for etching commercial silicon-iron alloys containing 14 to 16 pct Si, invariably produce the barley shell structure shown in Fig. la. It is now well known that the barley shell structure is a pseudomorph and the true structure of an alloy of this composition consists of a single phase of silico-ferrite together with graphite as shown in Fig. lb. Lower silicon alloys and even pure electrolytic iron may also be etched in the above reagents to give the barley shell provided the etchant has been either: 1—Stored in contact with glass or silica, or 2—used previously for etching an iron containing silicon. Pure iron etched in perfectly pure hydrofluoric acid base etchants free from silicon contamination gives a normal structure free from the barley shells. Therefore, although the hydrofluoric acid in the reagent primarily is responsible for the barley shells, silicon, or its compounds, also must be present, either in the etching reagent or in the specimen. It was of considerable interest to the author to read the paper by Wachtell,? in which the barley shell etch was deliberately used for the identification of the boundaries of high and low silicon areas in diffusion experiments made upon laminate bars of compacted and sintered pure iron and ferrosili-con powders. This method of utilizing the barley shell etch is novel and in the hands of the investigator gave a useful differentiation between the high and low silicon areas in those specimens. For the reasons already given, however, the technique is not to be regarded as of universal application. Misleading results might be obtained, for example, if two or more specimens were etched in the same etchant. Fresh pure reagents only must be used each time. Provided this is done and the investigators are well aware of the limitations of the method, then the barley shell pseudomorph can be made of limited use in distinguishing between higher and lower silicon areas in a microspecimen of a ferrous material. The greatest of care must be exercised in the interpretation of the results which may be regarded as qualitative only and may, in fact, not be specific to silicon alloys.

Jan 1, 1952

By E. P. McCurdy, W. J. Tait, A. E. Craig

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

By Reed W. Hyde

SOME information has been published on the sulphur dioxide concentration of gases from Dwight-Lloyd machines sintering lead ores but most of this relates to the customary practice in which the charge is relatively high in lead and is sintered in two passes over the machine. It is thought, therefore, that the following observations on sintering in one pass a low-lead, low-sulphur charge may be of interest. The data were obtained in sintering lead sulphide flotation concentrates mixed with minus 20-mesh oxide ore, the mixture carrying 16.8 per cent Pb and 5.3 per cent S. No returns were used because of the limited amount of sulphur available as fuel, but the mixture pelletized readily to make a satisfactorily permeable bed on the sintering machine. As there was a possibility that the SO2 might be utilized, a series of runs was made to determine the concentration of S02 in the gases at different points along the wind box, and the effect on this concentration of changes in the wind-box vacuum. Several runs each were made with vacuums (as measured in inches of water at the wind box) of (1) 2 to 1 1/3 in., (2) 4 to 3 1/2 in. and (3) 6 to 5 1/8 in. The averages of the determinations from each series are platted on the graph (Fig. I). The vertical scale shows the percentage by volume of SO2 (as determined by the Reich method), and the horizontal scale shows the time expressed as percentage of the total sintering time. Sintering was considered to be complete when no S02 could be detected in the gases. In all cases the depth of bed was 4 ½ in. and the weight of dry charge per square foot of hearth area was 45.2 lb. Other data are given in the table. The volume of gases corresponding to the several points along the wind box at which S02 determinations were made could not be measured, but has been calculated from the S02 content and sulphur elimination on the assumption that the volume is uniform throughout the sintering period. This is not strictly true, as with a given vacuum the volume will usually drop slightly toward the middle of the period and increase toward the end. However, this assumption is a reasonable approximation. Several interesting features are brought out by these data. In general, the published data on S02 concentration in sintering under ordinary conditions show a high S02 concentration in the early stages followed by a rapid decrease in concentration and with relatively little SO2 in the gases from the last half or third of the operation. In other words, the greater part of the sulphur elimination is obtained in the first third or half of the period. In these runs, the 6-in. vacuum, which approximates the usual operating condition, gives a curve that follows this customary pattern. Maximum S02 concentration is obtained 2 ½ min. after

Jan 1, 1942

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

By John T. Galey

The outstanding developments of the year in southwestern Pennsylvania were the establishment of the Summit Fayette County gas pool and the gas pool in Nicholson township, Fayette County, and Monongahela township, Greene County, as major producing areas, and the indication of four new shallow gas pools. Curtailment of drilling for shallow gas is expected to follow order M68 of the Office of Production Management. Gas completions were approximately 70 per cent higher, oil completions nearly 25 per cent lower, dry holes were unchanged and drilling wells as of Dec. 31, 1941, nearly loo per cent higher than last year. Shallow Development Oil.—Outside Butler County, only 11 producers were drilled, with a total initial of 221 bbl. The best of these was in a portion of Gilmore township, Greene County, which ordinarily produces gas. This well flowed 77 bbl. in 11 hr., along with about one million cubic feet of gas from the Fourth (U.Dev.) sand. Washington County had a 10.20 and a 25-bbl. well in Morris township and a 20-bbl. well in South Franklin township. These were all in the Fifth Sand. The price of oil to Jan. 27 was $1.80 per barrel, when a 15¢ increase was made. This was followed by a raise of 20¢ on Apr. 23, 15¢ on May 21, 20¢ on June 18 and 25¢ on Aug. 14. The last increase was canceled on Aug. 23 by the Office of Price Administration, which pegged southwestern Pennsylvania crude at $2.40 per barrel. Gas.—An almost doubled initial production of natural gas is the result of the large increase in number of wells drilled. The outstanding discovery of the year was in the vicinity of Armbrust, Hempfield township, Westmoreland County, where a well drilled to what at first was considered the Bayard sand, but what is now known to be the Fifth (U.Dev.) sand, at 2100 ft. found nearly 5 million cu. ft. of gas. Since this completion 14 wells have been finished, only one of which was dry, giving a combined total open flow of approximately 15 million cu. ft. The sand is 35 to 40 ft. thick and the saturation extends through most of that thickness. Rock pressure, which is 1040 lb. per sq. in., is abnormally high. An area of only about one square mile has been proven but some of the 24 new wells drilling as of Dec. 31 will no doubt extend it considerably. This development has taken place in an area heretofore considered to have had little prospect. There were three good wells in other parts of Westmoreland County. One well in Franklin township, which had 12 million cu. ft, of gas in the Fifth sand, was entirely surrounded by dry holes but is still pro- . ducing at a high rate. In Bell township a 1.6 million cu. ft. well was found in the Speechley (U.Dev.) sand and in Washington township the same sand produced 2.7 million cu. ft. with shut-in pressure of 970 Ib. at 2820 ft. This well is offset by two dry holes and one well with a capacity of only 10 M cubic feet.

Jan 1, 1942

By John T. Galey

The outstanding developments of the year in southwestern Pennsylvania were the establishment of the Summit Fayette County gas pool and the gas pool in Nicholson township, Fayette County, and Monongahela township, Greene County, as major producing areas, and the indication of four new shallow gas pools. Curtailment of drilling for shallow gas is expected to follow order M68 of the Office of Production Management. Gas completions were approximately 70 per cent higher, oil completions nearly 25 per cent lower, dry holes were unchanged and drilling wells as of Dec. 31, 1941, nearly loo per cent higher than last year. Shallow Development Oil.—Outside Butler County, only 11 producers were drilled, with a total initial of 221 bbl. The best of these was in a portion of Gilmore township, Greene County, which ordinarily produces gas. This well flowed 77 bbl. in 11 hr., along with about one million cubic feet of gas from the Fourth (U.Dev.) sand. Washington County had a 10.20 and a 25-bbl. well in Morris township and a 20-bbl. well in South Franklin township. These were all in the Fifth Sand. The price of oil to Jan. 27 was $1.80 per barrel, when a 15¢ increase was made. This was followed by a raise of 20¢ on Apr. 23, 15¢ on May 21, 20¢ on June 18 and 25¢ on Aug. 14. The last increase was canceled on Aug. 23 by the Office of Price Administration, which pegged southwestern Pennsylvania crude at $2.40 per barrel. Gas.—An almost doubled initial production of natural gas is the result of the large increase in number of wells drilled. The outstanding discovery of the year was in the vicinity of Armbrust, Hempfield township, Westmoreland County, where a well drilled to what at first was considered the Bayard sand, but what is now known to be the Fifth (U.Dev.) sand, at 2100 ft. found nearly 5 million cu. ft. of gas. Since this completion 14 wells have been finished, only one of which was dry, giving a combined total open flow of approximately 15 million cu. ft. The sand is 35 to 40 ft. thick and the saturation extends through most of that thickness. Rock pressure, which is 1040 lb. per sq. in., is abnormally high. An area of only about one square mile has been proven but some of the 24 new wells drilling as of Dec. 31 will no doubt extend it considerably. This development has taken place in an area heretofore considered to have had little prospect. There were three good wells in other parts of Westmoreland County. One well in Franklin township, which had 12 million cu. ft, of gas in the Fifth sand, was entirely surrounded by dry holes but is still pro- . ducing at a high rate. In Bell township a 1.6 million cu. ft. well was found in the Speechley (U.Dev.) sand and in Washington township the same sand produced 2.7 million cu. ft. with shut-in pressure of 970 Ib. at 2820 ft. This well is offset by two dry holes and one well with a capacity of only 10 M cubic feet.

Jan 1, 1942

By H. J. Beach, W. C. Goins

The laboratory development and field use of oil well cement compositions* with high resistance to drilling mud contamination are described. Resistance is obtained by adding a I-lb mixture composed of three parts paraformaldehyde to two parts sodium chromate tetra-hydrate for each sack of cement. This mixture neutralizes the cement-retarding properties of quebracho and other tannins, starch, sodium carboxymethylcellu-lose, Ignite, and monovalent salts of lignosulfonic acid. The retarding properties of calcium lignosulfonate are unaffected. The decontaminating mixture may be used in common cement (designated Type I by ASTM specifica-tions,' Class A by API Std. 10A2) or in a slow set slurry prepared from common cement by addition of calcium lignosulfonate. No changes in slurry viscosities or thickening times are caused by the protecting reagents. The method has been used in 185 field jobs where an improved success ratio has been obtained in plug setting. INTRODUCTION Field experience and laboratory investigations have established contamination by drilling mud as a major factor in oil well cement failures. During 1955, 12 attempts were required to set six open-hole cement plugs in the Timbalier Bay field, La. Eighteen to 30 hours elapsed between placing and testing the plugs in preparation for sidetracking operations. Considerations of rig time expense required immediate resetting where soft cement was drilled after a reasonable waiting period. Sea water drilling mud was used in each well and daily additions of thinners, usually lignites, had been required. Sodium carboxymethylcellulose had been added regularly to control fluid loss. The 50 per cent plug failures were attributed primarily to contamination by the mud. Similar experiences can be found in other fields along the Texas and Louisiana coasts where drilling muds normally contain large quantities of organic treating materials. Cement contamination was the subject of a survey by the Mid-Continent District Study Committee on Cementing Practices and Testing of Oil-Well Cements of the API.3 Data collected from member laboratories and released in Sept., 1951, reported the effects of a number of drilling mud treating chemicals on cement. The study revealed that many of the additives, notably the organic materials in relatively small quantities, had marked effects on the properties of cements tested. Severe losses in strength and erratic thickening time resulted from small additions of mud treating chemicals such as quebracho, starch, sodium carboxymethylcellulose, and lignite. The report included no recommendations of methods for overcoming the problem. One investigation of the contamination problem reported the successful use of activated charcoal in setting cement plugs after conventional slurries had failed.4,5 The investigation indicated that an optimum concentration of 5 per cent activated charcoal was effective in combating contamination from 16.7 volume per cent of treated mud. Laboratory and field muds were included in tests and contained varied quantities of ode or more of the following: quebracho, caustic, starch, lime, and calcium lignosulfonate. The function of the charcoal appears to be physical, removing the organic materials by adsorption. The method may be employed in API Class A or Class D (unretarded slow set) cements. The chemical approach presented here is based on

Jan 1, 1958

By D. J. Blickwede

PRESENT knowledge of the effects of time and temperature upon stabilization of the austenite-martensite reaction in steel is fairly complete,1-3 but at the time the work described herein was initiated there was no information about the effects of alloy elements on the phenomenon. However, it has been assumed on theoretical grounds that alloy elements, particularly carbide formers, may have a significant effect on stabilization.' The present work was undertaken to provide information about the effect of two common elements, nickel and molybdenum, on stabilization in hypereutectoid and hypoeutectoid steels. Seven induction-furnace melted, 1.2 pct C steels ' with a variation of nickel from 0 to 6 pct and of molybdenum from 0 to 1.0 pct were used for most of the experiments. Along with these a series of 0.4 pct C steels containing 0 to 6 pct Ni were also studied. The chemical compositions of the steels are listed in Table I. Stabilization in these forged, hot-rolled, annealed, and centerless ground steels was measured by aging brine-quenched specimens (aus-tenite temperature, 1800°F) at 95" and 150°F and then determining the change in specific volume produced by subsequent cooling from room temperature to —320°F.³ In presenting the results the decrease in the change in specific volume, ?V, after various stabilization times is used. This is given by ?V -= ?VO - ?V1 where AVO is the change in specific volume on quenching directly to —320°F and aV, is the change in specific volume on quenching to —320°F after stabilizing for time t. In other words, ?V is a direct measure of the amount of martensite that is lost to the subzero quench as a result of stabilization and hence is greater, the longer the aging time or the higher the aging temperature. The results are shown in Fig. 1. The scatter of the data, which are not shown for clarity and brevity, was sufficient to make the relative location of the curves on the ?V axis inaccurate within ±2x10-5 cc per g. However, some generalities appear which are of interest. Effect of Nickel In the 0.4 pct C steels, up to 3 pct Ni has little, if any, effect on the rate or amount of austenite stabilized at 95°F, Fig. la. Increasing nickel from 3 to 6 pct almost doubles the amount of austenite stabilized in a given time. In the 1.2 pct C steels aged at 95°F, increasing the nickel from 1 to 3 pct appears to decrease the amount of stabilization, and a further increase to 6 pct Ni completely eliminates stabilization as shown in Fig. lb (M, of 6 pct Ni steel was below room temperature). The same behavior was exhibited by these steels stabilized at 1500°F, especially after aging for periods longer than 5 hr, Fig. lc. Thus it appears that up to 1 pct Ni has little effect on stabilization at low or high carbon levels. More than 1 pct Ni increases stabilization at low carbon contents and decreases it at high carbon contents. Ward, Jepson, and Rait5 have found that at inter-

Jan 1, 1954

By F. W. C. Boswell, R. L. Cunningham, H. M. Weld

Chemical analysis shows the partition of the magnesium addition between the metal and the graphite is independent of whether the graphite is in the form of nodules or flakes. The bright central spot observed in nodular graphite polished sections is shown to be due to the structure of the nodules. DURING the past few years numerous papers have been published on the production1-7 and heat treatment" of nodular cast irons. However, very little information is available on the structure of the nodules and the reason for their formation. It would appear that an explanation of the phenomenon of nodulation must await a detailed knowledge of the nature of the nodule. Disagreement exists among various workers on such a fundamental point as to whether or not a nodule actually contains a microscopically visible, nongraphitic nucleus.9-11 Work was initiated with a view to obtaining definite information on this and other aspects of the problem. Chemical Separation and Analysis Microscopic appearance had indicated9-11 that a nongraphitic core might exist in nodules (Fig. 1). It appeared that a chemical comparison of separated nodules and flake graphite would be profitable, for if the core is nongraphitic a relatively large amount of certain elements would be found in the nodules as compared to the flake. This comparison could best be made by obtaining nodules and flake from the same melt of cast iron, part of which had been in-noculated with a suitable addition reagent for the formation of nodules. A 300 lb melt was produced. About half of this was innoculated in the ladle with an Fe-Si-Mg alloy to produce nodules and cast into keel blocks; the remaining half of the melt had silicon added in an effort to compensate for the silicon in the innoculant used in the other half of the melt and this was cast into similar keel blocks. The analyses of the resultant irons are given in Table I. Nodules and flake were chemically extracted from 2 kg samples of metal as described in the appendix. While this method dissolved the iron and chromium carbides, it did not dissolve the titanium, vanadium, and molybdenum carbides. These latter carbides could have been removed by nitric acid, but in other experiments it was found that it attacked pools of metallic iron entrapped in the nodules which had, until the nitric acid treatment, been protected from the attack of the sulphuric, hydrochloric, and hydrofluoric acids. It will be shown in the next section that entrapped iron exists in nodules but not in flake. On microscopic examination many tiny irregular particles were observed to accompany both the nodules and the flake. These were identified by tabling a sample of nodules from which a sufficient fraction was obtained for X-ray analysis. A good pattern of titanium carbide was obtained indicating that this was the predominant compound present. Since it was not possible to determine how completely the carbides could be removed mechanically and since their removal from flake is much more difficult, it was decided not to resort to any separation as this would render further comparisons more difficult. The samples were ashed in a combustion

Jan 1, 1953

By G. R. Gray, T. S. Chapman, J. L. Foster

THE wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as tragacanth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. INTRODUCTION It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.1-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-11 The wall-building properties of fresh-water muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods generally used in controlling filtration of fresh-water muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. LABORATORY INVESTIGATIONS Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester' at a pressure of 10o lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 c.c. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1941

By J. W. Halley

THE effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. PUBLISHED WORK A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimm1 found no change in Olsen ductility, Rockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.15 per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.01 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.06 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0.50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. EXPERIMENTAL WORK Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1942

By J. W. Halley

THE effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. PUBLISHED WORK A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimm1 found no change in Olsen ductility, Rockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.15 per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength 0f from 100 t0 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0.50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. EXPERIMENTAL WORK Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1942

By J. L. Foster, G. R. Gray, T. S. Chapman

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942

By J.W. Halley

The effects of tin on steel have become increasingly important because of the necessity of using poorly detinned scrap, tin cans, and terne plate, in the open hearth. Since a tin can contains about 1.5 per cent tin, it would be possible to have up to 0.75 per cent tin in steel made with a 50 per cent scrap charge. In order to use tin-containing scrap, it is necessary to know the effect of tin on various grades of steel. The following investigation is by no means comprehensive but covers a number of steels in which tin content is important. Published Work A number of investigations of the effects of tin on rolling quality and physical properties have been published. It has been found that tin increases strength and hardness and reduces ductility and notched impact resistance. The decrease' in ductility and notched impact resistance becomes more marked as the carbon decreases. McKimml found no change in Olsen ductility, Kockwell hardness, yield strength, tensile strength or elongation in cold-reduced strip containing up to 0.124 per cent tin. A tin content of 0.1j per cent gave difficulties in rolling and increased the hardness but 0.21 per cent tin showed no change in properties from material containing very little tin. No explanation of this contradiction is offered. Andrew and Peile2 investigated steels containing 0.10 to 0.25 per cent carbon and up to 0.63 per cent tin. They found an increase in tensile strength of from 100 to 200 lb. per sq. in. for each 0.01 per cent tin on normalized samples. The elongation and reduction of area were decreased and the notched impact resistance was reduced markedly. Quenched and drawn samples did not show embrittling if water-quenched from the draw temperature of 1148°F. (620°C.). They could find no evidence of tin under the microscope. Whitely and Braithwaite3 investigated the effect of tin on rail steel containing 0.55 to 0.60 per cent carbon. They found that 0.08 per cent tin caused a marked decrease in elongation, notched impact resistance and the degree of bend. The tensile strength was increased in some tests and not in others. Bolsover and Barraclough4 investigated the effect of tin up to 0. 50 per cent on a 0.35 per cent carbon steel and on several alloy steels with from 0.30 to 0.40 per cent carbon. They found a comparatively uniform decrease in notched impact resistance with increasing tin on quenched and drawn samples. If the samples were quenched from the drawing temperature or reheated to the drawing temperature and quenched, the embrittling was much less severe. Steels containing molybdenum suffered much less embrittlement than other steels. Experimental WoRk Effect of Tin on Low-carbon Rimmed Steel Increasing quantities of tin were added to four ingots of a heat of the following ladle analysis: carbon, 0.08 per cent; manganese, 0.39; phosphorus, 0.009; sulphur, 0.025.

Jan 1, 1943

By B. M. Larsen, T. E. Brower

Introduction and Summary By "thermochemical factors" we refer to those variables which affect the net heat which must be put into the bath in order to make a heat of steel from any given set of charge materials. This is admittedly only one phase of the production rate problem. The whole problem includes also consideration of rate of charging, flame radiation intensity, rate of optimum fuel input obtainable without undue damage to the furnace structure and any variations in conditions such as stirring, slag volume or viscosity which affect the rate at which heat can flow down and away from those exposed surfaces where the heat is first received from the flame. Because a given type of charge in a shop is often considered as being nearly constant in both physical and chemical characteristics from one heat to another, and because such a state of affairs may be thought of as resulting in a reasonably constant net heat requirement, this requirement is usually neglected as an invariable, inevitable matter, about which nothing can be done. With normally variable charge, and variable percentages of limestone and cold pig, however, the net heat requirement can be subject to very appreciable change; it may also be affected by such things as the currently popular procedure of blowing oxygen into the bath. To bring the general problem of production rate into better perspective, therefore, it seems worthwhile to try to evaluate the net bath heat requirement and the amount by which it may change through variation in different factors. Because our calculated values of net heat are admittedly uncertain, we have tried to check them in part by statistical data on actual production rates over rather large groups of commercial heats. The results of calculation of net heat requirements in a wide range of actual commercial practices may first be summarized briefly. We find a wide range between the extremes of different practices, as would be expected, with duplex practice (essentially blown metal plus hot metal) having essentially a zero net heat requirement, an all-cold charge practice somewhat over I million Btu per ton of steel and a high hot metal practice about 0.75 million Btu per ton. Over the commercial range of scrap plus hot metal practice, increasing the percentage of hot metal from 40 to 78 pct, with other factors nearly constant, decreased the net heat by only some 5-10 pct. The net heat is increased by about 1.2 pct for each I pct of the metallic charge present as cold pig. Calculated values of oxygen supplied by air varied from about 25 up to 60 lb per ton of steel, and in a 60 pct hot metal practice, an increase from 32 to 52 Ib oxygen from air decreased the calculated net heat from 0.88 to 0.74 million Btu per ton. Use of pure cold oxygen to substitute for about one half of the total charge ore (about 28 Ib oxygen replacing 145 Ib ore per ton of steel) decreased the

Jan 1, 1949

By G. R. Gray, T. S. Chapman, J. L. Foster

The wall-building properties of salt-water drilling muds can be improved markedly by the addition of: (I) natural gums, such as traga-canth, karaya, and ghatti; (2) seaweeds, such as Irish moss; or (3) gelatinized starch. Results of laboratory tests have been confirmed by field trials. For drilling operations in which the mud becomes contaminated by salt, either through penetrating salt-bearing rocks or by addition of sea water to the mud, the added cost resulting from the use of one of the substances listed above is more than offset by freedom from stuck drill pipe and ease in running casing. Introduction It has been recognized for many years that oil production might be seriously hampered by infiltration of water from the drilling mud.l-4 As knowledge of the mechanism of the wall-building process advanced, methods were developed for evaluating the filtration characteristics of muds.5-ll The wall-building properties of freshwater muds are commonly regulated by the addition of bentonitic clays, or of agents to promote the dispersion of the natural mud solids. When strata bearing soluble salts are encountered in the course of drilling, the salts are incorporated in the mud; the clay solids are flocculated and water loss is increased tremendously. Methods gen-crally used in controlling filtration of freshwater muds are no longer applicable. The problem of reducing water loss from salt-water muds is not confined to any particular area, but is acute in parts of West Texas. Salt beds several hundred feet thick must be penetrated before the oil-bearing formation is reached. Since the formation drilled does not provide mud-making material, it is necessary to use large quantities of commercial clays, and even the best commercial clay does not afford relief from the problem of high filtration. A laboratory study has been made of methods of improving the filtration characteristics of salt-water muds, and some of the methods have been used in field practice. Laboratory Investigations Procedure Inasmuch as the immediate object of the investigation was the development of means of improving the wall-building properties of muds used in West Texas, an attempt was made to employ muds in the laboratory study comparable to those in field use. Samples of muds used in drilling the producing formations in six wells were secured. The properties of these samples are summarized in Table I, which lists the densities, viscosities, filtrations, and analyses of the filtrates for calcium, chloride, and sulphate. Viscosity was measured in the Stormer viscosimeter at 600 r.p.m. Water loss was determined at 80°F. with the Baroid low-pressure wall-building tester8 at a pressure of 100 lb. per sq. in. Filtration rates are considerably higher than those of usual fresh-water muds, which amount to about 20 C.C. in 30 min. Water loss was so rapid in samples 4, 5 and 6 that filtration was complete in less than 10 min. and the values for 30 min. were extrapolated from the rates at shorter

Jan 1, 1942