Search Documents

By Robert :H. . Lesemann

I recently gave a talk at a seminar on mine development in the Eighties. I had to present CRU' s long-range market outlook for copper, lead, zinc, nickel, molybdenum and silver. In reviewing the recent history of each metal, and our projections, I tried to find some common pattern of behavior that could prove a guide in projecting future market behavior. When you sweep aside your input-output models and econometric equations, what you seem to be left with is this: "When a market goes through a prolonged period of price weakness, you can usually look forward to a period of considerable improvement. " "When a market goes through a prolonged period of price strength, you can always anticipate a prolonged period of price weakness." Stated another way, "The better things are, the worse they will get."

Jan 1, 1982

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By R. E. Cech

Metallographic observations on hydrogen-reduced nickel oxide crystals suggest that nucleation of nickel occurs at structural singularities in the oxide. The fully reduced structure contains micron-diameter, worm-like voids occupying 40 to 50 pct of the volume. The crystallographic orientation relationships between nickel oxide and nickel resulting from oxide reduction are recorded and discussed. THE process of reduction of oxide to metal is one of considerable complexity involving a chemical reduction reaction, mass transport of reducing agent to the point of reaction and of reaction product away from it, and finally a transformation whereby metal atoms released from the oxide rearrange to form a stable reduced phase. In addition, nucleation of the reduced phase affects the overall reaction kinetics. Thus far only the thermodynamic aspect of reduction has received the attention warranted by the importance of

Jan 1, 1960

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45' to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;' Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.'-' It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer' has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

THE purpose of this chapter is to present a general outline of the basic open-hearth process for the benefit of students, practicing open-hearth operators, and metallurgists who wish to review the subject. The discussion is limited to a description of the sequence and purpose of the operations, illustrated by data and examples. Subsequent chapters deal with more detailed and fundamental studies of the subject. The function of the basic open-hearth furnace is to convert various types of ferrous material into finished steel of given com- position and quality. In comparison with other steelmaking methods, the basic open-hearth process is one of the most versa- tile, both from the standpoint of the raw materials that can be used and the types of steel that can be produced. The process can be considered as a sequence involving melting, refining, and deoxidation. With some types of liquid-metal charges, the melting stage is not present, but refining and deoxidation in varying degrees are fundamental features of the process. GENERAL DISCUSSION OF BASIC OPEN-HEARTH PROCESS The first consideration in open-hearth practice is the type of charge on which the operation is based. This consists of three components-fluxing, oxidizing, and metallic materials. Fluxes. In the basic process the fluxing material is primarily lime, added in the form of either limestone (CaC03) or burnt lime (CaO) . This is supplemented by magnesia (MgO) and lime from the furnace bottom and banks. The function of these fluxes is to form a slag with the silica (SiO2) , manganese oxide (MnO), iron oxides (FeO and Fe203), and phosphorus oxide (P205) that are produced by the oxidation of varying amounts of the silicon, manganese, iron, and phosphorus in the charge during melting and refining. The slag, composed of the basic fluxes and the neutral and acid oxides, floats on top of the steel bath when the charge is melted. The composition of this slag depends on the amount of each slag-forming element present in the charge and on the extent of oxidation of these elements during the course

Jan 1, 1964

By Harry C. Wiess

RECENT announcement of further restrictions on gasoline consumption in the Mid-West and Southwest has focused public attention on current discussions of an oil scarcity. Conflicting arguments are advanced on the one hand that we have plenty of oil and will not need to restrict consumption as soon as transportation facilities are adequate, and on the other hand that a great impending shortage will require most drastic reductions in civilian consumption in order to provide adequate supplies for military purposes. Data can be presented to support both views, the result being that the public is confused and uncertain of where the truth lies. For a nation with about half of the known crude-oil reserves of the world and two thirds of the total production it seems almost incredible to the layman that any shortage can exist. Those familiar with estimates of future demand. however. show increasing concern regarding our ability to meet military demands without further restrictions in civilian use or wasteful production from our remaining reserves. Only by considering such facts as are available and can be made public can a true appraisal be made of whether or not we are faced with a shortage that will amount to a crisis in crude oil.

Jan 1, 1943

By C. H. Mathewson

CHARACTER OF THE WORK IN HAND IN planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100° C. to 1,000° C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,1 in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper.

Jan 7, 1916

By Krahmann, Rudolf

THE following is an account of a survey undertaken to test the possibility of outlining a kimberlite pipe by magnetouietric methods. Kimberlite is a basic igneous rock closely related to melilite-basalt or alnoite, which occurs either in the form of volcanic plugs or as dikes intruded into rocks of various types and geological ages up to and includ¬ing the Lower Cretaceous. The famous diamond mines of South Africa are all in kimberlite pipes and these pipes are probably the original source as well of the vast alluvial deposits found in various parts of the country. The pipe chosen for this experiment is one that ' occurs on the farm Goedgevonden No. 20, about sixteen miles north of the village of Klerksdorp and ninety miles southwest of Johannesburg. Some prospecting has been done on this pipe and diamonds were produced from it but not in paying quantities. The magnetometric survey was made in June, 1932, by R. Krahmann and H. Wallisch and the results are shown on the accompanying plan. On the plan are shown also the boundaries of the pipe as exposed at the surface and details in regard to the surrounding foundations. These are taken from a geological survey made at a later date by W. Beetz, of Johannesburg.

Jan 1, 1935

By Oliver Bololes

UNDER the able leadership of Samuel H. Dolbear, the Committee on Nonmetallic Minerals furnished a program of sixteen papers comprising three sessions. An outstanding accomplishment in technology presented at the first session by Benjamin L. Miller and C. H. Breerwood is the application of flotation to the purification of limestone used in cement manufacture. In place of selective quarrying to provide high-grade raw material, the quarry-run stone is pulverized and treated in froth flotation cells for removal of free silica and mica. Some advantages are cheaper quarrying, more complete utilization of quarry rock, avoidance of purchasing high calcium stone, lower fuel cost and improvement in the finished cement. Paul M. Tyler presented the general subject of milling methods as applied to nonmetal lies. He pointed out the importance of some of the more recent refinements in ore dressing, and urged the need of a wider appreciation of their possibilities. The gypsum industry of Canada was described by L. H. Cole. Crystal growth during the setting process was illustrated by moving pictures. The Coastal Plain and interior salt

Jan 1, 1935

By John T., Ryan

THE subject assigned me, "Safety in Mining," is a very broad one and only the high spots can be covered in this short paper. As this is a meeting of the Coal Division, these remarks will be directed largely to coal mine safety, although the principles of safety and effective accident prevention methods are relatively the same in every branch of mining or industrial work. The coal mining industry should take pride in the part it has played in the development of the accident prevention movement, and there is ample proof for the statement that the first real organized accident prevention, work, both abroad and in this country, was con- ducted in the coal mining industry.

Jan 1, 1930

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By W. M. Raynor

LARGE quantities of "midnight oil" have been consumed by researchers in attempting to develop a process to produce cold ductile zirconium at low cost. The tantalizing facts that zirconium is a bright, silvery, tarnish-proof metal and is 2 1/2 times as abundant in the earth's crust as copper, and thirteen times as plentiful as lead have resulted in much speculation on uses, ranging from automobile radiator grills to kitchen sinks. but unfortunately no low-cost process of producing it has so far been found. In the case of zirconium, we cannot say that "virtue is its own reward" for the principal virtues of the metal, namely, corrosion resistance at ordinary temperatures and ability to absorb gases at high temperature, are the very characteristics that defeat all of the usual recovery methods such as sintering, plating, or direct chemical reduction. The only method giving a pure metal sufficiently low in oxides, nitrides, etc. to be truly cold-malleable is the one developed by Van Arkel and DeBoer in 1925. This process involves decomposition of zirconium tetraiodide in contact with a hot filament and pre

Jan 1, 1947

By R. J. Hopkins, L. B. Haney

On the basis of limited experimental work conducted at the Port Pirie smelter, it would appear that, by increasing the specific surface of sinter, and possibly that of coke as well, a marked increase in the rate and degree of sinter reduction in the furnace shaft can be achieved. Fusion-point tests have shown that this increased reduction means a much higher sinter fusion point and narrower plastic zone, while the more efficient utilization of coke in the furnace is inherent in the intensification of reduction by the provision of a more reactive sinter surface. Investigations aimed at increasing the ability to operate the blast furnace with a higher lead tenor of sinter reducing fuel cost proportionately, and at eliminating the loss in reduction potential in coke entering the furnace, as shown by the presence of appreciable proportions of CO in the top gases, are reported. Several lines for future investigations that could result in improved smelting methods are proposed. A SOMEWHAT informal presentation of ideas on lead blast-furnace smelting will be given in this paper. These ideas have been developed during observations of furnace behavior at Port Pirie and earlier at Mt. Isa, and have been guided by the results of laboratory experiments at Port Pirie. The authors do not intend to propound any particularly new theories, but present their ideas as a basis for discussion which may help toward a better understanding and improved control of blast-furnace operation. Performance variations of considerable magnitude occur from time to time at most lead blast-furnace plants. While Port Pirie is fortunate in having a very regular supply of high grade concentrates, it is no exception in this respect. Such irregularities are of considerable economic importance and they constitute a challenge to present-day metallurgists in their efforts to obtain an ever greater degree of control over furnace operation. In operating as Port Pirie does with a relatively high lead charge, it has been recognized for a long time that shaft conditions are ,of the greatest importance. A practical, or engineering, attack on the problem of accretions consisted of changes in furnace design, e.g., by widening the shaft to 10 ft above the bottom row of tuyeres, and by the provision of curved ends and vertical walls.' That this attack has had a great measure of success is shown by the fact that barring down of these wide furnaces is rarely necessary, shaft conditions have greatly improved, and sensitivity to charge variations has been markedly reduced. These modifications, followed by some metallurgical changes (chiefly the incorporation of pig iron into the furnace charge in 1948), have brought furnace operation to a point where some variables which were previously masked can now be studied. Accordingly, over different periods of time during the last five years, such variables as could be given numerical values have been recorded and subjected to statistical examination. The objectives of this work were: 1—to reveal the true importance of the different variables and 2—to show the proportion of total furnace variation which is unexplained and therefore referable to causes not measured at present? e.g., shaft accretions, sinter structure, coke structure, and others. Statistical Study of Variables In this work factors relating to furnace speed and lead reduction have been examined: 1—slag com-

Jan 1, 1955

By G. H. Tausch, T. A. Huber

Very encouraging progress has been made ill the develop-ment of the permanent-type well completion which decreases considerable the cost of completions and workovers and aid-in the acquisition of reliable reservoir information at low cost. Completion and remedial operations are performed with tool,; which pass through the well tubing. Perforating and plug-hack operations can be done with the tubing in place and do not require pipe-handling equipment. Because of the many advantages afforded by this method, development work is going forward in anticipation of ultimately being able 10 use it to perform all usual well completion and workover operations. Effort is also being directed to the development of a more permanent type of lift equipment suitable for use with the permanent-type well completion. INTRODUCTION The permanent-type well completion in one in which the tubing and well-head are set in place only once in the life of the well and the completion or remedial work is performed through the tubing with a tubing-type perforator. a retrievable tubing extension. and other wire-line tools. This new type completion has made possible the saving of one to two days' rig time in the completion of each of several hundred wells During the last two years, and use of equipment developed for this type of completion has resulted in a 75 per cent reduction in cost. of certain types of workovers. In addition. the more reliable indication of the commercial value of a reservoir and the more accurate general reservoir information made Possible promise to be of even greater value in oil recovery than the reduction of costs for completions and workovers Recently. several well.. were worked over by using the retrievable tubing extension suspended on a swab line to plug back with cement and then perforating a higher producing interval with the tubing-type perforator, thus opening the way for complete through-the-tubing workovers which may be performed without pipe-handling equipment or mud. Those items attendant to the use of pipe-handling equipment and mud. such as hoard matting rig substructure. and pits. were also eliminated. There are indications that the elimination of drilling mud during completion and workover operations will frequently give increased well productivity, as plugging of the perforation. will not occur. It ii now possible to perforate selectively small sections of the producing interval and to test a well through these sections prior to perforating more interval. The perforating of additional interval will not entail the costly operations of killing the well and pulling tubing, nor will the old or the new perforations be plugged. The productivity of .mall sections of a reservoir and the actual gas-oil or oil-water contacts may now be determined economically under flowing condition.. Selective completions can be made in this manner to delay gas and water problems and bring about maximum oil recovery. At the present time, gas lift appears to offer the greatest potentialities for artificial lift in the permanent-type well com"letion since it can provide full-open tubing to accommodate the through-the-tubing tools and it may be ultimately developed into a fairly permanent type of lift. With precent-day pas-lift equipment. valve or mandrel failure necessitates occacio11al removal of the tubing. thereby reducing to some extent the permanence of the completion. New gas-lift valves are now

Jan 1, 1953

By Haydn H. Murray, Sam H. Patterson

The term "clay" is somewhat ambiguous un¬less specifically defined, because it is used in three ways: (1) as a diverse group of fine-¬grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term "clay" realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define be¬cause of the wide variety of materials that com¬pose it; therefore, the definition must be gen¬eral. Clay is a natural earthy, fine-grained ma¬terial composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many defini¬tions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales, Soil investigators and mineralogists gen¬erally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than ap¬proximately 4 micrometers. Some authorities find it convenient to use the term "clay" for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or ar¬gillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally un¬derstood by those who use it. Clay is an abun¬dant natural raw material, and it has an amaz¬ing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial min¬erals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1970, 1971, and 1972 production and values according to the U.S. Bureau of Mines (Ampian, 1972). Adequate reliable statistical data on which to summarize world production of clay are un¬available; this paragraph outlines the world re¬quirements for clay only in a very general way. According to one estimate, the world bentonite production in 1972 was 3.5 million tons (Anon., 1973a), but in the authors' opinion it was prob¬ably at least 5 million tons. The total fuller's earth produced was at least 1.5 million tons and may have been as much as 2 million tons. The total world kaolin production in 1972 was more than 10 million tons. Approximately 7 million tons of this total was produced in only two regions-the Georgia-South Carolina kaolin belt in the United States and the Cornwall re¬gion, United Kingdom. The world's 1972 out¬put of ball clay, which is also produced pri¬marily in the United States and the United Kingdom, was approximately 1.5 million tons or perhaps a little more. The total world fire clay production in 1972 was probably about one and one-half to two times and the miscellaneous clay production three times the United States production. As industrial minerals, clays are a complex group that consists of several mineral commodi¬ties, each having somewhat different mineral¬ogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized

Jan 1, 1975

By Anthony Folger, Howard R. Lowe, J. F. Dougherty, E. G. Trostel, Joffre Meyer

The status of the natural gas industry in Alberta, Canada, is described with particular reference to the current extent of natural gas reserves and possibilities for additional development. Certain major fields are discussed as representative of the types of gas accumulations within various broad geographical divisions of the provinces. The estimation of the future performance of a gas reservoir is discussed as the basis for an estimate of the future availability of natural gas from presently known reserves. The future availability of the provincial reserves and the estimated future demand for gas within the province are described. INTRODUCTION This paper is a condensation of a detailed study of the natural gas reserves and the future availability of pipeline gas in the province of Alberta as prepared for Trans-Canada Pipe Lines Limited and presented in public hearings at Edmonton and Calgary before the Petroleum and Natural Gas Conservation Board of the Province of Alberta. The study began in October, 1950, and resulted in the preparation of five volumes of data at the expenditure of more than 20,000 man-hours. This paper is designed to afford a broad picture with detail limited to a type example of both natural ga-accumulation and future availability of gas supply. The province of Alberta has an area of 255.285 square miles which, for sake of comparison. is 8,359 square miles smaller than the state of Texas. Natural gas was first discovered in 1883 at the now abandoned Alderson well located some 20 miles southeast of the town of Princess. The first gas in commercial quantities was found at Medicine Hat in 1890. During the last 68 years. 187 localities have been discovered which are capable of gas production, and 73 per cent of these have been found since 1945. Sixty fields currently are producing gas, including 22 non-associated gas accumulations. Location of the oil and gas fields and prospects in the province of Alberta is shown in Fig. 1, together with a list of the localities of measurable gas, Fig. 1A. The estimated total provincial gas reserve as of Jan. 1, 1952, for the 104 fields estimated, is 11.7 trillion cu ft proved and probable, and for the 187 known areas capable of production is in excess of 16 trillion cu ft on a total proved, probable, and possible basis. Five fields (Pincher Creek, Leduc-Woodbend, Viking-Kinsella, Cessford and Medicine Hat) are estimated to have recoverable reserves of more than one trillion cu ft each. A sixth field, Turner Valley, was initially in this group, but its reserves have been depleted substantially. Twenty-four fields, of which the above mentioned six fields are a part, have estimated gas reserves (including the possible category) in excess of 100 billion cu ft. These 24 fields account for 79 per cent of the total provincial reserves. Comparative systemic analyses reflect that 56 per cant of Alberta's gas reserves are contained in sediments of Cretaceous age; 30 per cent in sediments of Mississippian age; 10 per cent in sediments of Devonian age; three per cent in sediments of Triassic age; and the remaining one per cent in Jurassic and Permo-Pennsylvanian sediments. It is expected that the relative importance of the Mississippian, Devonian, and Triassic sediments will be increased as exploration progresses. GENERAL GEOLOGY The western Canada basin comprises the sedimentary area between the Canadian Shield and the Rocky Mountain Front Range, the Arctic Ocean, and the International Boundary. The basin has an approximate area of 765,000 square miles and embraces parts of the provinces of Manitoba. Saskatchewan. Alberta, British Columbia and the Northwest Territories. Generalized columnar sections for the Province of Alberta are shown in Fig. 2. Substantially all of Alberta, except its northeast corner, has sedimentary cover. Sediments of all the geologic systems are represented. except those of Silurian age.

Jan 1, 1952

By Arthur Connolly

WHEN scientific literature was lacking or meager, research necessarily meant laboratory investigation above all else. Today, scientific literature has attained tremendous proportions, and the volume increases at a much faster rate than it is digested and efficiently utilized. For that reason the present-day research worker should spend much more time in the library, and correspondingly less in the laboratory, than is the general custom. Library research would overcome two serious errors often made by scientists: duplication of work described completely and failure to appreciate inventions described almost verbatim in the literature. To emphasize these failings that often occur in present-day research, consider a hypothetical scientist as he conducts his search from inception to the stage where it is made available to the public by patent or other publication.

Jan 1, 1942

By L. A. Cowan

IF the elements of personality be those characteristics in which humans differ, and if this definition be applied to the purchasing department for the Climax operations in Colorado, it must he concluded that this department has no distinguishing traits that would give it a departmental personality different from that possessed by the similar department of any progressive mining enterprise. Or, one may go further by stating that the rudimentary functions of any purchasing practice employed principally in the acquisition of maintenance, repair, and operating supplies are much alike, whether or not the industry involved be mining or milling. However, in the fact that the principal purchases of a mining company are materials for maintenance and repair and consumable operating supplies lies that essential characteristic which differentiates mining and milling purchasing functions from those of the manufacturer, the fabricator, or the ordinary processor.

Jan 1, 1946

By W. K. Godfrey

The highest compressive strength cement has the highest bond strength in tests in which the cement is subjected to a confining pressure. After perforating, the bond strength is reduced to nearly zero when the pipe is supported by weak cement. Perforating does not affect the bond strength, however, when the pipe is supported by strong cement. Pipe supported by weak cement is damaged by perforating with expendable capsule jets, but is not damaged by perforating with the hollow carrier gun. High strength cements are recommended for oil wells that are to be perforated. Introduction The purpose of this work is to determine the effect of jet perforating on the bonding strength of oilwell cement at simulated down-hole conditions. Bond strength is a good criterion for determining the effectiveness of cement in performing its main function, i.e., that of isolating zones. According to the literature on the subject, the optimum cement strength for perforating is low and should not exceed 2,000 psi compressive strength. This conclusion was based on the appearance of bullet and jet perforations in neat and gel cements largely done in the absence of a confining pressure more than 15 years ago. Discussion Literature A relatively weak cement has been recommended in the literature as having optimum properties for perforating. In 1947, Oliphant and Farris tested bullet perforating of neat cements at various curing times.' Some of the tests were made at down-hole conditions. They reported that the optimum cement strength for perforating was about 2,000 psi compressive strength. Enlarged holes occurred when strength was too low, and the cement shattered and cracked when the strength was too high. In 1951, Morgan and Dumbauld tested bullet and jet perforating of neat and gel cements at surface conditions.' They reported that optimum cement has a compressive strength less than 2,000 psi. In their tests at atmospheric pressure, high strength cement shattered and cracked when perforated. Thus, the optimum cement strength was based on the appearance of neat and gel cement after perforating. In 1953, Clark showed a relation between cement strength and fluid shutoff.' He concluded that a 500 psi compressive strength is required for good fluid shutoff and that maximum bonding ability is developed at approximately 1,000 psi compressive strength. In 1964, Bell and Shore invalidated most of the conclu sions by the previous authors when they demonstrated that atmospheric pressure tests cannot be used to determine casing deformation and damage that will result from perforating under down-hole conditions.' They showed that the higher the hydrostatic pressure, the more restricted will be the expansion of gases generated by the charge. Less casing deformation and damage occurs under down-hole conditions than at atmospheric pressure. In recent work, Bearden et al. reported that jet perforating at surface pressure with the hollow carrier gun caused the cement sheath to shatter and crack.' The perforating, however, did not seriously affect the pressure required to leak past the casing cement bond. Only three cementing mixtures were tested, and presumably they had strengths in excess of 2.000 psi. Bearden et al. also reported that the hydraulic bonding strength increased as the compressive strength increased. Their hydraulic test showed that approximately 1,000 psi pressure is sufficient to break the casing cement bond for a well aged neat Portland cement sheath. Unfortunately, the tests were not run with a confining pressure, so Bearden et al. were merely measuring the strength of their outer 8%-in. casing. In our investigation, we measured the hydraulic bond strength of cement to pipe under a confining pressure and found that the bond strength was not limited to 1,000 psi. Cement Bond The bond strength is a good criterion for measuring the effectiveness of cement in performing its main function, that of preventing interzonal communication of fluids behind the casing. Measuring bond strength after perforating should be a good quantitative method of determining optimum cement properties, and should be a better method than that used by previous investigators,11 ' who simply observed the appearance of the cement after perforating.

Jan 1, 1969