Search Documents

By W. F. Hosford

W. F. Hosford, (Massachusetts Institute of Technology) —evelopment of methods for predicting the plastic anisotropy of textured metals is an important step toward the improvement of properties by texture control. The engineering value of the present analysis is indicated by the good agreement between prediction and experimental findings. The purpose of this discussion, however, is to point out the weakness of the assumptions on which the analysis is based. The authors state that "the relative width and thickness strains are believed to depend only on the slip direction" and accordingly they disregard the orientation of the active slip plane. where E,, cW, and et are the tensile, width, and thickness strains, A,, A,, and At are the angles between the tensile axis x, the width direction w, and the thickness direction t, respectively; and G,, GW, and 4 are the angles between the slip-plane normal and x, w, and t, respectively. Therefore, the ratio of width to thickness strains resulting from slip on a single system would be These relations hold regardless of whether the slip plane is a crystallographic plane of the {110}, (1121, or (123) type or whether noncrystallographic slip occurs. If noncrystallographic slip occurs, it might be reasonable to assume that the effective slip plane is the most highly stressed plane containing the slip direction. In this case the slip direction, S.D., the slip plane normal, S.P.N., and the tensile axis, x, are coplanar (Fig. 19) and the angles are related by following expressions: where 9 is the angle between t and the projection of the slip direction in the w-t plane (igs. 1 and 2). The normal strains, Eq. [9], become

Jan 1, 1963

By H. C. Heard

INTRODUCTION As the world's population expands and nations struggle to better their relative position and standard of living, increased emphasis is being directed to the exploration and production of mineral resources, to the mitigation of natural hazards such as earthquakes and volcanic eruptions, and to geotechnical engineering projects such as high-level nuclear waste disposal, underground military facilities, and transportation tunnels. Several topics are common to all of these endeavors. One is the characterization of the rock mass in situ, including the definition of the initial environment (e.g., temperature, stress, etc.). A second is, depending upon the use of the underground or the desired result, the manner in which the boundary conditions or the environment are to be changed by man. Next, the physicochemical behavior of the rock mass must be measured, or inferred with uncertainty limits placed on this behavior, over the appropriate range of environmental conditions (e.g., temperature, chemistry, etc.) for the application proposed. And last, an appropriate, validated predictive model must be applied to estimate the rock mass response to the perturbation. In the period preceding about 1955, only relatively simple testing of soils and rocks was commonplace, partly because the environment (depth) to which these data were applied was not so extreme as it is at present and partly because less precise predictions of material response were acceptable. Only limited and relatively simple test data seemed to be needed to guide the engineering. At the present time and certainly in the future, as we extend our interaction with the earth's crust to greater depths and impose more extreme perturbations on it, we need a larger body of data, deter- mined under much more complex conditions, in order to make the required predictions. The present societal problem of high-level radioactive waste disposal is a case in point. We in the rock

Jan 1, 1982

By J. C. Jaeger

It frequently happens in engineering and mining situations that "bad" rock is encountered which consists of rock broken up into blocks a few inches or less in diameter by a network of intersecting joints. These joints may be open, or filled by veins of solid material, or covered with weathering products. Essentially, the material consists of an aggregate of small interlocking blocks. In such circumstances, major joint systems usually can be recognised and studied, but there are probably many minor planes of weakness which may cause the blocks to be of almost random shape. It is extremely difficult to determine the properties of such materials. Measurements on small specimens give the properties of the constituent rock and not the jointed material. At the other extreme, the material has occasionally been tested as loose aggregate in large triaxial pots, but this gives no information about the strengthening effect of the interlocking of the small blocks of rock. One simple approach, which has been much used, is to regard the rock as randomly jointed on a small scale and to apply soil mechanics theory to it. In this case, the normal and shear stress at failure are related by [ ] where the coefficient of friction p and the cohesion c will be those of the individual joints. Even in very bad rock, it is usually possible to drill core in small diameters of 1 to 2 in. which will contain a number of joints, both open and filled. The testing of such joints provides one simple method of determining some of the properties of closely jointed rock and will be discussed in detail in the next section. Calculations based on Eg. 1 with values of c and µ obtained in this way may be expected to give a lower limit for the strength of structures in rock.

Jan 1, 1970

By P. B. Bucky

THE purpose of this paper is to present a scientific method for deter-mining the proper span and shape of roof for safe and economical mining; at present, these two vital factors wherever pillars are left to support the roof are determined by local practice or general experience. To develop the method described here, experimental laboratory work was done. The arch adopted was a segment of a circle, a flat roof being considered an arch with an infinite radius. Hitherto, arches have been used underground without the background of stress analysis that generally precedes arch construction on the surface. In many cases results have not been as expected, because of the lack of knowledge of the factors affecting its strength and behavior. A theoretical and experimental study of arches should furnish informa-tion that will make it possible to design safe and economical surface structures as well as underground openings. For example, on the subject of mine drifts and tunnels, the present idea is that arching their backs increases their strength; this paper will indicate that this is not always true, and if it can be shown that under certain conditions arching becomes unnecessary an economic saving will result. In room-and-pillar work a question may arise as to whether arching the roof and gobbing the excavated material will result in timber saving, and a decrease in the dan¬gers from falls of roof. It is to be distinctly understood that each mine must be treated as an individual problem, and that answers to these ques-tions and many others can now be found after experimental laboratory data have been obtained.

Jan 1, 1934

By L. R. Jackson, W. T. Lankford, K. F. Smith

COMMERCIAL steel sheet is prepared by a combination of hot and cold rolling and annealing. This treatment usually results in more or less pronounced anisotropy. The [ ] anisotropy may manifest itself both as preferred orientation and in the manner in which impurities, segregations, and the like, are aligned in the sheet. The type of preferred orientation and the organization of impurities or segregations may affect the elastic moduli, the yield strength, the tensile strength, and almost always the amount of ductility in different directions. In any case, the most important directions concerned in the anisotropy are along the rolling direction, along the width direction, and along the thickness direction. Considerable data exist on the anisotropy of sheet steel as demonstrated by conventional tensile tests; however, few attempts have been made to measure the constants of plastic anisotropy and use them to describe the flow of anisotropic sheet under combined stresses. [ ] In this paper, evidence is presented indicating that plastic flow in anisotropic sheet can be described by the shear-strain energy flow theory provided that the anisotropy is properly taken into account. MATERIALS USED IN THE INVESTIGATION Table I lists the sheet materials used in this investigation and describes the condition in which materials were tested. DESCRIPTION OF TESTS AND TEST METHODS Two types of tests were run-tensile tests and hydraulic-bulge tests. Characteristic parameters of anisotropy were determined from the tension tests by methods which will be described later. In all cases, the tensile test pieces were cut from the same quarter line and adjacent to the bulge test pieces in the sheet in order to minimize

Jan 1, 1948

By N. P. Pinto

Compacting below the recrystallization temperature was studied. Ideal density was attained at 550° to 600°C using 25 tsi. Compacts have strength and hardness higher than cold worked beryllium. The recrystallization temperature of this highly stressed metal is that of cast, cold worked beryllium and appears independent of pressing temperature. THE process metallurgy of beryllium is beset by many difficulties that hinder the production of sound beryllium shapes of controlled properties. Most of these obstacles are traceable directly to the low density, low ductility, and high affinity for oxygen of the metal. Castings are susceptible to cracking and porosity, and controlled grain size is not easily attained, yet is critical to further working. Any process must carefully avoid oxygen pickup. Conventional metallurgical processes, including melting, casting, forging, rolling, and extruding have been treated previously,'" as have the conventional powder metallurgical methods.' More recently, a method has been advanced for producing powder compacts of high density by hot pressing at 1000" to 1100°C, using pressures of 0.25 to 0.5 tons per sq in. (tsi).3 Here, Seybolt and coworkers attained theoretical density of 1.85 grams per cc using pres-sure-temperature combinations of 500 psi-1100°C, 750 psi-1075"C, and higher. The warm pressing of beryllium is a practical method for producing bars of controlled properties and appears to have certain advantages, particularly when high strength and hardness are required. Other investigators have studied the hot pressing of various pure metals, such as copper,"-" gold," iron,10-11 and aluminum." Their results indicate that ideal densities may be attained by compacting at temperatures less than 50 pct of the absolute melt-

Jan 1, 1955

By A. K. Schellinger, R. D. Lalkaka

IF the ball mill is considered only from an energy standpoint, it can be thought of as a converter of kinetic energy into heat energy and surface energy. The law of the conservation of energy must apply to the ball mill as it does to any machine or process in nature. The heat energy output of the ball mill is apparent to any casual observer of the operating mill since the outflow pulp will be appreciably warmer than the inflow water and rock. The rock in the ball mill is crushed by shearing of its ionic bonding caused by some impact-induced stresses beyond the elastic limit. As the bonds holding the mineral crystal lattices together are ruptured, new surface area is created on each unit of which a definite number of unsaturated bonds exist. Such unsaturated energy of bonding may be termed the "surface energy," and is a potential energy figure. This created energy was withdrawn from the ball mill system and represents an absorption, or disappearance of heat. To reduce the size of the rock, surface area must be created and with it the at- tendant characteristic surface energies of the minerals concerned. Thus the creation of surface energy, from an energy viewpoint, is the creation of useful work by the ball mill. Because of the controversial nature of the energy efficiency figures for modern operating ball mills, it seemed worthwhile to approximate the ordinary magnitude of such efficiencies from the above viewpoint. This was done by an energy balance of the three aforementioned forms of energy, kinetic, heat, and surface energy, for two 9Y2x10-ft grate-type ball mills grinding cement raw materials. Kinetic energy input to the balls was approximated as closely as possible while the heat energy output was measured by means of a thermometer and water and rock flow rates. The assumption was made

Jan 1, 1952

By R. M. Rose, D. P. Ferriss, J. Wulff

The effect of orientation on the stresses, nctivation energies, and activation volumes for yielding and plastic flow of tungsten single crystals was investigated. Tensile tests showed the proportional limit to be a function of orientation: crystals whose tensile axes were near the [I10} direction were roughly three times as strong as [loo] crystals. The [ 1101 crystals showed low strain hardening and displayed yield phenomena, whereas the other orientations yielded smoothly and showed considerable strain hardening. The fracture mode was cleavage, except for crystals near the [1101 , many of which gave "chisel" fractures at 300°and 373°K. The activation energy for yielding was approximately one- half an electron; volt at all orientations, and the volume of activation was (12 to 14)b3, except near the [1101, where it was 7b3. Activation volumes generally increased after yielding. The most common theoretical models for yielding and strain hardening of bcc metals were. found to be insufficient to the intepretation of the observations here in. An explanation is proposed, based on the dislocation reaction dislocation networks and jogs, md jogs formed during plus tic flow. PRECLSE knowledge of the Drocesses involved in the yielding and plastic flow of the refractory metals is essential to the formulation of models for their flow and fracture. Despite this need, the single -crystal investigations, especially of tungsten, have been sparse. Slip occurs at low temperature, according to schadler,i in <111> directions on {110) planes; as the temperature rises to room tempera-

Jan 1, 1962

By D. R. Walker, M. C. Shaw

THE laws of comminution of Kick and Rittinger have been debated for many years. Certain data obtained from ball mill and drop tests are found to be in approximate agreement with Rittinger&apos;s law while other data would seem to support Kick&apos;s law. In all these tests the energy required to produce a wide variety of particle sizes has been studied. Surface area has also been measured with considerable difficulty, at first because it was thought that the energy associated with crushing was that required to create new surface, later because of precedent and because a more fundamental variable was unknown. Tests made with the machine shop type of grinding process show that normally brittle materials that are usually crushed can behave like the more ductile metals. Brittleness is then a relative property largely dependent on specimen size and stress state. The machine grinding operation offers a convenient means for studying the comminution of materials in which the important size variable retains its identity. The energy required to grind a certain volume of material is shown to be strongly de- pendent on size. Kick&apos;s law is found to hold very well for particles below 1 micron in size, while Rittinger&apos;s law holds approximately in the comminution of larger particles. While a physical origin of Kick&apos;s law is established in terms of the theoretical strength of materials having a perfect lattice structure, there is found to be no physical basis for Rittinger&apos;s law.

Jan 3, 1954

By W. F. Brace, James D. Byerlee

Although prediction of failure of rocks may be ultimately possible without knowing in detail how failure occurs, understanding of this process is certainly of fundamental interest in rock mechanics. Of the various failure mechanisms, probably brittle fracture is of greatest interest. Recent reviews have brought this subject nearly up to date (Hock,1 Price,2 and Jaeger 3) and here, we summarize certain recent developments. As our understanding of brittle fracture is derived almost solely from laboratory studies this will amount to a review of certain laboratory experiments. New studies in four areas are pertinent; these concern 1) the volume changes which accompany brittle fracture, 2) the propagation of cracks in compression, 3) certain frictional characteristics of rocks and minerals at high pressure, and 4) the law of effective stress for crystalline rocks. Our objective here is less to present an entirely consistent, complete picture of how a rock fractures than it is to emphasize gaps in our understanding and, thus, suggest areas that need further study. Progress is still painfully slow in this field and perhaps this approach will stimulate new work. OBSERVATIONS Although the behavior of large rock masses is most often the concern in rock mechanics, the number of large-scale experimental tests is still vanishingly small. Our experimental observations arc, by and large, still made on small, relatively flaw-free, rock samples. Here also we report the behavior of small samples.

Jan 1, 1967

By Charles T. Holland

IN connection with the problems of bumps in coal mines, much has been written concerning the manner in which roof action and methods of mining enter [ ] into the pressure effects observed but little has been written upon the relationship between the physical properties of coal and associated rocks and the cause of bumps. The question of the strength of bituminous coal, of its elasticity, and the energy it can absorb and store has been neglected to a considerable extent in connection with this problem. STRENGTH OF COAL It is generally agreed that one of the necessary conditions for bumps is a strong [ ] coal.1 Therefore, since the strength of coal is an important factor, a study of this property should be made. Several investigators have conducted laboratory experiments upon the strength of coal, using small cubical or rectangular test pieces. An attempt will not be made to go into all of these investigations, but they are briefly summarized in Table I. Experiments of the U. S. Bureau of Mines8 and of Lawall and Holland (pp. 27 and 34 of ref. 9), however, indicate that regardless of whether the coal is a soft and weak semibituminous (Pocahontas No. 3) or a hard and strong bituminous (Stockton) coal, the maximum ultimate unit stress developed in laboratory tests is higher in small cubes than in larger cubes of the same coal.

Jan 1, 1942

By H. F. Yancey, O. L. Furse

For several years the Bureau of Mines at its Northwest Experiment Station, in cooperation with the Mines Department. of the University of Washington, has been studying the breakage and degradation of coal. The first phase of the study was devoted to the determination of the friability of many coals of various ranks and comparison of various methods for estimating friability.&apos; A study of the relative ease or difficulty with which various coals are reduced to the fine size required for use as pulverized fuel followed the completion of this work. Baltzer and Hudson2 list twelve research organizations in the United States, two in England, one in Germany and one in Canada that are reported to be engaged on this problem; showing the general appreciation of the need for a simple method of estimating the grindability of different coals. Hardgrove,3 ho has advanced a method for estimating grindability, points out that pulverizer tests of different coals are incomplete and unsatisfactory. He compares such tests to that of a boiler test made without knowledge of the calorific value of the coal. Frisch arid Holder4 also stress the same point. They state that,

Jan 1, 1934

By Chester Washburne

RECENTLY, Messrs. Mills and Wells1 published a thorough chemical study of the waters associated with oil in parts of the Pennsylvania, Ohio, and West Virginia region. Many of their conclusions are of general application and the writer wishes to discuss some of these: Messrs. Mills and Wells show that the composition of the deep brines of the Appalachian fields is such as would be produced by the evaporation of sea water and the precipitation of sodium chloride, combined with reactions with hydrocarbons and other substances. The brines are altered, also, by considerable mixing with meteoric water. They give good reasons for believing that the concentration of the brines was produced by evaporation in the rock pores induced by migrating gas, much of which probably escaped to the surface of the ground. This hypothesis was considered by the writer in a former paper,2 in which main stress was laid on a second hypothesis, that the excess of chlorine in the deep brines may have been due to the entrance of solutions rich in magnesium and calcium chloride which ascended .from a deep, possibly intratelluric, source. Messrs: Mills and Wells present good arguments for the first hypothesis. Underground evaporation by ascending gases probably will be accepted as the best available explanation of the concentration and composition of deep well waters. They have not considered the possibility that, salt waters in deep sands may be concentrated by the diffusion of water vapor through gas into shale. The writer has given reasons3-for believing that capillary forces concentrate gas and oil in the larger openings of rock, such as the pores of sandstones embedded in shale. The gas underground must be nearly saturated with water vapor at; all times, because it always is in contact with the interstitial water of enclosing shales and of the sand-

Jan 9, 1920

By B. T. Brady

Experimental data 1,2 on the energy dissipation in polycrystalline materials over a large frequency spectrum (10-2 cps to 106 cps) suggests that the quality factor [(e= Q )] is independent of the frequency providing both fluid-saturated and ferromagnetic materials are excluded from the test data. Additional data 3 suggest that the quality factors are less at high pressures than at low pressure, i.e., Q increases as the pressure increases. Observations on the dissipation of single quartz crystals with their polycrystalline counterparts indicate that the energy dissipation is less for the single crystal than for the aggregate .2 Both of the above observations, particularly the latter, are indicative of the fact that the dissipation increases with increasing surface contact within the polycrystal, i.e., a frictional attenuation scheme may be operative. Knopoff and MacDonald 4 have shown that a friction model gives rise to a quality factor frequency independence property. A partial listing of some values of Q, observed for both metals and non-metals, is given in Tables I, II, and III. In Tables I and II, the data all show Qs>Qp, i.e., the energy loss per cycle for compressional body waves is greater than that for shear waves of the same frequency. Most samples in Table III show the same effect. It is objective of this paper to suggest: (1) a frictional attenuation scheme may account for the observed losses incurred during the propagation of low amplitude stress waves in dry brittle rock and, in particular, that such a scheme can account for the observed relative magnitudes of the quality factors for P and S wave motion; (2) a friction scheme can readily explain the difference between the dynamic and static moduli in dry brittle rock; (3) a friction scheme, while in itself an intrinsically

Jan 1, 1968

By R. C. Hirschfeld, H. H. Einstein, R. W. Bruhn, R. A. Nelson

The objective of the model studies described in this paper is to determine the effect of planar discontinuities on the strength and deformability of a rock mass. A model material was used because it satisfied concurrently three requirements that available natural-rock samples did not: (1) low strength, which was desirable for minimizing the loads that had to be applied in the laboratory; (2) ease of producing test specimens with geometrically regular joint patterns; and (3) uniformity of the test specimens. The model tests were performed on specimens made from a single modeling material and tested under triaxial stress conditions with [u,=u,]. Results are presented in this paper for tests on specimens that had (1) a single joint set inclined at several angles to the major principal direction, including 0º and 90°, and (2) two joint sets that were mutually perpendicular, one set perpendicular to and one set parallel to the major principal direction. Several different joint spacings were used in each series. Future tests will include a series with two sets of joints that make oblique angles with each other and with the major principal direction. The results of model tests and tests on cores of jointed rock by several investigators (e.g., Müller and Pacher,l Moore,2 Krsmanovic and Milic,3 Hayashi,4 Rosenblad,5 Jaeger,6 and Lane and Heck 7, have contributed significantly to the design of these experiments, which are believed to be the first in which a comprehensive study has been made of the combined effects under triaxial loading of joint spacing and joint orientation (Fig. 1).

Jan 1, 1970

By Frank R. Milliken

This paper is a running commentary on metallurgical problems and developments, stressing ilmenite flotation, since the start of operations five years ago, at the mill of National Lead Company, Titanium Division, MacIntyre Development, Tahawus, New York. In early 1941, when world conditions threatened to cut off the supply of ilmenite (obtained largely from India) to this country, the National Lead Company started to develop and bring into production their MacIntyre Development. This operation supplied the bulk of the ilmenite used during the war period for the manufacture of the much needed titanium pigments. MacIntyre Development is at Tahawus, New York, on the headwaters of the Hud- son River in the center of the scenic Adirondack Mountains. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. Operating tonnages and production have increased since 1943, however. Nearly 10,000 tons of.ore and waste is broken and loaded daily in the open-pit mine. About half of this tonnage is ore, from which is produced nearly 800 tons of ilmenite concentrate and 1600 tons of magnetite concentrate daily. Ore—types From an ore-dressing standpoint, there are five rather distinct ore types and two waste-rock types in the mine. The ore types are shown in Table I. The anorthosite waste is a coarse-grained white rock, largely labradorite feldspar. The gabbro waste is generally finer grained, and contains, in addition to feldspar, 35 to 75 pct iron silicates such as hornblende, in garnet and biotite. A minor mineral mineralogically, but important metallurgically, is apatite. A few calcite

Jan 1, 1949

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By Harrison Schmitt

IN the practice of ore finding the geologist is continually confronted with the question of oreshoot extension, so that the general problem seems worthy of systematic investigation. This problem appears when the reserves are estimated and when the advisability of deepening the shaft comes up. Moreover, there is need for lower development cost to keep pace with cost reductions in other departments, or even to offset a rising cost of ore finding or ore following. This can be gained by close geologic control of the development; and much of the geology involved is that bearing on the downward, upward, and horizontal extensions of shoots. Furthermore, the purchase of a mine or prospect often depends directly on the question of shoot extension; because it is seldom that the ore is fully developed and the purchase price is almost invariably based largely on "possible" and geologically prospective ore. Most current methods for estimating &apos;(possible" and the more nebulous classes of ore are crude and indecisive. In the following pages the extension of oreshoots is the major theme, although the more basic subject, the general art of ore finding, is given some space. (A) Direct Methods of Extension Prediction (I) Extrapolation and Interpolation of Shoots by Use of Conventional Geologic and Assay Plans, Projections and Cross-sections There is little need for stressing the desirability of detailed geologic plans, assay plans, projections, and cross-sections as a basis for the study and extension prediction of shoots. Underground and surface mapping, in most cases, ought to be done in exhaustive detail. All features of obvious bearing should be mapped and it is good practice to record all possible details, some of which may become significant when studied in the ensemble. It should be emphasized that the mapping should be done with an impartial mind, with interpretation reduced to the minimum. The symbols of the map can be made to distinguish observed facts from interpretation.

Jan 1, 1929

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,&apos; Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer&apos;s suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By Clyde Longyear

DURING the last two years, the diamond core drill has come rapidly to the front as a very valuable auxiliary to the equipment of the exploration and production departments of oil companies. The diamond drill and the rotary oil drill work on the same general principles, the essential difference being that the diamond drill employs an annular steel bit set with black diamonds ("carbons"), instead of the fish-tail or other type of bit employed by the rotary drill. On account of the brittleness of the carbon and the danger of breakage if subjected to sudden blows or stresses, it is not practicable to attach a diamond bit and core-barrel to the end of a rotary drill stem. The operating mechanism of the diamond drill must be subject to much more sensitive control than the rotary drill. The bit must be rotated smoothly, without the jerks that are incident to the operation of the clutches and chain drives on the rotary draw works, and the feed must be con-trolled in a much more delicate manner than the mere action of a brake on a hoist. To accomplish this smooth rotation, diamond drills are usually built as a self-con-tained unit with the crank shaft of the engine geared direct to the drive shaft that turns the drill rods or stem. One or two hydraulic cylinders connected with a high-pressure pump control the feed so definitely that the bit can be raised or lowered at will, while the bit is rotating, by the simple operation of valves. The smaller-sized-drills for very shallow work usually have a screw feed control instead of the hydraulic feed. The principal uses of the diamond drill in oil work are three: 1. Reconnaissance or structure drilling; that is, the drilling of a number of shallow holes to ascertain the subsurface contour. 2. Scout drilling, or the drilling of holes of smaller diameter than is required for production, to obtain information as to the character of the oil sand and the quality of the oil. 3. Drilling producing wells.

Jan 5, 1923