Search Documents

By WALTER VOIGTLANDER

FOR nearly 100 years wire rope has been fabricated in much the same way. To the great majority of mine superintendents wire rope is just wire rope, little or no semblance of individuality or identifying characteristics. Such an impression was fairly justified until three or four years ago when a practical means was found of performing or preshaping the wires and strands. This discovery permitted a revolutionary change in wire rope manufacture. Instead of merely twisting a number of wires into a strand, then twisting several strands into a complete rope (which twisting would naturally result in great internal strain, thus reducing the resiliency and over-all efficiency of the completed rope), the preformed wires and strands were laid in place without force or twisting. The obvious result was a rope more nearly approximating mechanical perfection. The applied loads are more evenly distributed throughout the component wires and strands, thus reducing unbalanced wire stresses. This results in a higher safety factor. The fact that preformed rope will not unravel when untied at the ends proves the absence of a torsional stress that exists in ordinary rope. A greater useful allowable stress in the wires is therefore possible in actual operating service.

Jan 1, 1926

By V. Koump, T. F. Perzak, R. G. Olsson

Jan 1, 1965

By George Sachs, S. M. Clark, George Espey

he tendency of a commercially drawn cartridge case to crack in the mercury test and the relation of cracking tendency to residual stress retained after drawing were studied. The fourth drawpiece (next to the final) of caliber 0.30 cartridge cases produced by Frankford Arsenal were selected as test pieces. These exhibited an exceptionally high cracking tendency, making a detailed study possible. To obtain fast cracking in the mercury test, about 0.0015 to 0.003 in. must be removed from the wall thickness of the drawpiece by pickling, and it must be subjected to the mercury test immediately after washing. Removal of the adhering mercury by annealing and subsequent squeezing of the case in a vise was used to reveal definitely the presence or absence of cracks. Various lots of apparently identically fabricated cases were shown to possess a different cracking tendency. Machining off or boring a hole in the base gradually reduced and eventually eliminated the cracking tendency. On the contrary, shortening of the wall (body) reduced the cracking tendency only if the wall became so short that the cracking zone was directly affected. By boring out the base and pickling from the outside and then splitting the resulting rings, it was possible to determine the approximate stress distribution in the base and in the adjacent part of the wall. Small compression stresses were present in the core and the major part of the base, while the surface of the base and the adjacent wall contained high circumferential tensile stresses. On the contrary, the wall when parted from the base contained only insignificant residual stress. The conception is advanced, that the stress distribution in a drawn cartridge case corresponds fundamentally to that of a tube (wall) shrunk on a disk (base). Such a stress distribution results from the tendency of the base to recover elastically by an increase in diameter from the biaxial compression during drawing while the wall exhibits little tendency to change its diameter after progressing through the die. This is confirmed by measurements which show the base diameter to be slightly larger than the wall diameter.

Jan 1, 1945

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By Christopher Haycocks, Lawrence P. Johnson, George M. Neall, James M. Townsend

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U. S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. Cambrell and Haynes1 (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and Singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 45°. However, to date, no systematic attempt has been made to establish design criteria. In this paper, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1979

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By G. R. Heckman, H. J. Murphy, C. T. Sims

An incestigation has been made of the effects of heat treatment and alloy composition on the long-time stress-rupture properties and structural stability of the similar nickel-base alloys Udimet-500, Lrdimet-520, and Udimet-700. Rupture test data are presented at stresses ranging from 4 to 50 ksi at temperatures from 1450° to 1900°F for times up to 14,000 hr. Ductility response is emphasized. Optical and electron tnicroscopy were complemented by X-ray diffraction analyses of extracted phases to relate microstructural stability to the observed rupture properties. Particular attention is paid to Udimet-520 since structural characteristics of this alloy appear to vary somewhat from its sister alloys. Both cast and wrought performance of Lrdimet-500 are discussed. The computerized PHACOMP calculational technique, based on electron-vacuncy theory, is discussed and related to structural stability where appropriate. Electron microscopy and microprobe techniques were used to conduct evaluation of the oxidation characteristics of Udimet-500 exposed in air for 16,100 hr. The steady advance in strength and reliability of nickel-base superalloys continues to be one of the high points of modern metallurgy. The stress capability of these materials has increased steadily, allowing higher and higher operating temperatures in the highly sophisticated aircraft and industrial gas turbines now on the market. The attendant increase in efficiency, of course, means greatly improved power output. Gas turbines for industrial and marine use have long been designed with these objectives paramount the usual design requirements in terms of time of service being 100,000 hr. High-efficiency, long-life aircraft such as the supersonic transport require superalloy engine materials with high-strength and long-time structural stability. Thus, materials studied for and operating experience from industrial gas turbines provide a good reservoir from which technology of high value to the SST program can be drawn. This study is one such case. Three prominent nickel-base super alloys—Udimet 500, Udimet 520, and Udimet 700 were extensively evaluated for industrial gas turbine bucket use. Particular attention was directed toward structural stability as a requisite property. Within the present context, structural stability is defined as freedom from the propensity to form strength-robbing or embrittling phases such as u,p,x,or Laves, and the ability to maintain useful rupture strength and ductility throughout design life. MATERIALS The three alloys, cast Udimet 500 (U-500C), Udimet 520, and Udimet 700, were chosen for detailed evaluation based on preliminary studies which indicated that U-500C and U-520 possessed comparable rupture strength capabilities, and that U -700 had a greater strength capability but somewhat poorer ductility than wrought U-500. The nominal compositions of the three alloys, along with the compositions of the heats investigated, are presented in Table I. PROCEDURE Dimensionally rejected U-520 buckets from Special Metals Corp. heat 63370 were heat-treated using the four cycles delineated in Table 11. Cycle A was investigated to determine the effects of a shortened 1700°F primary age. Cycle B was considered a "standard" treatment. Cycle C investigated a higher solution temperature in combination with a shortened primary age, while cycle D assessed the effect of the higher solution temperature alone. These heat treatments were designed to produce optimum combinations of rupture strength and ductility through maximum y' development, the development of a y' grain boundary cushion, promotion of MC carbide degeneration reactions, and agglomeration of resultant M23CB. Since one of the premises of the evaluation of U-520 was that rupture strength would be equivalent to U-500, forged U-500 buckets from Special Metals Corp. heat 62916 were heat-treated with cycles A, B, and C to provide comparison. The heat-treated structures of U-520 and U-500 are illustrated in the 8700 times electron micrographs of Fig. l. The U-700 tested was all from 3-in.-diam hot-rolled and centerless-ground rod from Special Metals Corp. heat 2-1426. Two heat-treatment cycles were employed, E and F of Table 11. Cycle E is a standard four-step, triple-age treatment intended to provide an optimum match of strength and ductility through well-developed matrix and grain boundary y', as recommended by U-700 vendors. Treatment F is a shortened , single-age cycle which could provide a significant processing cost reduction should adequate strength and ductility be maintained. Following heat treatment, rupture specimens of U-500 and U-520 were machined from the buckets and tested. Standard rupture bars of U -700 were machined from the heat-treated rod and rupture-tested. Failed and withdrawn rupture bars were prepared and examined by optical and electron microscopy. Select specimens were electrolytically digested, and the residues analyzed for carbide and topologically close-packed phases using CrKa or CoKo radiation. Of the six different U-500C heats evaluated, five were cast by Misco Precision Casting Co. and one was cast by Haynes Stellite Co. Cast-to-size rupture bars

Jan 1, 1968

By H. J. Gerritsen

From presently available components a portable, rugged, reliable apparatus can be built which will be able to detect methane concentrations of 0.1% and lower in air. Sensitivity and design considerations of the apparatus are given. Ways to build even simpler and cheaper apparatus in the future are indicated. Traditionally the problem of detecting and monitoring the presence of dangerous gases present in small concentrations in air has been a difficult one. Whether canaries,' or sophisticated chemical or thermal conductivity methods are used, they seem to be either slow, cumbersome, or otherwise not completely satis factory. A seemingly natural way of gas detection is to measure the strength of absorption undergone by light of a wavelength that the gas to be detected absorbs. This method has been difficult to apply in view of the low power output over a narrow wavelength range in the infrared from traditional glow bar light sources. Besides, the apparatus to select such a narrow band of wavelengths is quite costly and complex. The use of a laser solves these problems simultaneously. Although a variety of lasers are available to detect a variety of gases (such as carbon monoxide or methane) whose early detection would be desirable, this paper deals exclusively with the use of lasers for methane detection. ABSORPTION SPECTRUM OF METHANE IN AIR The absorption spectrum of pure methane is very well known.2-4 There are four fundamental vibrations, all occurring in the infrared of which only two absorb strongly. They occur at 3.3 µ and 7.7 µ. The absorption spectrum is quite complicated due to the fact that the methane molecule can rotate in a variety of rotational quantum states. These rotational states are furthermore split by anharmonic forces such as the Coriolis force.4 When methane is present in air at atmospheric pressure, much of the very fine structure due to the anharmonic force is washed out since the pressure broadening is of the same magnitude as the splitting due to anharmonicity. For most of the spectrum at 3.3 µ, the rotational lines are typically separated by 0.01µ while the individual linewidth is 0.0001 µ. It is thus very important that the laser emit at a wavelength that coincides with one of these rotational lines. Before elaborating on the point that such a laser exists and how it performs, it is necessary for later discussion to point out that in the

Jan 1, 1967

By Thomas A. Wright

No symposium on die casting could be complete without consideration of the methods of formula and impurity control. No consideration of control would be complete without discussion of that new tool of the analytical chemist and inspector, the quartz spectrograph. Just as there is an increased appreciation of the possible applications of the die-casting process and of die castings, so too is there, slowly but surely, of the spectrograph. At present the role of the instrument might well be compared with that of brass or magnesium die castings. Neither is as widely understood or known as they will be. Product specifications are increasing and are getting more explicit and often more rigid. The designer, metallurgist and production engineer or superintendent will be forced to depend more and more on the chemical laboratory. Sampling, as well as analyses, testing and inspection problems will grow. The chemical laboratory must meet its increased responsibility and use of the spectrograph will become more common. Advantages of increased precision, greater speed, lessened labor and often lower costs cannot be ignored. It will be the purpose of this paper in part to outline the respective fields of chemical and spectrographic analyses and to indicate where one may overlap the other and in part to indicate certain possible sources of contamination of zinc-base die-cast alloys in particular. COMPOSITION Aluminum.-Aluminum die castings are expected to conform to the specifications of the American Society for Testing Materials1† and the Society of Automotive Engineers2. The A.S.T.M. has recognized seven

Jan 1, 1935

By W. M. Weigel

LESS advances in the technology of non-metallic minerals than for several years past mark 1931, and the cause is easily found. The universal depression and decreased markets for non-metallic as well as other mineral commodities has forced the producers to cut out all unnecessary expense and reduce operating costs to a minimum in order to keep going, even on a reduced output, and to prevent insolvency. The result. has been that but 'little research has been carried on, and such as has been completed has in but few cases been put into commercial practice on account of the expense involved in new equipment and plant changes. The trend in the industry has been more economic than technologic, and the greatest effort put on market studies and sales attempts to expand markets and scrutiny of present operating 'practice leading to reduction of cost of production. This tendency has been increased by highly competitive conditions and the buyer's market which has prevailed and to the fact that price has been a greater factor than quality in placing orders. Only in cases where improvements in technology would immediately and effectively reduce costs or where in special cases there was but little competition with almost a monopoly control has actual technical development taken place.

Jan 1, 1932

By AIME AIME

TRANSFER to the Bureau of Mines of the responsibility for conservation and production of helium, and announcement that a proposal has been made to the President for commercial operation of the Los Angeles has attracted new attention to the helium program of the Government. The matter is one in which mining engineers, and the mining industry in general, have a peculiar interest. Helium is a byproduct of the petroleum and natural gas industry. It is found in certain of the natural gases which have themselves been discovered, in the main, in the search for oil. If it is to be produced on a large scale, the conservation and development of the fields will necessarily be done by the men of the oil and gas industry. There is no known or expected source of supply of quantities of commercial importance save in the natural gas fields. Not all gas wells supply helium and none of them supply it in important percentages. If it were necessary to prospect a field, develop it, lay pipe lines and build production plants for the helium alone, the cost would be prohibitive. On that basis helium would necessarily be restricted to essential war uses, where cost is subordinate to need. As a byproduct of the natural gas in certain, at least, of the fields in the United States there is distinct reason for anticipating that it may be produced in amounts and at a cost that will permit its regular use in commercial airships.

Jan 1, 1925

By W. S. Ayres

BACK in the early nineties the old Dickerson iron mine in Morris county, N. J., was operated by a vertical shaft 850 ft. deep and by a continuing slope for more than 1000 ft. more 011 an incline of 65", together making the vertical depth about 1800 ft. I was then the general superintendent there. This mine, named for a former governor of New Jersey, had been worked more or less continuously from long before the American Revolution and up to this particular time. The pumping equipment was of the old-time Cornish type, with its long pump-rods running down the vertical shaft and the slope to the sump at its bottom. It was operated by a large flywheel engine in the engine room and all angles were turned by the usual bobs. Saturday was the day fixed for lowering the "suction" into the deepened sump at the bottom of the advancing slope. The mine foreman had gone down with the morning shift to superintend this very vital and particular work, which consisted not only of lowering the "suction" into the sump immediately after the pump had been stopped, but of securing it to the rock and putting in the added sections of column-pipe and of tightening up the numerous bolts at their joints, all before the water rose to the point of working. At an appointed time during the forenoon I had agreed to go down into the mine and join the mine foreman in consultation over any difficulties that might have arisen. At the time agreed I went down by the cage to the bottom of the vertical 850-ft. shaft, and then by ladders down the slope for over 1000 ft. more.

Jan 1, 1930

By George F. Kunz

Jan 1, 1902

By J. H. Westbrook, R. W. Guard

The influence of a number of alloying additions on the structure and hardness of Ni3Al (?') has been studied. Three general effects have been observed.. solid-solution hardening, strain aging, and defect hardening arising from deviations from stoichiometry. The solid-solution hardening phenomena are complicated relative to binary terminal solid solutions due to the possibility of virtually independent substitution for the component elements and to the concomitant effects of strain aging. In many superior nickel-base high-temperature alloys the elevated temperature strength is attributable to the presence of a dispersion of Ni3A1 (?') in a solid-solution matrix. Examples of such alloys are Inconel X-550, Inco 713, Waspalloy, and Nimonic 80. It is, therefore, appropriate to seek a further understanding of the properties and alloying behavior of this compound. Ni3Al, the compound most rich in nickel in the nickel-aluminum binary system, was first detected by litakal but not established with certainty until the much later studies of Bradley and Taylor' and Alexander and Vaughan.3 More recently the mechanism of formation was clarified by Floyd4 who showed that Ni3Al is the product of a peritectic reaction at 1395°C between the melt and the compound NiAl in agreement with the original suggestion of Alexander and Vaughan.3 Ni3Al has the ordered face-centered-cubic or Cu3Au structure in which the nickel atoms occupy the face centers and the aluminum atoms the cube corners, a0 = 3.570A. Despite earlier reports to the contrary. the compound apparently remains ordered at least to 1000oC.5 It exists over a narrow range of compositions (-3 pct wide) whose limits and temperature dependencies thereof have been reviewed recently by Taylor and Floyd.' Most previous workers have found Ni3Al to be both hard and brittle7,8 although Maxwell and Grala8 obtained 2.5 to 6 pct tensile elongation at room temperature and Alexander and vaughan3 described the material as "hard and tough" on the basis of observations made while preparing metallographic specimens. In a recent study one of the present authors found that although considerable intergranu-lar brittleness was evident: individual grains of a coarse-grained inert atmosphere arc-melted specimen were readily deformable.l0 The same study also showed Ni3Al to have an anomalous temperature dependence of hardness in that such a curve exhibits a number of peaks between room temperature and 800°C which could not be associated with any microscopically observable precipitation reactions or polymorphic transformations. It was, therefore, proposed in the present study to elucidate the anomalous high-temperature strength behavior and to examine the solid-solution alloying of this compound and the effects of such alloying on hardness. Sample Preparation and Experimental Procedure-Samples, both of pure Ni,Al and of various alloyed solid solutions based on Ni3Al, were prepared by arc melting 100-g buttons in an inert atmosphere arc furnace. All buttons were heat treated for 4 hr at 1275oC and examined metallographically for homogeneity. Microstructures were typically homogeneous and single phase with ASTM grain size about 1 and unusually clean grain boundaries. Chemical analyses showed good correspondence (within a few tenths of a percent) with intended compositions. Microindentation hardness data were obtained from room temperature to 800°C in vacuo using a balanced-beam type loading system in an instrument to be described in detail elsewhere." In general a 100-g load, a loading rate of 1 mm per min and an indentation time of 15 sec were used. Various indenter materials were used according to the materials bein tested because of specimen-indenter interaction. Fl Measurements of the Vickers-type indentations were made at room temperature. Hardness-temperature curves were run at least twice on each sample to ensure that surface work-hardening effects had been eliminated." Precision lattice-parameter measurements were made on powder samples using a back-reflection

Jan 1, 1960

By Verne C. Fryklund, S. Warren Hobbs

The Coeur d'Alene district in the panhandle of Idaho is one of the major lead-zinc-silver producing areas in the world. The value of recorded production to date has exceeded $2 billion. Country rock comprises six formations of the fine-grained, highly siliceous, and slightly metamorphosed Precambrian Belt Series. Small stocks of monzonitic rocks and several varieties of dikes intrude the sediments. The district is at the intersection of a north trending major anticlinal uplift and the west northwest-trending Lewis and Clark line of which the Osburn fault is the dominant feature. The district structure is complicated and comprises folds, some of which are overturned, and a complex of faults of diverse ages and directions of movement. Late Cretaceous stocks but are also probably Cretaceous in age. The productive veins are localized within a series of 12 subparallel, straight mineral belts that trend approximately N65°W and that appear to be controlled by deep fractures in the basement rocks. The mineral belts are in two groups, separated by 15 miles of post-mineralization movement on the Osburn fault. Veins and ore shoots are variously disposed within each mineral belt. Many crop out at the surface, but others apex several thousand feet beneath it. Local controls that influence the position of ore shoots within the mineral belts include the brittle character of host rock attitude of bedding relative to the mineralized fracture, and the amount and direction of movement on faults. Depth appears to have had little effect on the occurrence or type of ore. Ore occurs in a series of steeply dipping replacement veins of relatively simple mineralogy. Six periods of mineralization, ranging from Precambrian to Tertiary in age, are recognized. The productive galena sphalerite-bearing and tetrahedrite-bearing veins-of the main period of mineralization-are younger than the

Jan 1, 1968

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By P. W. Bridgman

DURING the war, the Navy undertook the construction, under my direction, of an experimental gun embodying features designed to lessen the cost and time of production. These experiments were initiated after representations as to their, desirability had been offered by myself, by the Naval Consulting Board, and by the National Research Council. The first drawings were made in June, 1917, and the experiment was completed in November, 1918. For the sake of clearness it will pay to recapitulate briefly the fundamental idea of gun construction. It is well known that if a hollow cylinder is subjected to internal fluid pressure, the maximum stress occurs in the inside layers, the outer parts carrying much less than their due share of the stress. This inequality of stress is more pronounced the thicker the walls of the cylinder. If such a cylinder is pushed to the elastic limit, failure in elasticity will take place long before the outer layers have reached the limit of their capacity. Economical use of the material would demand, however, that all parts of the cylinder reach the limits of their capacity simultaneously. This may be brought about, at least in cylinders of not too great thickness, by producing in. the inner layers an initial compression, and in the outer layers an initial tension. The effect of internal pressure is at, first to relieve the compression of the inside layers, while increasing the tension of the outside layers. If the initial stresses are properly distributed, all parts of the cylinder will reach their elastic limits simultaneously, thus giving a cylinder of maximum strength for its weight. In gun construction as hitherto practiced, this initial distribution of stress is produced either by winding the inner tube with wire, a common English practice, or by shrinking hoops over the inner tube, which has been the standard American practice. Either process is long and expensive, particularly with the larger guns, 12- or 14-in., which require

Jan 2, 1920

By Paul M. Tyler

THE winning of metals from Nature has been advanced to a degree of efficiency that commands admiration even in this Machine Age. Economy of human effort underground, in surface plants, and in treatment works, and better means of performing all manner of operations have cut costs and im¬proved products to an extent that seems far beyond the wildest imagin¬ings of those that labored in the days of hand mining and muscular metallurgy. Principles and methods borrowed from other professions and sciences - mechanical engineering, chemistry, and physics-all have con¬tributed to the rapid development of ore production and treatment, but no small part of the achievements must be credited to the free exchange of ideas within the industry itself and mass attack upon problems of mutual concern. The esprit de corps or class consciousness that has contributed so effectively to the progress of the metal industries has been less apparent among nonmetallic mineral producers. As a class they have been handicapped by inadequate contact with the metal-mining fraternity as well as among themselves.

Jan 1, 1935

By Betty J. Laswell, Gerald W. Laswell

The stepped-up pace of US open-pit and surface mining during the 1970's is a direct response by mining firms and equipment manufacturers to rising costs and declining ore grades. In the race for bigger and more efficient machines, rotary drills have emerged as the foremost leader in primary drilling at major US surface operations. At least 12 different manufacturers now offer rotary rigs in the 102- mm-diam. (4-in.) or greater blasthole size range. With capital investment for the larger units quickly approaching $1 million, the question is asked, "What's been the performance record to date of rotary drill rigs operating in North America?" To answer that question, a comprehensive study of rotary blasthole drills was conducted which qualitatively reveals various problem areas inherent in the rotary drill market and indicates some new directions for improvement.

Jan 6, 1978

By Lawrence S. Darken

STAFF: Editor, Gerhord Derge Cornegie Institute of Technology Schenley Pork Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: J. S. Smart, Jr., President; C. C. Long, Past-President; K. L. Fetters, Vice President; T. D. Jones, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: C. L. McCabe, Chairman; H. L. Bishop, K. L. Fetters, J. J. Harwood, W. A. Krivsky, F. C. Longenberg, R. E. Lund, W. 0. Philbrook, L. L. Seigle, R. L. Smith, and F. L. Vogal. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: C. L. McCabe, Chairman; R. E. Lund, Vice-chairman; D. H. Baker, Jr., W. A. Krivsky, R. A. Lewis, Paul Qusneau, A. S. Russell, R, E. Shinkoskey, W. W. Stephens, and M. E. Wadsworth. Institute of Metals Division: L. L.Seigle, Chair-man, P. A. Back, J. J. Backer, l.l. Bessen, J. 0. Betterton, Jr., J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, R. B. Gordon, C. D. Graham, Jr., R. W. Guard, J. C. Gurland, E. L. Harmon, J. J. Hager, A. A. Hendrickson, M. Harmon, J. N. Hobstatter, H. H. Johnson, Jr., H. 5. Kolish, R. R. Nash, T. N. Rhodin, R. H. Richman, W. Rostokar, P. G. Shawmon, C. W. Spencer, L. Slifkin, J. K. Stanley, C. D. Starr, R. Steinitz, and H. C. Stumpf. Iron and Steel Division: H. L. Bishop, Chairman; 2. E. Boni, F. C. Langenberg, J. B. Wagstaff, and T. V. Wainwright. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 29 West 39th Street, New York 18, N. Y. Telephone: PEnnsylvania 6-9220. Subscription PetroleumEngineers,$30 per year for non-AIME members in United States and North, South, and Central America; 332, foreign; $5 for AlME members. Single copies, $4.00, single copies foreign, $5.00. The AlME is not responsible for any statement mode or opinion expressed in its publications . . . Copyright 1%1 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address; AIME New York ..Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts.. .Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 221, Number 4.

Jan 1, 1962