Search Documents

By Herbert Ives

THE incandescent gas mantle is of considerable interest from the standpoint of temperature measurement because it presents a series of apparent contradictions to the established laws of radiation on which are based some of our best methods of temperature determination. One of these contradictions is that the mantle of least brightness (of the commercial thoria-ceria group) is the one having the highest temperature; this, though explicable without any violation of radiation laws, was long a stumbling block to the understanding of the performance of the mantle. Another anomaly is that the energy radiated by the mantle decreases with the rise of temperature, thus apparently invalidating total radiation methods of pyrometry, based on the fourth-power law. The discussion of methods of measuring mantle temperature which follows, is largely taken from an extensive study of the physics of the Welsbach mantle. 1 The incandescent gas mantle consists of a skeleton of refractory oxide of very light weight and open structure, formed by the ignition of a cotton or silk "stocking" previously thoroughly impregnated with salts of certain rare earths. The mantle of commerce is a mixture of approximately 99 parts of thorium oxide with 1 part of cerium oxide. This mixture, discovered largely by accident, gives luminous radiation many times greater than that from either of the constituents taken alone. It is customary to speak of the thoria as the "base" and the ceria as the "colorant," and the commercial mantle represents one of a family in which an oxide of low emissive power is employed as a base, which will assume a high temperature, while a small amount of some other oxide of high visible emissive power is added, which will reduce the temperature of the mantle but little. This is, in general, the most efficient- way, from the standpoint of visible emission, to utilize a substance of high emissive power in the visible spectrum. But it is not necessary. that two substances should be employed to produce a radiator

Jan 9, 1919

By E. A. Moulder

The mining industry is continually faced with problems involving dewatering, pollution, water supply, leaching and hydrochemical mining and prospecting. Greater application of the principles of ground-water hydrology to solution of these problems promises improved operating efficiency, increased safety and better public relations. Estimating the magnitude of dewatering for a proposed mine may be a major factor in determining the feasibility of proceeding with mine development. Diverting the source of ground water to an abandoned mine may save costly treatment of acid-mine drainage. Development of a large ground-water supply near an ore deposit may enhance the possibilities of a leaching operation. Detection of certain dissolved minerals in water from springs or wells may lead to hitherto unknown mineral deposits. Current efforts of industry, educational institutions and government are making these kind of events more commonplace. Dewatering of Mines The magnitude of dewatering problems was dramatized by a flooding that occurred last year in a gold mine in South Africa. During drilling operations at the West Driefortein mine, a major fracture was encountered from which large volumes of water issued necessitating evacuation of 1350 men from the mine. Dewatering required an increase in pumping of more than 80 million gpd. Models of ground-water systems are being used to test alternate plans for dewatering mines. Using the models in conjunction with computer optimization programs may lead to minimizing costs of operation. In addition to computer simulation of aquifers associated with phosphate deposits in North Carolina mentioned in last year's report, two USGS employees developed a model to estimate the amount of pumping required to dewater a mine site in Colorado.

Jan 1, 1970

By Robert H. Carpenter

Major trends in exploration geochemistry during the past year included an increased level of geochemical exploration by both government and private industry: greater sophistication in sampling, analytical and interpretive techniques: and increased activity on the part of universities and state geological surveys. The evolution of applied geochemistry in North America from a useful prospecting tool to an invaluable exploration method is largely due to efforts of the mining industry, the USGS and the Geological Survey of Canada. In the U.S., there has been a distinct reluctance on the part of universities to conduct research or to offer courses dealing principally with applied geochemistry. Most university geochemists have not been responsive to industry needs because government sponsorship of geochemical research in universities has been overwhelmingly in favor of theoretical, rather than applied research: and, because of the mistaken notion that exploration geochemistry is not sufficiently academic. A critical shortage of specialists in this field has resulted. Specialists in Exploration Geochemistry Needed Based on the response to a brief questionnaire sent to universities in the U.S. and Canada, there is some evidence suggesting a reversal in this trend. Graduate courses devoted to exploration geochemistry are currently being offered in geology departments at the following universities: University of British Columbia, Colorado School of Mines, University of Idaho, McGill University, University of New Mexico, Pennsylvania State University and the University of Utah. Other departments report that applied geochemistry is included in general geochemistry courses. A survey of recent publications suggests increased research interest in exploration geochemistry by university geologists.

Jan 1, 1970

By Robert L. Dean, Michael Hoch, Samuel M. Wolosin, Chung K. Hwu

The general shape of the 1450°C isotherm of the Ti-TiO-ZrO2-Zr region was evaluated from the surrounding binary phase diagrams and from thermo-dynamic data on the metal-oxygen binaries. The phase boundaries were accurately determined using X-ray and metallographic techniques. At 1450°C the system shows a large bcc ß field, which extends from the two metal-oxygen binary systems as a Gaussian error function, and is stable up to 30 at. pct 0 when Ti and Zr are present in equal amounts. At higher O Concentrations, the ß field is in equilibrium with t-ZrO . The following four regions, with three solid phases, are present: two a ß t-ZrO,, a TW t-ZrO,, and TiO t-ZrO2 c-ZrO2. On cooling the ß phase transforms into the a phase, going through the w transition phase. The isotherm at 1500°C for the region TiO-TiO,-ZrO, was obtained by using X-ray diffraction. At 1500°C a large c-ZrOz region is present as well as a large two-phase field, Ti0 c-ZrO,. The following regions, with three solid phases in equilibrium, were found These regions are relatively small. The solidus and liquidus relationships were determined by observing samples suspended in a tungsten crucible by means of a fine tungsten wire and heated in vacuum. Eleven univariant points were found. C-ZrO, decomposes through a peritectic reaction into liquid t-ZrO2. The activities of Ti and TiO in the TiO t-ZrOz and in the two a ß t-ZrO regions were measured using the Knudsen effusion method. In the a TiO t-ZrO, region the activities of Ti and Ti are the same, as in the a — Ti TiO binary. In the two a t-ZrO, regions, the Ti activity is high and the Ti0 activity very low, although all phases present contain at least 30 at. pct 0. This indicates a short-range order in the solid phases, Zr atoms being preferentially surrounded by 0. 1 HE system Ti-Zr-0 is of interest because of the wide ranges of solid solubility exhibited by the boundary systems; as titanium and zirconium both belong to the same group of the periodic table, large single-phase regions should occur within the system, with a great variation of properties (as the composition changes within the single-phase region). Furthermore, the possibility of modifying ZrO, to make it a more usable refractory by the addition of other metals makes this system also of interest. Because of the high affinity of titanium and zirconium for oxygen, the oxygen partial pressure is very low at all compositions; thus, there exists a ternary metal-metal-oxygen system in which the oxygen pressure is not an important variable, so long as it is low enough. When a sample is heated in vacuum to a temperature high enough for vaporization to occur, the vapor phase will consist of metal and metal-oxide gas, the oxygen concentration being very low. The phase relationships in the surrounding binary systems have already been reported in the literature; therefore, the study of the ternary diagram

Jan 1, 1962

By Gerald F. G. Sherman

The ore deposits of the Warren district, in which the mines of the Copper Queen Consolidated Mining Co. are situated, have been described in a number of technical publications, and will not be discussed here in detail. Certain of their characteristics, however, control methods of underground transportation and hoisting of ore. In the Copper Queen mine, the majority of the ore has occurred in a zone encircling the west boundary of the porphyry intrusion of Sacramento Hill. It has a width varying from 800 to 1,200 ft., and a thickness of about 400 ft. It reaches the surface in the older part of the mine to the northwest, but dips to the southeast, where it is reached at 1,400 ft. below the Czar collar, in its farthest extension at present developed on Copper Queen ground. There is one major extension from the northwest end of the zone toward the west along the Czar fault, and others of minor importance. Individual orebodies are scattercd through the zone in an eccentric manner, only matched by their own irregularities of form and size. Their most gencral characteristics are the softness of the ore and their grcat horizontal rather than vertical extent. It has been estimated that the average vertical thickness of ore in the Czar and Lowell divisions is between 30 and 35 ft. It is calculated by assuming it to be uniformly distributed over its horizontally projected area. In this zone, and for some distance above it, the ground has been subjected to intense alteration and intense but irregular oxidation. It has resulted in an enormous quantity of earthy or clayey material, which may be either ore or waste, which when wet is both heavy and tenacious. Below alteration, the ground is fairly hard, and the limestones contain primary ores differing from those heretofore considered typical of the camp, and which have not yet been thoroughly exploited. The mine production has been drawn from many orebodies spread over a great area.l A diagram map (Fig. I), of haulage drifts and loading stations, illustrates the situation in 1914.

Jan 1, 1916

By A. W. Schlechten, C. M. Hsiao

J. Pearson (British Iron and Steel Research Association, London, England)—Dr. Wagner has referred to the work of Richardson and Dancy and Gellner and Richardson on the reduction at 900°C of wustite films on iron. He has assumed that iron ions and electrons migrate backwards to the iron-wustite interface and that the reduced iron grows on the metal substrate. This would be a possible explanation of the results of these workers were it not for the fact that, as stated by Gellner and Richardson but not stressed, this growth in the center of the specimen can occur even

Jan 1, 1953

By Robert R. Britton

A study conducted at The Ohio State University sought to deter- mine whether explosives break rock primarily employing shock energy or energy stored as borehole gas pressure. The amount of broken material, calculated borehole pressure, and measured stress waves are compared as decoupling ratios (borehole diameter/explosive charge diameter) increased from 1 to 3 and all other variables remained constant. Breakage and calculated borehole pressure displayed a decrease as the decoupling ratio increased while the shock energy remained constant. The strong implication is that borehole gas pressure is the primarary force in breaking rock with explosives.

Jan 1, 1984

By Carl Wagner

J. Pearson (British Iron and Steel Research Association, London, England)—Dr. Wagner has referred to the work of Richardson and Dancy and Gellner and Richardson on the reduction at 900 °C of wiistite films on iron. He has assumed that iron ions and electrons migrate backwards to the iron-wustite interface and that the reduced iron grows on the metal substrate. This would be a possible explanation of the results of these workers were it not for the fact that, as stated by Gellner and Richardson but not stressed, this growth in the center of the specimen can occur even

Jan 1, 1953

By C. Morrow

Deformation studies were performed on tuffaceous rocks fran Yucca Mountain, Nevada Test Site to determine the strengths and coefficients of friction under confining pressures from 10-50 MPa at room temperature. Frictional strengths of 30ºsawcut samples increased with pressure and reached values of around 150 MPa at the higher confining pressures. However, the failure strengths of the intact samples were quite unpredictable. The coefficients of friction ranged between 0.7 and 0.9 for all specimens. These data can be used in conjunction with in situ stress measurements at Yucca Mountain, to evaluate the potential for earthquake activity in the region.

Jan 1, 1984

By D. P. Seraphim

Single crystals of bee Li-Mg solid solution were grown and their internal friction was measured as a function of temperature, A peak of the Zener type was found in the damping spectrum. The activation energy for the relaxation process is 21.5 ± 1 kcal per mole and the frequency factor is 1015.7 ± 0.7 sec-1. ZENER internal-friction peaks which are observed for a wide range of solid solutions are attributed to stress-induced changes in local order.' In the present work a Zener internal-friction peak, the first reported for a solid solution of an alkali metal, is

Jan 1, 1961

By N. S. Parate

Detailed analysis is given of the influence of water on the strength of limestone. The mechanism involved in strength reduction is described. Such analysis is of importance in geological, civil, constructional, mining, and metallurgical engineering and is closely associated with the rock mechanics involved in these areas. Mine dumping, slope stability, excavations, sedimentation, etc., are very much affected by the presence of water. Tensile stresses, which have an important role in the development and propagation of fissures, are produced by water in cracks. The development of fissures can be responsible over a long period of time for an ultimate, catastrophic failure.

Jan 1, 1974

By John R. Wynnyckyj

Results of correlations between strength-development and sintering shrinkage occurring during induration are presented. A mathematical treatment of the shrinkage kinetics is, next, given and is based on the use of semi-empirical equations. The discussion stresses the significance of kinetic constants and activation energies in the assessment of iron ore concentrates for pelletizing and induration. Next, starting with the assumption that there is a need for parameters to characterize the iron-ore concentrates and relate these parameters to shrinkage-kinetic constants and balling behaviour, results of compaction measurements and pore structure characterization (mercury porosimetry) are presented and discussed.

Jan 1, 1977

By Paul M. Tyler

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance.

Jan 9, 1953

By Thiann R. Yu, William J. Quesnel

At Kidd Creek, the annual production of 4.5 million tonnes of ore has been achieved primarily with sublevel blasthole stoping. This mining method has allowed underground operations to meet the designed production capacity while maintaining an outstanding safety record. To achieve this goal, rock mechanics principles have been integrated into each facet of mining in the planning stage, in the production stage, and in various stages of ground support. This paper evaluates the two adopted mining sequences based on ground stress patterns, blasting control, ground reinforcement, backfill support, and numerical modelling for stope stability at the mines.

Jan 1, 1984

By J. B. Sellers, G. R. Haworth, P. G. Zambas

Rock mechanics research was carried out in the Anvil Points mine, Rifle, Colo., in the period 1964-1968, with the dual purpose of providing oil shale to the retorts of six major oil companies and to perform research on mining cycle operations to maximize extraction under safe conditions. An 80% extraction ratio within the mining area proved feasible. Test results provided data on optimum pillar and roof design. Studies of mine orientation showed that the mining headings should take into account the prevailing joint patterns and also the directions of the principal in-situ stresses acting in the region.

Jan 1, 1973

By John Birkinbine

The press, trade publications, and special circulars, some elaborately illustrated, have been liberally employed within recent years in this country, to set forth the advantages of various locations as industrial centers, having as a basis the possibility of profitably producing pig-iron at these proposed centers: and special stress has been placed upon opportunities believed to exist at certain points for making iron of a quality suitable for the manufacture of Bessemer steel. The remarkable statements and prophecies made in some of these publications, have suggested the present paper, treating of the influence which location exerts upon the special industries named.

Jan 1, 1893

By William H. Baer, George M. Carlton, Blake M. Loring

IT is a well known fact that age-hardening alloys remain in a supersaturated, or partially supersaturated, condition only for limited periods of time at temperatures below the solvus. In order to develop optimum properties by subjecting the quenched alloy to precipitation or age-hardening treatment at a specified temperature, it is necessary that the cooling rate be sufficiently high to maintain the required degree of supersaturation of the solid solution. In practical applications the size and shape of the specimens obviously have considerable influence on the rate of cooling and there is need for more information on the effects of various rates of cooling. Cooling rates of quenched aluminum alloys generally have been established by the type of quenching medium, the temperature of the medium and the dimensions of the specimen.1,2,3 Except for the work of Roth3 little quantitative information is available on the measurement of cooling rates of aluminum alloys and the significance of the influence of various cooling rates upon the mechanical properties. The purpose of the present investigation was to study the use of the Jominy test for aluminum alloys (Table I). EXPERIMENTAL PROCEDURE The material for this investigation consisted of extruded rods 1 ¼ to 1 ½ in. in diam. The chemical compositions were as follows: [ ] The modified L-type Jominy specimen with dimensions shown in Fig I was selected as the most convenient means for obtaining a wide range of cooling rates. The standard Jominy specimen was not satisfactory because its cooling rate was not sufficiently high. The four flat surfaces machined at right angles along the length of the L-type specimen to a depth of 0-015 in. facilitated the hardness measurements. The specimens were machined from the extruded stock with no intermediate forging. New specimens were used for each aging experiment. The specimens were given solution treatments of 2 hr duration at recommended temperatures in a Hoskins furnace (Table 2). The temperature of the furnace was maintained constant to ±3°C. No protective atmosphere was necessary because the thin film of oxide that formed on the surface of the specimens had no effect on the hardness measurements.

Jan 1, 1948

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1944

By Howard L. Hartman

There is reason to believe that ventilation systems so far devised for use with continuous mining machines fall far short of success. This is vividly demonstrated to anyone who has observed in a continuous miner section the localized ignitions of pockets of gas and the generation of dense clouds of dust by the cutting head of the machine. The alarming frequency with which major ignitions and disasters continue to occur in modern mechanical mining and the rise in incidence of pneumoconiosis serve as reminders that our ventilation systems are far from achieving the ultimate in providing protection from either short-term explosions or long- term dust diseases, both of which take lives. Human safety is the main concern in ventilation. But in this day of high-priced labor, let us not forget human comfort, either, for this is a major factor in motivation toward high productivity. The failure or inadequacy of most mine ventilation systems in providing the kind of working conditions at the face that are conducive to productive as well as safe operation is an indictment of our environ- mental control program in mining generally.

Jan 3, 1962

By Frank E. Neil, O&apos

The formation tester, as the name implies, is a tool built for testing the contents of sands encountered in drilling Wells Without actually cementing casing on the sand. The tester was developed in the Mid-Continent and has been in use commercially there since about 1926. However, some two dozen patents have been issued on formation testers dating back to the seventies. The method apparently was an outgrowth of the old Mother Hubbard grain or bean packer, used around casing before the days of cementing casing. These packers were also seated in a tapered hole and if the formation tested was not satisfactory the casing was pulled loose and the hole taken down to another formation. A great deal of experimental work has been done in its development, and as a result of this work the formation tester became an accepted integral part of the petroleum development in California. The formation tester was introduced into California some three years ago by M. 0. Johnston. Months of discouraging and expensive work followed its introduction into this state, but one organization after another tried the tool and its use is now fairly general. Shortly after Johnston began testing in California, the Halliburton tester was also introduced into the state and now another tool is being introduced, the Shaffer-Roles tester. Principle and Operation of Testers The principle employed in all formation testers is that of packing off the fluid in the hole above the formation to be tested and thereby prevent,ing it from having access to the testing tool. This permits the fluid contained in the given formation to have unrestricted access to the tool. It is accomplished by running the tool and packer on the bottom of the drill pipe; the valves in the tool being closed while going into the hole to prevent fluid from entering the drill pipe. The packer is then seated at the desired point, trapping the drilling fluid above it. When this has been done, the valves in the tool are opened and the fluid from the formation is allowed to enter the empty pipe through the tool. If the

Jan 1, 1934